Light Up the Trail ENLIGHT10 4ft Dynamic RGB Whip with 360° LEDs, IP65 Rated and Quick-Release Product Overview The Stinger SPXDW4 is a 4-foot dynamic RGB whip light from the ENLIGHT10 SPXD range, designed for off-road vehicles, ATVs, UTVs, and powersports applications. Built around 360° of dynamic RGB LEDs with fully customisable colour patterns, the SPXDW4 delivers a highly visible, personalised light show in the most demanding environments. The silicone-coated whip carries an IP65 rating, providing heavy-duty protection against water, mud, sand, dust, and debris. A quick-release mounting system allows the whip to be detached in seconds when not needed. Rugged watertight connectors are used throughout. The SPXDW4 is HEIGH10-compatible and can be controlled via the Stinger enLIGHT10 app on a smartphone. Key Specifications Manufacturer Part Number: SPXDW4 Whip length: 4ft (approximately 1.2m) LED configuration: 360° dynamic RGB Weather rating: IP65 Coating: Silicone Quick-release: Yes Connectors: Watertight ENLIGHT10 RGB module required: Yes — not included (SPXDBTC sold separately, or included with SPXDK4 / SPXDK8) HEIGH10 compatible: Yes App compatible: Yes — Stinger enLIGHT10 app (Bluetooth controller required) Included: 4ft dynamic RGB whip, extension harness, installation hardware Features & Benefits 360° Dynamic RGB LEDs — Full 360-degree illumination with variable dynamic colours, lighting patterns, and brightness levels — fully customisable via the enLIGHT10 app or HEIGH10 infotainment. IP65 Silicone Coating — The heavy-duty silicone outer coating is rated IP65, providing waterproof, shockproof, and dust-proof protection against the full range of off-road conditions — water, mud, sand, dirt, and debris. Quick-Release System — Detaches from the mounting point in seconds, making it simple to remove the whip for transport, storage, or when not in use without tools. HEIGH10 Compatible — Integrates directly with the Stinger HEIGH10 infotainment system (with SE-SXMHAR harness, sold separately) for in-dash lighting control alongside your audio and navigation. Stinger enLIGHT10 App Control — Full colour, pattern, and brightness control via the enLIGHT10 smartphone app when paired with the SPXDBTC Bluetooth controller (sold separately). Rugged Watertight Connectors — All connections use watertight connectors, maintaining the IP65-level protection through the full harness run. Extension Harness & Hardware Included — An extension harness and all necessary installation hardware are supplied in the box, reducing additional parts needed to complete the installation. Technical Specs Specification Detail Part Number SPXDW4 Brand Stinger Whip Length 4ft (~1.2m) LED Type Dynamic RGB LED Coverage 360° Weather Rating IP65 Coating Silicone Quick-Release Yes Connectors Watertight ENLIGHT10 RGB Module Required — not included HEIGH10 Compatible Yes App Control Yes — Stinger enLIGHT10 app (SPXDBTC required) Included 4ft RGB whip, extension harness, installation hardware Compatible With / Goes Well With Stinger ENLIGHT10 SPXDBTC Bluetooth controller (required RGB module — sold separately) Stinger ENLIGHT10 SPXDK4 rock light kit (includes RGB module) Stinger ENLIGHT10 SPXDK8 rock light kit (includes RGB module) Stinger HEIGH10 infotainment system (via SE-SXMHAR harness, sold separately) Stinger enLIGHT10 smartphone app Stinger SPXYADP Y adapter harness (sold separately) Off-road vehicles, ATVs, UTVs, Jeeps, trucks, and powersports vehicles Frequently Asked Questions Does the SPXDW4 include the RGB controller module? No — an ENLIGHT10 RGB module is required and is not included. The SPXDBTC Bluetooth controller is available separately, or is included with the SPXDK4 and SPXDK8 rock light kits if you are building a combined system. What is the IP rating of the SPXDW4? The SPXDW4 carries an IP65 rating, providing protection against water jets, heavy dust, mud, sand, and debris — built for genuine off-road and powersports environments. How does the quick-release system work? The SPXDW4 features a quick-release mounting system that allows the whip to be detached from its mount in seconds without tools — useful for removing it during transport, storage, or when it's not required for a particular trip. Can the SPXDW4 be controlled from a Stinger HEIGH10 head unit? Yes — the SPXDW4 is HEIGH10 compatible. Connection requires the SE-SXMHAR ENLIGHT10 replacement harness (sold separately) along with the HEIGH10 running the latest firmware. What is included in the box? The box includes the 4ft dynamic RGB whip, an extension harness, and installation hardware. The ENLIGHT10 RGB module (SPXDBTC) is not included and must be sourced separately. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Split Your ENLIGHT10 Harness Run Single 3-Pin Y Adapter, Plug-In Ready Product Overview The Stinger SPXYADP is a single 3-pin Y adapter harness for use with compatible Stinger ENLIGHT10 lighting products. It allows additional harness connections to be added to a lighting run, enabling more flexible layouts and extended coverage across an ENLIGHT10 installation. Unlike the SPXDMF solder-on connector pack, the SPXYADP is a pre-assembled harness a single unit providing an immediate plug-in Y connection point with no soldering required. Compatible ENLIGHT10 products are the SPXDK4, SPXDK8, SPXDE4, SPXDUBKIT, SPXD5, and SPXDBTC broader compatibility than the SPXDMF, covering more of the ENLIGHT10 SPXD range. Key Specifications Manufacturer Part Number: SPXYADP Function: 3-pin Y adapter harness for ENLIGHT10 harness expansion Compatible products: Stinger ENLIGHT10 SPXDK4, SPXDK8, SPXDE4, SPXDUBKIT, SPXD5, SPXDBTC Connector type: 3-pin Y harness (pre-assembled) Quantity: 1x harness Soldering required: No Application: ENLIGHT10 harness addition and layout customisation Features & Benefits Pre-Assembled Y Harness — Unlike solder-on connector packs, the SPXYADP is a ready-to-use pre-assembled harness — just plug in and extend your ENLIGHT10 lighting run without tools or soldering. Broad ENLIGHT10 Compatibility — Compatible with SPXDK4, SPXDK8, SPXDE4, SPXDUBKIT, SPXD5, and SPXDBTC — covering the majority of ENLIGHT10 SPXD products in a single accessory. Flexible Layout Expansion — Enables additional lighting products or harness branches to be added to an existing ENLIGHT10 installation, giving more options when a single run doesn't reach all mounting locations. Technical Specs Specification Detail Part Number SPXYADP Brand Stinger Function 3-pin Y adapter harness Connector Type 3-pin Y (pre-assembled) Quantity 1x harness Soldering Required No Compatible Products SPXDK4, SPXDK8, SPXDE4, SPXDUBKIT, SPXD5, SPXDBTC Application ENLIGHT10 harness addition and customisation Compatible With / Goes Well With Stinger ENLIGHT10 SPXDK4 Stinger ENLIGHT10 SPXDK8 Stinger ENLIGHT10 SPXDE4 Stinger ENLIGHT10 SPXDUBKIT Stinger ENLIGHT10 SPXD5 Stinger ENLIGHT10 SPXDBTC Caution: The SPXYADP is for use with Stinger ENLIGHT10 products only. Compatibility with other lighting systems or third-party accessories is not confirmed by the supplier. Frequently Asked Questions What is the SPXYADP used for? The SPXYADP is a pre-assembled 3-pin Y adapter harness that allows additional harness connections to be added to a compatible ENLIGHT10 lighting installation, enabling more flexible layout coverage without soldering. Does the SPXYADP require soldering? No — the SPXYADP is a pre-assembled harness and is plug-in ready. No soldering tools or additional hardware are required for installation. How many harnesses are included? The SPXYADP includes one 3-pin Y harness. If multiple Y connection points are needed, additional SPXYADP units will be required. Which ENLIGHT10 products is the SPXYADP compatible with? The SPXYADP is confirmed for use with Stinger ENLIGHT10 products SPXDK4, SPXDK8, SPXDE4, SPXDUBKIT, SPXD5, and SPXDBTC. What is the difference between the SPXYADP and the SPXDMF? The SPXYADP is a single pre-assembled plug-in Y harness — no soldering required. The SPXDMF is a pack of solder-on male and female connectors with heat shrink for those building custom harness sections. The SPXYADP suits a quick plug-in expansion; the SPXDMF suits a custom hardwired installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Expand Your ENLIGHT10 Lighting Run 3-Pin Y Harness Pack for SPXD5 and SPXDUBKIT Product Overview The Stinger SPXDMF is an 8-pack of 3-pin Y harness connectors designed for expanding or extending lighting harness runs on compatible Stinger ENLIGHT10 products. The pack contains four male and four female solder-on connectors, along with 16 pieces of heat shrink, providing the hardware needed to add additional harness sections to SPXD5 LED strip and SPXDUBKIT installations. This is a wiring accessory intended for use by those customising or extending their ENLIGHT10 lighting layout. It is for use with Stinger ENLIGHT10 SPXD5 and SPXDUBKIT only. Key Specifications Manufacturer Part Number: SPXDMF Function: 3-pin Y harness connectors for ENLIGHT10 harness expansion Compatible products: Stinger ENLIGHT10 SPXD5, SPXDUBKIT Contents: 4x female solder-on connectors, 4x male solder-on connectors, 16x heat shrink pieces Total connectors: 8 (4 male + 4 female) Connector type: 3-pin solder-on Application: ENLIGHT10 harness addition and customisation Features & Benefits Harness Expansion Made Simple — Provides the solder-on connectors and heat shrink needed to add additional ENLIGHT10 harness sections to an SPXD5 or SPXDUBKIT installation, without sourcing individual components. Matched Male and Female Pairs — The pack includes both male and female connectors in equal quantities (4 of each), covering the connection points needed for Y-harness splits and extensions. Heat Shrink Included — 16 pieces of heat shrink are supplied alongside the connectors, providing the insulation needed for clean, weatherproof solder joints without a separate hardware run. Customise Your Install — Enables a more flexible lighting layout by allowing additional harness branches to be added where the standard harness length or configuration doesn't reach. Technical Specs Specification Detail Part Number SPXDMF Brand Stinger Function 3-pin Y harness connectors for ENLIGHT10 Connector Type Solder-on, 3-pin Female Connectors 4x Male Connectors 4x Heat Shrink Pieces 16x Total Pack Contents 8 connectors + 16 heat shrink pieces Compatible Products Stinger ENLIGHT10 SPXD5, SPXDUBKIT Application Harness addition and customisation Compatible With / Goes Well With Stinger ENLIGHT10 SPXD5 LED strips Stinger ENLIGHT10 SPXDUBKIT Frequently Asked Questions What is the SPXDMF used for? The SPXDMF provides 3-pin solder-on Y harness connectors and heat shrink for adding additional harness sections to Stinger ENLIGHT10 SPXD5 and SPXDUBKIT installations, allowing a more customised or extended lighting layout. What is included in the pack? The pack contains 4x female solder-on connectors, 4x male solder-on connectors, and 16x heat shrink pieces — a total of 8 connectors with heat shrink for insulation. Do I need to solder to use the SPXDMF? Yes — the SPXDMF uses solder-on connectors. Soldering is required to attach the connectors to the harness. The included heat shrink provides insulation over the solder joints for a clean, weatherproof finish. Which ENLIGHT10 products is the SPXDMF compatible with? The SPXDMF is confirmed for use with Stinger ENLIGHT10 SPXD5 LED strips and the SPXDUBKIT only. It is not confirmed for use with other ENLIGHT10 products. Is the SPXDMF a plug-and-play accessory? No — the SPXDMF requires soldering. It is a wiring accessory for those customising or extending their ENLIGHT10 harness layout, not a plug-in solution. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Control Your ENLIGHT10 Lighting From Your HEIGH10 The Harness That Makes It Happen Product Overview The Stinger SE-SXMHAR is a replacement harness that connects compatible Stinger ENLIGHT10 SPXD lighting products to the Stinger HEIGH10 infotainment system, enabling direct lighting control from the HEIGH10's interface. Once connected, the HEIGH10 can change colours, toggle lights on and off, link lighting colour to match the HEIGH10's own illumination colour, and set lights to activate automatically with the vehicle's headlights via the AUTO function. Compatible ENLIGHT10 products are the SPXDBTC, SPXDK8, SPXDK4, and SPXDUBKIT. The HEIGH10 infotainment system must be running the latest firmware version for ENLIGHT10 integration to function. The harness can also be used alongside the enLIGHT10 by Stinger smartphone app for additional control options. Key Specifications Manufacturer Part Number: SE-SXMHAR Function: ENLIGHT10 to HEIGH10 connection harness Compatible head unit: Stinger HEIGH10 (latest firmware required) Compatible ENLIGHT10 products: SPXDBTC, SPXDK8, SPXDK4, SPXDUBKIT HEIGH10 firmware: Latest version required — update before installation Control functions: Colour change, on/off, link to HEIGH10 illumination colour, AUTO headlight trigger App compatible: Yes — enLIGHT10 by Stinger smartphone app Included: Harness only Features & Benefits HEIGH10 Lighting Integration — Connects ENLIGHT10 SPXD lighting directly to the HEIGH10 infotainment system, enabling full lighting control from the head unit's touchscreen interface without reaching for a separate remote or phone. Colour Matching — LINK Mode — The LINK function synchronises SPXD lighting colour to match the HEIGH10's own illumination colour, creating a coordinated interior and exterior lighting look. AUTO Headlight Trigger — Set to AUTO and the SPXD lights will turn on and off in sync with the vehicle's headlights, eliminating the need to manually control lighting every time the lights are switched. Dual Control — HEIGH10 or App — Lighting can be controlled from the HEIGH10 screen or the enLIGHT10 by Stinger smartphone app, giving flexible access from wherever is most convenient. Replacement Harness — Provides a direct replacement for a missing or damaged connection harness between the HEIGH10 and ENLIGHT10 products, restoring integration without needing new hardware. Technical Specs Specification Detail Part Number SE-SXMHAR Brand Stinger Function ENLIGHT10 to HEIGH10 connection harness Compatible Head Unit Stinger HEIGH10 (latest firmware required) Compatible ENLIGHT10 Products SPXDBTC, SPXDK8, SPXDK4, SPXDUBKIT HEIGH10 Firmware Latest version required Control Modes Colour change, on/off, LINK, AUTO App Control Yes — enLIGHT10 by Stinger app Included Harness only Compatible With / Goes Well With Stinger HEIGH10 infotainment system (latest firmware version) Stinger ENLIGHT10 SPXDBTC Bluetooth controller Stinger ENLIGHT10 SPXDK8 Stinger ENLIGHT10 SPXDK4 Stinger ENLIGHT10 SPXDUBKIT enLIGHT10 by Stinger smartphone app Caution: The HEIGH10 must be running the latest firmware version for ENLIGHT10 integration to function — update firmware before installation. The SE-SXMHAR is for use with Stinger HEIGH10 and ENLIGHT10 products only. Compatibility with other head units or third-party lighting systems is not confirmed. Frequently Asked Questions What does the SE-SXMHAR do? The SE-SXMHAR is a connection harness that links compatible Stinger ENLIGHT10 SPXD lighting products to the Stinger HEIGH10 infotainment system, enabling lighting control — including colour, on/off, LINK mode, and AUTO headlight trigger — directly from the HEIGH10 interface. Does the HEIGH10 need to be updated before using this harness? Yes — the HEIGH10 must be running the latest firmware version for ENLIGHT10 integration to function. Update the HEIGH10 firmware via the Stinger update process before connecting the SE-SXMHAR. Which ENLIGHT10 products work with the SE-SXMHAR? The SE-SXMHAR is confirmed compatible with Stinger ENLIGHT10 products SPXDBTC, SPXDK8, SPXDK4, and SPXDUBKIT. Can I still use the smartphone app after installing the SE-SXMHAR? Yes — the enLIGHT10 by Stinger app remains available as an alternative control method alongside the HEIGH10 interface, giving flexible control from either the head unit or a smartphone. What is included in the box? The box contains the connection harness only. The Stinger HEIGH10 infotainment system and ENLIGHT10 products are sold separately. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Take Full Control of Your ENLIGHT10 RGB Lighting App or RF Remote, All Weather, All Adventure Product Overview The Stinger SPXDBTC is a dynamic Bluetooth controller designed for use with Stinger ENLIGHT10 SPXD-series LED products. It allows simultaneous control of colours and lighting patterns across connected SPXD LED lights via the Stinger Lighting smartphone app or the included RF remote control giving full flexibility whether you're on the trail, on the water, or parked up. The controller is weatherproof with watertight connectors, making it suited to the environments where ENLIGHT10 lighting products are typically installed Jeeps, trucks, motorcycles, ATVs, UTVs, boats, and other off-road and powersports vehicles. Compatible SPXD products are the SPXDE4, SPXD5, and SPXDW4. The SPXDBTC is for use with the Stinger Lighting app and Stinger ENLIGHT10 products only. Key Specifications Manufacturer Part Number: SPXDBTC Function: Bluetooth + RF remote RGB lighting controller Control methods: Stinger Lighting smartphone app + included RF remote Compatible products: Stinger ENLIGHT10 SPXDE4, SPXD5, SPXDW4 Weatherproof: Yes — weatherproof controller body Connectors: Watertight App: Stinger Lighting app (required for app control) System: ENLIGHT10 products only Included: RF remote control, weatherproof Bluetooth controller, watertight connectors Features & Benefits Dual Control — App or RF Remote — Control colours and lighting patterns via the Stinger Lighting smartphone app for full feature access, or use the included RF remote for quick, no-phone adjustments on the go. Simultaneous Multi-Light Control — The SPXDBTC controls multiple connected SPXD LED products simultaneously, allowing coordinated colour and pattern changes across rocks, whips, and strips in a single operation. Weatherproof Controller & Watertight Connectors — The controller body is weatherproof and uses watertight connectors, making it suitable for exposed mounting positions in off-road, marine, and powersports applications. Broad Vehicle Application — Designed for use on Jeeps, trucks, motorcycles, ATVs, UTVs, boats, and other adventure and powersports vehicles where SPXD lighting is installed. SPXD LED Ecosystem — Pairs with SPXDE4 rock lights, SPXD5 LED strips, and SPXDW4 whip lights within the ENLIGHT10 SPXD product range, enabling a combined multi-product lighting setup from a single controller. Technical Specs Specification Detail Part Number SPXDBTC Brand Stinger Function Bluetooth RGB lighting controller with RF remote Control Methods Stinger Lighting app + RF remote Compatible Products SPXDE4, SPXD5, SPXDW4 System Stinger ENLIGHT10 only Controller Weatherproofing Yes — weatherproof Connectors Watertight App Required Stinger Lighting app (for app control) Included RF remote, weatherproof controller, watertight connectors Compatible With / Goes Well With Stinger ENLIGHT10 SPXDE4 rock lights Stinger ENLIGHT10 SPXD5 LED strips Stinger ENLIGHT10 SPXDW4 whip lights Stinger Lighting smartphone app (iOS and Android — confirm current platform support) Stinger SPXCLA cigarette lighter adaptor harness (sold separately) Caution: The SPXDBTC is for use with the Stinger Lighting app and Stinger ENLIGHT10 products only. It is not compatible with non-ENLIGHT10 LED systems or third-party RGB controllers. Confirm smartphone app availability for your device platform before purchase. Frequently Asked Questions What ENLIGHT10 products is the SPXDBTC compatible with? The SPXDBTC is confirmed compatible with Stinger ENLIGHT10 SPXDE4 rock lights, SPXD5 LED strips, and SPXDW4 whip lights. It is for use with Stinger ENLIGHT10 products and the Stinger Lighting app only. Can I control the SPXDBTC without a smartphone? Yes — the included RF remote control allows colour and pattern control without using the smartphone app, giving convenient wireless control in situations where phone access isn't practical. Is the controller suitable for outdoor and off-road use? Yes — the SPXDBTC features a weatherproof controller body and watertight connectors, making it suitable for exposed mounting positions in off-road, marine, motorcycle, ATV, UTV, and boat applications. What app is required to control the SPXDBTC? The Stinger Lighting app is required for smartphone-based control. Confirm current app availability for your device platform (iOS/Android) before purchase. What is included in the box? The kit includes the weatherproof Bluetooth controller, an RF remote control, and watertight connectors. Compatible ENLIGHT10 LED products are sold separately. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Power Your ENLIGHT10 From the Cig Socket Simple Adaptor With On/Off Switch Included Product Overview The Stinger SPXCLA is a cigarette lighter adaptor harness designed specifically for use with Stinger ENLIGHT10 products. It provides a clean, simple power connection from a standard 12V cigarette lighter socket to the ENLIGHT10 accessory via bullet terminals, with an on/off switch built in for convenient control without reaching for the unit itself. Compatible ENLIGHT10 products are the SPXDK8, SPXDK4, SPXDUBKIT, and SPXDBTC. It is not a universal cigarette lighter adaptor use with non-ENLIGHT10 products is not confirmed by the supplier. Key Specifications Manufacturer Part Number: SPXCLA Function: Cigarette lighter adaptor to bullet terminals On/off switch: Yes — included Compatible products: Stinger ENLIGHT10 SPXDK8, SPXDK4, SPXDUBKIT, SPXDBTC Universal fit: No — ENLIGHT10 products only Included: Cig lighter adaptor to bullet terminals harness Features & Benefits Cigarette Lighter Power Connection — Draws power directly from a standard 12V cigarette lighter socket, allowing ENLIGHT10 products to be powered without hardwiring into the vehicle's electrical system. On/Off Switch Included — The built-in on/off switch provides simple power control without needing to unplug the adaptor or access the ENLIGHT10 unit itself. Bullet Terminal Output — Terminates in bullet connectors compatible with the ENLIGHT10 product range for a clean, secure connection. Plug and Go — A straightforward accessory that simplifies ENLIGHT10 installation, particularly for temporary or semi-permanent setups. Technical Specs Specification Detail Part Number SPXCLA Brand Stinger Function Cig lighter adaptor to bullet terminals On/Off Switch Yes — included Compatible Products SPXDK8, SPXDK4, SPXDUBKIT, SPXDBTC Application Stinger ENLIGHT10 products only Included Cig lighter adaptor harness with bullet terminals Compatible With / Goes Well With Stinger ENLIGHT10 SPXDK8 Stinger ENLIGHT10 SPXDK4 Stinger ENLIGHT10 SPXDUBKIT Stinger ENLIGHT10 SPXDBTC Frequently Asked Questions What Stinger products is the SPXCLA compatible with? The SPXCLA is confirmed for use with Stinger ENLIGHT10 products SPXDK8, SPXDK4, SPXDUBKIT, and SPXDBTC only. It is not confirmed for use with other Stinger or third-party products. Does the SPXCLA include an on/off switch? Yes — an on/off switch is built into the harness, allowing the connected ENLIGHT10 product to be switched on or off without unplugging the adaptor from the cigarette lighter socket. What connector type does the SPXCLA use at the output end? The SPXCLA terminates in bullet terminals, matching the input connection on compatible ENLIGHT10 products. Can the SPXCLA be used as a general-purpose cigarette lighter adaptor? No — the SPXCLA is designed specifically for Stinger ENLIGHT10 products. It is not a universal cigarette lighter adaptor and should not be assumed compatible with other devices or accessories. What is included in the box? The box contains the cigarette lighter adaptor to bullet terminals harness with integrated on/off switch. No additional accessories are included. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger SFDGM07 Double DIN Fascia Holden Colorado Manual Climate A vehicle-specific Double DIN fascia panel for the Holden Colorado RG (2016-2019) with manual climate controls, the SFDGM07 allows the installation of an aftermarket Double DIN head unit into the Colorado dashboard. Product Overview The Stinger SFDGM07 is a Double DIN fascia panel designed specifically for the Holden Colorado RG from 2016-2019 fitted with manual climate controls. It is designed to accommodate an aftermarket Double DIN head unit in the Holden Colorado dashboard. This fascia is suited to manual climate control models only; Colorado models with automatic climate controls require a different fascia. Confirm your specific Colorado variant and climate control type before purchase. Features & Benefits Holden Colorado RG 2016-2019 Specific Fitment: The SFDGM07 is designed specifically for the Holden Colorado RG from 2016-2019, providing a precise dashboard fit for Double DIN aftermarket head unit installations in this generation of Colorado. Double DIN Aperture: The SFDGM07 provides the correct Double DIN aperture for the installation of standard Double DIN aftermarket head units into the Holden Colorado dashboard. Manual Climate Control Models Only: The SFDGM07 suits Holden Colorado RG models fitted with manual climate controls. Models with automatic climate controls require a different fascia panel. Confirm the climate control type of your specific vehicle before purchase. Colorado 7 Compatible: The SFDGM07 is also compatible with the Holden Colorado 7 within the supported date range and chassis code. Technical Specs Specification Detail SKU SFDGM07 Brand Stinger Compatible Vehicles Holden Colorado RG 2016-2019, Holden Colorado 7 RG 2016-2019 Climate Control Compatibility Manual Climate Controls Only Application Double DIN Compatible With The SFDGM07 is designed for the Holden Colorado and Colorado 7 RG from 2016-2019 fitted with manual climate controls. It is not suitable for Holden Colorado models with automatic climate controls. Confirm your specific Colorado variant, build date, and climate control type before purchase. Frequently Asked Questions Is the SFDGM07 compatible with automatic climate control Colorado models? No. The SFDGM07 is designed for Holden Colorado RG models with manual climate controls only. Models fitted with automatic climate controls require a different fascia panel. Is the SFDGM07 compatible with Single DIN head units? No. The SFDGM07 provides a Double DIN aperture and is designed for standard Double DIN aftermarket head units only. Does the SFDGM07 include wiring harnesses or steering wheel control adaptors? The SFDGM07 is a fascia panel only. Wiring harnesses, steering wheel control interfaces, and antenna adaptors need to be sourced separately for a complete installation. Is the SFDGM07 compatible with the Holden Colorado 7? Yes. The SFDGM07 is compatible with the Holden Colorado 7 RG within the 2016-2019 date range with manual climate controls. Does the SFDGM07 include mounting hardware? Mounting hardware details are not specified in the source data for this product. Confirm hardware inclusions with your supplier before purchase.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

X3 Series Flagship 2-Channel RCA Interconnect 17ft, Silver-Plated Pure OFC, Lock Tip Quad-Clamp Locking Connectors, Dual-Layer I.D. Shielding, C3 Tech, Body Armor Protection. Product Overview The Stinger XI3217 is the flagship X3 Series 17-foot (approximately 5.2-metre) 2-channel RCA interconnect positioned above the 8000 Series SI8217 in the Stinger range and engineered for high-performance installations where the signal cable must match the capability of the amplifier it serves. At 17 feet, it covers the full head-unit-to-boot-amplifier run in most vehicles with cable to spare for routing around obstacles. The X3 design addresses every major source of signal degradation in a car audio RCA connection. Silver-plated pure OFC conductors optimise performance across the full audio frequency range. Lock Tip Quad-Clamp locking RCA connectors with a precision 4-cut contact physically lock onto the socket, eliminating the intermittent contact caused by vibration-loosened push-fit connectors. I.D. (Interference Defense) dual-layer shielding combines an inner Mylar foil layer for external EMI rejection with an outer copper mesh layer for conducted noise rejection two separate shielding mechanisms targeting two different noise sources. Directional double twisted-pair construction with three conductors per channel (positive, negative, signal drain) completes the signal path architecture. C3 Tech ensures no breaks or discontinuities throughout the full 17-foot length. Body Armor nylon-woven outer protection covers the flexible PVC inner cable for mechanical durability in installation and beyond. Key Specifications SKU: XI3217 Series: X3 Channels: 2 Length: 17 feet (approximately 5.2 metres) Conductor: Silver-plated pure OFC copper, finely stranded Conductor construction: Double twisted-pair, directional Noise cancellation: Directional twisted-pair architecture Shielding: Dual-layer — inner Mylar EMI foil + outer copper mesh Connector type: Lock Tip Locking RCA — Quad-Clamp 4-cut Construction method: C3 Tech (Continuous Connection Construction) Outer protection: Body Armor — nylon-woven over PVC Conductors per channel: 3 (positive, negative, signal drain) Warranty: Not specified — confirm with Stinger Features & Benefits Lock Tip Quad-Clamp 4-Cut Locking RCA Connectors The Lock Tip connector combines a rotational locking end with a precision 4-cut Quad-Clamp contact — physically clamping and locking onto the RCA socket with the highest possible contact force. Standard push-fit connectors rely on friction only and loosen under vibration, introducing intermittent noise and signal dropout. The Lock Tip design eliminates this failure mode entirely — the most common source of noise in car audio signal chains. Silver-Plated Pure OFC Conductors Pure OFC (Oxygen-Free Copper) eliminates the oxidation-related signal degradation of standard copper conductors. Silver plating each individual strand further reduces surface resistance — where the majority of high-frequency audio signal travels due to the skin effect — optimising performance across the full 20Hz–20kHz audio spectrum. The combination delivers tight bass response and crystal-clear high-frequency detail over the full 17-foot run. I.D. Dual-Layer Interference Defense Shielding Two independent shielding layers target two different noise sources simultaneously. The inner Mylar foil layer rejects radiated electromagnetic interference from external sources — alternators, ignition systems, and mobile devices. The outer copper mesh layer absorbs conducted radiated noise generated within the cable's own conductors. A single-layer shield addresses only one source; the XI3217's dual-layer design addresses both. Directional Double Twisted-Pair Construction — Three Conductors per Channel Three conductor bundles per channel — positive, negative, and signal drain — are arranged in a directional double twisted-pair architecture that uses the physics of twisted-pair noise cancellation to reject interference. The directional design means the cable is installed in a specific orientation for maximum noise rejection. Separate signal drain conductor isolates the shield drain from the audio return path. C3 Tech — Continuous Connection Construction Stinger's C3 Tech ensures no micro-discontinuities, solder joints, or resistance variations throughout the full 17-foot length — providing consistent signal transfer from source unit to amplifier. Body Armor Nylon-Woven Outer Protection High-strength nylon fibres woven over a flexible PVC inner cable provide mechanical protection against the sharp metal edges, vibration fatigue, and moisture ingress encountered during vehicle installation — and throughout the life of the cable in an automotive environment. Technical Specs Specification Detail Brand Stinger SKU XI3217 Series X3 Channels 2 Length 17 feet (approx. 5.2 metres) Conductor Silver-Plated Pure OFC Copper, Finely Stranded Conductor Construction Double Twisted-Pair, Directional Conductors per Channel 3 (positive, negative, signal drain) Shielding Dual-Layer: Mylar EMI Foil + Copper Mesh Connector Type Lock Tip Locking RCA — Quad-Clamp 4-Cut Construction Method C3 Tech Noise Cancellation Directional Twisted-Pair Architecture Outer Protection Body Armor — Nylon-Woven over PVC Warranty Not confirmed — confirm with Stinger Compatible With / Goes Well With Suitable for: High-performance amplifier installations where signal cable quality must match a premium amplifier's noise floor and dynamic range Full-length vehicle runs from dash-mounted head unit to boot-mounted amplifier in most passenger cars, SUVs, and medium-sized vans Installations where Lock Tip locking connectors are preferred over standard push-fit for vibration-resistant signal integrity Pairs well with: Rockford Fosgate, Hertz, Morel, and AudioControl premium amplifiers Stinger SI8212 (12ft / 3.7m) 8000 Series for shorter runs where the same installation quality is required at a reduced length Stinger SI82YF and SI82YM Y-adapters if a consistent Stinger build across all RCA connections is required Frequently Asked Questions What is the benefit of silver-plated conductors over standard OFC copper? Standard OFC copper provides low resistance and solid signal transfer. Silver plating each individual OFC strand reduces surface resistance further — where the majority of high-frequency audio signal travels due to the skin effect. This optimises performance across the full 20Hz–20kHz range, particularly at higher frequencies where signal integrity matters most. How do the Lock Tip locking RCA connectors differ from standard RCA connectors? A standard push-fit RCA connector relies on friction to maintain contact — which loosens under vibration and causes intermittent noise or signal dropout. The Lock Tip connector adds a rotational locking mechanism and a Quad-Clamp 4-cut contact that physically clamps onto the RCA socket, maintaining consistent contact force regardless of vibration, temperature cycling, or mechanical stress. What does dual-layer shielding provide that a single shield does not? A single shielding layer typically targets either radiated external interference or conducted internal noise. The XI3217's inner Mylar foil layer specifically rejects external EMI from alternators and ignition systems, while the outer copper mesh layer absorbs conducted noise generated within the cable's own conductors — each layer targeting a different noise source for substantially better total rejection than either alone. What does the directional construction mean, and how do I install it correctly? The directional twisted-pair architecture cancels noise most effectively when signal flows from source unit to amplifier. Directional markings on the cable indicate the correct orientation. Installing in reverse does not damage the cable but reduces the effectiveness of the noise-cancelling architecture. Is 17 feet sufficient for most vehicle installations? At 17 feet (approximately 5.2m), the XI3217 covers the full head-unit-to-boot-amplifier run in most passenger cars, SUVs, and medium-sized vans with cable to spare. For very large vehicles or installations where the routing path adds significantly to the direct distance, measure the intended routing path before purchase. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

The Cleanest Digital Signal Path in Car Audio 17ft Toslink Optical Interconnect Built for DSP and High-Performance Installs Product Overview The Stinger XI1117 is a 17-foot (5-metre) Toslink optical interconnect from the X Series range, engineered to provide the cleanest possible digital audio connection between source units, DSP processors, PAC AmpPRO vehicle interfaces, and Stinger Infotainment systems. Unlike RCA cables that carry audio as an analogue electrical signal, the XI1117 transmits audio as light making it completely immune to electromagnetic interference, alternator whine, ground loops, and every other form of electrical noise that degrades signal quality in the automotive environment. The cable uses a medical-grade light-conductive fibre optic core, triple-polished at both ends to maximise light transfer efficiency and minimise the optical data errors that cause digital jitter and sonic degradation. Stinger's proprietary C3 Tech (Continuous Connection Construction) method ensures no breaks in the optical signal chain across the full 17-foot length. A Quad-Lock precision connector resists vibration for a secure, consistently aligned connection. The flexible non-reflective PVC dielectric jacket allows routing through tight dash and cabin spaces without risk to the fibre core. Hi-Res Audio ready, with support for 5.1 and 7.1 DTS and Dolby Digital. At 17 feet, the XI1117 covers the full run from a dash-mounted source or head unit to a boot-mounted DSP processor in most vehicles without the need for extension. Key Specifications Manufacturer Part Number / SKU: XI1117 Series: X Series Cable type: Toslink optical Length: 17ft (5 metres) Core material: Medical-grade light-conductive fibre optic Connector finish: Triple-polished Connector type: Quad-Lock Stinger Toslink Construction method: C3 Tech (Continuous Connection Construction) Outer jacket: Durable automotive-grade Inner insulation: Flexible non-reflective PVC dielectric Multi-channel support: Yes — 5.1 and 7.1 DTS, Dolby Digital Hi-Res Audio ready: Yes Noise immunity: Total — optical transmission, no electrical connection Frequency response: Extended beyond RCA capability Features & Benefits Medical-Grade Fibre Optic Core — Manufactured to medical-grade standards for maximum optical clarity and signal transmission precision. This level of core quality directly reduces digital jitter and data errors, resulting in more detailed and accurate sound reproduction at the receiving DSP or processor. Triple-Polished Connector Ends — Both ends are triple-polished to create the smoothest possible light-emitting and receiving surfaces. Each polishing step removes microscopic surface imperfections that scatter light, maximising total light transfer and minimising data errors at the connection point. Total Noise Immunity — Audio transmitted as light rather than electrical current is immune to electromagnetic interference from alternators, ignition systems, mobile devices, and all other electrical noise sources in the vehicle. No shielding is required and no ground loops can form. Extended Frequency Response Beyond RCA — The optical digital signal path supports a frequency response far beyond the 20kHz ceiling of the analogue audio spectrum and beyond the practical capability of any RCA cable, making the XI1117 suitable for Hi-Res Audio sources and processors. Multi-Channel Audio Support — Supports 5.1 and 7.1 DTS and Dolby Digital multi-channel audio formats, providing full bandwidth for DSP processors and digital interfaces requiring multi-channel throughput over a single cable. C3 Tech — Continuous Connection Construction — Stinger's proprietary construction method ensures no breaks or discontinuities in the optical signal chain throughout the full 17-foot cable length, providing consistent signal transfer from source to destination. Quad-Lock Precision Connector — Resists vibration and mechanical stress in the automotive environment, maintaining a secure, correctly aligned connection at the optical interface — critical for consistent digital signal integrity. Flexible Non-Reflective PVC Dielectric Jacket — The non-reflective inner insulation prevents internal light scattering. The flexibility of the jacket allows routing through tight dash and cabin spaces without exceeding the minimum bend radius of the fibre core. Technical Specs Specification Detail SKU XI1117 Series X Series Cable Type Toslink Optical Length 17ft (5 metres) Core Material Medical-grade light-conductive fibre optic Connector Finish Triple-polished Connector Type Quad-Lock Stinger Toslink Construction Method C3 Tech (Continuous Connection Construction) Outer Jacket Durable automotive-grade Inner Insulation Flexible non-reflective PVC dielectric Multi-Channel Support Yes — 5.1 and 7.1 DTS, Dolby Digital Hi-Res Audio Ready Yes Noise Immunity Total — optical, no electrical connection Frequency Response Extended beyond RCA capability Compatible With / Goes Well With DSP processors with Toslink optical input (e.g. Rockford Fosgate DSR1, Morel MDSP series and equivalents) PAC AmpPRO vehicle interfaces with Toslink output Stinger HEIGH10 infotainment systems with TOSLINK output Any source unit or head unit with Toslink optical output Boot-mounted DSP and processor installations requiring a full-length dash-to-boot optical run Caution: Observe a minimum bend radius of at least 25–30mm at any point in the routing path. Do not bend sharply, kink, or route the cable through clips that compress it tightly — damage to the fibre core is permanent and will degrade optical performance. The flexible PVC jacket aids routing but does not protect the core from sharp bends. Frequently Asked Questions Why use a Toslink optical cable instead of an RCA cable for DSP connections? An RCA cable transmits audio as an analogue electrical signal susceptible to electromagnetic interference from alternators, ignition systems, and other noise sources in the vehicle. A Toslink optical cable transmits audio as light with no electrical connection between source and destination — completely immune to all electrical noise. In DSP installations, using an optical input already in the digital domain also eliminates an analogue conversion stage and the noise it introduces, resulting in a cleaner, more precise signal at the processor. What does triple polishing of the connector ends achieve? Each optical connector end must be as smooth as possible to maximise light transfer across the connection gap. Microscopic surface imperfections scatter light away from the receiving core, reducing signal strength and increasing data errors. Triple polishing removes successive layers of surface imperfection, creating a mirror-smooth optical surface that maximises light transfer and minimises the digital jitter caused by data errors. What is digital jitter and how does the XI1117 reduce it? Digital jitter is timing variation in the digital audio signal that causes samples to arrive at inconsistent intervals, manifesting as subtle but audible degradation of sonic resolution, imaging, and low-level detail. The XI1117 reduces jitter through its medical-grade fibre core, triple-polished connections, and C3 Tech construction — all of which maximise light transfer efficiency and minimise the optical data errors that contribute to jitter at the receiving device. Does the XI1117 support Hi-Res Audio and multi-channel formats? Yes — the XI1117's optical signal path supports a frequency response and bandwidth extending well beyond the 20kHz ceiling of standard CD-quality audio. It is Hi-Res Audio ready and supports 5.1 and 7.1 DTS and Dolby Digital multi-channel formats over a single cable connection. What minimum bend radius should I observe when routing the XI1117? Maintain a bend radius of at least 25–30mm at any point in the routing path. Avoid routing the cable around sharp corners or through clips that would compress or kink it — the fibre core can crack or fracture if bent below its minimum radius, permanently degrading optical performance. The flexible PVC jacket eases routing but does not protect against sharp bends. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

8000 Series 2-Channel Triple Shielded RCA 17ft, Oversized Silver-Plated Copper, Triple-Braided + Mylar Shielding, Locking Split-Tip Connectors, 3 Conductors per Channel, C3 Tech. Product Overview The Stinger SI8217 is a 17-foot (5-metre) 2-channel audiophile-grade RCA interconnect from the 8000 Series engineered for installations where signal quality is the priority and the routing distance demands a longer run. At 17 feet, the SI8217 covers the full head-unit-to-boot-amplifier run in most vehicles including SUVs, wagons, and vans, with cable to spare for routing around obstacles, through door sills, and along body creases. Oversized silver-plated copper conductors use three conductors per channel separate positive, negative, and signal drain paths ensuring true channel separation and a low-impedance signal return across the full 5-metre length. Triple-braided shielding combined with an inner Mylar foil layer provides multi-directional noise rejection critical over a longer cable run where interference exposure is greatest. A directional high-rate double twisted-pair construction adds a further architectural layer of noise cancellation. Precision machined pewter-finish locking metal ends with channel identification, locking split-tip connectors, no solder joints, moulded strain reliefs, and C3 Tech (Continuous Connection Construction) complete the build. Key Specifications SKU: SI8217 Series: 8000 Series Channels: 2 Length: 17 feet (5 metres) Conductor: Oversized silver-plated copper Conductors per channel: 3 (positive, negative, signal drain) Total conductors: 6 Construction: Directional high-rate double twisted-pair Shielding: Triple-braided + Mylar foil Connector type: Locking split-tip RCA Connector finish: Pewter Connector end: Precision machined locking metal with channel ID Solder joints: None Strain relief: Moulded Outer jacket: Black mesh protective Construction method: C3 Tech (Continuous Connection Construction) Warranty: Not specified — confirm with Stinger Features & Benefits 17-Foot Length — Full Vehicle Run for Larger Vehicles At 17 feet (5 metres), the SI8217 provides sufficient length for boot-mounted amplifier installations in SUVs, wagons, and vans where a 12-foot cable falls short. The additional length allows for clean routing along the full B-pillar-to-boot path, with slack to avoid tight bends at cable entry points. Oversized Silver-Plated Copper Conductors Oversized silver-plated copper combines the high-frequency precision of silver with the current-carrying capacity of copper — delivering tight, controlled bass response and crystal-clear high-frequency detail across the full 20Hz–20kHz audio spectrum and beyond. Over a 17-foot run, conductor quality has a measurably greater impact on signal integrity than over a short run. Triple-Braided + Mylar Shielding — Critical Over Long Runs A 17-foot cable has significantly more exposure to electromagnetic interference than a 6-foot cable — passing along a greater portion of the vehicle's wiring, alternator, and ignition interference sources. Three independent braided layers cascade over each other, with each covering any gaps in the layer beneath, combined with an inner Mylar foil layer for multi-directional noise rejection from both radiated and conducted sources. Three Conductors per Channel — True Channel Separation Dedicated positive, negative, and signal drain conductors per channel separate the shield drain from the audio signal return — eliminating the noise interaction that occurs when these paths share a single conductor in a standard two-conductor design. Directional High-Rate Double Twisted-Pair Construction The directional double twisted-pair winding is orientated to maximise noise cancellation when signal flows from source unit to amplifier. Directional markings indicate correct orientation. The architectural noise cancellation of the twisted-pair geometry is particularly effective over longer cable runs. C3 Tech — No Breaks Over the Full 17 Feet Stinger's C3 (Continuous Connection Construction) ensures no breaks, solder joints, or resistance discontinuities throughout the entire 17-foot length — providing consistent signal transfer from end to end. Locking Split-Tip Connectors + Pewter Precision Machined Ends Spring-tension locking split-tip connectors resist vibration-induced loosening in the automotive environment. Pewter-finished precision machined metal ends with channel identification markings ensure correct left/right routing and corrosion-resistant contact at both ends. Technical Specs Specification Detail Brand Stinger SKU SI8217 Series 8000 Series Channels 2 Length 17 feet (5 metres) Conductor Oversized Silver-Plated Copper Conductors per Channel 3 (positive, negative, signal drain) Total Conductors 6 Construction Directional High-Rate Double Twisted-Pair Shielding Triple-Braided + Mylar Foil Connector Type Locking Split-Tip RCA Connector Finish Pewter Connector Ends Precision Machined Locking Metal, Channel ID Solder Joints None Strain Relief Moulded Outer Jacket Black Mesh Protective Construction Method C3 Tech Warranty Not confirmed — confirm with Stinger Compatible With / Goes Well With Suitable for: 2-channel amplifier and subwoofer monoblock installations in larger vehicles where the full routing distance from head unit to boot-mounted amplifier exceeds 12 feet SUVs, wagons, vans, and larger utes where additional cable length is needed to clear obstacles in the routing path High-performance amplifier installations where signal cable quality must match the amplifier's capability Pairs well with: Rockford Fosgate, Hertz, Morel, and AudioControl amplifiers Stinger SI82YF and SI82YM 8000 Series Y-adapters for consistent system build across all RCA connections Stinger SI8212 (12ft / 3.7m) for shorter vehicle runs in the same 8000 Series specification Length selection guide: SI826 (6ft / 1.8m) — amplifier in close proximity to head unit. SI8212 (12ft / 3.7m) — standard boot-mounted installation in compact to mid-size vehicles. SI8217 (17ft / 5m) — larger vehicles and longer routing paths. Frequently Asked Questions What is the difference between the SI8217 and the SI8212? Both are identical in specification, construction, and performance — same 8000 Series triple-braided shielding, silver-plated conductors, locking connectors, and C3 Tech. The only difference is length: SI8217 is 17 feet (5m) for larger vehicles, SI8212 is 12 feet (3.7m) for compact to mid-size vehicles. Select based on your vehicle's measured routing distance. What does triple-braided shielding provide that a standard single braid does not? Three independent braided layers cascade over each other — each covering any gaps in the layer beneath — achieving dramatically higher total shield coverage than a single braid. Combined with the inner Mylar foil layer, the shielding system rejects both radiated external interference and conducted internal noise simultaneously. This is particularly important over a 17-foot run. Why does the SI8217 use three conductors per channel rather than two? Standard RCA cables combine the negative signal return and shield drain into one conductor per channel. The SI8217 separates these into dedicated individual conductors, providing a lower-impedance signal return and isolating the shield drain from the audio signal — reducing the noise interaction that occurs in a standard two-conductor design. What is the benefit of locking split-tip connectors over standard push-fit RCA connectors? Standard push-fit RCA connectors rely on friction and can loosen under vibration, causing intermittent noise or signal dropout. The SI8217's locking split-tip connectors mechanically grip the socket with spring tension, providing a vibration-resistant hold that maintains consistent contact force over time in the automotive environment. What does the directional construction mean, and how should I orient the cable? The directional double twisted-pair winding cancels noise most effectively when signal flows from source unit to amplifier. Directional markings on the cable indicate the correct orientation. Installing in reverse does not damage the cable but reduces the effectiveness of the directional noise cancellation — particularly relevant over a longer 17-foot run. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

X1 Series 2-Channel Speaker Wire to RCA Adapter Connects OEM Head Unit Speaker Outputs to Amplifier RCA Inputs. Eliminates Line Output Converter on Compatible Amplifiers. Product Overview The Stinger X12LINE is a 2-channel RCA-to-speaker-wire adapter from the X1 Series designed for use with amplifiers that feature a balanced or differential-balanced input design. These amplifiers accept high-level speaker-level signals directly through their RCA input connections, removing the requirement for a standalone line output converter in compatible factory system integration scenarios. The X12LINE provides bare speaker wire leads at the source end for connection to the factory head unit's speaker output wiring, and 2-channel male RCA plugs at the amplifier end for direct connection to the amplifier's RCA inputs. Finished in black. Key Specifications SKU: X12LINE Series: X1 Series Configuration: Male RCA plugs to bare speaker wire leads Channels: 2 Colour: Black Compatible amplifiers: Balanced or differential-balanced RCA input design only Wire length: Not specified — confirm with Stinger Warranty: Not specified — confirm with Stinger Features & Benefits Eliminates Line Output Converter on Compatible Amplifiers Amplifiers with balanced or differential-balanced input designs accept high-level speaker signals through their RCA inputs without damage. The X12LINE provides the physical connection needed to bridge the factory head unit's speaker outputs directly to these amplifier inputs — reducing component count, wiring complexity, and installation cost compared to a dedicated LOC module. RCA Male to Bare Speaker Wire Configuration The amplifier end terminates in 2-channel male RCA plugs for direct connection to the amplifier's RCA inputs. The source end terminates in bare speaker wire leads that splice into the factory head unit's existing speaker output wiring — no additional connectors or adapters required. 2-Channel — Front, Rear, or Subwoofer Routing The 2-channel output covers stereo front or rear speaker pair integration. In compatible configurations, the two channels can also route a summed mono subwoofer signal from the factory head unit's speaker outputs to a monoblock amplifier's RCA input — where the amplifier's internal summing combines the channels as required. Compact, Simplified Installation A single adapter replaces a standalone LOC module and its associated wiring in compatible installations — reducing the number of components behind the dash and simplifying the integration of an aftermarket amplifier with a factory head unit. Technical Specs Specification Detail Brand Stinger SKU X12LINE Series X1 Series Configuration Male RCA to Bare Speaker Wire Channels 2 Colour Black Compatible Input Type Balanced / Differential-Balanced RCA Input Only Wire Length Not specified Warranty Not specified Compatible With / Goes Well With Suitable for: Amplifiers with balanced or differential-balanced input designs that explicitly support high-level input via RCA connections OEM factory head unit integration without a standalone line output converter Stereo front or rear speaker pair signal routing Mono subwoofer signal routing from factory speaker outputs to a compatible monoblock amplifier Compatible amplifier ranges (confirm high-level RCA input capability before purchasing): Rockford Fosgate amplifiers with confirmed high-level RCA input support AudioControl amplifiers with confirmed high-level RCA input support Other brands that list high-level RCA input capability in their specifications Amplifier compatibility is the critical check: The X12LINE will only work correctly with amplifiers that explicitly list high-level or speaker-level input as a supported function through the RCA connections. If the amplifier's specifications do not confirm this, a dedicated line output converter such as the Rockford Fosgate RF-HLC or RF-HLC4 is required instead. Frequently Asked Questions Can the X12LINE be used with any amplifier? No — the X12LINE is designed specifically for amplifiers with balanced or differential-balanced input designs that explicitly support high-level speaker-level signals through their RCA connections. Using this adapter with a standard amplifier that does not support high-level RCA input can damage the amplifier's input stage. What is a balanced or differential-balanced amplifier input, and why does it matter? A balanced or differential-balanced input processes the positive and negative signals independently, using the difference between them to reconstruct the audio signal and cancel common-mode noise. This architecture allows the input to accept the higher voltage levels from speaker outputs without damage, while simultaneously rejecting noise introduced by the high-level source connection. Does the X12LINE replace a line output converter entirely? In compatible installations — yes. When the amplifier supports high-level input through its RCA connections, the X12LINE provides the adapter needed to connect the factory speaker wire directly to the amplifier RCA inputs. If the amplifier does not support high-level RCA input, a dedicated line output converter is still required. How do I connect the speaker wire end of the X12LINE to the factory wiring? The bare speaker wire leads splice into the factory head unit's speaker output wiring — positive wire to each channel's positive speaker output, negative wire to each channel's negative. Refer to the vehicle's wiring diagram or the head unit's installation manual to identify the correct speaker output wires. Is the X12LINE suitable for subwoofer signal routing from a factory head unit? Yes, in compatible configurations. The 2-channel output can route a summed mono subwoofer signal from the factory head unit's speaker outputs to a monoblock amplifier's RCA input, provided the amplifier supports high-level RCA input. The amplifier's internal summing or mono input configuration combines the two channels as required. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

9-Inch Trapezoid Head Unit Fascia Volkswagen Golf MK6 (Including GTI) 2009–2013. OEM-Style Dashboard Integration. Fascia Panel Only. Not Compatible with MK5 or MK7. Product Overview The Stinger SF9-VW03 is a vehicle-specific 9-inch trapezoid head unit fascia designed for the Volkswagen Golf MK6, including GTI variants, manufactured between 2009 and 2013. Engineered for the Golf MK6 factory dash opening, the SF9-VW03 delivers a clean, OEM-style integration for a 9-inch trapezoid head unit upgrade without gaps, misalignment, or modification required. Compatible with 9-inch trapezoid head units from Alpine, Kenwood, Pioneer, Mongoose, and Aerpro. Not compatible with the Golf MK5 or MK7, which have different dashboard openings and mounting configurations. Key Specifications SKU: SF9-VW03 Brand: Stinger Product type: 9-inch trapezoid head unit fascia Compatible head unit format: 9-inch trapezoid Colour: Not specified — confirm with Stinger Vehicle: Volkswagen Golf MK6 (incl. GTI) 2009–2013 Not compatible with: Golf MK5 or MK7 Includes: Fascia panel only Wiring harness: Not included — sold separately SWC harness: Not included — sold separately Camera adaptor: Not included — sold separately Antenna adaptor: Not included — sold separately USB adaptor: Not included — sold separately Features & Benefits Purpose-Built for VW Golf MK6 — Including GTI Engineered specifically for the Golf MK6 (2009–2013) factory dashboard opening, the SF9-VW03 delivers a precise OEM-style fit that cannot be achieved with a universal fascia. The GTI variant is explicitly confirmed compatible. MK6 Specific — Not for MK5 or MK7 The SF9-VW03 covers the Golf MK6 (2009–2013) only. The Golf MK5 and MK7 have different dashboard openings and mounting configurations and require separate fascia solutions. 9-Inch Trapezoid Format — Wide Head Unit Compatibility Supports the trapezoid 9-inch format used by Alpine (INE-AW409S, INE-AX809), Kenwood (DMX80AXS), Mongoose (Q9WCA), Pioneer (DMH-AP6650BT), and Aerpro (AM9X). Clean OEM-Style Finish Fills the Golf MK6 factory dashboard opening cleanly — maintaining the factory interior aesthetic with a professional-quality appearance after installation. Fascia Panel Only — Installer Flexibility Supplied as the fascia panel alone, allowing installers to source the correct harness and accessories for the vehicle's specific equipment level and chosen head unit. Technical Specs Specification Detail Brand Stinger SKU SF9-VW03 Product Type 9-Inch Trapezoid Head Unit Fascia Compatible Format 9-Inch Trapezoid Colour Not specified — confirm with Stinger Vehicle Volkswagen Golf MK6 (incl. GTI) 2009–2013 Not Compatible Golf MK5 or MK7 Compatible Head Units Alpine INE-AW409S, INE-AX809; Kenwood DMX80AXS; Mongoose Q9WCA; Pioneer DMH-AP6650BT; Aerpro AM9X Wiring Harness Not included SWC Harness Not included Camera Adaptor Not included Antenna Adaptor Not included USB Adaptor Not included Compatible With / Goes Well With Vehicle compatibility: Make Model Year Range Notes Volkswagen Golf (incl. GTI) 2009–2013 MK6 Compatible 9-inch trapezoid head units: Alpine INE-AW409S / INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Recommended accessories (sold separately): VW Golf MK6-specific wiring harness VW Golf MK6 SWC harness and adaptors Antenna adaptor for Volkswagen vehicles CAC HEXT1.5M ISO Canbus extension cable harness Frequently Asked Questions Is the SF9-VW03 compatible with the Golf GTI? Yes — the SF9-VW03 is confirmed compatible with the Volkswagen Golf MK6 including GTI variants manufactured between 2009 and 2013. Is this fascia compatible with the Golf MK5 or MK7? No — the SF9-VW03 is designed for the Golf MK6 (2009–2013) only. The Golf MK5 and MK7 have different dashboard openings and mounting configurations and require separate fascia solutions. Does the SF9-VW03 include a wiring harness or any adaptors? No — the SF9-VW03 is a fascia panel only. No wiring harness, SWC harness, camera adaptor, antenna adaptor, or USB adaptor is included. Source the appropriate Golf MK6-specific accessories separately to complete the installation. Which 9-inch head units are confirmed compatible with the SF9-VW03? The SF9-VW03 is confirmed compatible with Alpine INE-AW409S, Alpine INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT, and Aerpro AM9X. Confirm your chosen head unit uses the standard 9-inch trapezoid mounting format before purchasing. Is professional installation recommended for the SF9-VW03? Yes — professional installation by a qualified car audio technician is recommended to ensure correct fascia fitment, secure head unit mounting, and proper wiring harness and adaptor connections including any CANbus integration required for the Golf MK6. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less