8000 Series 2-Channel Triple Shielded RCA 17ft, Oversized Silver-Plated Copper, Triple-Braided + Mylar Shielding, Locking Split-Tip Connectors, 3 Conductors per Channel, C3 Tech. Product Overview The Stinger SI8217 is a 17-foot (5-metre) 2-channel audiophile-grade RCA interconnect from the 8000 Series engineered for installations where signal quality is the priority and the routing distance demands a longer run. At 17 feet, the SI8217 covers the full head-unit-to-boot-amplifier run in most vehicles including SUVs, wagons, and vans, with cable to spare for routing around obstacles, through door sills, and along body creases. Oversized silver-plated copper conductors use three conductors per channel separate positive, negative, and signal drain paths ensuring true channel separation and a low-impedance signal return across the full 5-metre length. Triple-braided shielding combined with an inner Mylar foil layer provides multi-directional noise rejection critical over a longer cable run where interference exposure is greatest. A directional high-rate double twisted-pair construction adds a further architectural layer of noise cancellation. Precision machined pewter-finish locking metal ends with channel identification, locking split-tip connectors, no solder joints, moulded strain reliefs, and C3 Tech (Continuous Connection Construction) complete the build. Key Specifications SKU: SI8217 Series: 8000 Series Channels: 2 Length: 17 feet (5 metres) Conductor: Oversized silver-plated copper Conductors per channel: 3 (positive, negative, signal drain) Total conductors: 6 Construction: Directional high-rate double twisted-pair Shielding: Triple-braided + Mylar foil Connector type: Locking split-tip RCA Connector finish: Pewter Connector end: Precision machined locking metal with channel ID Solder joints: None Strain relief: Moulded Outer jacket: Black mesh protective Construction method: C3 Tech (Continuous Connection Construction) Warranty: Not specified — confirm with Stinger Features & Benefits 17-Foot Length — Full Vehicle Run for Larger Vehicles At 17 feet (5 metres), the SI8217 provides sufficient length for boot-mounted amplifier installations in SUVs, wagons, and vans where a 12-foot cable falls short. The additional length allows for clean routing along the full B-pillar-to-boot path, with slack to avoid tight bends at cable entry points. Oversized Silver-Plated Copper Conductors Oversized silver-plated copper combines the high-frequency precision of silver with the current-carrying capacity of copper — delivering tight, controlled bass response and crystal-clear high-frequency detail across the full 20Hz–20kHz audio spectrum and beyond. Over a 17-foot run, conductor quality has a measurably greater impact on signal integrity than over a short run. Triple-Braided + Mylar Shielding — Critical Over Long Runs A 17-foot cable has significantly more exposure to electromagnetic interference than a 6-foot cable — passing along a greater portion of the vehicle's wiring, alternator, and ignition interference sources. Three independent braided layers cascade over each other, with each covering any gaps in the layer beneath, combined with an inner Mylar foil layer for multi-directional noise rejection from both radiated and conducted sources. Three Conductors per Channel — True Channel Separation Dedicated positive, negative, and signal drain conductors per channel separate the shield drain from the audio signal return — eliminating the noise interaction that occurs when these paths share a single conductor in a standard two-conductor design. Directional High-Rate Double Twisted-Pair Construction The directional double twisted-pair winding is orientated to maximise noise cancellation when signal flows from source unit to amplifier. Directional markings indicate correct orientation. The architectural noise cancellation of the twisted-pair geometry is particularly effective over longer cable runs. C3 Tech — No Breaks Over the Full 17 Feet Stinger's C3 (Continuous Connection Construction) ensures no breaks, solder joints, or resistance discontinuities throughout the entire 17-foot length — providing consistent signal transfer from end to end. Locking Split-Tip Connectors + Pewter Precision Machined Ends Spring-tension locking split-tip connectors resist vibration-induced loosening in the automotive environment. Pewter-finished precision machined metal ends with channel identification markings ensure correct left/right routing and corrosion-resistant contact at both ends. Technical Specs Specification Detail Brand Stinger SKU SI8217 Series 8000 Series Channels 2 Length 17 feet (5 metres) Conductor Oversized Silver-Plated Copper Conductors per Channel 3 (positive, negative, signal drain) Total Conductors 6 Construction Directional High-Rate Double Twisted-Pair Shielding Triple-Braided + Mylar Foil Connector Type Locking Split-Tip RCA Connector Finish Pewter Connector Ends Precision Machined Locking Metal, Channel ID Solder Joints None Strain Relief Moulded Outer Jacket Black Mesh Protective Construction Method C3 Tech Warranty Not confirmed — confirm with Stinger Compatible With / Goes Well With Suitable for: 2-channel amplifier and subwoofer monoblock installations in larger vehicles where the full routing distance from head unit to boot-mounted amplifier exceeds 12 feet SUVs, wagons, vans, and larger utes where additional cable length is needed to clear obstacles in the routing path High-performance amplifier installations where signal cable quality must match the amplifier's capability Pairs well with: Rockford Fosgate, Hertz, Morel, and AudioControl amplifiers Stinger SI82YF and SI82YM 8000 Series Y-adapters for consistent system build across all RCA connections Stinger SI8212 (12ft / 3.7m) for shorter vehicle runs in the same 8000 Series specification Length selection guide: SI826 (6ft / 1.8m) — amplifier in close proximity to head unit. SI8212 (12ft / 3.7m) — standard boot-mounted installation in compact to mid-size vehicles. SI8217 (17ft / 5m) — larger vehicles and longer routing paths. Frequently Asked Questions What is the difference between the SI8217 and the SI8212? Both are identical in specification, construction, and performance — same 8000 Series triple-braided shielding, silver-plated conductors, locking connectors, and C3 Tech. The only difference is length: SI8217 is 17 feet (5m) for larger vehicles, SI8212 is 12 feet (3.7m) for compact to mid-size vehicles. Select based on your vehicle's measured routing distance. What does triple-braided shielding provide that a standard single braid does not? Three independent braided layers cascade over each other — each covering any gaps in the layer beneath — achieving dramatically higher total shield coverage than a single braid. Combined with the inner Mylar foil layer, the shielding system rejects both radiated external interference and conducted internal noise simultaneously. This is particularly important over a 17-foot run. Why does the SI8217 use three conductors per channel rather than two? Standard RCA cables combine the negative signal return and shield drain into one conductor per channel. The SI8217 separates these into dedicated individual conductors, providing a lower-impedance signal return and isolating the shield drain from the audio signal — reducing the noise interaction that occurs in a standard two-conductor design. What is the benefit of locking split-tip connectors over standard push-fit RCA connectors? Standard push-fit RCA connectors rely on friction and can loosen under vibration, causing intermittent noise or signal dropout. The SI8217's locking split-tip connectors mechanically grip the socket with spring tension, providing a vibration-resistant hold that maintains consistent contact force over time in the automotive environment. What does the directional construction mean, and how should I orient the cable? The directional double twisted-pair winding cancels noise most effectively when signal flows from source unit to amplifier. Directional markings on the cable indicate the correct orientation. Installing in reverse does not damage the cable but reduces the effectiveness of the directional noise cancellation — particularly relevant over a longer 17-foot run. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

X1 Series 2-Channel Speaker Wire to RCA Adapter Connects OEM Head Unit Speaker Outputs to Amplifier RCA Inputs. Eliminates Line Output Converter on Compatible Amplifiers. Product Overview The Stinger X12LINE is a 2-channel RCA-to-speaker-wire adapter from the X1 Series designed for use with amplifiers that feature a balanced or differential-balanced input design. These amplifiers accept high-level speaker-level signals directly through their RCA input connections, removing the requirement for a standalone line output converter in compatible factory system integration scenarios. The X12LINE provides bare speaker wire leads at the source end for connection to the factory head unit's speaker output wiring, and 2-channel male RCA plugs at the amplifier end for direct connection to the amplifier's RCA inputs. Finished in black. Key Specifications SKU: X12LINE Series: X1 Series Configuration: Male RCA plugs to bare speaker wire leads Channels: 2 Colour: Black Compatible amplifiers: Balanced or differential-balanced RCA input design only Wire length: Not specified — confirm with Stinger Warranty: Not specified — confirm with Stinger Features & Benefits Eliminates Line Output Converter on Compatible Amplifiers Amplifiers with balanced or differential-balanced input designs accept high-level speaker signals through their RCA inputs without damage. The X12LINE provides the physical connection needed to bridge the factory head unit's speaker outputs directly to these amplifier inputs — reducing component count, wiring complexity, and installation cost compared to a dedicated LOC module. RCA Male to Bare Speaker Wire Configuration The amplifier end terminates in 2-channel male RCA plugs for direct connection to the amplifier's RCA inputs. The source end terminates in bare speaker wire leads that splice into the factory head unit's existing speaker output wiring — no additional connectors or adapters required. 2-Channel — Front, Rear, or Subwoofer Routing The 2-channel output covers stereo front or rear speaker pair integration. In compatible configurations, the two channels can also route a summed mono subwoofer signal from the factory head unit's speaker outputs to a monoblock amplifier's RCA input — where the amplifier's internal summing combines the channels as required. Compact, Simplified Installation A single adapter replaces a standalone LOC module and its associated wiring in compatible installations — reducing the number of components behind the dash and simplifying the integration of an aftermarket amplifier with a factory head unit. Technical Specs Specification Detail Brand Stinger SKU X12LINE Series X1 Series Configuration Male RCA to Bare Speaker Wire Channels 2 Colour Black Compatible Input Type Balanced / Differential-Balanced RCA Input Only Wire Length Not specified Warranty Not specified Compatible With / Goes Well With Suitable for: Amplifiers with balanced or differential-balanced input designs that explicitly support high-level input via RCA connections OEM factory head unit integration without a standalone line output converter Stereo front or rear speaker pair signal routing Mono subwoofer signal routing from factory speaker outputs to a compatible monoblock amplifier Compatible amplifier ranges (confirm high-level RCA input capability before purchasing): Rockford Fosgate amplifiers with confirmed high-level RCA input support AudioControl amplifiers with confirmed high-level RCA input support Other brands that list high-level RCA input capability in their specifications Amplifier compatibility is the critical check: The X12LINE will only work correctly with amplifiers that explicitly list high-level or speaker-level input as a supported function through the RCA connections. If the amplifier's specifications do not confirm this, a dedicated line output converter such as the Rockford Fosgate RF-HLC or RF-HLC4 is required instead. Frequently Asked Questions Can the X12LINE be used with any amplifier? No — the X12LINE is designed specifically for amplifiers with balanced or differential-balanced input designs that explicitly support high-level speaker-level signals through their RCA connections. Using this adapter with a standard amplifier that does not support high-level RCA input can damage the amplifier's input stage. What is a balanced or differential-balanced amplifier input, and why does it matter? A balanced or differential-balanced input processes the positive and negative signals independently, using the difference between them to reconstruct the audio signal and cancel common-mode noise. This architecture allows the input to accept the higher voltage levels from speaker outputs without damage, while simultaneously rejecting noise introduced by the high-level source connection. Does the X12LINE replace a line output converter entirely? In compatible installations — yes. When the amplifier supports high-level input through its RCA connections, the X12LINE provides the adapter needed to connect the factory speaker wire directly to the amplifier RCA inputs. If the amplifier does not support high-level RCA input, a dedicated line output converter is still required. How do I connect the speaker wire end of the X12LINE to the factory wiring? The bare speaker wire leads splice into the factory head unit's speaker output wiring — positive wire to each channel's positive speaker output, negative wire to each channel's negative. Refer to the vehicle's wiring diagram or the head unit's installation manual to identify the correct speaker output wires. Is the X12LINE suitable for subwoofer signal routing from a factory head unit? Yes, in compatible configurations. The 2-channel output can route a summed mono subwoofer signal from the factory head unit's speaker outputs to a monoblock amplifier's RCA input, provided the amplifier supports high-level RCA input. The amplifier's internal summing or mono input configuration combines the two channels as required. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Innova MT3320 Auto Ranging Digital Multimeter A practical and reliable digital multimeter for automotive and household electrical measurements, the MT3320 eliminates manual range selection with auto-ranging scales and adds colour-coded LED battery status indication for quick vehicle electrical diagnosis. Product Overview The MT3320 is Innova's auto-ranging digital multimeter, designed for automotive installers, technicians, and DIY users requiring accurate voltage, resistance, and battery condition measurements across both automotive and household electrical systems. Auto-ranging scales automatically select the correct measurement range when a test is made, removing the need to manually dial in the range and reducing the risk of measurement errors from incorrect range selection. A 10 megohm input impedance protects both the meter and the circuit under test from damage caused by loading, making it safe for use on sensitive automotive electronics and household circuits alike. The large digital display provides clear readings in all working conditions, and the single-setting resistance function simplifies the measurement workflow for common installation tasks. Colour-coded LEDs provide a quick visual battery condition check without requiring a separate test procedure. Protective rubber corner guards provide drop protection for workshop and on-vehicle use, and the included attachable test lead holders and stand keep the meter and leads organised and accessible during use. Features & Benefits Auto-Ranging Scales: The auto-ranging function automatically selects the correct measurement range for the input signal being measured, eliminating the need to manually dial in a range before each test. This speeds up the measurement process and prevents incorrect range selection that can produce inaccurate readings or damage the meter. 10 Megohm Input Impedance: The 10 megohm input impedance minimises the loading effect of the meter on the circuit under test, ensuring accurate voltage readings on sensitive automotive electronic circuits and household wiring without drawing significant current from the measured circuit or risking damage to delicate electronics. Colour-Coded LED Battery Quick Check: The colour-coded LED battery status display provides an immediate visual indication of battery condition without requiring a separate measurement procedure, making it a practical quick-check tool for vehicle battery diagnosis during automotive installation and service work. Large Digital Display: The large digital readout provides clear, easy-to-read measurement values in workshop lighting conditions and when working in confined under-dash or engine bay locations. Single-Setting Resistance Function: The resistance measurement function operates from a single setting, simplifying the workflow for common resistance checks performed during installation and fault-finding without requiring multiple dial positions to be navigated. Protective Rubber Corner Guards: The rubber corner guards protect the meter body from impact damage when the meter is placed on work surfaces or accidentally dropped during use, extending the service life of the instrument in workshop environments. Includes Attachable Test Lead Holders and Stand: The included attachable test lead holders keep the test leads organised and attached to the meter when not in use, and the stand allows the meter to be positioned upright on a work surface for hands-free reading during measurements. Technical Specs Specification Detail SKU MT3320 Brand Innova Type Auto-Ranging Digital Multimeter Input Impedance 10 Megohm Measurement Functions Voltage (AC and DC), Resistance Range Selection Automatic (auto-ranging) Battery Check Colour-coded LED display Display Large digital Drop Protection Rubber corner guards Inclusions Test leads, attachable test lead holders, stand Goes Well With The MT3320 is a practical diagnostic and installation tool for any automotive or marine audio installation workflow. It is well suited to checking supply voltage at amplifier terminals, verifying ground connections, measuring speaker impedance, confirming fuse continuity, and performing quick battery condition checks during and after installation. It pairs naturally with Stinger's amplifier wiring kits, circuit breakers, and the full range of F.A.E. amplifier and accessory products where electrical verification is part of the installation process. Frequently Asked Questions What measurements can the MT3320 perform? The MT3320 measures AC voltage, DC voltage, and resistance. It also provides a colour-coded LED battery quick check function for vehicle battery condition assessment. These functions cover the most common measurements needed during automotive audio installation and basic electrical fault-finding. What does auto-ranging mean, and why is it useful? Auto-ranging means the meter automatically selects the appropriate measurement scale for the signal being tested. On a manually ranged multimeter, the user must select the correct range before measuring, and selecting the wrong range produces an error reading or can damage the meter. With auto-ranging, the MT3320 detects the input level and switches to the correct range automatically, making measurements faster and eliminating incorrect range selection errors. What is the 10 megohm input impedance for? Input impedance is the resistance the meter presents to the circuit being measured. A high input impedance of 10 megohms means the meter draws very little current from the circuit under test, which has two important effects: it prevents the meter from loading down sensitive low-current circuits that could give a false reading if current were drawn, and it protects sensitive automotive electronics such as ECU circuits and sensor outputs from damage that could be caused by a low-impedance meter drawing excess current. How does the colour-coded LED battery check work? The colour-coded LEDs provide a visual indication of battery state of charge or condition during a battery quick check measurement. Different LED colours correspond to different voltage ranges, allowing a quick visual assessment of battery condition without reading a specific numerical value. This is particularly useful for a rapid go/no-go battery check during vehicle installation work without setting up a full diagnostic test. Is the MT3320 suitable for use on modern vehicle electronics? Yes. The 10 megohm input impedance makes the MT3320 safe for use on modern vehicle electronic circuits including CAN-bus wiring, sensor circuits, and low-current control signals, where a low-impedance meter could draw enough current to affect circuit behaviour or damage sensitive components.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

"Get Connected" with Our Range of Cables, Leads & Adaptors Stereo PlugThe DNA ALR035 3.5mm Stereo plug to 2 RCA plug audio lead. Features: Cable Length: 1.5 Metres Cable Colour: Black Pack Size: 1 Piece Packaging: Heat Sealed Blister & Card With Hang Hole Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

6 Metres. Video Signal. ACC Power. Reverse Trigger. Everything a Reverse Camera Needs. Product Overview The DNA Automotive RVS106F is a 6 metre RCA video extension cable with male RCA plug on one end and female RCA socket on the other and two dedicated power wires running the full length. Unlike the single-wire RVS006F, the RVS106F includes both a red ACC wire for constant or switched power supply and a yellow reversing light wire for the 12V reverse trigger signal. This makes it the more complete solution for reverse camera installations where the camera requires both a power feed and an automatic trigger that activates the camera view when reverse gear is selected. With all three wires video, ACC, and reverse trigger in a single 6 metre cable run, the RVS106F simplifies installation by eliminating the need to run a separate trigger wire from the reversing lights to the headunit or camera controller. Route once, connect all three, and the camera switches on automatically every time reverse is selected. Key Specifications Part Number: RVS106F Brand: DNA Automotive Cable Type: RCA video extension with dual power wires Connector End 1: Male RCA plug Connector End 2: Female RCA socket Red Wire: ACC — constant or switched 12V power supply Yellow Wire: Car reversing light 12V — reverse trigger signal Cable Length: 6 metres Packaging: Blister & Card Cable Gauge (wires): Not specified — confirm with supplier Video Signal Type: Not specified — confirm with supplier Shielding: Not specified — confirm with supplier Features & Benefits Two power wires — ACC and reverse trigger in one run — The RVS106F includes both the red ACC wire (for camera power supply) and the yellow reversing light wire (for the 12V reverse trigger that switches the headunit or display to camera view). Running both wires alongside the video cable means a single 6 metre cable pass handles everything — no separate reverse trigger wire needed. Yellow reverse trigger wire — automatic camera activation — The yellow wire connects to the vehicle's 12V reversing light circuit. When reverse gear is selected and the reversing lights activate, the 12V signal travels back through the yellow wire to the headunit or camera controller, automatically switching the display to reverse camera view. This is how reverse cameras are designed to work — the trigger happens without any driver input. Red ACC wire — camera power supply — The red wire connects to a 12V ACC or constant power source to supply power to the camera. Running it alongside the video and trigger wires keeps all camera wiring in one neat cable run from the rear of the vehicle to the headunit. 6 metre length — standard reverse camera run — Six metres covers most ute, SUV, wagon, and van reverse camera installations from tow bar or tailgate camera mount to the headunit in the cabin. For longer-wheelbase vehicles or caravan tow camera setups, consider the RVS010F (10 metre, single power wire) or confirm whether a 10 metre dual-wire variant is available. Male to female RCA — extend or connect — The male-to-female configuration connects directly between a camera's male RCA output and a headunit's female RCA video input, or extends an existing RCA cable where more length is needed. Technical Specs Specification Detail Part Number RVS106F Brand DNA Automotive Cable Type RCA video extension with dual power wires Connector End 1 Male RCA plug Connector End 2 Female RCA socket Red Wire ACC — 12V power supply Yellow Wire Reversing light — 12V reverse trigger Cable Length 6 metres Wire Gauge Not specified — confirm with supplier Video Signal Not specified — confirm with supplier Shielding Not specified — confirm with supplier Packaging Blister & Card Compatible With / Goes Well With Typical Applications: Reverse camera installation — full cable run (video + power + trigger) Aftermarket reverse camera upgrade on any 12V vehicle Any installation where the camera requires separate ACC power and a 12V reversing light trigger Goes Well With: Reverse cameras with RCA video output and 12V power input Aftermarket headunits with RCA reverse camera input and reverse trigger wire DNA Automotive reverse cameras and driving aid accessories DNA RVS006F (single power wire — for cameras not requiring a separate reverse trigger) Frequently Asked Questions What is the difference between this cable and the RVS006F? The RVS106F includes two power wires — a red ACC wire for camera power and a yellow reversing light trigger wire. The RVS006F includes only a single power wire. Choose the RVS106F when your installation requires both a power feed and an automatic reverse trigger in the same cable run. What does the yellow wire connect to? The yellow wire connects to the 12V reversing light positive circuit in the vehicle. When reverse gear is selected and the reversing lights activate, the 12V signal travels through the yellow wire to the headunit or display, triggering automatic camera view. It carries a trigger signal — not a high-current power supply. What does the red wire connect to? The red wire connects to a 12V ACC or switched power source to supply power to the reverse camera. Connect it to an ACC circuit that is live when the ignition is on, or to a constant 12V source depending on your camera's requirements. Can I use this cable for a front-facing dash camera? This cable is designed for reverse camera installations — the yellow trigger wire is specific to the reversing light circuit. For a front-facing dash camera, a standard RCA extension or dedicated dash cam power cable is more appropriate. Is 6 metres enough for my vehicle? Six metres covers most standard ute, SUV, and wagon reverse camera installations. For longer-wheelbase vehicles, vans, or caravan tow camera setups, a longer cable run may be required. Measure your intended cable route before ordering.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10 Metres of Clean Video Signal RCA Male to Female with Power Wire. Product Overview The DNA Automotive RVS010F is a 10 metre RCA video extension cable with male RCA plug on one end, female RCA socket on the other, and a power wire running the full length. It is the longer sibling of the RVS006F designed for installations where 6 metres is not enough to reach from the camera or video source to the display or headunit. Ten metres covers longer-wheelbase vehicles, larger vans, bus conversions, motorhomes, and caravan-to-tow-vehicle camera runs that exceed the typical 6 metre requirement. As with the RVS006F, the included power wire runs the full cable length, allowing both video signal and camera power to be routed in a single pass through trims, panels, and under carpets keeping the installation tidy and reducing the number of individual cables run through the vehicle. Key Specifications Part Number: RVS010F Brand: DNA Automotive Cable Type: RCA video extension Connector End 1: Male RCA plug Connector End 2: Female RCA socket Includes: Power wire (full length) Cable Length: 10 metres Packaging: Blister & Card Cable Gauge (power wire): Not specified — confirm with supplier Video Signal Type: Not specified — confirm with supplier Shielding: Not specified — confirm with supplier Features & Benefits 10 metre length — for longer vehicle and tow camera runs — Where the 6 metre RVS006F falls short, the RVS010F picks up. Ten metres handles longer-wheelbase utes and vans, motorhomes, bus conversions, and caravan tow camera setups where the camera is mounted on the caravan or trailer and the cable must run back through a tow harness or along the vehicle to a cabin display. Male RCA to female RCA — extend or connect — The male-to-female configuration extends an existing RCA cable or connects directly between a camera's male RCA output and a headunit or monitor's female RCA input. Plug in, route, done. Power wire included — single cable run — The full-length power wire runs alongside the video cable, keeping both signal and camera power in one tidy run through door trims, headliners, and under-carpet routing. Fewer cables, cleaner installation. Purpose-built for rear camera and driving aid installations — The 10 metre length is specifically suited to applications where the camera is further from the display than a standard 6 metre cable can bridge — tow bars on long-wheelbase vehicles, caravan-mounted cameras, and extended cab or body van setups. Technical Specs Specification Detail Part Number RVS010F Brand DNA Automotive Cable Type RCA video extension Connector End 1 Male RCA plug Connector End 2 Female RCA socket Power Wire Included — full 10 metre length Cable Length 10 metres Power Wire Gauge Not specified — confirm with supplier Video Signal Not specified — confirm with supplier Shielding Not specified — confirm with supplier Packaging Blister & Card Compatible With / Goes Well With Typical Applications: Long-run reverse camera video signal extension Caravan and trailer tow camera video cable Motorhome and bus conversion rear camera runs Blind spot and side camera installations on larger vehicles Any 12V AV installation requiring a 10 metre RCA video run Goes Well With: Reverse cameras with RCA video output Aftermarket headunits with RCA video input Rear-view monitors with RCA input DNA RVS006F (6 metre version — for shorter runs) Frequently Asked Questions When should I choose the 10 metre cable over the 6 metre RVS006F? Choose the RVS010F when your camera-to-display run exceeds 6 metres — common in long-wheelbase utes, vans, motorhomes, and caravan tow camera setups where the camera is mounted further from the cabin than a 6 metre cable can reach. Can this cable extend an existing shorter RCA video cable? Yes. Connect the male RCA plug to the female socket of an existing cable and run the female socket end of the RVS010F to your headunit or display, adding 10 metres to the total cable run. Does the power wire run the full 10 metres? Yes — the power wire is included and runs the full 10 metre length, allowing both video signal and camera power to be routed together in a single cable pass through the vehicle. Is this cable suitable for a caravan or trailer tow camera? Yes — the 10 metre length is specifically suited to caravan and trailer camera setups where the camera is mounted at the rear of the trailer and the cable must run back through a connector or along the tow vehicle to reach the cabin display. Confirm the total cable run for your specific setup before ordering. What is the power wire gauge? Power wire gauge is not confirmed in the available product data. Contact us or refer to DNA Automotive's product documentation if wire gauge is a requirement for your installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Pioneer CD-U5110AC USB-A to USB-C Cable 1m with Confirmed CarPlay and Android Auto Support A 1m soft touch silicon USB-A to USB-C cable from Pioneer with confirmed Apple CarPlay and Android Auto compatibility with Pioneer receivers, 5V/3A support, tangle-resistant design, and a storage strap included. Product Overview The Pioneer CD-U5110AC is a 1m USB-A male to USB-C male cable engineered for daily use with Pioneer head unit receivers. Featuring a soft touch, tangle-resistant silicon material cover and confirmed CarPlay and Android Auto support with Pioneer receivers, the CD-U5110AC is designed to deliver reliable wired smartphone connectivity day after day. The cable supports 5V/3A and USB 2.0 data communication up to 480Mbps (theoretical value). A storage strap is included for tidy storage when not in use. Features & Benefits Confirmed CarPlay and Android Auto Support: The CD-U5110AC is confirmed compatible with Apple CarPlay and Android Auto when used with Pioneer receivers, providing reliable wired smartphone integration without connectivity issues. Soft Touch Tangle-Resistant Silicon Material: The silicon material cover is soft to touch and tangle-resistant, making it durable and easy to manage in daily use compared to standard PVC cables. 5V/3A Power Support: Supports 5V/3A for reliable power delivery to connected devices alongside data communication. USB 2.0 with Up to 480Mbps Data Speed: Compatible with USB 2.0 and supports data communication speeds up to 480Mbps (theoretical value) for CarPlay, Android Auto, and media playback. 1m Length: The 1m length provides a practical, tidy connection between a Pioneer head unit and a smartphone without excess cable bulk in the cabin. Storage Strap Included: A storage strap is included for neat cable storage when not in use. Technical Specs Specification Detail SKU CD-U5110AC Brand Pioneer Type USB-A to USB-C Cable Length 1m Connector USB-A Male to USB-C Male Supported Voltage / Current 5V / 3A USB Standard USB 2.0 Data Speed Up to 480Mbps (theoretical value) Material Soft Touch Silicon CarPlay / Android Auto Confirmed compatible with Pioneer receivers Operating Temperature -10°C to 60°C Storage Temperature -20°C to 80°C Included Storage Strap What's in the Box Pioneer CD-U5110AC USB-A to USB-C Cable (1m) Storage Strap Frequently Asked Questions Is the CD-U5110AC confirmed to work with Apple CarPlay and Android Auto? Yes. The CD-U5110AC is confirmed compatible with Apple CarPlay and Android Auto when used with Pioneer receivers, providing reliable wired smartphone connectivity without the connection issues that can occur with uncertified third-party cables. What devices use a USB-C connection for CarPlay or Android Auto? USB-C is the standard connector on most modern Android smartphones and iPhone 15 and later models. Please confirm your smartphone uses a USB-C connector before purchasing. If your device uses a Lightning connector, a different cable will be required. Is the CD-U5110AC compatible with non-Pioneer head units? The CD-U5110AC is confirmed compatible with Pioneer receivers. Compatibility with head units from other brands may vary. Please check your head unit's specifications before purchasing. Does this cable support fast charging? The CD-U5110AC supports 5V/3A, which provides standard USB charging. It is not rated for USB Power Delivery or proprietary fast charging protocols. For fast charging, please check whether your device and charger require a specific fast charging cable. What is the difference between this cable and a standard USB-A to USB-C cable? The CD-U5110AC is specifically confirmed for CarPlay and Android Auto compatibility with Pioneer receivers, uses a tangle-resistant soft touch silicon cover for durability, and includes Pioneer branding and a storage strap. Standard third-party cables may not be certified for CarPlay or Android Auto and may cause intermittent connectivity issues.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less