Victron Energy Skylla-i 24V 80A (1+1) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024080000 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 16 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 80 A Charge current starter batt. (A): 4 A Charge algorithm: 7 stage adaptive Battery capacity (Ah): 400-800 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 80A (3) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024080002 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 16 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 3 x 80 A Charge current starter batt. (A): n. a. Charge algorithm: 7 stage adaptive Battery capacity (Ah): 400-800 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 100A (1+1) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024100000 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 20 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 100 A Charge current starter batt. (A): 4 Charge algorithm: 7 stage adaptive Battery capacity (Ah): 500-1000 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 100A (3) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024100002 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 20 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 3 x 80 A Charge current starter batt. (A): n.a Charge algorithm: 7 stage adaptive Battery capacity (Ah): 500-1000 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 12/70(1+1) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge Algorithmsuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and a wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located in the world.Skylla-IP65 (1+1): two outputs to charge 2 battery banksThe Skylla-IP65 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A trickle charge and with a slightly lower output voltage, is intended to top up a starter battery.IP65 Rating ProtectionWith a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions.Victron Energy SKY012070000 Features: LCD Display: For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation: Several chargers can be connected in parallel and synchronised with help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, the charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 12/70(3) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located.Victron Energy SKY012070100 Features: Skylla-IP65 (3): three full current outputs to charge 3 battery banks. The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full-rated output current IP65 Rating Protection With a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation Several chargers can be connected in parallel and synchronised with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, a Skylla-i Control panel, or the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 24/35(1+1) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located.Victron Energy SKY024035000 Features: Skylla-IP65 (1+1): two outputs to charge 2 battery banks. The Skylla-IP65 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A trickle charge and with a slightly lower output voltage, is intended to top up a starter battery. IP65 Rating Protection. With a steel epoxy powder-coated case the Skylla is built to withstand the rigours of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display.For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronized Parallel Operation. Several chargers can be connected in parallel and synchronized with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use. The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready. Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life. The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000). To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 24/35(3) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located in the world.Victron Energy SKY024035100 Features: Skylla-IP65 (3): three full current outputs to charge 3 battery banks. The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full-rated output current IP65 Rating Protection With a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation Several chargers can be connected in parallel and synchronised with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Monocrystalline Solar Panels 20W 12V 440 x 350 x 25mm: Designed to Charge your 4WD, RV and Marine Batteries Victron Energy SPM040201200 Features: A low voltage-temperature coefficient enhances high-temperature operation Exceptional low-light performance and high sensitivity to light across the entire solar spectrum 25-year limited warranty on power output and performance 5-Year Limited warranty on materials and workmanship The sealed, waterproof, multifunctional junction box gives a high level of safety High-performance bypass diodes minimize the power drop caused by shade Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance Victron Energy SPM040201200 Specifications: Nominal Power: 20W Max-Power Voltage: 18.5V Max-Power Current: 1.09A Open-Circuit Voltage: 22.6V Short-Circuit Current: 1.19A Cell type: Monocrystalline Number of cells in series: 36 Temperature Range: -40¬∞C to +85¬∞C Surface Maximum Load Capacity: 200 kg/m¬≤ Allowable Hail Load: 23 m/s, 7.53 g Junction Box Type: PV-LH0801 Length of Cables / Connector Type: No cable Output tolerance: +/-3% Frame: Aluminium Smallest packaging unit: 1 panel Quantity per pallet: 380 Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less