Victron Energy 360W 12/24-15A Orion-Tr Isolated DC-DC Converter: The DC-DC Converter From Victron Energy Have Been Designed to Be a True World-wide Product Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). Adjustable output voltage: can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) On 12V and 24V input models only Victron Energy ORI122441110 Specifications: Input voltage range: 10-17V Under voltage shut down: 7V Under voltage restart: 7,5V Nominal output voltage: 24,2V Output voltage adjust range: 20-30V Output voltage tolerance: +/- 0,2V Output noise: 2mV rms Cont. output current at nominal output voltage and 25¬∞C: 15A Maximum output current (10 s) at nominal output voltage: 25A Short circuit output current: 40A Cont. output power at 25¬∞C: 430W Cont. output power at 40¬∞C: 360W Efficiency: 88% Off load current: < 100mA Galvanic isolation: 200V dc between input, output and case Operating temperature range: -20 to +55¬∞C (derate 3% per ¬∞C above 40¬∞C) Humidity: Max. 95% non-condensing DC connection: Screw terminals Maximum cable cross-section: 16 mm¬≤ AWG10 Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 100A (1+1) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024100000 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 20 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 100 A Charge current starter batt. (A): 4 Charge algorithm: 7 stage adaptive Battery capacity (Ah): 500-1000 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-TG Battery Charger 24/100 (1+1) 120-240V: The Battery Charger From Victron Energy Have Been Designed to Be a True Worldwide Product Universal 90-265 V AC input voltage range and also suitable for DC supply All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers will also accept a 90-400 V DC supply. Germanischer Lloyd approval The Chargers have been approved by Germanischer Lloyd (GL) to environmental category C, EMC 1. Category C applies to equipment protected from the weather. EMC 1 applies to conducted and radiated emission limits for equipment installed on the bridge of a ship. The approval to GL C, EMC1 implies that the Chargers also complies to IEC 60945-2002, category ‚Äòprotected' and ‚Äòequipment installed on the bridge of a ship'. The GL certification applies to 185-265 V AC supply. Victron Energy SDTG2401003 Features: Microprocessor control Can be used as power supply Battery temperature sensor for temperature compensated charging Battery voltage sensing to compensate for voltage loss due to cable resistance Victron Energy SDTG2401003 Specifications: Input voltage (V AC): 230 Input voltage range (V AC): 90-265 Input voltage range (V DC): 90-400 Frequency (Hz): 45-65 Hz or DC Power factor: 1 Charge voltage 'absorption' (V DC): 28,5 Charge voltage 'float' (V DC): 26,5 Charge current house battery (A): 100 Charge current starter battery (A): 4 Charge characteristic: IUoUo (three step) Battery capacity (Ah): 500-1000 Temperature sensor: Yes Can be used as power supply: Yes Remote alarm: Potential free contacts 60V / 1A (1x NO and 1x NC) Forced cooling: Yes Protection: a, b, c, d Operating temp. range: -40 to +50¬∞C (-40 - 122¬∞F) Full output current up to 40¬∞C Humidity (non-condensing): max 95% Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Phoenix Battery Charger 12/50(2+1) 120-240V: The Battery Charger From Victron Energy Have Been Designed to Be a True Worldwide Product Adaptive 4-stage charge characteristic: bulk – absorption – float – storage The Phoenix Charger features a microprocessor controlled ‚Äòadaptive' battery management system that can be preset to suit different types of batteries. The ‚Äòadaptive' feature will automatically optimise the process relative to the way the battery is being used. The right amount of charge: variable absorption time When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Phoenix Charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‚Äòequalize' the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) The chargers will accept a 90-400 V DC supply. Computer interface Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Victron Energy PCH012050001 Specifications: Input voltage range (V AC): 90-265 Input voltage range (V DC): 90-400 Frequency (Hz): 45-65 Power factor: 1 Charge voltage 'absorption' (V DC): 14,4 Charge voltage 'float' (V DC): 13,8 Storage mode (V DC): 13,2 Charge current house battery (A): 50 Charge current starter battery: 4 Charge characteristic: 4 stage adaptive Battery capacity (Ah): 200-800 Temperature sensor: Yes Can be used as power supply: Yes Forced cooling: Yes Protection: a,b,c,d Operating temp. range: -20 to 60¬∞C (0 - 140¬∞F) Humidity (non-condensing): max 95% Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Phoenix Battery Charger 12/30(2+1) 120-240V: The Battery Charger From Victron Energy Have Been Designed to Be a True Worldwide Product Adaptive 4-stage charge characteristic: bulk – absorption – float – storage The Phoenix Charger features a microprocessor controlled ‚Äòadaptive' battery management system that can be preset to suit different types of batteries. The ‚Äòadaptive' feature will automatically optimise the process relative to the way the battery is being used. The right amount of charge: variable absorption time When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Phoenix Charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‚Äòequalize' the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) The chargers will accept a 90-400 V DC supply. Computer interface Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Victron Energy PCH012030001 Specifications: Input voltage range (V AC): 90-265 Input voltage range (V DC): 90-400 Frequency (Hz): 45-65 Power factor: 1 Charge voltage 'absorption' (V DC): 14,4 Charge voltage 'float' (V DC): 13,8 Storage mode (V DC): 13,2 Charge current house battery (A): 30 Charge current starter battery: 4 Charge characteristic: 4 stage adaptive Battery capacity (Ah): 100-400 Temperature sensor: Yes Can be used as power supply: Yes Forced cooling: Yes Protection: a,b,c,d Operating temp. range: -20 to 60¬∞C (0 - 140¬∞F) Humidity (non-condensing): max 95% Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy 24V 16A 3C Centaur Battery Charger: The Centaur Range of Battery Chargers from Victron Energy Have Been Designed to Be a True World-Wide Product Designed to meet the requirements of both CE for Europe and UL for the United States, the Centaur model range features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike other products that state universal input, the Centaur range will maintain full output power within the entire specified range. The Centaur model will also work on 90-400VDC input, making it a perfect Charging DC-DC Converter in a Diesel Electric system.Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A.The fact that the same product is suitable for any boat, regardless of the intended market or where the boat will be taken, is a great advantage to the boat builder and the boat owner in equal measure.Conscious of the price sensitivity in this competitive market, a single model range for all markets also means more competitive costs. Without compromising Victron Energy brand qualities this range is comprehensive, competitive and compatible wherever in the world they might be used.Victron Energy CCH024016000 Specifications: Dimensions: (L x W x H): 355 x 215 x 110mm Part Number: CC24/16 Charging Current: 16A Type Of Charger: 3 step battery charger Insulation: IP21 Type Of Battery: Flooded Lead-acid, Gel-Cell or AGM Battery Capacity: 45-150Ah Charging Voltage: 28.5 V DC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy 12V 60A 3C Centaur Battery Charger: The Centaur Range of Battery Chargers from Victron Energy Have Been Designed to Be a True World-Wide Product Designed to meet the requirements of both CE for Europe and UL for the United States, the Centaur model range features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike other products that state universal input, the Centaur range will maintain full output power within the entire specified range. The Centaur model will also work on 90-400VDC input, making it a perfect Charging DC-DC Converter in a Diesel Electric system.Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A.The fact that the same product is suitable for any boat, regardless of the intended market or where the boat will be taken, is a great advantage to the boat builder and the boat owner in equal measure.Conscious of the price sensitivity in this competitive market, a single model range for all markets also means more competitive costs. Without compromising Victron Energy brand qualities this range is comprehensive, competitive and compatible wherever in the world they might be used.Victron Energy CCH012060000 Specifications: Dimensions: (L x W x H): 426 x 239 x 135mm Part Number: CC12/60 Charging Current: 60A Type Of Charger: 3 step battery charger Insulation: IP21 Type Of Battery: Flooded Lead-acid, Gel-Cell or AGM Battery Capacity: 240-600Ah Charging Voltage: 14.3 V DC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy 12V 50A 3C Centaur Battery Charger: The Centaur Range of Battery Chargers from Victron Energy Have Been Designed to Be a True World-Wide Product Designed to meet the requirements of both CE for Europe and UL for the United States, the Centaur model range features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike other products that state universal input, the Centaur range will maintain full output power within the entire specified range. The Centaur model will also work on 90-400VDC input, making it a perfect Charging DC-DC Converter in a Diesel Electric system.Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A.The fact that the same product is suitable for any boat, regardless of the intended market or where the boat will be taken, is a great advantage to the boat builder and the boat owner in equal measure.Conscious of the price sensitivity in this competitive market, a single model range for all markets also means more competitive costs. Without compromising Victron Energy brand qualities this range is comprehensive, competitive and compatible wherever in the world they might be used.Victron Energy CCH012050000 Specifications: Dimensions: (L x W x H): 426 x 239 x 135mm Part Number: CC12/50 Charging Current: 50A Type Of Charger: 3 step battery charger Insulation: IP21 Type Of Battery: Flooded Lead-acid, Gel-Cell or AGM Battery Capacity: 500Ah Charging Voltage: 14.3 V DC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Centaur Battery Charger 12V 40A 3C: The Centaur Range of Battery Chargers from Victron Energy Have Been Designed to Be a True World-Wide Product Designed to meet the requirements of both CE for Europe and UL for the United States, the Centaur model range features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike other products that state universal input, the Centaur range will maintain full output power within the entire specified range. The Centaur model will also work on 90-400VDC input, making it a perfect Charging DC-DC Converter in a Diesel Electric system.Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A.The fact that the same product is suitable for any boat, regardless of the intended market or where the boat will be taken, is a great advantage to the boat builder and the boat owner in equal measure.Conscious of the price sensitivity in this competitive market, a single model range for all markets also means more competitive costs. Without compromising Victron Energy brand qualities this range is comprehensive, competitive and compatible wherever in the world they might be used.Victron Energy CCH012040000 Specifications: Dimensions: (L x W x H) 426 x 239 x 135mm Part Number: CC12/40 Charging Current: 40A Type Of Charger: 3 step battery charger Insulation: IP21 Type Of Battery: Flooded Lead-acid, Gel-Cell or AGM Battery Capacity: 160-400Ah Charging Voltage: 14.3 V DC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less