BAINTECH BT-ADD-35-033 CVT Transmission Recovery Treatment 180ml - Advanced Anti-Shudder & Friction Reducer for Push Belt & Chain CVT Transmissions Protect your CVT transmission from shuddering, slipping, and premature wear with BAINTECH CVT Transmission Recovery Treatment — a professional-grade transmission additive engineered to restore smooth operation, eliminate shudder, and extend CVT life in push belt and chain-type continuously variable transmissions. This advanced transmission treatment dramatically reduces friction by up to 90% through cutting-edge lubrication technology, eliminating the shuddering and hesitation that plague CVTs under load or during acceleration — works within minutes of addition to provide immediate anti-shudder protection and smooth power delivery — increases CVT transmission life while delivering fuel consumption savings of 10% or more through optimized friction management and improved efficiency — protects against wear and corrosion in the demanding high-pressure contact environment between CVT belts, chains, and pulleys where metal-to-metal contact creates extreme friction loads — boosts torque capacity allowing transmissions to handle higher power outputs without slipping or belt degradation — and contains patented anti-foaming agents ensuring gears and transmission components always receive optimal lubrication without air entrainment that causes cavitation damage. Developed using technology trusted by NASA for over 25 years and inducted into the NASA Space Technology Hall of Fame, this scientifically proven treatment prevents the expensive CVT replacement costs (often $5,000-$8,000+) that result from neglected transmission maintenance, providing Australian drivers with a cost-effective solution to restore CVT performance, eliminate annoying shudder, and protect one of the most expensive components in modern vehicles from premature failure. Product Overview The BAINTECH CVT Transmission Recovery Treatment represents specialized chemistry developed specifically for the unique demands of continuously variable transmissions, which operate fundamentally differently from conventional automatic or manual transmissions. CVT transmissions use a push belt or chain running between variable-diameter pulleys to provide infinite gear ratios, creating extreme metal-to-metal contact pressures (often exceeding 1000 MPa) that generate tremendous friction, heat, and wear. This constant high-pressure sliding contact makes CVTs particularly susceptible to shuddering (a vibration felt during acceleration or at specific RPM ranges), belt slippage under load, premature wear of belt and pulley contact surfaces, and transmission fluid degradation from extreme operating temperatures. The BAINTECH treatment addresses these CVT-specific challenges through advanced friction modifiers that dramatically reduce the coefficient of friction at belt/pulley contact points without causing slippage, anti-shudder compounds that eliminate the stick-slip vibration causing shuddering, anti-wear additives providing boundary lubrication protection during extreme pressure contact, and thermal stability improvers that maintain fluid performance at the elevated temperatures common in CVT operation. The patented anti-foaming agents are particularly critical in CVTs where fluid aeration causes pump cavitation, reduces hydraulic pressure control, and creates foam that prevents proper belt lubrication leading to slippage and wear. Australian drivers of CVT-equipped vehicles including Nissan Pathfinder, Toyota Corolla, Honda CR-V, Subaru Outback, and Mitsubishi Outlander choose BAINTECH CVT treatment to eliminate the frustrating shudder that develops around 40-60 km/h, restore smooth acceleration that makes CVTs enjoyable to drive, prevent the premature belt and pulley wear that leads to expensive replacement, and maximize the 10%+ fuel economy benefits CVT technology promises but often fails to deliver when transmissions aren't properly maintained. Key Features Dramatic Friction Reduction Up to 90% Reduces friction at critical belt/chain and pulley contact points by up to 90% through advanced friction modifier chemistry that creates ultra-low-friction boundary lubrication films. This dramatic friction reduction eliminates the excessive heat generation, wear, and shuddering caused by high friction coefficients in CVT metal-to-metal contact, while maintaining sufficient friction to prevent belt slippage under load — a critical balance unique to CVT applications where too much friction causes shudder but too little causes slippage. Immediate Anti-Shudder Protection Eliminates the annoying and damaging shudder vibration that plagues CVTs, typically felt during light acceleration between 40-60 km/h or when the transmission is under moderate load. The anti-shudder compounds work within minutes of treatment addition to break the stick-slip friction cycle causing vibration, restoring the smooth, seamless power delivery that makes CVTs desirable but is often lost as transmissions age and fluid degrades. CVT Life Extension and Preventative Protection Significantly extends CVT transmission life by protecting belt and pulley contact surfaces from the wear that gradually destroys CVT components, reducing the rate of fluid degradation that accelerates wear, and maintaining hydraulic system cleanliness that ensures proper pressure control. Regular treatment prevents the gradual performance degradation that makes CVTs feel hesitant, jerky, or unresponsive, while avoiding the catastrophic failures requiring complete transmission replacement at costs often exceeding $5,000-$8,000. 10% or Greater Fuel Economy Improvement Delivers measurable fuel consumption savings of 10% or more through reduced friction losses that convert more engine power into vehicle motion rather than wasting energy as heat. The optimized friction management improves CVT efficiency particularly during highway cruising and moderate acceleration where CVTs operate most frequently, translating improved mechanical efficiency directly into reduced fuel costs and lower carbon emissions. Suitable for Push Belt and Chain CVT Types Works effectively in both push belt CVT designs (using metal push belt assemblies) common in most passenger vehicles, and chain-type CVT designs (using metal link chains) found in some high-torque applications. The universal CVT compatibility eliminates confusion about product selection and ensures proper protection regardless of specific CVT design, making it suitable for virtually all CVT-equipped vehicles from compact cars through SUVs. Torque Capacity Enhancement Boosts transmission torque capacity by optimizing friction characteristics at belt/pulley interfaces, allowing the CVT to transfer higher engine power outputs without belt slippage or premature wear. This increased capacity is particularly valuable for vehicles used in demanding applications including towing, mountain driving, or spirited acceleration where stock CVT performance often feels marginal and belt slippage becomes noticeable. Wear and Corrosion Protection Protects critical CVT components including steel belt/chain elements, pulley contact surfaces, bearings, hydraulic control valves, and seals from the wear and corrosion that occurs in the harsh CVT operating environment. The anti-wear additives provide boundary lubrication protection during extreme pressure contact, while corrosion inhibitors prevent moisture-related rust formation that damages precision components and causes hydraulic control issues. Patented Anti-Foaming Technology Contains patented anti-foaming agents specifically formulated for CVT applications where fluid aeration creates serious problems including pump cavitation, reduced hydraulic pressure for pulley clamping, and foam that prevents proper belt lubrication causing slippage. The anti-foam chemistry collapses air bubbles and prevents foam formation, ensuring gears and transmission components always receive optimal fluid lubrication without the air entrainment that degrades performance. Emission Reduction Benefits Reduces exhaust emissions by improving combustion efficiency through better transmission efficiency that reduces engine load, and by enabling the CVT to maintain engine operation in optimal RPM ranges more effectively. The improved transmission operation helps vehicles meet emission standards while delivering the environmental benefits CVT technology promises but requires proper maintenance to achieve. Prevents Expensive CVT Replacement Provides a cost-effective preventative maintenance solution that costs a fraction of CVT replacement (often $5,000-$8,000+ including labor), avoiding the catastrophic belt failure, pulley wear, or hydraulic system damage that destroys CVTs and leaves vehicles stranded. Regular treatment maintains CVT health preventing the gradual degradation that progresses to complete failure, protecting your investment in one of the most expensive components in modern vehicles. NASA Space Technology Heritage Developed using lubrication technology trusted by NASA for over 25 years in aerospace applications and inducted into the NASA Space Technology Hall of Fame for proven performance in extreme conditions. This prestigious recognition validates the treatment's effectiveness through rigorous testing and real-world application in environments where failure is not acceptable, providing confidence the product delivers genuine benefits rather than marketing claims. Superior Performance Over Typical CVT Additives Outperforms typical CVT transmission additives through advanced chemistry specifically formulated for CVT applications rather than adapted from conventional automatic transmission treatments. The CVT-specific formulation addresses the unique challenges of belt/chain CVTs including extreme contact pressures, shudder issues, and thermal loads that conventional transmission additives aren't designed to handle. Technical Specifications Specification Details Part Number BT-ADD-35-033 Product Type CVT Transmission Treatment & Recovery Additive Volume 180ml Treatment Ratio One Bottle per CVT Transmission Fluid Change (Typical) CVT Type Compatibility Push Belt & Chain CVT Designs Friction Reduction Up to 90% Fuel Economy Improvement 10% or Greater Working Time Within Minutes of Addition Active Ingredients Friction Modifiers, Anti-Shudder Compounds, Anti-Wear Additives, Anti-Foam Agents Application Method Add to CVT Transmission Fluid During Service Treatment Frequency Every CVT Fluid Change (30,000-60,000 km Typical) Torque Capacity Enhancement Yes Anti-Shudder Protection Immediate Wear Protection Extreme Pressure Lubrication Corrosion Protection Yes Patent Technology Patented Anti-Foaming Agent Heritage NASA Space Technology Hall of Fame Storage Life Several Years (Store in Cool, Dry Location) Suitable Vehicles All CVT-Equipped Passenger Vehicles, SUVs, Light Trucks Frequently Asked Questions How do I add this treatment to my CVT transmission? The BAINTECH CVT Treatment is typically added during a CVT fluid service when fluid is drained and replaced. Add the entire 180ml bottle to the new CVT fluid during refilling, following your vehicle manufacturer's specified fluid capacity and service procedures. Some experienced DIYers add treatment through the transmission dipstick tube if accessible, though professional installation during scheduled service is recommended to ensure correct fluid levels and proper mixing. Will this fix severe CVT shuddering or is my transmission too far gone? The treatment is remarkably effective at eliminating mild to moderate CVT shudder caused by fluid degradation and friction issues. Many users report complete shudder elimination within 50-200 kilometres of treatment. However, if shudder is caused by mechanical damage (worn belt, damaged pulleys, hydraulic system failure), treatment alone cannot repair physical damage — though it can prevent further deterioration. For severe shudder, add treatment first as a diagnostic step before committing to expensive transmission replacement. Is this compatible with my vehicle manufacturer's CVT fluid or do I need special fluid? The BAINTECH treatment is designed to work as an additive to your vehicle manufacturer's specified CVT fluid, not as a replacement. Always use the correct OEM-specified CVT fluid for your vehicle (Nissan NS-2/NS-3, Honda HCF-2, Toyota CVT-FE, Subaru High Torque CVT Fluid, etc.) and add this treatment as a performance enhancer. Never substitute incorrect CVT fluids as CVT designs are fluid-specific and using wrong fluid causes damage even with treatment added. How often should I use this treatment and when should I start? For preventative maintenance, add treatment every time you change CVT fluid (typically every 30,000-60,000 kilometres depending on manufacturer recommendations and driving conditions). For vehicles experiencing shudder or reduced performance, treatment can be added immediately without waiting for scheduled service. Earlier treatment provides better preventative protection — don't wait until shudder develops before treating, as prevention is always better than correction. Can this treatment damage my CVT or void my warranty? BAINTECH CVT Treatment is formulated to work safely with CVT transmissions and contains no harsh chemicals that damage seals, belts, or components. However, always verify your vehicle warranty terms regarding aftermarket additives. Some manufacturers may claim warranty issues if non-approved additives are used, though proving causation is difficult. For vehicles under warranty, consult your dealer before adding any transmission treatments to avoid potential warranty disputes. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Portable AC power and USB charging from your vehicle's 12V system The Baintech BT150INV is a 150W power inverter that converts 12V DC battery power to 240V AC household power, enabling operation of small appliances and electronics from vehicle electrical systems. This compact inverter outputs standard Australian 240V / 50Hz power suitable for laptop chargers, camera batteries, small power tools, and personal electronics while simultaneously providing three fast-charging USB ports delivering 5V at up to 5A combined output for phones and tablets. The 105 × 80 × 30 mm footprint allows installation in vehicle cabins, centre consoles, or storage areas where space is limited, making it practical for weekend camping, work vehicles, or emergency backup power from auxiliary battery systems. Key Specifications Power output: 150W continuous Input voltage: 12V DC Output voltage: 240V AC Output frequency: 50Hz (Australian standard) USB ports: 3 ports USB output: 5V / 5A combined Dimensions: 105 mm × 80 mm × 30 mm (L × W × H) Model: BT150INV Features & Benefits 150W Continuous Power Output — Run small appliances including laptop chargers, camera battery chargers, drone chargers, electric shavers, and compact power tools directly from your vehicle's 12V system without requiring mains power access at campsites or remote work locations. 240V / 50Hz Australian Standard Output — Delivers household-compatible AC power matching Australian electrical standards, ensuring safe operation of Australian-market appliances and eliminating compatibility concerns with imported electronics designed for different frequencies. 12V DC Input from Vehicle Battery — Connect directly to vehicle auxiliary batteries, dual battery systems, or 12V power outlets to access portable AC power during touring, camping, or work applications where grid power is unavailable. Three Fast-Charging USB Ports — Simultaneously charge multiple smartphones, tablets, or USB-powered devices at 5V with up to 5A combined current output, reducing the need for multiple charging adapters in vehicles with limited power outlets. Compact 105 × 80 × 30 mm Design — Install in tight spaces including centre consoles, under seats, or glove compartments where larger inverters cannot fit, maximizing usable storage space in compact 4WDs, utes, and work vehicles. Smartphone to Small Power Tool Versatility — Support diverse applications from charging personal electronics during daily commutes to powering small tools at remote worksites, providing flexibility for both recreational and professional vehicle users. Portable Emergency Power Solution — Maintain connectivity and device charging during power outages or roadside emergencies by converting vehicle battery power to household AC power for essential communications and lighting equipment. Technical Specs Continuous power rating: 150W Input voltage: 12V DC Input source: Vehicle battery or 12V power system Output voltage: 240V AC Output frequency: 50Hz Output waveform: Not specified Number of AC outlets: Not specified USB charging ports: 3 USB output voltage: 5V USB output current: 5A combined (shared across 3 ports) Physical dimensions: 105 mm length × 80 mm width × 30 mm height Connection method: Not specified (likely 12V plug or hardwire) Protection features: Not specified Applications: Laptops, camera chargers, drone chargers, toy chargers, shavers, small power tools, smartphones, tablets Frequently Asked Questions What appliances can I run on 150W? Small electronics including laptop chargers, camera battery chargers, drone chargers, electric shavers, phone chargers, and compact power tools with power consumption under 150W continuous draw. Can I charge laptops and USB devices simultaneously? Yes, the inverter provides both 240V AC output for laptop chargers and three separate 5V USB ports for simultaneous phone and tablet charging. How do I connect this to my vehicle battery? Connection method not specified in product information; verify whether this unit uses a 12V cigarette lighter plug or requires hardwiring to battery terminals. What is the USB charging current per port? The three USB ports share 5A combined output; individual port current distribution not specified, likely dynamic based on connected device requirements. Does this provide pure sine wave or modified sine wave output? Waveform type not specified; contact manufacturer to confirm compatibility with sensitive electronics requiring pure sine wave power. Compatible With 12V auxiliary battery systems Dual battery setups in 4WDs and utes Vehicle 12V accessory outlets Portable power stations Laptop and notebook computers Camera battery chargers (DSLR, mirrorless, action cameras) Drone battery chargers and controllers Smartphone and tablet charging cables Electric shavers and grooming tools Small power tools (drills, impact drivers under 150W) LED camping lights with AC adapters Portable fans and cooling devices Emergency communication equipment Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Fast, safe, and reliable lithium charging for your 4WD, caravan, or marine setup. Product Overview The Baintech BTCH10A is a purpose-built 10 amp AC-DC charger designed specifically for 12V LiFePO4 lithium batteries. This charger delivers efficient, safe charging for modern lithium setups commonly found in touring vehicles, caravans, camper trailers, and marine applications. Engineered to work with LiFePO4 chemistry, it ensures proper voltage profiles and charging cycles that protect your investment and maximize battery lifespan. The BTCH10A comes ready to connect with a pre-fitted grey Anderson plug, making integration with existing Anderson-based power systems quick and straightforward. Whether you're topping up at camp or maintaining batteries between trips, this charger handles the job with precision. Suitable for portable power systems, auxiliary battery setups, and off-grid touring applications where reliable lithium charging is non-negotiable. Key Specifications 12V DC output optimised for LiFePO4 lithium batteries 10 amp charging current for efficient charge times AC-DC operation from mains power supply Pre-fitted grey Anderson connector for plug-and-play installation Designed for 12 volt applications only Compatible with LiFePO4 battery chemistry Features & Benefits Lithium-Specific Charging Profile: Engineered for LiFePO4 chemistry, this charger delivers the correct voltage and current stages to safely charge lithium batteries without the risk of overcharging or undercharging that can occur with generic lead-acid chargers. Critical for maintaining battery health on extended touring trips. 10 Amp Fast Charging: The 10A output provides a practical balance between charge speed and battery care. For a typical 100Ah LiFePO4 battery, expect meaningful charge recovery within a few hours, making it ideal for overnight camps or quick top-ups at powered sites. Anderson Plug Ready: The pre-fitted grey Anderson connector eliminates wiring hassles and integrates seamlessly with Anderson-based 12V systems. Perfect for caravanners and 4WD tourers who've standardised on Anderson connections throughout their setup. Compact AC-DC Design: Runs directly from 240V mains power, making it ideal for powered caravan sites, home garages, or anywhere you have access to standard household power. No need for bulky external transformers or adaptors. Reliable Baintech Engineering: Built by Baintech, a trusted name in Australian 12V power solutions. Designed to handle the heat, dust, and vibration common to outback touring and off-road applications. Technical Specs Input: 240V AC mains power Output: 12V DC Charging current: 10A Battery chemistry: LiFePO4 (Lithium Iron Phosphate) Connector type: Grey Anderson plug (pre-fitted) Application: 12 volt systems only Compatible With / Goes Well With 12V LiFePO4 lithium batteries (100Ah–200Ah typical range) Anderson plug-based 12V power distribution systems Caravan and camper trailer auxiliary battery setups 4WD dual battery systems using lithium Portable power stations with LiFePO4 cells Marine battery banks (12V lithium only) Note: Verify your battery chemistry before use. This charger is designed exclusively for LiFePO4 batteries. Frequently Asked Questions Will this charger work with AGM or lead-acid batteries?  No, the BTCH10A is designed specifically for LiFePO4 lithium batteries and uses a charging profile optimised for lithium chemistry.  How long does it take to charge a 100Ah lithium battery? Charging time depends on the battery's state of charge.  Can I leave this charger connected long-term? Check the charger's specific charge termination behaviour.  Does the Anderson plug fit standard grey Anderson connectors?  Yes, the pre-fitted grey Anderson plug is compatible with standard 50A Anderson connections commonly used in 12V touring setups. Ensure polarity is correct before connecting. Is this suitable for marine battery systems?  Yes, provided your marine battery is 12V LiFePO4 chemistry. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Clean, stable 240V AC power for tools, appliances, and sensitive electronics—anywhere you've got 12V battery power. Product Overview The Baintech BTPS3000W is a 3000 watt pure sine wave inverter designed to deliver manufacturer-specification power quality for demanding equipment. Unlike modified sine wave inverters that produce choppy waveforms, this unit generates smooth, grid-quality 240V AC power that runs motors cooler, starts equipment more reliably, and keeps sensitive electronics like laptops, medical devices, and digital equipment operating without interference or damage. Built for serious off-grid applications including workshops, remote worksites, caravans, and expedition vehicles, the BTPS3000W handles everything from power tools and air compressors to microwaves and coffee machines. The pure sine wave output is essential for equipment with variable speed motors, laser printers, audio systems, and any device with microprocessor controls that can be damaged or malfunction on modified sine wave power. The inverter features convenient front-panel controls with LED fault indicators, dual USB charging ports for phones and tablets, and optional remote control capability for mounting the switch in accessible locations. At 8.2kg, it's substantial but manageable for permanent installations in canopies, caravans, or marine applications where reliable 240V power is non-negotiable. Key Specifications Continuous power output: 3000W pure sine wave Output voltage: 240V AC, 50Hz (Australian standard) Input voltage: 12V DC nominal USB ports: 2 x 5V, 2.1A for device charging Remote control: Optional remote ON/OFF switch port Front panel controls: Power ON/OFF switch with LED indicators Weight: 8.2kg Cooling: Forced ventilation with heat dissipation vents Protection: Fault indicator LED for diagnostics Grounding: Chassis ground terminal for safety AC output: Standard Australian power receptacles Features & Benefits Pure Sine Wave Output for Equipment Protection: Generates clean, grid-quality power that matches household electricity. Critical for running variable speed tools, digital clocks, audio equipment, medical devices, and any electronics with sensitive microprocessors. Prevents the buzzing, overheating, and premature failure that modified sine wave inverters cause in motorized loads. 3000W Continuous Power Capacity: Handles substantial loads including circular saws, angle grinders, air compressors, microwaves, kettles, and multiple appliances simultaneously. Suitable for running a full camp kitchen setup or powering a remote workshop where mains power isn't available. Peak surge capacity handles motor starting loads. Dual USB Charging Ports: Two 5V, 2.1A USB ports provide convenient phone and tablet charging without needing separate USB adaptors or wasting 240V output on small devices. Handy for keeping communication devices charged while running larger appliances. Remote Control Capability: Optional remote switch port allows you to mount a remote ON/OFF switch in convenient locations—inside the cabin, at the camp kitchen, or wherever makes sense for your setup. No need to access the inverter directly to power up equipment. Front Panel LED Diagnostics: Fault indicator LED turns red when issues arise, helping diagnose problems with input voltage, overload conditions, or thermal shutdown. Inverter indicator shows when equipment is receiving inverted AC power. Simple, at-a-glance status monitoring. Thermal Management System: Forced ventilation with strategically placed vents maintains optimal operating temperature even under sustained high loads. Essential for Australian conditions where ambient temperatures can exceed 40°C and inverters are often installed in enclosed spaces. Hardwired Terminal Options: For high-current applications, hardwire terminal block accommodates permanent installation without relying on standard plug connections. Suitable for fixed caravan installations or workshop setups where the inverter remains permanently mounted. Chassis Grounding for Safety: Ground terminal ensures proper electrical safety grounding to vehicle chassis or earth ground, protecting users from shock hazards and reducing electrical noise interference with radios and other sensitive equipment. Technical Specs Continuous output power: 3000W Peak surge power: Not specified (typically 2x continuous for brief periods) Output waveform: Pure sine wave Output voltage: 240V AC ±10% Output frequency: 50Hz Input voltage: 12V DC nominal (typical range 10.5V–15V) No-load current draw: Not specified Efficiency: Typically 85–90% at rated load USB output: 2 ports, 5V DC, 2.1A per port Protection features: Over-voltage, under-voltage, overload, over-temperature, short-circuit LED indicators: Fault (red), Inverter operation (green/continuous) Cooling: Forced air ventilation Operating temperature: Not specified (confirm spec sheet) Storage temperature: Not specified Dimensions: Not specified Weight: 8.2kg Mounting: Not specified (confirm mounting orientation requirements) Terminals: AC output receptacles + optional hardwire terminal block Remote control port: Yes (optional remote switch, cable not included) Warranty: Refer to Baintech warranty documentation Compatible With / Goes Well With 12V lithium or AGM battery banks (200Ah–400Ah recommended for sustained use) Heavy-gauge DC cabling (35mm²–70mm² depending on cable run length) Anderson plugs or hardwired terminal connections for high-current DC input Inline fuses or circuit breakers rated for 250A+ at 12V Remote ON/OFF switch (optional, sold separately) Battery monitoring systems for tracking state of charge during inverter use Pure sine wave compatible appliances, tools, and electronics Portable power stations and off-grid solar systems 4WD and caravan auxiliary power systems Marine battery systems for running household appliances Caution: Ensure your battery bank and cabling are appropriately sized for high-current draw. Inadequate sizing can result in voltage drop, overheating, and fire risk. Frequently Asked Questions What's the difference between a pure sine wave and a modified sine wave?  Pure sine wave produces smooth, grid-quality power identical to household electricity, suitable for all equipment. What size battery and cabling do I need for 3000W? At 3000W output, the inverter draws approximately 250A from your 12V battery under full load. Can I run my caravan air conditioner on this inverter? Check your air conditioner's starting surge requirements and running wattage. How long will my battery last running 3000W? Battery runtime depends on your battery capacity and load.  Does this inverter need ventilation when installed? Yes, the inverter generates significant heat under load and requires adequate ventilation for cooling.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Lightweight, high-efficiency flexible solar—freedom to go further off-grid without the weight penalty. Product Overview The Baintech BSMARTFLEXI150 is a 150 watt flexible solar panel built around premium SUNPOWER monocrystalline cells delivering 20.5–23.5% efficiency. This isn't your standard flexible panel—the SUNPOWER cell technology extracts more power from available sunlight, maintaining stronger output even in cloudy conditions or low-light situations where cheaper panels fall short. At just 3.3kg and only 3mm thick, this flexi panel replaces bulky glass panels that add weight and create wind resistance on roof-mounted installations. Perfect for caravans, camper trailers, boats, and 4WD canopies where every kilogram counts and aerodynamic profile matters. The flexible design conforms to curved surfaces like caravan roofs or boat decks, and the slimline profile reduces wind noise and drag compared to traditional framed panels. Designed for DIY installation or professional fitment, the flexi panel bonds directly to clean surfaces using appropriate adhesive, eliminating the need for heavy mounting frames and rails. Ideal for tourers who want to extend off-grid capability without permanent sites or generator noise, giving you the freedom to stay longer at remote camps while keeping batteries charged. Key Specifications Power output: 150W nominal Solar cell technology: SUNPOWER monocrystalline Efficiency: 20.5–23.5% Dimensions: 106cm × 53.6cm × 0.3cm (3mm thickness) Weight: 3.3kg Design: Flexible, semi-rigid construction Surface type: Slimline, aerodynamic profile Application: Caravan, 4WD, marine, camper trailer roof mounting Installation: Adhesive bonding to clean surfaces Features & Benefits SUNPOWER High-Efficiency Cells: SUNPOWER monocrystalline technology delivers 20.5–23.5% efficiency, significantly higher than standard flexi panels that typically achieve 15–18%. This means more power generation from the same roof space, critical when mounting area is limited on caravan or canopy roofs. The high efficiency also maintains better output in overcast conditions or during shoulder season touring when sun angles are lower. Ultra-Lightweight at 3.3kg: Weighs a fraction of equivalent glass panels that can exceed 10–12kg. This weight saving matters for caravans operating near maximum towing capacity, boats concerned with top-weight distribution, and 4WDs carrying gear on roof racks. Three of these panels weigh less than one traditional framed panel. Slimline 3mm Aerodynamic Profile: The barely-there 3mm thickness creates minimal wind resistance and virtually eliminates the wind noise associated with traditional raised solar panel mounting. Reduces fuel consumption impact from roof-mounted solar and looks cleaner than bulky frames. Less likely to catch low-hanging branches on tight bush tracks. Flexible Design for Curved Surfaces: Semi-rigid construction allows the panel to conform to gently curved surfaces like caravan roofs, boat decks, or canopy tops. This flexibility also provides some resilience against minor impacts from branches or camping gear, though the panel should still be treated with care. Direct Adhesive Installation: Bonds directly to clean, prepared surfaces using appropriate marine-grade adhesive (not included). Eliminates the weight and complexity of mounting frames, brackets, and rails. Faster installation for DIYers and cleaner finished appearance. Ensure surface preparation follows manufacturer guidelines for reliable long-term bonding. Performs in Low Light: The SUNPOWER cell technology continues generating useful power in cloudy conditions, early morning, or late afternoon when lower-efficiency panels barely produce. This extends your effective charging window throughout the day, particularly valuable during winter touring or in variable weather conditions. Professional or DIY Installation: Suited to both professional caravan/marine installers and competent DIYers. The lightweight, frameless design simplifies handling and positioning compared to manoeuvring heavy glass panels onto roofs. Just ensure proper surface preparation and appropriate adhesive selection. Technical Specs Rated power output: 150W Cell type: SUNPOWER monocrystalline Cell efficiency: 20.5–23.5% Panel dimensions: 106cm (L) × 53.6cm (W) × 0.3cm (H) Panel weight: 3.3kg Construction: Flexible/semi-rigid Surface profile: Low profile, aerodynamic Mounting method: Adhesive bonding (adhesive not included) Warranty: Refer to Baintech warranty documentation Solar Cell Type: Mono Solar Cell Power Tolerance: +-3% Max.power.(PMX) 150W Voltage at Pmax: (Vmp) 26V Current at Pmax: (Imp) 5.77A Open Circuit Volatge: 307.V Short Circuit Current: 6.23A Maximum Seriex Fuse: 15A Size: 1060 x700 x 3mm Standard Test Condition: AM 1.5 1KW/m2 25C Compatible With / Goes Well With 12V MPPT solar charge controllers (10A–30A rating) 12V PWM solar charge controllers LiFePO4 lithium batteries for off-grid power systems AGM and gel deep-cycle batteries Caravan and camper trailer roof mounting 4WD canopy and roof rack installations Marine deck and cabin top mounting (confirm waterproof rating) MC4 solar cable connectors and extension cables Anderson plug solar connection systems Inline fuses or circuit breakers for solar arrays Marine-grade adhesives (Sikaflex, 3M VHB tape) Cable entry glands for roof penetrations Additional flexi panels for expanded solar capacity Note: Confirm voltage and current specifications from Baintech documentation before selecting solar controller and wiring configuration. Frequently Asked Questions What adhesive should I use to mount this panel?  Use a high-quality marine-grade flexible adhesive like Sikaflex or 3M VHB tape designed for outdoor UV exposure and temperature cycling. Can this panel be walked on?  No. While the flexible construction provides some resilience, these panels are not designed for foot traffic. Will this panel work with my MPPT solar controller? Yes, flexi panels work with standard MPPT or PWM solar controllers. How does this compare to a rigid glass panel? The flexi panel offers weight savings, aerodynamic benefits, and curved-surface mounting capability Can I connect multiple flexi panels? Yes, panels can be wired in series, parallel, or series-parallel depending on your system voltage and current requirements. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Professional 12V charging for workshop and touring applications The Baintech BTPB600 is a microprocessor-controlled 12V 40A battery charger engineered for reliable charging of automotive, deep-cycle, and AGM batteries. This single-outlet charger features multi-stage automatic charging technology that optimises charge cycles to extend battery life and prevent overcharging. The adjustable voltage function allows precise tuning for different battery types, while the LED status indicator provides clear visual confirmation of charging progress. Built for Australian workshops, 4WD tourers, and caravan owners who demand dependable charging performance in demanding conditions. Key Specifications Output: 12V DC, 40A maximum charging current Outlets: Single charging outlet Control: Microprocessor-controlled multi-stage automatic charging Voltage adjustment: Adjustable output voltage for battery type optimization Status indication: LED light display for charge status monitoring Warranty: 2-year manufacturer warranty Design: Robust construction for workshop and field use Features & Benefits Multi-Stage Automatic Charging — Intelligent charging profile adapts through bulk, absorption, and float stages to fully charge batteries without damage, ideal for maintaining auxiliary batteries in 4WDs and caravans during storage or between trips. Adjustable Voltage Output — Fine-tune charging voltage to suit flooded, AGM, or gel batteries, ensuring optimal charging for your specific battery chemistry whether you're running a workshop with varied battery types or maintaining a fleet. 40A High-Current Output — Delivers substantial charging power to recover deeply discharged batteries quickly, perfect for workshop environments where turnaround time matters or for rapidly recharging large-capacity house batteries. Microprocessor Control — Advanced charging algorithm monitors battery condition continuously and adjusts charging parameters automatically, preventing overcharging damage during extended charge periods in workshops or storage facilities. LED Status Indicator — Clear visual feedback shows charging status at a glance, eliminating guesswork and allowing you to monitor multiple charging operations across a busy workshop or campsite setup. Technical Specs Input voltage: 240V AC (standard Australian mains) Output voltage: 12V DC (adjustable) Maximum output current: 40A Charging stages: Multi-stage automatic (bulk/absorption/float) Control type: Microprocessor-controlled Status display: LED indicator Outlets: 1 x battery charging outlet Warranty period: 2 years Applications: Automotive, deep-cycle, AGM, workshop, caravan, 4WD Frequently Asked Questions What battery types can this charger handle? The BTPB600 charges 12V flooded, AGM, and gel batteries with adjustable voltage settings to suit each chemistry type. Is this suitable for charging deep-cycle auxiliary batteries? Yes, the 40A output and multi-stage charging make it ideal for deep-cycle batteries commonly used in caravans and 4WD setups. Can I leave batteries connected during long-term storage? The automatic float stage maintains batteries without overcharging, making it suitable for extended connection periods in storage applications. Does this charger require professional installation? The single-outlet design is straightforward for workshop use; connect to 240V mains and attach battery leads following polarity markings. What does the LED indicator show during charging? The LED displays charging status through different stages, indicating when bulk charging is active, absorption phase, or float maintenance mode. Compatible With 12V automotive starter batteries Deep-cycle AGM batteries (auxiliary/house banks) Gel batteries for marine and caravan applications Workshop battery maintenance systems Caravan and 4WD auxiliary battery systems Flooded lead-acid batteries Battery isolators and dual battery systems 12V battery monitoring systems Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Secure, durable battery mounting—keeps your auxiliary battery locked down through corrugations and rough tracks. Product Overview The Baintech BT-TRAY-KIT is a large battery tray designed to securely mount and retain auxiliary batteries in 4WD, caravan, camper trailer, and marine applications. This kit includes both the tray and a heavy-duty hold-down strap, providing a complete mounting solution that prevents battery movement during off-road travel, hard braking, or rough water conditions.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Secure, durable battery mounting for mid-size auxiliaries—keeps your power system locked down on rough tracks. Product Overview The Baintech BT-TRAY-KIT (M) is a purpose-built medium-size mounting solution for mid-size auxiliary batteries in 4WD, caravan, camper trailer, and marine applications. This kit includes both the tray and a heavy-duty hold-down strap, providing everything needed to securely mount and retain batteries through off-road travel, hard braking, or rough water conditions.  Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Organized circuit protection for 4WD and marine electrical systems The Baintech BTFB12R is a 12-way fuse block engineered to consolidate and protect multiple electrical circuits in 4WD, caravan, and marine installations. This fuse distribution panel accepts standard ATO and ATC blade fuses, providing up to 30A protection per individual circuit with a 100A maximum total capacity. The clear poly-carbonate cover meets ABYC/USCG insulation requirements while allowing visual fuse inspection, and the common positive/negative bus bars simplify wiring by eliminating multiple connection points. Built-in spare fuse holders and included circuit labels make this an essential component for organized auxiliary power systems in touring vehicles, camper trailers, and boat electrical installations. Key Specifications Fuse outlets: 12 individual circuits Maximum capacity per fuse block: 100A total Maximum capacity per circuit: 30A individual fuse rating Fuse types accepted: ATO and ATC standard or mini blade fuses (fast acting) Bus bar configuration: Common negative and common positive terminals Cover material: Clear poly-carbonate with ABYC/USCG compliant insulation Base material: Reinforced poly-carbonate construction Spare fuse storage: 2 spare fuse holder positions Circuit identification: Label provision included Features & Benefits 12 Individual Fuse Circuits — Protect and organize up to 12 separate appliances or accessories from a single distribution point, ideal for complex 4WD setups running fridges, lights, pumps, inverters, and communication equipment without tangled wiring. 100A Total Capacity with 30A Per Circuit — Handle substantial total loads while protecting individual circuits appropriately, perfect for caravan installations where multiple high-draw appliances operate simultaneously without overloading any single fuse position. Common Positive and Negative Bus Bars — Simplify installation by connecting power once to shared terminals rather than running individual wires to each circuit, reducing connection points and installation time in tight engine bay or under-seat locations. ATO/ATC Blade Fuse Compatibility — Accept widely available standard and mini blade fuses found at automotive stores across Australia, ensuring you can source replacements anywhere during remote touring or marine expeditions. Clear Poly-Carbonate Cover — Inspect fuse status visually without removing the cover while meeting ABYC/USCG insulation safety standards, essential for marine applications and vehicles exposed to salt spray, dust, and moisture. Reinforced Poly-Carbonate Base — Withstand vibration and impact in off-road environments, providing durable mounting for auxiliary battery systems subject to corrugations, rough tracks, and marine conditions. Integrated Spare Fuse Storage — Keep two spare fuses secured within the block for emergency replacements on remote tracks or offshore, eliminating searches through toolboxes when a fuse fails. Circuit Labeling System — Identify each circuit clearly with included labels, simplifying troubleshooting and preventing confusion when multiple users access the electrical system in shared vehicles or charter boats. Technical Specs Number of fuse positions: 12 Total current capacity: 100A maximum Individual circuit capacity: 30A maximum per fuse Fuse type compatibility: ATO blade fuses (standard size), ATC blade fuses (standard size), mini blade fuses Fuse action type: Fast acting Bus bar design: Common positive rail, common negative rail Cover material: Poly-carbonate (clear) Cover compliance: ABYC/USCG insulation requirements Base material: Reinforced poly-carbonate Spare fuse capacity: 2 positions Circuit labeling: Provision for adhesive or write-on labels Mounting: Base mounting holes for secure installation Applications: 4WD auxiliary systems, caravan electrical, marine electrical, camper trailer, dual battery systems Frequently Asked Questions What size fuses does this block accept? The BTFB12R accepts ATO and ATC standard blade fuses as well as mini blade fuses, all of which are fast-acting types commonly available at automotive retailers. Can I run 12 circuits at 30A simultaneously? No, while each individual circuit supports up to 30A, the total combined load across all circuits must not exceed 100A to prevent overloading the bus bars. Is this suitable for marine environments? Yes, the poly-carbonate cover meets ABYC/USCG insulation requirements and the reinforced construction withstands marine conditions, though additional weatherproofing of connections is recommended. How do I connect power to this fuse block? Connect your positive power source to the common positive bus bar and ground to the common negative bus bar, then wire individual circuits from each fused outlet to your appliances. Does this come with fuses included? Not specified; purchase appropriate ATO or ATC blade fuses separately based on the current requirements of each circuit you're protecting. Compatible With 12V dual battery systems and battery isolators Auxiliary battery installations in 4WDs and caravans Anderson plug power distribution systems LED lighting circuits (interior/exterior) 12V fridge and freezer installations Water pump circuits Inverter power feeds UHF radio and communication equipment Caravan appliance circuits Marine electrical systems Solar charge controller circuits Accessory power outlets and USB chargers Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Secure mounting for compact batteries—ideal for tight spaces and lightweight auxiliary power setups Product Overview The Baintech BT-TRAY-KIT (S) is a purpose-built small-size mounting solution for compact auxiliary batteries in 4WD, caravan, camper trailer, and marine applications. This kit includes both the tray and a heavy-duty hold-down strap, providing everything needed to securely mount and retain smaller batteries through off-road travel, hard braking, or rough water conditions.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Visual circuit protection with LED fault indication for auxiliary systems The Baintech BTFUSEBLOCK6 is a 6-way fuse distribution block featuring red LED indicators that illuminate when individual fuses fail, providing instant visual fault identification. This fuse panel supports 100A input capacity through M5 threaded stud terminals and delivers up to 30A per individual circuit, suitable for organizing auxiliary electrical systems in 4WD vehicles, caravans, and marine applications. The LED fault indication eliminates the need to physically test fuses during troubleshooting, while included circuit labels enable clear identification of each protected appliance. Compact dimensions of 8.5 × 8.5 × 3.5 cm allow installation in confined spaces under dashboards, in engine bays, or behind storage panels. Key Specifications Fuse outlets: 6 individual circuits Input terminal rating: 100A at 32V DC Input terminal type: M5 threaded studs Input wire size: #4-6 AWG Output terminal rating: 30A maximum per circuit Output wire size: #12-16 AWG LED indicators: Red LED illuminates when fuse is broken Circuit identification: Labels included Dimensions: 8.5 cm × 8.5 cm × 3.5 cm Features & Benefits Red LED Fuse Indicators — Individual red LEDs illuminate instantly when a fuse blows, allowing immediate fault identification without removing covers or testing fuses with multimeters, essential for rapid troubleshooting on remote tracks or during night operations. 6 Individual Fused Circuits — Organize and protect up to 6 separate appliances or accessories from a single distribution point, ideal for mid-sized 4WD electrical systems running fridges, lighting circuits, water pumps, and communication equipment without excessive wiring complexity. 100A Input Capacity — Handle substantial total loads through robust M5 threaded stud terminals designed for secure high-current connections, suitable for auxiliary battery systems powering multiple high-draw appliances in touring setups. 30A Per Circuit Protection — Each individual circuit supports up to 30A output, providing appropriate protection for accessories while the total combined load must remain within the 100A input rating. M5 Threaded Stud Input Terminals — Secure main power connections with threaded terminals that resist vibration loosening in off-road environments, eliminating the connection failures common with crimp-only terminals on corrugated tracks. #4-6 AWG Input Wire Compatibility — Accept heavy-gauge wire appropriate for 100A current delivery, ensuring safe power distribution without voltage drop or overheating in high-demand electrical systems. #12-16 AWG Output Wire Compatibility — Standard output wire sizing suits most 12V appliances and accessories, simplifying installation with readily available automotive wire from Australian suppliers. Included Circuit Labels — Identify each protected circuit clearly to simplify system operation and troubleshooting when multiple users access the vehicle or when modifications are made over time. Compact 8.5 × 8.5 × 3.5 cm Footprint — Install in tight spaces under seats, behind panels, or in crowded engine bays where larger fuse blocks cannot fit, maximizing usable storage space in compact 4WD and caravan installations. Technical Specs Number of fuse positions: 6 Input current rating: 100A maximum Input voltage rating: 32V DC Input terminal style: M5 threaded studs Input wire gauge range: #4 AWG to #6 AWG Individual circuit capacity: 30A maximum per fuse Output wire gauge range: #12 AWG to #16 AWG Fault indication: Red LED per circuit (illuminates when fuse is broken) Circuit labeling: Adhesive labels included Physical dimensions: 8.5 cm length × 8.5 cm width × 3.5 cm height Mounting: Base mounting provision Applications: 4WD auxiliary systems, caravan electrical, marine electrical, camper trailer, dual battery systems Frequently Asked Questions What size fuses does this block accept? Not specified in product information; verify fuse type compatibility with manufacturer documentation before purchase. Do the LED indicators stay on when the system is powered? The red LEDs illuminate only when a fuse is broken, not during normal operation, allowing instant identification of failed circuits. Can I run all 6 circuits at 30A simultaneously? No, while each circuit supports up to 30A individually, the total combined load across all circuits must not exceed the 100A input terminal rating. What wire size do I need for the main power input? Use #4 AWG or #6 AWG wire for the input connection to the M5 threaded stud terminals to safely handle the 100A capacity. Does this include fuses and mounting hardware? Not specified; purchase appropriate fuses separately and verify mounting hardware requirements with product packaging or manufacturer documentation. Compatible With 12V dual battery systems and battery isolators Auxiliary battery installations in 4WDs and caravans Anderson plug power distribution systems LED lighting circuits (interior/exterior) 12V fridge and freezer installations Water pump circuits Inverter power feeds UHF radio and communication equipment Caravan appliance circuits Marine electrical systems Solar charge controller circuits Accessory power outlets and USB chargers Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Comprehensive circuit protection with LED fault indication for complex auxiliary systems The Baintech BTFUSEBLOCK12 is a 12-way fuse distribution block featuring red LED indicators that illuminate when individual fuses fail, providing instant visual fault identification across all circuits. This fuse panel supports 100A input capacity through M5 threaded stud terminals and delivers up to 30A per individual circuit, suitable for organizing comprehensive auxiliary electrical systems in 4WD vehicles, caravans, and marine applications. The LED fault indication eliminates the need to physically test fuses during troubleshooting, while included circuit labels enable clear identification of each protected appliance. Dimensions of 14 cm × 8.5 cm × 3.5 cm accommodate installations in under-dash locations, engine bays, or behind storage panels where multiple circuits require consolidated protection. Key Specifications Fuse outlets: 12 individual circuits Input terminal rating: 100A at 32V DC Input terminal type: M5 threaded studs Input wire size: #4-6 AWG Output terminal rating: 30A maximum per circuit Output wire size: #12-16 AWG LED indicators: Red LED illuminates when fuse is broken Circuit identification: Labels included Dimensions: 14 cm × 8.5 cm × 3.5 cm (L × W × H) Features & Benefits Red LED Fuse Indicators — Individual red LEDs illuminate instantly when a fuse blows, allowing immediate fault identification without removing covers or testing fuses with multimeters, essential for rapid troubleshooting on remote tracks or during night operations across multiple circuits. 12 Individual Fused Circuits — Organize and protect up to 12 separate appliances or accessories from a single distribution point, ideal for comprehensive 4WD electrical systems running fridges, multiple lighting circuits, water pumps, inverters, communication equipment, and accessory outlets without excessive wiring complexity. 100A Input Capacity — Handle substantial total loads through robust M5 threaded stud terminals designed for secure high-current connections, suitable for auxiliary battery systems powering multiple high-draw appliances in extended touring setups. 30A Per Circuit Protection — Each individual circuit supports up to 30A output, providing appropriate protection for accessories while the total combined load must remain within the 100A input rating. M5 Threaded Stud Input Terminals — Secure main power connections with threaded terminals that resist vibration loosening in off-road environments, eliminating the connection failures common with crimp-only terminals on corrugated tracks. #4-6 AWG Input Wire Compatibility — Accept heavy-gauge wire appropriate for 100A current delivery, ensuring safe power distribution without voltage drop or overheating in high-demand electrical systems. #12-16 AWG Output Wire Compatibility — Standard output wire sizing suits most 12V appliances and accessories, simplifying installation with readily available automotive wire from Australian suppliers. Included Circuit Labels — Identify each protected circuit clearly to simplify system operation and troubleshooting when multiple users access the vehicle or when modifications are made over time across 12 separate circuits. 14 × 8.5 × 3.5 cm Footprint — Install in accessible locations where multiple circuit management is required, balancing compact design with the capacity to handle complex electrical systems in touring 4WDs and caravans. Technical Specs Number of fuse positions: 12 Input current rating: 100A maximum Input voltage rating: 32V DC Input terminal style: M5 threaded studs Input wire gauge range: #4 AWG to #6 AWG Individual circuit capacity: 30A maximum per fuse Output wire gauge range: #12 AWG to #16 AWG Fault indication: Red LED per circuit (illuminates when fuse is broken) Circuit labeling: Adhesive labels included Physical dimensions: 14 cm length × 8.5 cm width × 3.5 cm height Mounting: Base mounting provision Applications: 4WD auxiliary systems, caravan electrical, marine electrical, camper trailer, dual battery systems Frequently Asked Questions What size fuses does this block accept? Not specified in product information; verify fuse type compatibility with manufacturer documentation before purchase. Do the LED indicators stay on when the system is powered? The red LEDs illuminate only when a fuse is broken, not during normal operation, allowing instant identification of failed circuits among all 12 positions. Can I run all 12 circuits at 30A simultaneously? No, while each circuit supports up to 30A individually, the total combined load across all circuits must not exceed the 100A input terminal rating. What wire size do I need for the main power input? Use #4 AWG or #6 AWG wire for the input connection to the M5 threaded stud terminals to safely handle the 100A capacity. Does this include fuses and mounting hardware? Not specified; purchase appropriate fuses separately and verify mounting hardware requirements with product packaging or manufacturer documentation. Compatible With 12V dual battery systems and battery isolators Auxiliary battery installations in 4WDs and caravans Anderson plug power distribution systems LED lighting circuits (interior/exterior/camp lighting) 12V fridge and freezer installations Water pump circuits Inverter power feeds UHF radio and communication equipment Caravan appliance circuits Marine electrical systems Solar charge controller circuits Accessory power outlets and USB chargers Auxiliary lighting systems Winch power distribution Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less