GME ABL002 Elevated-Feed Stainless Steel Antenna Base Ground Independent with 4.5M Low-Loss Foam Coax A ground-independent elevated-feed antenna base from GME, the ABL002 is constructed from stainless steel with 4.5 metres of low-loss foam coaxial cable and a BSW thread, suiting fibreglass, aluminium, and non-metallic vehicle and vessel bodies as well as conventional steel bodies without requiring the vehicle body as a ground plane. Product overview The GME ABL002 is an elevated-feed, ground-independent antenna base designed to operate without relying on the vehicle's metal body as a ground plane. This makes it the appropriate choice for fibreglass boats, aluminium canopies, non-metallic roof racks, and similar installations where a conventional ground-dependent base such as the ABL001 would perform poorly. The ABL002 also works correctly on standard steel-bodied vehicles. The stainless steel construction provides corrosion resistance suited to marine, coastal, and harsh outdoor environments. The 4.5m low-loss foam coaxial cable matches the specification used on the ABL001, minimising signal attenuation over the full cable run. Note: the ABL002 uses a BSW (British Standard Whitworth) thread, which is a different standard from the 5/16" TPI thread used on the GME AB001, AB406, and ABL001. Confirm your antenna uses a BSW thread base before purchasing, as the two thread standards are not interchangeable. Features and benefits Ground-independent elevated-feed design - suits non-metallic bodies: The elevated-feed design builds the counterpoise into the base itself, generating its own ground plane without depending on the mounting surface material. This makes the ABL002 suitable for fibreglass, aluminium, plastic, and other non-metallic vehicle and vessel bodies, as well as conventional steel bodies. Stainless steel construction - corrosion resistant: The stainless steel finish resists corrosion from salt water, road grime, and UV exposure, maintaining a reliable electrical connection at the antenna mount over years of outdoor and marine service. 4.5m low-loss foam coaxial cable: The same low-loss foam coaxial cable specification as the ABL001, minimising signal attenuation over the full cable run for improved signal performance. BSW thread: Uses a British Standard Whitworth thread, a different standard from the 5/16" TPI thread used on other GME antenna bases. Confirm your antenna uses a BSW thread base before purchasing. Suits 4WD, marine, and recreational applications: The ground-independent design and stainless steel finish make the ABL002 equally suited to boats, fibreglass 4WD canopies, and similar off-road and marine applications. Technical specs Specification Detail SKU ABL002 Brand GME Type Elevated-Feed Antenna Base and Lead Lead Length 4.5m Cable Type Low-Loss Foam Coaxial Thread BSW (British Standard Whitworth) Design Ground Independent (Elevated Feed) Construction Stainless Steel Compatible with The ABL002 is compatible with antennas using a BSW thread base. Confirm your antenna uses a BSW thread before purchasing, as this differs from the 5/16" TPI standard used on other GME antenna bases. Suitable for fibreglass, aluminium, steel, and non-metallic vehicle and vessel bodies, including fibreglass boats, aluminium ute canopies, and non-metallic roof structures. Frequently asked questions What is an elevated-feed design and why does it make this base ground independent?In a conventional ground-dependent antenna base, the electrical ground return path runs through the mounting surface and vehicle body. An elevated-feed design builds the counterpoise into the base itself, raising the feed point away from the mounting surface so the antenna generates its own ground plane without depending on the mounting material. This makes it suitable for non-metallic surfaces where a conventional base would perform poorly. How does BSW thread differ from 5/16" TPI?BSW and 5/16" TPI are two different thread standards that are not interchangeable. A BSW antenna base will not correctly accept a 5/16" TPI antenna whip and vice versa. Check your intended antenna's specification to confirm it uses a BSW thread before purchasing the ABL002. GME's other antenna bases including the AB001, AB406, and ABL001 use 5/16" TPI. Why is stainless steel preferred for antenna bases in marine and 4WD use?Stainless steel resists corrosion from salt water, road grime, and UV exposure far better than standard steel or zinc-plated finishes. For marine installations in particular, salt air rapidly corrodes unprotected metals, and a stainless base maintains a reliable electrical connection at the antenna mount over years of outdoor service. Can the ABL002 be used on a conventional steel-bodied vehicle?Yes. The ground-independent design works on steel bodies as well as non-metallic surfaces. On a standard steel vehicle a ground-dependent base such as the ABL001 will also perform well. The ABL002's ground-independent design is most valuable where the mounting surface is non-metallic. How does the ABL002 compare to the ABL001?Both bases include 4.5m of low-loss foam coaxial cable. The ABL001 uses 5/16" TPI thread, a ground-dependent design, and is confirmed to suit 27MHz and 477MHz antennas. The ABL002 uses BSW thread, a ground-independent elevated-feed design, and stainless steel construction. The ABL002 is the appropriate choice for non-metallic mounting surfaces, while the ABL001 suits standard steel-bodied installations. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GME ABL001 4.5M Universal Antenna Base and Lead with PL259 Connector for 27MHz and 477MHz UHF CB A universal antenna base and lead from GME, the ABL001 includes 4.5 metres of low-loss foam coaxial cable and a standard PL259 connector, suits both 27MHz CB and 477MHz UHF CB antennas with a 5/16" TPI thread, and uses a ground-dependent design requiring a ferrous steel vehicle body for antenna ground plane. Product overview The GME ABL001 is a universal antenna base with 4.5m of low-loss foam coaxial cable and a PL259 connector, suited to both 27MHz CB and 477MHz UHF CB antenna whips with a 5/16" TPI base thread. The low-loss foam coaxial construction minimises signal attenuation over the cable run, and the 4.5m length provides sufficient routing length for most standard vehicle installations. The ABL001 uses a ground-dependent design, meaning the vehicle's metal body acts as the antenna ground plane. This is the conventional setup for most CB and UHF CB vehicle installations on steel-bodied vehicles. It is not suitable for vehicles with fibreglass, aluminium, or other non-metallic bodies where a no-ground plane (NGP) antenna system is required instead. Features and benefits 4.5m low-loss foam coaxial cable - minimised signal attenuation: The low-loss foam coaxial construction uses a foamed polyethylene dielectric to reduce signal attenuation over the cable run compared to standard solid-dielectric coax of the same length, delivering more of the radio's signal to the antenna and improving received signal performance. Standard PL259 connector - direct radio connection: The industry-standard PL259 plug connects directly to most CB and UHF CB radio antenna inputs without additional adaptors. 5/16" TPI thread - standard Australian CB and UHF CB specification: Accepts the majority of Australian UHF CB and CB antenna whips using the common 5/16" TPI thread standard from GME and other compatible brands. Dual frequency compatibility - 27MHz CB and 477MHz UHF CB: The ABL001 suits antennas for both 27MHz traditional CB and 477MHz UHF CB from a single base, covering both frequency bands in one product. Ground-dependent design - conventional vehicle installation: Uses the vehicle's steel body as the antenna ground plane for conventional CB and UHF CB antenna performance on steel-bodied vehicles. Universal - broad vehicle and mounting compatibility: Not vehicle-specific and suits a wide range of mounting configurations across different vehicle types with steel bodies. Technical specs Specification Detail SKU ABL001 Brand GME Type Universal Antenna Base and Lead Lead Length 4.5m Cable Type Low-Loss Foam Coaxial Connector PL259 Thread 5/16" TPI Compatible Frequencies 27MHz CB and 477MHz UHF CB Design Ground Dependent Weight 0.49kg Compatible with The ABL001 is compatible with standard 5/16" TPI CB and UHF CB antenna whips from GME and other compatible brands. Suits 27MHz CB radios and 477MHz UHF CB radios with a PL259 antenna input. Requires a ferrous steel vehicle body for ground plane. Not suitable for aluminium, fibreglass, or non-metallic vehicle bodies. Frequently asked questions What does ground dependent mean for antenna performance?A ground-dependent antenna base uses the metal body of the vehicle as an electrical ground plane, which is the conventional design for most vehicle CB and UHF CB installations. Vehicles with fibreglass, aluminium, or other non-metallic bodies do not provide the required ground plane, and a no-ground plane (NGP) antenna system is required for these applications. What is low-loss foam coaxial cable?Low-loss foam coaxial cable uses a foamed polyethylene dielectric instead of solid PE, which lowers signal attenuation compared to standard solid-dielectric coax of the same length. This means more of the signal from the radio reaches the antenna and vice versa, particularly meaningful over longer cable runs. Is 4.5m enough cable for most vehicle installations?For most standard vehicle installations routing from the antenna mount through the A-pillar or door seal and under the dash to the radio, 4.5m is typically sufficient. Larger vehicles such as trucks or installations requiring chassis routing may need additional cable length via a compatible coaxial extension. Will the ABL001 work on a vehicle with an aluminium or fibreglass body?No. The ground-dependent design requires a steel ferrous vehicle body to provide the antenna ground plane. On aluminium, fibreglass, or plastic-bodied vehicles, a no-ground plane (NGP) antenna system is required for correct antenna performance. How does the ABL001 differ from the AB001 and AB406?The AB001 is a universal base only with no cable or connector included. The AB406 is a magnetic base with lead and plug for non-permanent steel surface mounting. The ABL001 is a fixed base with 4.5m of specified low-loss foam coax, a PL259 connector, 5/16" TPI thread, dual 27/477MHz compatibility, and a confirmed ground-dependent design. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GME AB001 Universal Antenna Base for 27MHz CB and 477MHz UHF CB Antennas A genuine universal antenna base from GME, the AB001 suits both 27MHz CB antennas and 477MHz UHF CB antennas with a standard 5/16" TPI thread, providing a compatible mounting base for a wide range of GME and compatible antennas across both frequency bands. Product overview The GME AB001 is a universal antenna base designed to accept both 27MHz CB and 477MHz UHF CB antennas using the standard 5/16" TPI thread specification common across the Australian CB and UHF CB market. It is not vehicle-specific and can be used across a range of vehicle and fixed installation types. Confirm the mounting style, cable inclusions, and antenna thread compatibility before purchase. Features and benefits Dual frequency compatibility - 27MHz CB and 477MHz UHF CB: The AB001 suits antennas for both 27MHz traditional CB and 477MHz UHF CB from a single base, providing broad frequency coverage for mixed CB and UHF installations. 5/16" TPI thread - standard Australian CB and UHF market specification: The 5/16" TPI thread is one of the most common antenna base thread standards in the Australian CB and UHF CB market, compatible with GME and many other antenna brands using the same thread specification. Universal design - broad installation compatibility: The AB001 is not vehicle-specific and suits a range of vehicle and fixed installation types for flexible antenna deployment. Genuine GME accessory: A genuine GME-manufactured antenna base ensuring correct thread specification and compatibility within the GME antenna system. Technical specs Specification Detail SKU AB001 Brand GME Type Universal Antenna Base Compatible Frequencies 27MHz CB and 477MHz UHF CB Thread 5/16" TPI Compatible with The AB001 is compatible with GME 27MHz CB antennas and GME 477MHz UHF CB antennas using a 5/16" TPI thread. Compatible antennas from other brands using the same 5/16" TPI thread standard may also suit. Confirm your specific antenna thread specification before purchase. Contact us to confirm compatibility with your specific GME antenna model. Frequently asked questions What is the difference between 27MHz and 477MHz for CB radio?27MHz is the frequency band used by traditional AM and SSB Citizens Band CB radio, which was the dominant vehicle communication standard in Australia for many decades. 477MHz is the current Australian UHF CB standard operating across 80 channels, offering clearer audio and better performance in most environments. The AB001 suits antenna types for both systems. What is 5/16" TPI and what antennas use this thread?5/16" TPI refers to the thread diameter and pitch of the antenna base connection point. It is one of the most common antenna thread standards in the Australian CB and UHF CB market and is used by GME and many other antenna brands. Confirm that your chosen antenna has a male 5/16" TPI base thread before purchasing. What mounting style does the AB001 use?The mounting style of the AB001 is not confirmed in the available source data. Common antenna base mounting types include magnetic, gutter mount, body hole mount, and stud mount. Contact us to confirm the mounting method before purchasing. Is a coaxial cable included with the AB001?Cable inclusions are not confirmed in the available source data. Contact us before purchasing to confirm whether a coaxial cable is supplied or must be sourced separately. Is the AB001 compatible with antennas from other brands?The AB001 uses a standard 5/16" TPI thread which is common across many Australian CB and UHF CB antenna brands. Antennas from other brands using the same 5/16" TPI thread specification may be compatible. Confirm thread specification with your antenna manufacturer before purchasing. Frequently Asked Questions What is the difference between 27 MHz and 477 MHz for CB radio? 27 MHz is the frequency band used by traditional AM/SSB Citizens Band (CB) radio, which was the dominant vehicle-to-vehicle and recreational communication standard in Australia for many decades. 477 MHz is the frequency band used by UHF CB radio — the current standard in Australia for recreational 4WD, caravan, and farm communication. UHF CB operates on 80 channels and offers clearer audio, more channels, and generally better performance in built-up areas. The GME AB001 suits antenna types for both systems. What is 5/16" TPI and what antennas use this thread? 5/16" TPI (threads per inch) is a standard thread specification for antenna bases. In Australia's CB and UHF CB market, the 5/16" antenna thread is one of the most common standards, used by GME and many other antenna brands. Before purchasing, confirm that your chosen antenna has a male 5/16" TPI base thread to ensure it will connect to this base correctly. What mounting style does this antenna base use? The mounting style for the AB001 is not confirmed in the available supplier data. Common antenna base mounting types include magnetic (non-permanent, sits on the vehicle roof), gutter mount (clamps to the door or window gutter), body hole mount (requires a drilled hole), and stud mount. Confirm the mounting method with GME or your supplier before purchasing. Is a coaxial cable included with this base? Cable inclusions are not confirmed in the available supplier data. Confirm whether a coaxial cable and PL-259 or BNC connector is supplied, or needs to be purchased separately, with GME or your supplier. Will this base suit my GME TX6160 or TX3350 UHF radio antenna? The AB001 is specified for 477 MHz UHF antennas, which covers GME's current UHF CB range. Confirm with GME that the AB001 is compatible with your specific GME antenna model before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GME XRS-RJ45W9 Pass-Through Adaptor Mitsubishi White LED A pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45W9 integrates an XRS Connect controller microphone directly into a factory blank switch location on selected Mitsubishi models, featuring a CAT.6 compliant fully-shielded housing, white LED back-light, and a simple two-wire installation. Product Overview The GME XRS-RJ45W9 is part of GME's accessory range complementing their XRS Connect UHF CB radios. The pass-through adaptor allows an XRS Connect controller microphone to be integrated directly into a range of blank OEM switch locations, providing a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with dual lateral supports front and back, the XRS-RJ45W9 minimises RF interference and ensures an extremely stable connection for trouble-free communication. The white LED back-light illuminates the switch to match factory switch illumination, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Features & Benefits Integrates with Existing Factory Switches: The XRS-RJ45W9 integrates directly into a blank OEM switch location, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing minimises RF interference for reliable, trouble-free UHF communication. Dual Lateral Support Construction: Internal dual lateral supports front and back provide an extremely stable RJ45 connection that resists vibration and everyday use. White LED Back-Light: The white LED back-light illuminates to match white factory switch illumination, keeping the dash lighting consistent. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45W9 Brand GME Description Pass-Through Adaptor for Mitsubishi, White LED LED Colour White Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios Compatible With The XRS-RJ45W9 is compatible with the following Mitsubishi models: Triton MQ (2015-2018), Triton MR (2019-2023), Pajero Sport KR, KS, QE (2015-2021), and Outlander ZK (2012-2021). It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your vehicle model and year, and check GME's compatibility matrix, before purchase. Frequently Asked Questions What does the XRS-RJ45W9 do? The XRS-RJ45W9 lets an XRS Connect controller microphone be integrated directly into a factory blank switch location on selected Mitsubishi models, giving a neat, factory-look finish instead of a dash-mounted mic. Which Mitsubishi models does it suit? The XRS-RJ45W9 suits the Triton MQ (2015-2018), Triton MR (2019-2023), Pajero Sport KR, KS, and QE (2015-2021), and Outlander ZK (2012-2021). Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45W9 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the white LED back-light work? The white LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit, illuminating in white to match factory switch lighting. Is there a coloured LED version available? Yes. GME also offers the XRS-RJ45R9, the same pass-through adaptor with a red LED back-light instead of white, for the same range of Mitsubishi models. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from Brand Beast today!

Read more less

GME XRS-RJ45W8 Pass-Through Adaptor Nissan White LED A pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45W8 integrates an XRS Connect controller microphone directly into a factory blank switch location on selected Nissan models, featuring a CAT.6 compliant fully-shielded housing, white LED back-light, a compact 30.6 x 23.5mm size, and Australian made construction. Product Overview The GME XRS-RJ45W8 is part of GME's accessory range complementing their XRS Connect UHF CB radios. The pass-through adaptor allows an XRS Connect controller microphone to be integrated directly into a range of blank OEM switch locations on selected Nissan models, providing a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with dual lateral supports front and back, the XRS-RJ45W8 minimises RF interference and ensures an extremely stable connection for trouble-free communication. The white LED back-light illuminates the switch to match factory switch illumination, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. The compact 30.6 x 23.5mm adaptor is made in Australia. Features & Benefits Integrates with Existing Factory Switches: The XRS-RJ45W8 integrates directly into a blank OEM switch location on selected Nissan models, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing minimises RF interference for reliable, trouble-free UHF communication. Dual Lateral Support Construction: Internal dual lateral supports front and back provide an extremely stable RJ45 connection that resists vibration and everyday use. White LED Back-Light: The white LED back-light illuminates to match white factory switch illumination, keeping the dash lighting consistent. Compact 30.6 x 23.5mm Size: The compact adaptor size fits neatly into the factory blank switch location without disrupting the surrounding dash layout. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Made in Australia: The XRS-RJ45W8 is manufactured in Australia to GME's quality standards. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45W8 Brand GME Description RJ45 Pass-Through Adaptor Type 8 (White) for Nissan LED Colour White Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Size 30.6 x 23.5mm Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Country of Origin Australia Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios In the Box Adaptor Only Compatible With The XRS-RJ45W8 is compatible with the following Nissan models per GME's compatibility matrix: Patrol GU Series 4-8 (2004-2018), Patrol Y62 (2016-Current), Pathfinder R51 (2005-2012), Pathfinder R52 (2012-2020), X-Trail T31 (2007-2014), X-Trail T32 (2014-2022), Navara D40 (2008-2014), and Navara NP300 (2016-Current, handbrake console location). It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your vehicle model and year against GME's compatibility matrix before purchase. Frequently Asked Questions What does the XRS-RJ45W8 do? The XRS-RJ45W8 lets an XRS Connect controller microphone be integrated directly into a factory blank switch location on selected Nissan models, giving a neat, factory-look finish instead of a dash-mounted mic. Which Nissan models does it suit? Per GME's compatibility matrix, the XRS-RJ45W8 suits the Patrol GU Series 4-8, Patrol Y62, Pathfinder R51 and R52, X-Trail T31 and T32, and Navara D40 and NP300. Confirm your exact model and year before purchase. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45W8 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the white LED back-light work? The white LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit, illuminating in white to match factory switch lighting. Is there a coloured LED version available? Yes. GME also offers the XRS-RJ45R8, the same pass-through adaptor with a red LED back-light instead of white, for the same range of Nissan models. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from Brand Beast today!

Read more less

GME XRS-RJ45W10 Pass-Through Adaptor Toyota Landcruiser 79 White LED A genuine GME pass-through adaptor for XRS Connect UHF CB radios, the XRS-RJ45W10 integrates an XRS Connect controller microphone directly into a factory blank switch location on the Toyota Landcruiser 79 Series (2021-Current), featuring a CAT.6 compliant fully-shielded housing and a white LED back-light. Product Overview The GME XRS-RJ45W10 is a genuine GME accessory from the XRS Connect range, allowing an XRS Connect controller microphone to be integrated directly into a blank OEM switch location on the Toyota Landcruiser 79 Series from 2021 onwards. This provides a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with internal supports, the XRS-RJ45W10 ensures an extremely stable connection for trouble-free communication. The white LED back-light illuminates the switch to match factory switch illumination, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Features & Benefits Genuine GME Accessory: The XRS-RJ45W10 is a genuine GME accessory purpose-built for the XRS Connect range, ensuring correct fitment and compatibility. Integrates with Existing Factory Switches: The XRS-RJ45W10 integrates directly into a blank OEM switch location on the Landcruiser 79 Series, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing with internal supports ensures an extremely stable connection for reliable, trouble-free UHF communication. White LED Back-Light: The white LED back-light illuminates to match white factory switch illumination, keeping the dash lighting consistent. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Compatible with Other RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45W10 Brand GME Description RJ45 Pass-Through Adaptor Type 10 (White) for Toyota Landcruiser 79 Series LED Colour White Connector Type RJ45 Housing CAT.6 Compliant, Fully-Shielded Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Suits XRS Connect UHF CB Radios and Other RJ45 UHF Radios Compatible With The XRS-RJ45W10 is compatible with the Toyota Landcruiser 79 Series (2021-Current). It is also compatible with other UHF CB radios using an RJ45 connection. Confirm your vehicle model and year before purchase. Frequently Asked Questions What does the XRS-RJ45W10 do? The XRS-RJ45W10 lets an XRS Connect controller microphone be integrated into a factory blank switch location on the Toyota Landcruiser 79 Series, giving a neat, factory-look finish instead of a dash-mounted mic. Which vehicles does it suit? The XRS-RJ45W10 is compatible with the Toyota Landcruiser 79 Series from 2021 onwards. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45W10 is also compatible with other UHF CB radios that use an RJ45 connection. How does the white LED back-light work? The white LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit, illuminating in white to match factory switch lighting. Is there a coloured LED version available? Yes. GME also offers the XRS-RJ45R10, the same pass-through adaptor with a red LED back-light instead of white, for the same Landcruiser 79 Series fitment. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from Brand Beast today!

Read more less

GME XRS-RJ45R8 Pass-Through Adaptor Nissan Red LED A pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45R8 integrates an XRS Connect controller microphone directly into a factory blank switch location on selected Nissan models, featuring a CAT.6 compliant fully-shielded housing, red LED back-light, a compact 30.6 x 23.5mm size, and Australian made construction. Product Overview The GME XRS-RJ45R8 is part of GME's accessory range complementing their XRS Connect UHF CB radios. The pass-through adaptor allows an XRS Connect controller microphone to be integrated directly into a range of blank OEM switch locations on selected Nissan models, providing a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with dual lateral supports front and back, the XRS-RJ45R8 minimises RF interference and ensures an extremely stable connection for trouble-free communication. The red LED back-light illuminates the switch, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. The compact 30.6 x 23.5mm adaptor is made in Australia. Features & Benefits Integrates with Existing Factory Switches: The XRS-RJ45R8 integrates directly into a blank OEM switch location on selected Nissan models, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing minimises RF interference for reliable, trouble-free UHF communication. Dual Lateral Support Construction: Internal dual lateral supports front and back provide an extremely stable RJ45 connection that resists vibration and everyday use. Red LED Back-Light: The red LED back-light illuminates the switch for clear visibility on the factory dash. Compact 30.6 x 23.5mm Size: The compact adaptor size fits neatly into the factory blank switch location without disrupting the surrounding dash layout. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Made in Australia: The XRS-RJ45R8 is manufactured in Australia to GME's quality standards. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45R8 Brand GME Description RJ45 Pass-Through Adaptor Type 8 (Red) for Nissan LED Colour Red Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Size 30.6 x 23.5mm Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Country of Origin Australia Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios In the Box Adaptor Only Compatible With The XRS-RJ45R8 is compatible with the following Nissan models per GME's compatibility matrix: Navara NP300 (2016-Current, lower switch fascia under A/C controls where fitted), Pathfinder R52 (2012-2020), X-Trail T32 (2014-2022), and Navara D40 (2008-2014). It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your vehicle model and year against GME's compatibility matrix before purchase. Frequently Asked Questions What does the XRS-RJ45R8 do? The XRS-RJ45R8 lets an XRS Connect controller microphone be integrated into a factory blank switch location on selected Nissan models, giving a neat, factory-look finish instead of a dash-mounted mic. Which Nissan models does it suit? Per GME's compatibility matrix, the XRS-RJ45R8 suits the Navara NP300 at the lower switch fascia under the A/C controls, Pathfinder R52, X-Trail T32, and Navara D40. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45R8 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the red LED back-light work? The red LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Is there a white LED version available? Yes. GME also offers the XRS-RJ45W8, the same pass-through adaptor with a white LED back-light instead of red, for the same range of Nissan models. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized GME dealer today!

Read more less

GME XRS-RJ45R6 Universal Pass-Through Adaptor Red LED A universal pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45R6 integrates an XRS Connect controller microphone into any flat mounting surface across agriculture machinery, 4WD vehicles, and heavy vehicles, featuring a CAT.6 compliant fully-shielded housing, red LED back-light, and Australian made construction. Product Overview The GME XRS-RJ45R6 is a universal pass-through adaptor from GME's XRS Connect accessory range, designed for applications beyond the vehicle-specific OEM switch adaptors. Rather than fitting a single factory blank switch location, the XRS-RJ45R6 is ideally suited to a number of locations across a variety of vehicles, including agriculture machinery, 4WD vehicles, heavy vehicles, or any fitment on a flat surface, providing a neat and professional finish wherever it's installed. Featuring a CAT.6 compliant, fully-shielded housing with dual lateral supports front and back, the XRS-RJ45R6 minimises RF interference and ensures an extremely stable connection for trouble-free communication. The red LED back-light illuminates the switch, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. The adaptor requires a 21mm x 37mm switch cut-out in a panel up to 2.0mm thick, with a total mounting depth of 26mm excluding cable exit, and is made in Australia. Features & Benefits Ideally Suited for Universal Applications: Unlike the vehicle-specific OEM adaptors, the XRS-RJ45R6 suits any flat mounting surface, making it a versatile option across agriculture machinery, 4WD vehicles, and heavy vehicles. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing minimises RF interference for reliable, trouble-free UHF communication. Dual Lateral Support Construction: Internal dual lateral supports front and back provide an extremely stable RJ45 connection that resists vibration and everyday use. Red LED Back-Light: The red LED back-light illuminates the switch for clear visibility and a distinctive look on the mounting panel. Defined Cut-Out and Mounting Depth: A 21mm x 37mm switch cut-out in a panel up to 2.0mm thick and a 26mm mounting depth excluding cable exit make planning the installation straightforward. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Made in Australia: The XRS-RJ45R6 is manufactured in Australia to GME's quality standards. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45R6 Brand GME Description RJ45 Pass-Through Adaptor Type 6 (Red), Universal LED Colour Red Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Mounting Depth (Excluding Cable Exit) 26mm Switch Cut-Out Size 21mm x 37mm (2.0mm Panel Thickness) Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Country of Origin Australia Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios In the Box Adaptor Only Compatible With The XRS-RJ45R6 is a universal fitment adaptor suited to any flat mounting surface with a 21mm x 37mm cut-out, including agriculture machinery, 4WD vehicles, and heavy vehicles, rather than a specific factory switch location. It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your intended mounting panel thickness and available depth before purchase. Frequently Asked Questions What does the XRS-RJ45R6 do? The XRS-RJ45R6 lets an XRS Connect controller microphone be mounted into any flat panel with a 21mm x 37mm cut-out, rather than a specific factory switch blank, making it suited to agriculture machinery, 4WD vehicles, and heavy vehicles. What cut-out size do I need? The XRS-RJ45R6 requires a 21mm x 37mm switch cut-out in a panel up to 2.0mm thick, with a total mounting depth of 26mm excluding the cable exit. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45R6 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the red LED back-light work? The red LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Is there a white LED version available? Yes. GME also offers the XRS-RJ45W6, the same universal pass-through adaptor with a white LED back-light instead of red. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized GME dealer today!

Read more less

GME XRS-RJ45R4 Pass-Through Adaptor Isuzu Red LED A pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45R4 integrates an XRS Connect controller microphone directly into a factory blank switch location on selected Isuzu models, featuring a CAT.6 compliant fully-shielded housing, red LED back-light, and Australian made construction. Product Overview The GME XRS-RJ45R4 is part of GME's accessory range complementing their XRS Connect UHF CB radios. The pass-through adaptor allows an XRS Connect controller microphone to be integrated directly into a range of blank OEM switch locations on selected Isuzu models, providing a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with internal supports, the XRS-RJ45R4 ensures an extremely stable connection for trouble-free communication. The red LED back-light illuminates the switch, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. The adaptor is made in Australia. Features & Benefits Integrates with Existing Factory Switches: The XRS-RJ45R4 integrates directly into a blank OEM switch location on selected Isuzu models, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing with internal supports ensures an extremely stable connection for reliable, trouble-free UHF communication. Red LED Back-Light: The red LED back-light illuminates the switch for clear visibility on the factory dash. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Made in Australia: The XRS-RJ45R4 is manufactured in Australia to GME's quality standards. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45R4 Brand GME Description RJ45 Pass-Through Adaptor Type 4 (Red) for Isuzu LED Colour Red Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Country of Origin Australia Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios In the Box Adaptor Only Compatible With The XRS-RJ45R4 is compatible with the following Isuzu models per GME's compatibility matrix: D-Max 2nd Generation (2012-2020) and MU-X 1st Generation (2012-2021), both fitting the lower switch fascia under the A/C controls where fitted. It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your vehicle model and year, and check that your vehicle has the lower switch fascia fitted, before purchase. Frequently Asked Questions What does the XRS-RJ45R4 do? The XRS-RJ45R4 lets an XRS Connect controller microphone be integrated into a factory blank switch location on selected Isuzu models, giving a neat, factory-look finish instead of a dash-mounted mic. Which Isuzu models does it suit? Per GME's compatibility matrix, the XRS-RJ45R4 suits the D-Max 2nd Generation (2012-2020) and MU-X 1st Generation (2012-2021), both at the lower switch fascia under the A/C controls where fitted. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45R4 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the red LED back-light work? The red LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Is there a white LED version available? Yes. GME also offers the XRS-RJ45W4, the same pass-through adaptor with a white LED back-light instead of red, for the same range of Isuzu models. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized GME dealer today!

Read more less

GME XRS-RJ45R3 Pass-Through Adaptor Nissan Red LED A pass-through adaptor for GME XRS Connect UHF CB radios, the XRS-RJ45R3 integrates an XRS Connect controller microphone directly into a factory blank switch location on selected Nissan models, featuring a CAT.6 compliant fully-shielded housing, red LED back-light, a compact 40.5 x 21.3mm size, and Australian made construction. Product Overview The GME XRS-RJ45R3 is part of GME's accessory range complementing their XRS Connect UHF CB radios. The pass-through adaptor allows an XRS Connect controller microphone to be integrated directly into a range of blank OEM switch locations on selected Nissan models, providing a neat and professional finish that looks factory fitted rather than aftermarket. Featuring a CAT.6 compliant, fully-shielded housing with internal supports, the XRS-RJ45R3 ensures an extremely stable connection for trouble-free communication. The red LED back-light illuminates the switch, and installation is a simple two-wire connection, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. The compact 40.5 x 21.3mm adaptor is made in Australia. Features & Benefits Integrates with Existing Factory Switches: The XRS-RJ45R3 integrates directly into a blank OEM switch location on selected Nissan models, giving the XRS Connect controller microphone a neat, professional, factory-look finish. CAT.6 Compliant Fully-Shielded Housing: The fully-shielded, CAT.6 compliant housing with internal supports ensures an extremely stable connection for reliable, trouble-free UHF communication. Red LED Back-Light: The red LED back-light illuminates the switch for clear visibility on the factory dash. Compact 40.5 x 21.3mm Size: The compact adaptor size fits neatly into the factory blank switch location without disrupting the surrounding dash layout. Simple Two-Wire Installation: Connect the red wire to the existing 12V dash light circuit and the black wire to the negative circuit for straightforward fitment. Made in Australia: The XRS-RJ45R3 is manufactured in Australia to GME's quality standards. Compatible with Other 8 Pin RJ45 UHF Radios: Beyond XRS Connect, the adaptor is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Technical Specs Specification Detail SKU XRS-RJ45R3 Brand GME Description RJ45 Pass-Through Adaptor Type 3 (Red) for Nissan LED Colour Red Connector Type 8 Pin RJ45 Housing CAT.6 Compliant, Fully-Shielded Size 40.5 x 21.3mm Wiring 2 Wire (Red - 12V Dash Light Circuit, Black - Negative) Country of Origin Australia Suits XRS Connect UHF CB Radios and Other 8 Pin RJ45 UHF Radios In the Box Adaptor Only Compatible With The XRS-RJ45R3 is compatible with the following Nissan models per GME's compatibility matrix: Patrol GU Series 4-8 (2004-2018), Patrol Y62 (2016-Current), X-Trail T31 (2007-2014), Pathfinder R51 (2005-2012), and Navara NP300 (2016-Current, handbrake console location). It is also compatible with other UHF CB radios using an 8 pin RJ45 connection. Confirm your vehicle model and year against GME's compatibility matrix before purchase. Frequently Asked Questions What does the XRS-RJ45R3 do? The XRS-RJ45R3 lets an XRS Connect controller microphone be integrated into a factory blank switch location on selected Nissan models, giving a neat, factory-look finish instead of a dash-mounted mic. Which Nissan models does it suit? Per GME's compatibility matrix, the XRS-RJ45R3 suits the Patrol GU Series 4-8, Patrol Y62, X-Trail T31, Pathfinder R51, and the Navara NP300 at the handbrake console location. Can it be used with other UHF radios? Yes. Beyond GME's XRS Connect range, the XRS-RJ45R3 is also compatible with other UHF CB radios that use an 8 pin RJ45 connection. How does the red LED back-light work? The red LED back-light is wired via a simple two-wire installation, with the red wire connected to the existing 12V dash light circuit and the black wire to the negative circuit. Is there a white LED version available? Yes. GME also offers the XRS-RJ45W3, the same pass-through adaptor with a white LED back-light instead of red, for the same range of Nissan models. Legendary Products & Support From Authorized Dealers When you choose GME, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized GME dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by GME's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized GME dealer today!

Read more less