Professional 6-channel Class D amplification engineered specifically for 24V commercial marine vessels and heavy vehicle applications. Product Overview The JL Audio XDM600/6-24V 6-channel amplifier delivers comprehensive full-range amplification for 24V electrical systems found in commercial vessels, charter boats, coach buses, and heavy transport applications. With 100W RMS per channel at 2Ω (600W total) or 75W per channel at 4Ω (450W total), this marine-rated Class D platform drives complete audio systems including cabin speakers, cockpit zones, and helm areas from a single compact chassis. The 24V-specific design operates optimally at 22-29V input—the native voltage range of diesel-powered vessels and commercial vehicles with dual 12V battery configurations wired in series. Built using JL Audio's advanced NexD™ high-speed switching design, the 6-channel configuration allows flexible system architecture: run all six channels independently, bridge pairs for higher power (200W per bridged pair), or configure as a staggered-power system with bridged front channels and unbridged rear channels. Variable high-pass and low-pass filtering on all three channel banks (50Hz-500Hz, 12dB/octave slopes) enables precise tuning for different speaker types and mounting locations. At 216mm wide with marine-grade construction and a 30A fuse rating, the XDM600/6-24V represents the ideal 24V amplification solution for Australian charter operators, commercial fishermen, and fleet managers demanding reliability in harsh coastal conditions. Key Specifications 6-channel Class D amplifier designed for 24V electrical systems Maximum rated power (28.8V @ 2Ω, <1% THD): 100W RMS × 6 channels (600W total) Power at 4Ω load (28.8V @ 4Ω, <1% THD): 75W RMS × 6 channels (450W total) Bridged power (28.8V @ 4Ω, <1% THD): 200W RMS × 3 channels (600W total bridged) Power at 2Ω load (25V @ 2Ω, <1% THD): 90W RMS × 6 channels (540W total) Power at 4Ω load (25V @ 4Ω, <1% THD): 60W RMS × 6 channels (360W total) Bridged power (25V @ 4Ω, <1% THD): 180W RMS × 3 channels (540W total bridged) Operating voltage: 22-29V DC (24V systems only) Frequency response: 12Hz-22kHz (+0, -1dB) Signal-to-noise ratio: >104dB (A-weighted, 20Hz-20kHz, referred to highest rated power) Signal-to-noise ratio: >84dB (A-weighted, 20Hz-20kHz, referred to 1W) Damping factor @ 4Ω: >150 @ 50Hz Damping factor @ 2Ω: >75 @ 50Hz THD+N: <1% @ rated power, 2Ω per channel Input channel modes: 2-channel or 4-channel Filter modes (Channels 1 & 2, 3 & 4, 5 & 6): Off, Low-Pass, or High-Pass Filter slope: 12dB/octave Filter frequency range: 50Hz-500Hz Infrasonic filter: No Buffered pass-through preamp outputs: Yes Dimensions: 216mm (W) × 180mm (D) × 52mm (H) Weight: Not specified Fuse rating: 30A (AFS, AGU or MaxiFuse™ recommended) Minimum power/ground wire: 4 AWG copper Remote level control: Optional HD-RLC or MHD-RLC (water-resistant) Automatic turn-on: Signal sensing or DC-offset sensing Marine-grade construction with gasketed removable top cover 3-year manufacturer warranty Features & Benefits 24V Commercial Marine DesignPurpose-built for 24V electrical systems common in commercial vessels, charter boats, and heavy transport. Unlike 12V amplifiers that require voltage adaptation, the XDM600/6-24V operates optimally at 22-29V input—the native voltage range of diesel-powered boats, coach buses, and commercial fishing vessels with dual 12V batteries wired in series. Eliminates the need for voltage converters or multiple 12V amplifiers in 24V installations, simplifying electrical infrastructure and reducing potential failure points. Flexible 6-Channel ArchitectureConfigure for multiple installation scenarios: run all six channels independently (75-100W each) for complete cabin coverage, bridge three pairs for 200W outputs to demanding speakers, or create a staggered-power system with 200W × 2 bridged for front zones plus 75W × 2 unbridged for rear fill. The channel bank design (1&2, 3&4, 5&6) allows independent filtering and level adjustment per zone, perfect for commercial vessels requiring helm, cockpit, and cabin zones with different speaker requirements. Advanced NexD™ Class D TopologyJL Audio's proprietary NexD™ high-speed switching design delivers full-bandwidth Class D operation with exceptionally low distortion and remarkable efficiency. The marine-grade conformal coating resists salt spray, bilge moisture, and corrosive environments encountered in Australian commercial fishing, charter operations, and offshore work vessels. Robust construction handles tropical humidity in Far North Queensland, Southern Ocean conditions off Tasmania, and everything between—engineered for installations where amplifier failure isn't an option. Variable Filtering Across All Three Channel BanksPrecision crossover control on channels 1&2, 3&4, and 5&6 allows system-specific tuning. High-pass filter cabin speakers to remove low-frequency strain, low-pass subwoofer channels for dedicated bass reproduction, or run full-range where needed. The 12dB/octave slopes and 50Hz-500Hz continuously variable range accommodate any speaker configuration, from compact marine coaxials to high-output tower speakers. Independent filter control per channel bank enables sophisticated system design with multiple speaker types in different zones. Compact 24V Power DistributionThe 30A fuse rating and 4 AWG wire compatibility simplify installation in commercial vessels with existing 24V distribution systems. At just 216mm wide, the compact chassis fits shallow-mount locations behind helm panels, under seats, or in equipment bays where larger amplifiers won't fit. The gasketed, removable top cover protects controls from moisture ingress while enabling easy access for tuning and adjustment during commissioning or seasonal maintenance. Automatic Turn-On CapabilityDual-mode turn-on detection (signal sensing or DC-offset sensing) enables seamless integration with factory audio systems or aftermarket source units. Eliminates the need for separate remote turn-on wiring in many installations, simplifying OEM integration for commercial fleet applications. Critical for charter vessels and work boats where installers need reliable operation without complex wiring modifications to factory electrical systems. Optional Water-Resistant Remote ControlAdd JL Audio's HD-RLC or MHD-RLC (not included) for convenient output adjustment from the helm, flybridge, or entertainment zone. The remote provides level adjustment for two, four, or all six channels directly from the driver's seat or cockpit. Essential for commercial charter operators who need guest-accessible volume control, or fishing guides adjusting audio levels between travel and fishing modes without accessing the amplifier installation location. Technical Specs Amplifier class: Class D (NexD™ high-speed switching design) Channels: 6 (Full-range) Operating voltage: 22-29V DC (24V systems only - NOT compatible with 12V systems) Power Output (varies by voltage and load impedance): Maximum rated power (28.8V @ 2Ω, <1% THD): 100W RMS × 6 (600W total) Power at 4Ω load (28.8V @ 4Ω, <1% THD): 75W RMS × 6 (450W total) Bridged power (28.8V @ 4Ω, <1% THD): 200W RMS × 3 (600W total bridged) Power at 2Ω load (25V @ 2Ω, <1% THD): 90W RMS × 6 (540W total) Power at 4Ω load (25V @ 4Ω, <1% THD): 60W RMS × 6 (360W total) Bridged power (25V @ 4Ω, <1% THD): 180W RMS × 3 (540W total bridged) Frequency response (+0, -1dB): 12Hz-22kHz Signal-to-noise ratio (A-weighted, 20Hz-20kHz, referred to highest rated power): >104dB Signal-to-noise ratio (A-weighted, 20Hz-20kHz, referred to 1W): >84dB Damping factor @ 4Ω: >150 @ 50Hz Damping factor @ 2Ω: >75 @ 50Hz THD+N @ rated power: <1% @ 2Ω per channel Input channel modes: 2-channel or 4-channel selectable Filter modes (Channels 1&2, 3&4, 5&6): Off, Low-Pass, or High-Pass Filter slope: 12dB/octave Filter frequency range: 50Hz-500Hz (continuously variable) Infrasonic filter: No Buffered pass-through preamp outputs: Yes Remote level control compatibility: Optional HD-RLC or MHD-RLC (water-resistant) Automatic turn-on: Signal sensing or DC-offset sensing Recommended fuse type: AFS, AGU or MaxiFuse™ Fuse rating: 30A Minimum copper power/ground wire gauge: 4 AWG Physical dimensions (W × D × H): 216mm × 180mm × 52mm (8.52" × 7.09" × 2.05") Weight: Not specified Construction: Marine-grade materials with gasketed removable top cover Finish: Black powder-coat Water rating: Not rated (marine-grade construction, not waterproof) Warranty: 3 years Important Note: This is a 24V-specific model designed for commercial marine vessels, heavy vehicles, and applications with dual 12V batteries in series. It is NOT compatible with standard 12V automotive/marine electrical systems. Operating voltage range is 22-29V DC. Use in vessels with positive ground and/or voltages other than 24V will result in damage and void the warranty. Compatible With / Goes Well With Speaker Recommendations: Marine coaxial speakers rated 75-100W RMS (6", 6.5", or 6×9" sizes) Marine component speaker systems rated 75-100W RMS per channel Marine tower speakers rated 150-200W RMS per speaker (when bridged) Compact marine subwoofers rated 200W RMS (when using bridged channel pairs) Full-range cabin speakers for multi-zone installations Installation Accessories: 4 AWG amplifier wiring kit designed for 24V systems with 30A+ inline fuse holder JL Audio HD-RLC or MHD-RLC water-resistant remote level control Marine-grade speaker wire (14-16 AWG recommended for most runs) RCA interconnect cables with marine-grade shielding 24V-compatible distribution blocks for multi-amplifier systems Heavy-duty amplifier mounting brackets or marine-rated equipment racks System Compatibility: Marine head units with 24V DC operation and preamp outputs Commercial marine audio processors with 24V compatibility 24V electrical systems (dual 12V batteries in series configuration) Charter vessels, commercial fishing boats, work boats with 24V infrastructure Coach buses, heavy transport vehicles with 24V electrical systems Electrical System Requirements: Confirmed 24V DC electrical system (22-29V operating range) Dual 12V batteries wired in series for 24V output Adequate alternator capacity for continuous audio operation Proper 24V distribution with circuit protection Dedicated ground point to hull/chassis (negative ground systems only) Caution: This amplifier requires a 24V negative-ground electrical system. It will NOT operate on standard 12V automotive/marine systems. Verify your vessel or vehicle operates at 24V before ordering. Use in vessels with positive ground and/or voltages other than 24V will result in damage to the product and void the warranty. For 12V applications, consider the standard XDM 6-channel 12V variant. Frequently Asked Questions Is this amplifier compatible with my 12V boat electrical system?No. This model requires a 24V DC negative-ground system (22-29V input range). It's designed for commercial vessels, charter boats, and heavy vehicles with dual 12V batteries wired in series. Attempting to use it on a 12V system will result in insufficient power and potential damage. For 12V applications, you need the standard XDM 6-channel 12V model. Can I bridge channels for higher power to tower speakers or subwoofers?Yes. Bridge adjacent channel pairs (1+2, 3+4, 5+6) for 200W RMS per bridged pair at 4Ω load (28.8V input). This allows three bridged outputs at 200W each, ideal for marine tower speakers or subwoofers requiring more power than single-channel 100W output. You can also mix configurations: bridge channels 1+2 and 3+4 for 200W front speakers, leave channels 5&6 unbridged for 75W rear fill. What is the staggered-power configuration mentioned in the description?Bridge four channels (1+2 and 3+4) for 200W × 2 @ 4Ω to front speakers, while leaving channels 5&6 unbridged for 75W × 2 @ 4Ω to rear speakers. This provides maximum power where needed (front soundstage) while conserving electrical capacity for rear fill. Alternatively, bridge channels 1+2 and 3+4 for two subwoofers at 200W each, plus channels 5&6 for satellite speakers at 75W × 2. How does the automatic turn-on work without a remote wire?The amplifier features dual-mode detection: signal sensing (detects audio signal on RCA inputs) or DC-offset sensing (detects DC voltage from source unit). This enables integration with factory systems that don't provide remote turn-on output. Select the appropriate mode based on your source unit—signal sensing for aftermarket units, DC-offset for many factory systems. Eliminates complex wiring modifications in commercial fleet installations. What does "marine-grade construction" mean if it's not waterproof?Marine-grade construction includes conformal-coated circuit boards to resist salt spray, moisture, and corrosion in marine environments. The gasketed removable top cover protects controls from moisture ingress. However, the amplifier is not waterproof/submersible—mount away from direct water streams, bilge flooding, or areas subject to washdown. Suitable for protected equipment bays, under helm panels, or in cabin locations with normal marine moisture exposure.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Versatile 6-channel Class D amplification engineered for complete marine and automotive multi-zone audio systems. Product Overview The JL Audio XDM600/6 6-channel amplifier delivers comprehensive full-range amplification for multi-zone marine installations, automotive touring setups, and enthusiast builds requiring complete speaker control from a single chassis. With 100W RMS per channel at 2Ω (600W total) or 75W per channel at 4Ω (450W total), this marine-rated Class D platform drives cabin speakers, cockpit zones, tower speakers, and helm areas independently. The 12V design integrates seamlessly into standard automotive and marine electrical systems while the conformal-coated construction withstands Australia's harshest coastal conditions, bilge moisture, and dusty 4WD environments. Built on JL Audio's proven XDM architecture, the 6-channel configuration enables sophisticated system design: run all six channels independently for maximum zone control, bridge adjacent pairs for 200W output to demanding tower speakers or compact subwoofers, or create staggered-power configurations with bridged front channels and unbridged rear fill. Variable filtering on all three channel banks (channels 1&2, 3&4, 5&6) with 50Hz-500Hz range and 12dB/octave slopes accommodates different speaker types and mounting locations. At 260mm wide with a 50A fuse rating and 2.63kg weight, the XDM600/6 represents the ideal multi-zone amplification solution for Australian marine enthusiasts, ski boat owners, and 4WD tourers. Key Specifications 6-channel Class D amplifier optimised for full-range multi-zone applications Maximum rated power (14.4V @ 2Ω, <1% THD): 100W RMS × 6 channels (600W total) Power at 4Ω load (14.4V @ 4Ω, <1% THD): 75W RMS × 6 channels (450W total) Bridged power (14.4V @ 4Ω, <1% THD): 200W RMS × 3 channels (600W total bridged) Power at 2Ω load (12.5V @ 2Ω, <1% THD): 90W RMS × 6 channels (540W total) Power at 4Ω load (12.5V @ 4Ω, <1% THD): 60W RMS × 6 channels (360W total) Bridged power (12.5V @ 4Ω, <1% THD): 180W RMS × 3 channels (540W total bridged) Operating voltage: 11-14.5 VDC (12V systems only) Frequency response: 12Hz-22kHz (+0, -1dB) Signal-to-noise ratio: >104dB (A-weighted, 20Hz-20kHz, referred to highest rated power) Signal-to-noise ratio: >84dB (A-weighted, 20Hz-20kHz, referred to 1W) Damping factor @ 4Ω: >150 @ 50Hz Damping factor @ 2Ω: >75 @ 50Hz THD+N: <1% @ rated power, 2Ω per channel Input voltage range: Not specified for 6-channel (other multi-channel models: 200mV-4V RMS) Filter modes (Channels 1&2, 3&4, 5&6): Off, Low-Pass, or High-Pass Filter slope: 12dB/octave Filter frequency range: 50Hz-500Hz Detented, calibrated filter potentiometers: Yes Buffered pass-through preamp outputs: Not specified for 6-channel Dimensions: 260mm (W) × 180mm (D) × 52mm (H) Weight: 2.63kg (5.8 lbs) Fuse rating: 50A (AFS, AGU or MaxiFuse™ recommended) Minimum power/ground wire: 4 AWG copper Remote level control: Optional HD-RLC or MHD-RLC (water-resistant) Marine-rated construction suitable for wet/harsh environments 3-year manufacturer warranty Features & Benefits 6-Channel Multi-Zone FlexibilityDrive complete audio systems from a single amplifier installation. Allocate channels strategically: four channels for cabin coaxials, two bridged pairs for tower speakers at 200W each, or six channels for full cabin coverage with independent zone control. Perfect for ski boats requiring cockpit, cabin, and tower zones, or 4WD tourers with front cabin, rear cargo, and rooftop speaker zones. Eliminates the complexity and wiring bulk of multiple smaller amplifiers while providing professional-grade zone control. 12V Standard Electrical IntegrationDesigned for conventional 12V automotive and marine electrical systems (11-14.5V operating range). Integrates directly into factory or aftermarket head unit systems without voltage converters or special infrastructure. The 50A fuse rating and 4 AWG wire compatibility match standard marine and automotive electrical practices, simplifying professional installations and DIY builds alike. Compatible with AGM, lithium, or standard flooded batteries common in Australian recreational vehicles and vessels. Independent Channel Control with Bridge CapabilityRun all six channels independently at 75-100W each for maximum zone control, or bridge adjacent pairs (1+2, 3+4, 5+6) for three outputs at 200W each. Bridge mode suits high-output tower speakers, marine subwoofers, or demanding full-range speakers requiring more power than single-channel output. Mix configurations within the same installation: four unbridged channels for cabin speakers plus one bridged pair for subwoofer duty, providing system design flexibility without multiple amplifiers. Marine-Rated Class D TopologyConformal-coated circuit boards resist salt spray, bilge moisture, and the corrosive environments encountered in Australian coastal boating, offshore fishing, and beach-launched vessels. The robust construction handles tropical humidity in Far North Queensland waters, dusty corrugated tracks in the Outback, and Southern Ocean conditions off Tasmania. Class D efficiency minimizes heat generation, enabling reliable operation in poorly ventilated equipment bays, under seats, or in enclosed amplifier racks without thermal shutdown. Variable Filtering Across All Three Channel BanksPrecision crossover control on channels 1&2, 3&4, and 5&6 allows speaker-specific tuning. High-pass filter cabin speakers to remove low-frequency strain and improve clarity, low-pass subwoofer channels for dedicated bass reproduction, or run full-range where needed. The 12dB/octave slopes and 50Hz-500Hz continuously variable range accommodate marine coaxials, component speakers, tower speakers, and compact subwoofers. Detented potentiometers enable repeatable settings across similar installations—critical for professional installers servicing multiple boats. Compact Chassis with Professional-Grade Heat ManagementAt 260mm (10.23") wide and just 2.63kg, the XDM600/6 fits shallow-mount locations behind helm panels, under seats, or in equipment bays where larger amplifiers won't fit. The efficient Class D topology and well-designed heat sink maintain stable operation across all six channels simultaneously, even during extended listening sessions at anchor, beach parties, or long-distance highway touring. The compact footprint doesn't compromise thermal performance—essential for sustained full-power operation. Optional Water-Resistant Remote ControlAdd JL Audio's HD-RLC or MHD-RLC (not included) to adjust system volume from the helm, driver's seat, or entertainment area. Essential for marine applications where the amplifier is mounted in inaccessible equipment bays, or automotive installations where the amp is hidden behind panels. The remote provides convenient master volume control without accessing the installation location, perfect for recreational boaters and touring enthusiasts. Technical Specs Amplifier class: Class D Channels: 6 (Full-range) Operating voltage: 11-14.5 VDC (12V models only - NOT 24V compatible) Power Output (varies by voltage and load impedance): Maximum rated power (14.4V @ 2Ω, <1% THD): 100W RMS × 6 (600W total) Power at 4Ω load (14.4V @ 4Ω, <1% THD): 75W RMS × 6 (450W total) Bridged power (14.4V @ 4Ω, <1% THD): 200W RMS × 3 (600W total bridged) Power at 2Ω load (12.5V @ 2Ω, <1% THD): 90W RMS × 6 (540W total) Power at 4Ω load (12.5V @ 4Ω, <1% THD): 60W RMS × 6 (360W total) Bridged power (12.5V @ 4Ω, <1% THD): 180W RMS × 3 (540W total bridged) Frequency response (+0, -1dB): 12Hz-22kHz Signal-to-noise ratio (A-weighted, 20Hz-20kHz, referred to highest rated power): >104dB Signal-to-noise ratio (A-weighted, 20Hz-20kHz, referred to 1W): >84dB Damping factor @ 4Ω: >150 @ 50Hz Damping factor @ 2Ω: >75 @ 50Hz THD+N @ rated power: <1% @ 2Ω per channel Filter modes (Channels 1&2, 3&4, 5&6): Off, Low-Pass, or High-Pass Filter slope: 12dB/octave Filter frequency range: 50Hz-500Hz (continuously variable) Detented, calibrated filter potentiometers: Yes Remote level control compatibility: Optional HD-RLC or MHD-RLC (water-resistant) Recommended fuse type: AFS, AGU or MaxiFuse™ Fuse rating: 50A Minimum copper power/ground wire gauge: 4 AWG Physical dimensions (W × D × H): 260mm × 180mm × 52mm (10.23" × 7.09" × 2.05") Weight: 2.63kg (5.8 lbs) Warranty: 3 years Important Note: This is the 12V model. The XDM series also includes a 24V 6-channel variant (XDM600/6-24V) for commercial/heavy vehicle applications—this model operates on standard 12V automotive/marine electrical systems only. Compatible With / Goes Well With Speaker Recommendations: Marine coaxial speakers rated 75-100W RMS (6", 6.5", 6×9", or 7.7" sizes) Marine component speaker systems rated 75-100W RMS per channel Marine tower speakers rated 150-200W RMS per speaker (when bridged) Compact marine subwoofers rated 200W RMS (when using bridged channel pairs) Full-range cabin speakers for multi-zone installations Installation Accessories: 4 AWG amplifier wiring kit with 50A+ inline fuse holder JL Audio HD-RLC or MHD-RLC water-resistant remote level control Marine-grade speaker wire (14-16 AWG recommended for most runs) RCA interconnect cables with marine-grade shielding (minimum 6-channel distribution) Distribution blocks for clean power/ground distribution Heavy-duty amplifier mounting brackets or marine-rated equipment racks Sound deadening material for mounting surfaces System Compatibility: Marine head units with 4V preamp outputs (6-channel preamp output or DSP required) Aftermarket head units with 6-channel preamp capability Marine DSP processors with 6-channel output Line output converters with 6-channel capability for factory radio integration 12V electrical systems with adequate alternator capacity (90A+ recommended) Electrical System Requirements: Minimum 90A alternator capacity for sustained full-power operation Adequate battery reserve (AGM or lithium recommended for extended engine-off listening) Proper grounding with dedicated ground point to chassis/hull 4 AWG power and ground wiring with proper routing and protection Caution: Six-channel systems require careful planning. Ensure your head unit or DSP provides six independent preamp outputs. Verify speaker impedances before bridging channels—bridged operation requires 4Ω minimum load per bridged pair. Running all six channels at maximum power simultaneously demands robust electrical infrastructure including high-output alternator, proper wiring gauge, and adequate battery capacity. Weight 2.63kg (5.8 lbs) Frequently Asked Questions Can I run this amplifier with a standard aftermarket head unit?Only if your head unit or DSP provides six independent preamp outputs. Most standard head units offer 2-4 channels of preamp output—you'll need a 6-channel DSP or signal processor to feed all channels. Alternatively, use a marine source unit with 6-channel capability or run the amplifier with fewer active channels. Can I bridge channels for higher power to tower speakers or subwoofers?Yes. Bridge adjacent channel pairs (1+2, 3+4, 5+6) for 200W RMS per bridged pair at 4Ω load. This provides three bridged outputs at 200W each, ideal for marine tower speakers or compact subwoofers. Ensure speakers are rated for 4Ω minimum impedance when bridging. You can also mix configurations: bridge two pairs, leave two channels unbridged. What size alternator do I need to run all six channels at full power?Minimum 90A alternator for sustained full-power operation. At maximum output (600W), the amplifier draws approximately 60-65A from the electrical system. Factor in other electrical loads (navigation, pumps, lights) and ensure your alternator provides adequate reserve capacity. Undersized alternators cause voltage drop and potential thermal protection shutdown. Can I use this in a ski boat with tower speakers and cabin speakers?Yes, perfect application. Bridge channels 1+2 and 3+4 for 200W × 2 to tower speakers, use channels 5&6 unbridged for 75W × 2 to cabin speakers. Alternatively, run all six channels unbridged for complete cabin/cockpit coverage at 75-100W per zone. The variable filtering allows precise tuning for different speaker types and mounting locations. How do I set up independent zone control for different areas?Use channels 1&2 for Zone 1 (cabin), 3&4 for Zone 2 (cockpit/tower), and 5&6 for Zone 3 (rear/helm). The optional HD-RLC remote controls master volume. For true zone-independent control, install separate zone controllers or use a DSP with zone management feeding the amplifier. The three independent filter banks allow different crossover settings per zone.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Highlights: Highlights: SPECIFICATIONS: FREQUENCY RESPONSE: 10 HZ TO 40 KHZ (-3DB @ 4 OHM RATED POWER) PEAK POWER OUTPUT: 1500W RATED POWER OUTPUT (4 OHM): 100 W RMS X 6 @ 28.8 V INPUT < 1% THD + N (EIA/CEA-490A) RATED POWER OUTPUT (2 OHM): 140 W RMS X 6 @ 28.8 V INPUT < 1% THD + N (EIA/CEA-490A) RATED POWER OUTPUT (4 OHM BRIDGED): 280 W RMS X 3 @ 28.8 V INPUT < 1% THD + N (EIA/CEA-490A) INPUT SENSITIVITY: 0.3 V TO 8 V RMS, USER ADJUSTABLE INPUT IMPEDANCE: 7K OHM NOMINAL HIGH-PASS/LOW-PASS FULL RANGE FILTER: YES, USER SELECTABLE FILTER CROSS-OVER FREQUENCY: 32 HZ TO 320 HZ, USER ADJUSTABLE BASS-BOOST: 0 TO 9 DB, USER ADJUSTABLE (ZONE 3 ONLY) OPERATING VOLTAGE: 21.6 V TO 32 V DC REMOTE SWITCH-ON: YES - 6 V THRESHOLD CURRENT CONSUMPTION (STANDBY): < 1 MA @ 28.8 V INPUT CURRENT CONSUMPTION (IDLE): < 1.25 A @ 28.8 V INPUT CURRENT CONSUMPTION (MAX): 35 A @ 28.8 V INPUT FUSE RATING: 3 X 20 A ATC BLADE-TYPE (SAE J1171 COMPLIANT) PROTECTION CIRCUITS: REVERSE-VOLTAGE, INPUT UNDER/OVER VOLTAGE, OVER-TEMPERATURE, OUTPUT SHORT-CIRCUIT OPERATING TEMPERATURE RANGE: 0 TO 50¬∞C (32 TO 122¬∞F) INGRESS PROTECTION RATING: DRY AREA INSTALLATION ONLY DIMENSIONS: 420 MM (L) X 210 MM (W) X 57 MM (H) OR 16-9-16" (L) X 8-1/4" (W) X 2-1/4" (H) WEIGHT: 5.15 KG OR 11.35 LBS. WITH COVER Legendary Products & Support From Authorized Dealers When you choose Fusion, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Fusion dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Fusion's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Fusion dealer today!

Read more less

It’s The Difference Between Hearing The Music And Feeling ItThese efficient, easy-to-install amplifiers work with your compatible Fusion stereo system1 and let you choose from monoblock, multichannel, and zone amplifier options.The Apollo amplifiers are designed to produce impressive power with less drain on your battery. The monoblock produces 650-watt RMS and the 4/6/8 channel amplifiers produce 150-watt RMS per channel. These amplifiers use the Easy Tune feature2, which automatically regulates audio settings. So, you can get the best quality sound without making manual adjustments. Some amplifiers distort audio when they add power. Ours are specifically designed with minimal distortion and noise, so you can enjoy high-quality audio, even at higher volumes. Identify electrical issues at a glance. These indicator lights will show you issues with electrical currents and shorts as well as temperature. Easily install the amplifiers on board with the included mounting brackets. The ignition-protected design helps prevent potential damage from overheating. The amplifier’s circuit board has been specially coated to provide extra protection from the marine elements. You can connect up to two speakers per channel, increasing setup options. The amplifiers are designed to last season after season. They have been tested for a high level of protection against salt fog, temperature, vibration, and UV. Add extra power to your system with this 2000-watt (650-watt RMS) monoblock amplifier that’s specifically designed to power a subwoofer. This 4-channel amplifier with 150-watt RMS per channel can power up to four pairs of speakers or two pairs of speakers and one subwoofer. It includes high-power mode adapters for simple bridging to increase power. This 6-channel amplifier with 150-watt RMS per channel can power up to six pairs of speakers or four pairs of speakers and one subwoofer. It includes high-power mode adapters for simple bridging to increase power. This 8-channel amplifier with 150-watt RMS per channel can power up to eight pairs of speakers or four pairs of speakers and two subwoofers. It includes high-power mode adapters for simple bridging to increase power. The compact zone amplifier provides audio zone expansion for high-quality sound in more areas on your boat. It’s compatible with 12- and 24-volt electrical systems.Features: Keep the music going for longer without draining your battery as quickly No more manual adjustments to your audio settings. The Easy Tune feature does it for you. A glance at the LED indicators lets you identify if the amplifiers have a short or if they’re overheating. These amps have less distortion and noise, so you enjoy quality audio. Mounting brackets are included for simple installation. Don’t worry about potential overheating damage with our ignition protection design. Specifications: Physical dimensions without bracket (LxWxH) 6 Channel: 11.69″ x 7.06″ x 1.75″ (297 x 180 x 45 mm) Physical dimensions with bracket (LxWxH) 6 Channel: 11.69″ x 7.06″ x 2.13″ (297 x 180 x 50 mm) Weight Monoblock/4 Channel: 6 Channel: 5.95 lb (2.7 kg) Water rating Monoblock/4/6/8 Channel: IPX2 Amplifier class Class-D CEA-2006 power rating 6 Channel: 150 watt RMS x 6 @ 14.4 V input - 4 ohm < 1% THD Total rated power output - 6 Channel: 290 watt RMS x 6 @ 14.4 V input - 2 ohm < 1% THD Total rated power output - 6 Channel: 580 watt RMS x 3 @ 14.4 V input - 4 ohm Bridged < 1% THD Peak power (Watts) 6 Channel: 1800 watts Input sensitivity 4/6/8 Channel: 1.6 V RMS Input impedance Monoblock/4/6/8 Channel: 22k ohm Operating voltage Monoblock/4/6/8 Channel: 10.8 V - 16 V DC Current draw, in standby/off using AMPLIFIER ON wire Monoblock/4/6/8 Channel: < 5 mA @ 14.4 V input Zone: < 1 mA @ 14.4 V input Current draw, on, no audio 6 Channel: < 1.32 A @ 14.4 V input Power-cable fuse or circuit breaker rating (not included) 40 A Ignition Safety Protected (SAE J1171) Yes Protection circuits Reverse voltage Input under/over voltage Over Temperature Output short circuit Operating temperature range 0° to 50° C Warranty 3 years Accessories: Cables & Chargers Connectors Mounts Compatible Devices: Apollo RA670 Apollo RA770 Apollo WB670 Fusion EL Series Marine Speakers Fusion FM Series Marine Speakers Fusion FM Series Marine Subwoofers Fusion RA210 Marine Stereo Fusion Signature Series 3 Marine Speakers Fusion Signature Series 3 Marine Subwoofers Fusion Signature Series 3 Marine Wake Tower Speakers Fusion XS Series Marine Speakers Fusion XS Series Marine Subwoofers What's in the Box: One Apollo monoblock amplifier One mounting bracket One power connector One speaker connector Four 8-gauge, flat-head self-tapping screws Four 8-gauge, pan-head self-tapping screws (for mounting bracket) Four screw covers Mounting template Installation instructions Important safety and product information (ISPI) Legendary Products & Support From Authorized Dealers When you choose Fusion, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Fusion dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Fusion's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Fusion dealer today!

Read more less