Club Series Mono Subwoofer Amplifier from JBL!Compact sizeThe JBL Club A600 amplifier features a low-profile chassis and a small overall footprint to fit in more vehicles where available space is limited.High and low level inputSpeaker-level and low-level inputs allow the Club A600 to integrate with both aftermarket and factory car stereo systems.Variable crossover and bass boostUnlike many amplifiers available at similar prices, the JBL Club A600 features variable electronic crossovers and bass boost circuits allowing for precise system tuning and performance.Low noise and distortionThe Club A600 has been engineered using Balanced Differential Inputs to ensure low noise and distortion even at high output levels. This also makes it far less susceptible to line induced radiated engine noise.Input Level ControlWhen the low-level inputs are used, this control adjusts the input sensitivity between 200mVrms and 2.0 Vrms. When high-level inputs are used, this control adjusts the input sensitivity between 2Vrms and 20Vrms.Full on-board protectionOn-board circuitry protects the Club A600 from shorts, high-temperature, overvoltage and undervoltage. An LED indicator is provided to let you know when one of these conditions exists.Phase SwitchThis switch changes the input phase to inverted or non-inverted. This is especially helpful with the subwoofer channel.RBC wired remoteThe RBC wired remote is an easy installation and can be mounted for convenient volume adjustment from driver's seat.Value engineered car amplifier with JBL power and performanceNew high performance JBL Club amplifiers deliver world class JBL power from a compact chassis built to fit in more vehicles, even when space is tight. Available in 4 channel, 5 channel and mono models. Club amps feature variable crossovers and bass boost for precise control and tuning, plus high and low level inputs that let them integrate with most car stereos. An included wired remote bass level control for Mono and 5 channel that can be mounted for convenient volume adjustment from driver seat.Specifications:Audio Specifications 350 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms) variable low-pass filter (32-320 Hz, 12 dB/octave) variable bass boost (0-12 dB at 45Hz) phase switch (0, 180 degrees) General Specifications Class D amp technology preamp and speaker-level inputs 8-gauge power and ground leads recommended WxHxD=220mm x 51.3mm x 180mm What's in the box: 1 x Club A600 mono subwoofer car amplifier 4 x 30A ATO fuses (2 installed, 2 spare) 2 x Bare wire-to-RCA adapters 1 x Remote bass control module 1 x 16.5‚Ä≤ Remote control cable (RJ-25 plugs on both ends) 2 x Self-tapping screws for remote (M3 x 15mm) 4 x Mounting screws (M4 x 53mm) 2 x JBL stickers 1 x Owner's manual Legendary Products & Support From Authorized Dealers When you choose JBL, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized JBL dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by JBL's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized JBL dealer today!

Read more less

Club Series Mono Subwoofer Amplifier from JBL! JBL's Club A1000 mono subwoofer amplifier can blast your sub with up to 1,000 watts RMS. Its Class D design ensures the amp's high output won't be a burden on your vehicle's electrical system. The package includes a wired remote that lets you control the bass level from the front seat. Features: Mono Amplifier Class D Technology 600W x 1 – RMS 4Œ© 1000W x 1 – RMS 2Œ© Variable Low-Pass Filter Bass Boost Specifications: RMS Power Output (Watts x Channels) 600 x 1 Peak Power Output (Watts x Channels) N/A Power at 2 Ohms (Watts x Channels) 1000 x 1 Bridged Power (Watts x Channels) N/A Minimum Impedance Bridged N/A Minimum Impedance Unbridged 2 Minimum Impedance 2 Best Frequency Response 10-320 Hz THD at Rated RMS Power 1% Signal to Noise Ratio 80 dB Amplifier Class D Low-Pass Crossover Frequency 32-320 Hz Low-Pass Slope (dB/octave) 12 dB/octave High-Pass Crossover Frequency N/A High-Pass Slope (dB/octave) N/A Bass Boost 0-12 dB Bass Boost Frequency 45 Hz Fan Cooled No Fuse Rating 105 Speaker Level Inputs Yes Preamp Outputs No Width (inches) 12-5/8 Height (inches) 2 Depth (inches) 7-3/4 What's in the box: Mono amplifier Six 35-amp ATO fuses (3 installed) 2 Speaker wire to RCA adapters Four 2-1/8‚Ä≥ Screws Two 3/8‚Ä≥ Screws Remote bass controller with 16.5‚Ä≤ Cable attached (RJ25 plug on the end) Adhesive backed JBL logo 2 JBL stickers Owner's manual Legendary Products & Support From Authorized Dealers When you choose JBL, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized JBL dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by JBL's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized JBL dealer today!

Read more less

An Ultra-Compact to Ensure Effortless Installations in the Increasingly Narrow Spaces of Modern Vehicles or in the Factory Amp Area The efficient D Class circuit delivers 600W of maximum power within a compact chassis, an essential requirement for in-car integration. The bass boost function enhances 45Hz up to 12dB to increase subwoofer punch. The double SPEAKER & RCA INPUTS allows the DPower1 to connect to any type of source, be it OEM or aftermarket. For an excellent integration with OEM systems DPower1 is equipped with a smart automated turn on and off circuit according to the factory radio. Legendary Products & Support From Authorized Dealers When you choose HERTZ, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized HERTZ dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by HERTZ's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized HERTZ dealer today!

Read more less

Super Small MonoblockThe new SS amplifiers are the latest in high speed, high current class D designs offering high power and superior sound quality in compact footprints. The classic DD AUDIO style heat sink is used in this upgrade for max cooling with 50% more side wall thickness than industry norms and extra long fins to increase surface area. All major components have been upgraded; higher current mosfets and output devices, increased power capacitors, a more powerful transformer, plus improved venting and PCB with twice the thermal capability.These new high-end mini amps are state of the art, no compromise designs yielding the best sound with unparalleled power to size ratio. The transformation is not only tangible, but audibly apparent.Big clean power from a small package is what the SS600 does best, 600 Watts of continuous power at less than 1% THD+N. Within its chassis you'll discover a selection of the best branded electrical components, 4 layer PCB and large toroidal transformer. Together, these elements synergize to enrich your system with precision and power. For the SS Series the main design focus was to pack as much full-range stereo output capability as possible into as compact of a chassis as possible. We utilized discrete circuit class D technology for ultra low distortion levels that rival class AB designs. The resulting amp is capable of driving multiple driver mid-range and tweeter arrays while consuming less current, taking up less space and delivering more power. Features: High Level Inputs 12dB/Oct High Pass/Low Pass X-Overs Heavyweight DD Aluminum Chassis Set Screw Power and Speaker Terminals Remote Gain Control 4 AWG Power Terminals Specifications: Operating Voltage: 9 - 16 Test Voltage: 14.4 Input Channel(s): 1 Output Channel(s): 1 Continuous Wattage @4ohm: 250 Continuous Wattage @2ohm: 350 Continuous Wattage @1ohm: 600 Max Current Draw (Amps): 60 RCA Input Voltage Sensitivity: 6 - 0.25 High-Level Input Voltage Sensitivity: 20 - 1.1 RCA Input S/N: > 95 Damping Factor: > 100 THD: < 0.1% Bass Boost: 12 Frequency Response (Hz): 20 - 20k Sub-Sonic Filter: 30 - 100 Low-Pass Filter: 35 - 250 Remote Control: Remote Included in Box Power Wire Gauge: 4 Speaker Wire Gauge: 12 Dimensions (Inches): 5.75 x 4.5 x 2 Dimensions (MM): 146 x 115 x 50 Shipping Weight (Lbs): 4 Legendary Products & Support From Authorized Dealers When you choose DD Audio, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized DD Audio dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by DD Audio's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized DD Audio dealer today!

Read more less

Rockford Fosgate T750X1bd Power 750W Class-BD Mono Amplifier High Efficiency, Ultra-Compact, Constant Power Product Overview The Rockford Fosgate T750X1bd is a 750 Watt mono amplifier from the flagship Power series, built on Rockford Fosgate's patented Class-BD technology platform combining the efficiency of Class-D topology with the sonic fidelity of Class-B to deliver 750W mono output in an ultra-compact chassis with significantly lower current draw than a conventional Class A/B amplifier of equivalent output. Designed for the broadest possible vehicle application range hybrid and electric vehicles, small cars, trucks, motorcycles, and side-by-side UTVs the T750X1bd is purpose-engineered for installations where high-output mono performance and compact dimensions are both non-negotiable. Proprietary low-impedance Constant Power technology ensures consistent, predictable output regardless of speaker impedance, and the configurable Molex-style input harness accepts both RCA and speaker-level signals with differential input circuitry that eliminates signal noise from the audio chain. Remote-Out converts the remote input terminal to an output when using speaker-level inputs triggering additional amplifiers without requiring a separate remote source from the vehicle. Real-time Rollback thermal protection, dual fan forced induction, dual extruded heatsinks, C.L.E.A.N. input/output clip detection, on-board Punch EQ, low-pass crossover, PLC2 remote level control compatibility, CEA-2006 and CE compliance, 8 AWG power connectors, upgraded RCA connectors, and discrete surface mount construction complete a mono amplifier built to perform reliably in every environment from marine vessels to electric vehicles. Key Specifications Channels: 1 (mono) Total power: 750W Circuit topology: Class-BD (patented) Constant Power: Yes low impedance Crossover: Built-in low-pass Punch EQ: Built-in patented boost circuit Inputs: Low-level RCA + high-level differential (configurable Molex-style harness) Auto Turn-On: Yes (via high-level input) Remote-Out: Yes (when using high-level inputs) RCA connectors: Upgraded Power connector: 8 AWG Speaker connector: 10 AWG C.L.E.A.N.: Input + output clip detection with LED indicators Thermal protection: Real-time thermal sensing with Rollback technology Cooling: Dual fan forced induction + dual extruded heatsinks + 3-stage thermal lock extrusion Remote level control: PLC2 compatible (sold separately) Control panel: Top-mounted Construction: Discrete surface mount technology CEA-2006 compliant: Yes CE compliant: Yes Rated power: Confirm with supplier Dimensions: Confirm with supplier Shipping weight: Confirm with supplier Features & Benefits Rockford Fosgate patented Class-BD technology: Class-BD combines Class-D switching efficiency with Class-B topology fidelity delivering high-efficiency mono output that draws significantly less current from the vehicle's charging system than a Class A/B amplifier of equivalent output, while maintaining the sonic accuracy associated with Class-B operation. A genuine advantage in vehicles with limited alternator capacity hybrid and electric vehicles, motorcycles, small cars, and UTVs where electrical system load management is a real constraint. Proprietary low-impedance Constant Power: Delivers consistent output across low impedance loads, ensuring predictable performance and maximising power delivery to the connected subwoofer regardless of impedance variation consistent with the Constant Power technology across the T-series and TM-series range. 750W mono in an ultra-compact chassis: High-output mono performance in a compact form factor designed for the restricted installation spaces of motorcycles, UTVs, small cars, and behind-dash vehicle locations where standard mono amplifier chassis dimensions create fitment challenges. Configurable Molex-style input harness RCA and speaker-level in one connector: The Molex-style harness accepts both low-level RCA and high-level speaker-level signals through the same configurable connector simplifying installation and reducing cable clutter compared to amplifiers requiring separate wiring runs for each input type. Suitable for factory OEM integration and aftermarket head unit connection from the same amplifier. Differential input circuitry for noise-free signal: Differential inputs reject common-mode noise and ground loop interference that standard single-ended inputs pass through to the audio signal particularly important in hybrid and electric vehicles where high-voltage electrical architecture commonly introduces interference. Also valuable in motorcycles and UTVs where long signal cable runs from dash to amplifier increase noise pickup. Remote-Out feature: When using high-level inputs, the remote input terminal converts to an output signal that triggers additional amplifiers or accessories eliminating the need to source a separate remote turn-on from the vehicle's electrical system. Particularly useful in factory OEM integrations where a dedicated remote wire is unavailable. Real-time thermal sensing with Rollback technology: Progressively reduces output power as temperatures approach the threshold rather than shutting down completely maintaining audio at a reduced level in extreme thermal conditions. Consistent with the TM500X1br and T1000X5ad in this catalogue a critical feature for UTV, motorcycle, and summer Australian installations. Dual fan forced induction with 3-stage thermal lock extrusion and dual extruded heatsinks: Active forced air cooling combined with a multi-stage passive heatsink provides comprehensive thermal management for 750W mono output in the compact chassis required for Element Ready vehicle applications. C.L.E.A.N. input and output clip detection with LED indicators: Simultaneous input and output THD monitoring for accurate gain structure setup and ongoing clip detection consistent with the Power series standard across this catalogue. Built-in low-pass crossover and Punch EQ boost circuit: On-board crossover and bass boost without external processors practical for compact installations where signal processor space is unavailable. Upgraded RCA connectors: Higher-quality connectors reducing signal degradation and improving long-term reliability in high-vibration UTV, motorcycle, and truck installations. 8 AWG power and 10 AWG speaker connectors: Appropriate wiring gauge connectors for the current demands of a 750W mono amplifier consistent with the TM500X1br specification in this catalogue. PLC2 remote level control compatible: Optional Rockford Fosgate PLC2 for dash-mounted subwoofer output level control with input clip indicator. Sold separately. CEA-2006 and CE compliant: Power ratings verified against the CEA-2006 industry standard. CE compliance confirms European safety and EMC conformity both are verified, comparable specifications. Discrete surface mount technology construction: Compact, vibration-resistant circuit board assembly contributing to both the ultra-compact chassis and long-term reliability in high-vibration motorcycle, UTV, and off-road installations. Technical Specs Specification Detail SKU T750X1bd Brand Rockford Fosgate Number of Channels 1 (mono) Total Power 750W Circuit Topology Class-BD (patented) Constant Power Yes low impedance Crossover Built-in low-pass Punch EQ Built-in patented boost circuit Signal Input Low-level RCA + high-level differential (Molex-style harness) Auto Turn-On Yes (via high-level input) Remote-Out Yes (when using high-level inputs) RCA Connectors Upgraded Power Connector 8 AWG Speaker Connector 10 AWG C.L.E.A.N. Input + output clip detection with LED indicators Thermal Protection Real-time thermal sensing with Rollback technology Cooling Dual fan forced induction + dual extruded heatsinks + 3-stage thermal lock extrusion Remote Level Control PLC2 compatible (sold separately) Control Panel Top-mounted Construction Discrete surface mount technology CEA-2006 Compliant Yes CE Compliant Yes Rated Power Confirm with supplier Dimensions Confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Hybrid and electric vehicles requiring OEM integration with noise-rejecting differential inputs Motorcycles, UTVs, side-by-sides, and powersport vehicles requiring compact 750W mono amplification Small cars, trucks, and vehicles with restricted amplifier installation space Factory and aftermarket head units with RCA or high-level outputs Rockford Fosgate Power and Punch series subwoofers rated for 750W mono input Downstream amplifiers triggered via Remote-Out in multi-amplifier system builds Optional Rockford Fosgate PLC2 Punch Level Control (sold separately) Vehicles where Class-BD current efficiency reduces alternator and battery system load Frequently Asked Questions What is Class-BD technology and how does it differ from Class-D and Class A/B? Class-BD is Rockford Fosgate's patented topology that combines Class-D switching efficiency with Class-B topology fidelity. Class-D alone delivers high efficiency but can introduce switching artefacts; Class A/B delivers sonic accuracy but at lower efficiency and higher current draw. Class-BD achieves both drawing significantly less current than a Class A/B amplifier of equivalent output while maintaining the sonic quality associated with Class-B operation. How does the Molex-style input harness work? The configurable Molex-style connector accepts both low-level RCA and high-level speaker-level signals through the same harness eliminating the need for separate wiring configurations depending on the source. This simplifies installation in OEM integration scenarios and reduces cable management complexity in confined installation spaces. What does the Remote-Out feature do? When the T750X1bd is connected via high-level inputs, the remote input terminal converts to an output that triggers additional amplifiers or accessories. This eliminates the need to source a separate remote turn-on signal from the vehicle particularly useful in hybrid, electric, and OEM factory system integrations where a dedicated remote wire is unavailable. How does the T750X1bd differ from the TM500X1br Power Marine mono amplifier? Both are compact mono amplifiers with Rollback thermal protection, dual fan cooling, C.L.E.A.N. I/O, and Remote-Out. The T750X1bd uses Class-BD technology and delivers 750W, while the TM500X1br uses Class-BR (Boosted Rail) technology and delivers 500W. The TM500X1br has marine-grade conformal PCB coating for permanent marine installation; the T750X1bd is designed for the broadest vehicle application range including hybrid, electric, UTV, and motorcycle. Choose based on your primary installation environment and power requirement. Is a remote level control included with the T750X1bd? No. The optional PLC2 Punch Level Control is sold separately and connects to the dedicated remote control input for subwoofer output level adjustment with input clip indicator from a convenient dash or mounting location. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate T500-1BDCP — Constant Power. Every Ohm. No Compromise. Product Overview The Rockford Fosgate T500-1BDCP is a Power Series Class-bd mono amplifier built on the foundation of the legendary T500-1bd, elevated with a proprietary Constant Power configuration that delivers up to 25% more output across all impedance loads compared to a conventional amplifier at the same rated wattage. Where a standard amplifier loses power as impedance rises, the T500-1BDCP maintains consistent output giving you more usable watts whether you're running 1-ohm, 2-ohm, or 4-ohm subwoofer loads. Its frequency response is optimised exclusively for subwoofer use this is a dedicated bass amplifier, not a general-purpose mono. The MOSFET power supply and MOSFET output stage deliver tight, controlled, low-distortion bass reproduction at sustained levels, while 4-gauge power and ground connectors and audiophile-grade speaker terminals ensure the signal and current path live up to the amplifier's output capability. The infrasonic filter protects your subwoofer from damaging sub-audible frequencies, and RCA pass-thru outputs keep multi-amp builds clean and Y-adapter free. Key Specifications Total RMS Output: 500 watts mono Amplifier Class: Class-bd Constant Power: Yes — up to 25% more power across all impedance loads Frequency Response: Optimised for subwoofer use only Crossover: 24dB/octave Infrasonic Filter: Yes Power Supply: MOSFET Output Stage: MOSFET Power/Ground Connectors: 4 AWG Speaker Connections: Audiophile-grade RCA Pass-Thru Outputs: Yes Subwoofer Compatibility: Two 4-ohm DVC subwoofers (under-seat configuration confirmed by manufacturer) Features & Benefits Constant Power Configuration — Rockford Fosgate's proprietary Constant Power design maintains up to 25% more wattage across all impedance loads compared to a conventional amplifier. A standard amp rated at 500W at 1 ohm drops output significantly at 2 or 4 ohms — the T500-1BDCP holds its output consistent. This translates directly to more headroom, more dynamic range, and more bass impact from the same amplifier. Subwoofer-Optimised Frequency Response — The T500-1BDCP's signal path and tuning are engineered exclusively for low-frequency reproduction. This isn't a compromise — it's a design decision that produces tighter, more controlled bass than a general-purpose mono amplifier of equivalent wattage. MOSFET Power Supply — Metal-Oxide-Semiconductor Field-Effect Transistor power supply design delivers stable, efficient current conversion with low noise — the foundation of clean, dynamic bass output at sustained listening levels. MOSFET Output Stage — MOSFET output devices offer fast switching, low distortion, and excellent thermal characteristics under sustained bass loads. The result is bass that stays controlled and defined even when pushed hard. 24dB/Octave Crossover — Steeper than the 12dB/octave Butterworth found in the Punch series, the 24dB/octave crossover provides a sharper roll-off at the crossover point — more aggressive filtering that keeps high-frequency content away from the subwoofer and improves system integration. Infrasonic Filter — Removes sub-audible frequencies that cause excessive cone excursion without producing usable bass. Essential for ported enclosures and low-tuned sealed boxes — protects driver longevity and keeps your output clean during heavy bass passages. 4 AWG Power/Ground Connectors — Heavier gauge than the 8 AWG found on compact or entry-level monoblocks. Larger conductor cross-section reduces resistance in the power delivery path, ensuring the amplifier receives the current it needs for sustained high-output performance. Audiophile-Grade Speaker Connections — Higher-quality speaker terminals reduce contact resistance and provide a more secure mechanical connection than standard push-type connectors — important for high-current, low-impedance subwoofer loads. RCA Pass-Thru Outputs — Chain a second amplifier for front/rear speakers without Y-adapters or returning to the head unit. Keeps signal integrity intact and simplifies wiring in multi-amp builds. Under-Seat Subwoofer Amplifier Capability — Manufacturer-confirmed compatibility with two 4-ohm DVC subwoofers in an under-seat configuration — practical for utes, SUVs, and vehicles where boot space is dedicated to cargo rather than audio. Technical Specs Specification Detail Total RMS Power 500W mono Amplifier Class Class-bd Constant Power Yes — up to 25% more across all impedance loads Application Subwoofer use only Crossover 24dB/octave Infrasonic Filter Yes Power Supply MOSFET Output Stage MOSFET Power Connector 4 AWG Ground Connector 4 AWG Speaker Connections Audiophile-grade RCA Pass-Thru Outputs Yes Subwoofer Configuration Two 4-ohm DVC (under-seat — manufacturer confirmed) Input Type Not specified — confirm with supplier Auto Turn-On Not specified — confirm with supplier Remote Level Control Not specified — confirm with supplier Dimensions Not specified Weight Not specified Signal-to-Noise Ratio Not specified THD Not specified Minimum Impedance Not specified — confirm with supplier Frequency Response Not specified (subwoofer-optimised — confirm range) Input Sensitivity Not specified Compatible With / Goes Well With Subwoofer Configurations: Two 4-ohm DVC subwoofers (under-seat configuration — manufacturer confirmed) Single subwoofer builds (impedance to be confirmed with supplier) System Integration: Multi-amp builds via RCA pass-thru (no Y-adapters required) Under-seat dedicated subwoofer installations (utes, SUVs, wagons) Accessories: 4 AWG power/ground wiring kit (required — confirm rated kit with supplier) Audiophile-grade speaker cable (matched to terminal quality) Frequently Asked Questions What does Constant Power mean and why does it matter for subwoofer performance? Constant Power means the T500-1BDCP delivers up to 25% more watts across all impedance loads compared to a conventional amplifier at the same rating — so your subwoofer receives consistent, sustained output regardless of impedance, resulting in tighter and more dynamic bass. Can the T500-1BDCP drive two subwoofers at once? Yes. Rockford Fosgate confirms the T500-1BDCP is capable of driving two 4-ohm DVC subwoofers — including in an under-seat configuration — making it a practical choice for utes, SUVs, and vehicles where boot space is at a premium. Why does this amplifier have a 24dB/octave crossover instead of the more common 12dB/octave? A 24dB/octave crossover rolls off frequencies more steeply above the crossover point — keeping unwanted mid-range content away from the subwoofer more effectively. This produces cleaner integration between your subwoofer and main speakers. What is the infrasonic filter and do I need it? The infrasonic filter removes sub-audible frequencies that cause excessive cone movement without producing usable bass. It's particularly important for ported enclosures and is strongly recommended for any subwoofer installation to protect driver longevity. What gauge power and ground wiring does the T500-1BDCP require? The T500-1BDCP uses 4 AWG power and ground connectors — heavier than the 8 AWG found on many compact mono amplifiers. Use a quality 4 AWG wiring kit to ensure the amplifier receives the current needed for sustained high-output performance. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

2,500 Watts, Dual-Amp PowerSync, and MasterSync Control Rockford Fosgate's Flagship Class-BD Constant Power Mono Amplifier. Product Overview The Rockford Fosgate Power T2500-1BDCP is a 2,500W mono amplifier that steps beyond the T1500-1BDCP with two features absent from the lower-wattage models: PowerSync and MasterSync. PowerSync allows two T2500-1BDCP units to be bridged together, delivering a combined 5,000W from a single synchronised pair. MasterSync extends this further one amplifier acts as the master controller for an array of T2500-1BDCP amplifiers, enabling large-format multi-amplifier installations for competition and extreme high-output builds. The core Constant Power, Class-BD, and MOSFET platform is shared with the T1000-1BDCP and T1500-1BDCP adding 1/0 AWG (rather than 4-gauge) power and ground connectors to match the higher current demands of a 2,500W amplifier, a 0°/180° phase switch for precise subwoofer-to-system integration, and blue LED simulated VU signal and power meters for real-time output monitoring. A 24dB/octave crossover, infrasonic filter, and RCA pass-thru complete the subwoofer-dedicated control set. Key Specifications Power output: 2,500W (mono — rated power at specific impedance not confirmed — see Red-flags) Amplifier class: Class-BD Configuration: Monoblock (subwoofer dedicated) Constant Power technology: Yes — up to 25% more power across all impedance loads (supplier-stated) PowerSync: Yes — 2 amplifiers bridged for combined 5,000W output MasterSync: Yes — 1 amplifier controls an array of amplifiers Crossover: 24dB/octave Infrasonic filter: Yes Phase switch: 0°/180° Power supply: MOSFET Output stage: MOSFET Speaker connections: Audiophile grade Power/ground connectors: 1/0 AWG RCA pass-thru outputs: Yes LED meters: Blue LED simulated VU signal and power meters Frequency response: Subwoofer optimised (specific Hz range not confirmed) Signal-to-noise ratio: Not specified — confirm with Rockford Fosgate THD: Not specified — confirm with Rockford Fosgate Input voltage range: Not specified — confirm with Rockford Fosgate Dimensions: Not specified — confirm with Rockford Fosgate Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits PowerSync — Two Amplifiers, One Combined 2,500W Output — Two T2500-1BDCP amplifiers in PowerSync mode operate as a single synchronised unit, delivering a combined 5,000W. For installations where a single 2,500W amplifier falls short of the subwoofer system's demands, PowerSync provides a clean, factory-supported solution — no external bridging issues or incompatibility risks. MasterSync — Array Control for Multi-Amplifier Builds — In MasterSync configuration, one T2500-1BDCP acts as the master unit and controls the volume and settings of an array of additional amplifiers. This enables large-format high-output installations — competition SPL vehicles, extreme builds — to be managed coherently from a single control point. 1/0 AWG Power and Ground Connectors — Stepping up from the 4-gauge connectors on the 1,000W and 1,500W models, the T2500-1BDCP takes 1/0 AWG (approximately 53mm²) wiring — matching the substantially higher current demands of a 2,500W amplifier. Proper 1/0 AWG wiring is essential to prevent voltage drop and power delivery limitations at full output. 0°/180° Phase Switch — Allows the subwoofer output to be switched between in-phase and out-of-phase relative to the main speakers, enabling precise time-alignment and acoustic integration in complex multi-driver subwoofer systems or when compensating for enclosure placement. Blue LED Simulated VU Signal and Power Meters — Real-time visual feedback of signal level and output power — allowing gain structure optimisation during system setup and providing a visual indication of output activity during use. Constant Power Technology — Up to 25% More Power Across All Impedance Loads — The same Constant Power platform as the T1000-1BDCP and T1500-1BDCP, applied here to 2,500W — maintaining maximum output more consistently across 1Ω, 2Ω, and 4Ω loads than a standard amplifier design. (Supplier-stated performance claim.) Class-BD Topology — Rockford Fosgate's proprietary Class-BD delivers high-current efficiency for subwoofer loads, combining characteristics of Class-B/AB and Class-D. MOSFET Power Supply and Output Stage — Dual MOSFET implementation provides the fast switching speed and thermal stability needed for sustained 2,500W operation. 24dB/Octave Crossover — Steep crossover slope tightly limits the subwoofer frequency band for clean integration in multi-amplifier car audio systems. Infrasonic Filter — At 2,500W, removing inaudible sub-20Hz content that could over-excite subwoofer cone excursion is particularly important for driver protection. RCA Pass-Thru Outputs — Signal looping for downstream amplifiers in multi-amp builds. Technical Specs Specification Detail Brand Rockford Fosgate Part Number T2500-1BDCP Series Power Power Output 2,500W Amplifier Class Class-BD Configuration Monoblock Application Subwoofer Dedicated Constant Power Yes — up to 25% more across all impedance loads (supplier-stated) PowerSync Yes — 2 amps = combined 5,000W MasterSync Yes — 1 amp controls array Crossover 24dB/Octave Infrasonic Filter Yes Phase Switch 0° / 180° Power Supply MOSFET Output Stage MOSFET Speaker Connections Audiophile Grade Power/Ground Connectors 1/0 AWG RCA Pass-Thru Yes LED Meters Blue LED Simulated VU Signal and Power Meters Rated Power (per impedance) Not specified — confirm with Rockford Fosgate Frequency Response Subwoofer optimised — Hz range not specified Signal-to-Noise Ratio Not specified THD Not specified Input Voltage Range Not specified Dimensions Not specified Weight Not specified Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable subwoofer configurations: Single or multiple subwoofer setups requiring a high-output dedicated mono amplifier 1Ω, 2Ω, and 4Ω impedance loads (confirm RMS power per impedance with Rockford Fosgate) High-efficiency ported, sealed, and bandpass subwoofer enclosures Competition SPL and extreme high-output car audio builds Dual-amplifier builds using PowerSync (2× T2500-1BDCP = 5,000W combined) Choosing between T1000, T1500, and T2500: T1000-1BDCP (1,000W): Suited to most quality subwoofer builds and daily use systems T1500-1BDCP (1,500W): Larger subwoofers, dual-sub builds, high-efficiency ported enclosures T2500-1BDCP (2,500W): Competition and extreme builds; PowerSync and MasterSync for multi-amp systems Pairs well with: A second T2500-1BDCP (PowerSync for 5,000W combined) 1/0 AWG amplifier wiring kits Rockford Fosgate Power series T2 and T3 subwoofers Rockford Fosgate or aftermarket RCA signal cables Frequently Asked Questions What does PowerSync allow the T2500-1BDCP to do? PowerSync allows two T2500-1BDCP amplifiers to be electronically bridged together and operate as a single synchronised unit, combining their output for a total of 5,000W. This is a factory-supported configuration — confirm specific wiring and impedance requirements for PowerSync operation with Rockford Fosgate or your authorised installer. What is MasterSync and when would I use it? MasterSync designates one T2500-1BDCP as a master controller for an array of T2500-1BDCP amplifiers. Volume and settings are controlled from the master unit, coordinating multiple amplifiers in large-format installations — competition vehicles, extreme builds, or installations with multiple subwoofer arrays requiring unified control. Why does the T2500-1BDCP require 1/0 AWG wiring when the T1000 and T1500 use 4-gauge? A 2,500W amplifier draws substantially more current than a 1,000W or 1,500W amplifier. 1/0 AWG cable (approximately 53mm²) has significantly lower resistance and higher current carrying capacity than 4-gauge — essential for preventing voltage drop, maintaining full power delivery, and protecting the wiring from overheating at the T2500-1BDCP's peak current draw. What does the 0°/180° phase switch do? The phase switch allows the subwoofer's acoustic output to be inverted 180° relative to the main speakers. This compensates for acoustic cancellation that can occur when a subwoofer is positioned out of phase with the main speakers — either due to enclosure placement, vehicle acoustics, or driver polarity — ensuring maximum bass output at the listening position. What is the difference between the T2500-1BDCP and the T1500-1BDCP? The T2500-1BDCP delivers 2,500W versus the T1500's 1,500W, and adds PowerSync (two-amp bridging for 5,000W), MasterSync (array control), a 0°/180° phase switch, blue LED VU meters, and 1/0 AWG wiring connectors. The T1500-1BDCP uses 4-gauge connectors and does not include these features. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Unleash Unmatched Power: Orion 1000W Max XTR Series Class D Monoblock Amplifier for Audiophile Experience! Orion 1000W max XTR series class D monoblock high-performance car audio amplifier.  Specifications: RMS Power Rating: 4 ohms: 125 watts x 1 chan. / 2 ohms: 250 watts x 1 chan. / 1 ohm: 500 watts x 1 chan. Max power output: 1000 watts x 1 chan. Classic Orion industrial design MOSFET power supply Wired remote bass level control included Tuned Bass EQ (0-18 dB bass boost at 45 Hz) IntelliQ Bass optimization circuit Single channel monoblock operation 1 Pair of preamp RCA outputs Master/Copy switch for slave and master control Heavy duty aluminum alloy heatsink for optimal heat dissipation Nickel-plated RCA level inputs Nickel-plated screw terminals Variable low-pass filter (30-250 Hz, 12 dB/octave) Phase control switch Gain adjustment Subsonic Filter CEA-2006 compliant amplifier Frequency response: 30-250 Hz Dimensions: 9-1/2‚Ä≥D x 10-7/8‚Ä≥W x 2-5/8‚Ä≥H Legendary Products & Support From Authorized Dealers When you choose Orion, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Orion dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Orion's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Orion dealer today!

Read more less

Designed to Be a True Worldwide Product! Orion 1400W RMS XTR series class D monoblock amplifier. Specifications: RMS Power Rating: ¢ 4 ohms: 550 watts x 1 chan. ¢ 2 ohms: 900 watts x 1 chan. ¢ 1 ohm: 1400 watts x 1 chan. Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Variable Bass Boost (0 to +18 dB bass boost) Soft start turn-on Mono channel operation Preamp RCA outputs to daisy chain multiple amps 4-way protection circuitry (thermal, DC offset, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: Level: 200mV-8V Variable low-pass filter (15-250 Hz, 24 dB/octave) Selectable subsonic filter (25 Hz, 12 dB) CEA-2006 compliant amplifier 4 gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Dimensions: 11-1/2"W x 9-15/16"L x 2-1/2"H Legendary Products & Support From Authorized Dealers When you choose Orion, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Orion dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Orion's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Orion dealer today!

Read more less

Creates a Full-On Sound That Draws People In! If you need some bass power but your wallet's a little weak, check out the JBL Audio Stage A3001 subwoofer amplifier. This potent little JBL amp sends up to 300 watts RMS to your sub, making your drive more exciting as it fills your ride with low-frequency punch. Speaker-level inputs allow this amplifier to work with most systems, even if you're keeping your factory radio. The built-in low-pass filter, variable bass boost, and phase adjustment maximize your system's performance. No matter what you listen to, the JBL Audio Stage A3001 will deliver the clean bass that makes your music come alive in your car. Features: Mono subwoofer amplifier 300 watts RMS x 1 at 2 ohms (4-ohm rating unavailable) Variable low-pass filter (32-320 Hz, 12 dB/octave) Variable bass boost (0-12 dB at 40-100 Hz) Variable phase adjustment (0-180¬∞) Preamp and speaker-level inputs Fuse rating: 15A x 2 Wiring and hardware not included with amplifier (8-gauge power and ground leads recommended) 9-9/16‚Ä≥W x 2‚Ä≥H x 5-3/4‚Ä≥D What's in the Box: 1 x Amplifier 1 x Spare fuse (x2 for 1-channel and 4-channel model) 1 x Quick start guide 1 x High-level input cable (x2 for 4-channel model). 2 x Two-color JBL brand stickers Legendary Products & Support From Authorized Dealers When you choose JBL, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized JBL dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by JBL's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized JBL dealer today!

Read more less

Rockford Fosgate R2-750X1 Prime 750 Watt Mono Class-D Subwoofer Amplifier A 750W mono Class-D subwoofer amplifier rated at 750W x 1 at 1-ohm, 500W x 1 at 2-ohm, and 250W x 1 at 4-ohm (CTA-2006 rated). Features Continuously Variable Punch EQ with up to 18dB of bass boost at 45Hz, variable infrasonic filter, C.L.E.A.N. gain calibration, RCA pass-through outputs, RLC remote level control, Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management. Designed and engineered in Tempe, Arizona. Backed by a 1 year warranty. Product Overview The Rockford Fosgate R2-750X1 is a 750W mono Class-D subwoofer amplifier from the Prime R2 series, designed for car audio builds requiring dedicated subwoofer amplification at a strong price-to-performance ratio. As a dedicated single-channel subwoofer amplifier, it operates across a frequency range of 20Hz-250Hz. Rated continuous power is 250W x 1 at 4-ohm, 500W x 1 at 2-ohm, and 750W x 1 at 1-ohm (CTA-2006, less than 1.0% THD+N). Dynamic power via PowerCube reaches 300W at 4-ohm, 545W at 2-ohm, and 830W at 1-ohm. The Continuously Variable onboard Punch EQ delivers up to 18dB of boost at 45Hz. The variable infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing adjustable protection for different subwoofer drivers and enclosure types. RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a second amplifier without degradation. An RLC remote level control is included for in-cabin subwoofer volume adjustment. High-level inputs (450mV-12V) allow direct integration with OEM head units without RCA outputs. Auto-Sense turn-on via high-level input is supported, with an Auto-Sense bypass switch for vehicles with Retained Accessory Power (RAP) systems. C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) input and output clip indicators guide precise gain calibration at setup. Rollback Protection dynamically manages output to prevent thermal stress on the output devices. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. MEHSA4 reduces MOSFET temperatures, lowers distortion, and extends output device life. Cast aluminium heatsink with convection cooling. Designed and engineered in Tempe, Arizona. Features & Benefits 750W at 1-Ohm - Maximum Subwoofer Output: The R2-750X1 delivers its maximum rated output of 750W at 1-ohm (830W dynamic), with stepped output of 500W at 2-ohm and 250W at 4-ohm, providing flexibility to match a wide range of subwoofer impedance configurations. Continuously Variable Punch EQ - Up to 18dB at 45Hz: The onboard Punch EQ provides up to 18dB of continuously adjustable bass boost at 45Hz, allowing subwoofer output to be tuned to the acoustic characteristics of the installation without a separate equaliser. Variable Infrasonic Filter - 15Hz to 40Hz Tunable: The infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing flexible protection for different subwoofer drivers and enclosure types beyond what a fixed infrasonic filter can offer. RCA Pass-Through Outputs - Downstream Chaining: RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a downstream speaker amplifier such as the R2-750X5 without Y-cable noise. C.L.E.A.N. Technology - Precise Gain Calibration: C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) provides dedicated input and output clip indicator LEDs for precise gain calibration at setup, maximising output while minimising distortion. RLC Remote Level Control Included: An RLC remote level control is included for in-cabin subwoofer volume adjustment without returning to the amplifier. Rollback Protection and NOMAD Speaker Protection: Rollback Protection dynamically manages output during sustained high-output conditions to prevent thermal stress on the output devices. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. High-Level OEM Input with Auto-Sense Turn-On: High-level inputs accept OEM head unit speaker outputs, with Auto-Sense activating the amplifier automatically when a signal is detected. A bypass switch is included for vehicles with RAP systems. Technical Specs Specification Detail SKU R2-750X1 Number of Channels 1 (Monoblock) Total Power 750W Rated Power - 4-ohm (CTA-2006, less than 1.0% THD+N) 250W x 1 Rated Power - 2-ohm (CTA-2006, less than 1.0% THD+N) 500W x 1 Rated Power - 1-ohm (CTA-2006, less than 1.0% THD+N) 750W x 1 Dynamic Power - 4-ohm (PowerCube) 300W x 1 Dynamic Power - 2-ohm (PowerCube) 545W x 1 Dynamic Power - 1-ohm (PowerCube) 830W x 1 Circuit Topology Class-D Bridgeable No Frequency Response 20 Hz - 250 Hz THD + Noise Less than 1.0% at 4-ohm, 2-ohm, and 1-ohm Input Sensitivity Low-Level: 150mV - 4V / High-Level: 450mV - 12V Signal Input 2 x RCA / 4-Pin Molex High-Level Signal Output 2 x RCA Pass-Thru (active with RCA or High-Level input) Tone Controls Punch EQ: 0 to +18dB at 45Hz (Continuously Variable) Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Infrasonic Filter 15 Hz - 40 Hz at 12dB/Octave Butterworth (Variable) Remote Controls Yes (RLC Remote Level Control included) Auto-Sense Turn-On Yes (with RAP bypass switch) Power Wire Gauge 4 AWG Power Input Connector Compression Terminal Block Speaker Wire Gauge 8 AWG Speaker Output Connector Compression Terminal Block Cooling Convection Heatsink Cast Aluminium Operating Voltage 9 - 16 VDC Recommended Fuse (not included) 120A Max Current Draw at 13.8V Sinewave 71A Visual Indicators Power: Blue / Protect: Red / C.L.E.A.N. In: Red / C.L.E.A.N. Out: Blue/Red Dimensions (H x W x D) 49 x 173 x 255mm (1.9 x 6.8 x 10.1 inch) CTA-2006 Compliant Yes Warranty 1 Year Compatible With / Goes Well With The R2-750X1 suits car audio builds requiring a dedicated mono subwoofer amplifier at the Prime R2 price point. It pairs naturally with the R2-750X5 via its RCA pass-through outputs for a complete 5-channel plus dedicated mono system. Goes Well With: R2-2X12 / R2-2X10 - Rockford Fosgate Prime dual loaded subwoofer enclosures, a direct application pairing with the R2-750X1 at 2-ohm R2D2-12 / R2D2-10 - Prime R2 series individual subwoofers for custom enclosure builds R2-750X5 - Companion R2 series 5-channel amplifier for speaker amplification, chainable via the R2-750X1's RCA pass-through outputs RFK4 - Rockford Fosgate 4 AWG amplifier wiring kit to complete the installation DSR1 - Rockford Fosgate Digital Signal Processor for advanced signal processing ahead of the R2-750X1 Frequently Asked Questions What impedance gives the most power from the R2-750X1? The R2-750X1 delivers maximum rated output at 1-ohm (750W RMS, 830W dynamic). At 2-ohm the output is 500W RMS, and at 4-ohm it is 250W RMS. For maximum subwoofer output, a subwoofer or dual subwoofer configuration wired to a 1-ohm or 2-ohm total load is recommended. Contact us for advice on matching your subwoofer configuration to the correct impedance setting. What is the difference between the R2-750X1 and the R2-750X5? The R2-750X1 is a monoblock subwoofer amplifier with a single Class-D channel operating from 20Hz-250Hz, delivering up to 750W RMS at 1-ohm. The R2-750X5 is a 5-channel Full-Range Class-D amplifier delivering 100W x 4 plus 350W x 1 at 2-ohm, designed to power both speakers and a subwoofer from the one unit. In most builds, both are used together - the R2-750X5 for speakers and the R2-750X1 for the subwoofer, connected via the R2-750X1's RCA pass-through outputs. Can the R2-750X1 be used with a factory OEM head unit? Yes. The R2-750X1 includes high-level inputs (450mV-12V) for direct connection to OEM head unit speaker outputs without RCA outputs. Auto-Sense turn-on activates the amplifier automatically when a signal is detected on the high-level input, removing the need for a dedicated remote wire. A RAP bypass switch is also included. What fuse does the R2-750X1 require and is it included? The R2-750X1 requires a 120A fuse, which is not included and must be sourced separately. Install the fuse as close to the battery as possible in the 4 AWG power supply line. Does the R2-750X1 work with a dual voice coil subwoofer? Yes. A dual voice coil (DVC) subwoofer can be wired in parallel to achieve a 1-ohm or 2-ohm load depending on the coil impedance, allowing you to take advantage of the R2-750X1's maximum output at 1-ohm. Contact us for advice on the correct wiring configuration for your specific subwoofer. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate R2-500X1 Prime 500 Watt Mono Class-D Subwoofer Amplifier A 500W mono Class-D subwoofer amplifier rated at 500W x 1 at 2-ohm and 300W x 1 at 4-ohm (CTA-2006 rated). Features Continuously Variable Punch EQ with up to 18dB of bass boost at 45Hz, variable infrasonic filter, C.L.E.A.N. gain calibration, RCA pass-through outputs, RLC remote level control, Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management. Designed and engineered in Tempe, Arizona. Backed by a 1 year warranty. Product Overview The Rockford Fosgate R2-500X1 is a 500W mono Class-D subwoofer amplifier from the Prime R2 series, designed for car audio builds requiring dedicated subwoofer amplification at a strong price-to-performance ratio. As a dedicated single-channel subwoofer amplifier, it operates across a frequency range of 20Hz-250Hz. Rated continuous power is 300W x 1 at 4-ohm and 500W x 1 at 2-ohm (CTA-2006, less than 1.0% THD+N). Dynamic power via PowerCube reaches 350W at 4-ohm and 590W at 2-ohm. Unlike the R2-750X1 which is also 1-ohm stable, the R2-500X1 operates at 4-ohm or 2-ohm only. The Continuously Variable onboard Punch EQ delivers up to 18dB of boost at 45Hz. The variable infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing flexible protection for different subwoofer drivers and enclosure types. RCA pass-through outputs allow the signal to be chained to a companion speaker amplifier. An RLC remote level control is included for in-cabin subwoofer volume adjustment. High-level inputs (450mV-12V) allow direct integration with OEM head units without RCA outputs. Auto-Sense turn-on activates the amplifier automatically when a signal is detected, with a bypass switch for vehicles with Retained Accessory Power (RAP) systems. C.L.E.A.N. input and output clip indicators guide precise gain calibration. Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management are all active. Cast aluminium heatsink with convection cooling. Designed and engineered in Tempe, Arizona. Features & Benefits 500W at 2-Ohm - High Output Mono Subwoofer Performance: The R2-500X1 delivers 500W RMS at 2-ohm (590W dynamic) and 300W RMS at 4-ohm, providing substantial subwoofer output for the Prime R2 price point. Continuously Variable Punch EQ - Up to 18dB at 45Hz: The onboard Punch EQ provides up to 18dB of continuously adjustable bass boost at 45Hz, allowing subwoofer output to be tuned to the acoustic characteristics of the installation without a separate equaliser. Variable Infrasonic Filter - 15Hz to 40Hz Tunable: The infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing flexible and adjustable protection for different subwoofer drivers and enclosure types. RCA Pass-Through Outputs - Downstream Chaining: RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a downstream speaker amplifier such as the R2-500X4 without Y-cable noise or signal degradation. C.L.E.A.N. Technology - Precise Gain Calibration: C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) provides dedicated input and output clip indicator LEDs for precise gain calibration at setup, maximising output while minimising distortion. RLC Remote Level Control Included: An RLC remote level control is included for in-cabin subwoofer volume adjustment without returning to the amplifier. Rollback Protection and NOMAD Speaker Protection: Rollback Protection dynamically manages output during sustained high-output conditions to prevent thermal stress on the output devices. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. Auto-Sense Turn-On with RAP Bypass: Auto-Sense activates the amplifier automatically when a high-level input signal is detected, removing the need for a dedicated remote turn-on wire. A bypass switch is included for vehicles with RAP systems. Technical Specs Specification Detail SKU R2-500X1 Number of Channels 1 (Monoblock) Total Power 500W Rated Power - 4-ohm (CTA-2006, less than 1.0% THD+N) 300W x 1 Rated Power - 2-ohm (CTA-2006, less than 1.0% THD+N) 500W x 1 Dynamic Power - 4-ohm (PowerCube) 350W x 1 Dynamic Power - 2-ohm (PowerCube) 590W x 1 Circuit Topology Class-D Bridgeable No Frequency Response 20 Hz - 250 Hz THD + Noise Less than 1.0% at 4-ohm and 2-ohm Input Sensitivity Low-Level: 150mV - 4V / High-Level: 450mV - 12V Signal Input 2 x RCA / 4-Pin Molex High-Level Signal Output 2 x RCA Pass-Thru (active with RCA or High-Level input) Tone Controls Punch EQ: 0 to +18dB at 45Hz (Continuously Variable) Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Infrasonic Filter 15 Hz - 40 Hz at 12dB/Octave Butterworth (Variable) Remote Controls Yes (RLC Remote Level Control included) Auto-Sense Turn-On Yes (with RAP bypass switch) Power Wire Gauge 4 AWG Power Input Connector Compression Terminal Block Speaker Wire Gauge 8 AWG Speaker Output Connector Compression Terminal Block Cooling Convection Heatsink Cast Aluminium Operating Voltage 9 - 16 VDC Recommended Fuse (not included) 80A Max Current Draw at 13.8V Sinewave 52A Visual Indicators Power: Blue / Protect: Red / C.L.E.A.N. In: Red / C.L.E.A.N. Out: Blue/Red Dimensions (H x W x D) 49 x 173 x 215mm (1.9 x 6.8 x 8.5 inch) CTA-2006 Compliant Yes Warranty 1 Year Compatible With / Goes Well With The R2-500X1 suits car audio builds requiring a dedicated mono subwoofer amplifier at the Prime R2 price point. Its RCA pass-through outputs pair naturally with the R2-500X4 4-channel speaker amplifier for a complete R2 series system. Goes Well With: R2-2X12 / R2-2X10 - Rockford Fosgate Prime dual loaded subwoofer enclosures, a matched Prime series pairing for the R2-500X1 at 2-ohm R2D2-12 / R2D2-10 - Prime R2 series individual subwoofers for custom enclosure builds R2-500X4 - Companion R2 series 4-channel speaker amplifier, chainable via the R2-500X1's RCA pass-through outputs R2-750X5 - Alternative single-unit R2 5-channel amplifier if a combined speaker and subwoofer solution is preferred RFK4 - Rockford Fosgate 4 AWG amplifier wiring kit to complete the installation Frequently Asked Questions What is the difference between the R2-500X1 and the R2-750X1? Both are Prime R2 series mono Class-D subwoofer amplifiers with Punch EQ, variable infrasonic filter, RLC remote, and RCA pass-through. The key differences are maximum rated output and impedance stability. The R2-500X1 delivers 500W RMS at 2-ohm and 300W at 4-ohm, with no 1-ohm rating. The R2-750X1 delivers 750W RMS at 1-ohm, 500W at 2-ohm, and 250W at 4-ohm, adding 1-ohm stability for builds using a dual voice coil subwoofer wired to 1-ohm. The R2-500X1 also uses a smaller 80A fuse versus 120A on the R2-750X1. Choose the R2-500X1 for 2-ohm or 4-ohm subwoofer builds; choose the R2-750X1 for maximum output or 1-ohm stability. What impedance gives the most power from the R2-500X1? The R2-500X1 delivers maximum rated output at 2-ohm (500W RMS, 590W dynamic). At 4-ohm the rated output is 300W RMS. The R2-500X1 is not 1-ohm rated. For maximum output, pairing with a subwoofer or dual subwoofer configuration wired to a 2-ohm total load is recommended. Can the R2-500X1 be used with a factory OEM head unit? Yes. High-level inputs accept OEM head unit speaker outputs at 450mV-12V. Auto-Sense turn-on activates the amplifier automatically when a signal is detected on the high-level input, removing the need for a dedicated remote wire. A RAP bypass switch is also included. What fuse does the R2-500X1 require and is it included? The R2-500X1 requires an 80A fuse, which is not included and must be sourced separately. The maximum sinewave current draw is 52A. Install the fuse as close to the battery as possible in the 4 AWG power supply line. Can I add a speaker amplifier to a system using the R2-500X1? Yes. The R2-500X1 includes RCA pass-through outputs that are active with both RCA and high-level input, allowing a clean signal to be passed to a downstream 4-channel speaker amplifier such as the R2-500X4. This is the recommended configuration for a complete R2 series car audio system.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less