Professional twin-cylinder performance for rapid tyre inflation and heavy-duty 4WD applications The Oricom AIR40 Twin Cylinder Air Compressor delivers 130 litres per minute airflow through dual 40mm bore cylinders, providing the sustained high-volume output needed for large 4WD tyres, multiple simultaneous inflations, and extended duty cycles. This heavy-duty 12V compressor handles demanding offroad scenarios where rapid reinflation after beach driving, sand tracks, or rock crawling is critical to maintaining travel schedules. The twin-cylinder configuration distributes heat and workload across two pistons, enabling a 45-minute continuous duty cycle before requiring a 20-minute rest period—significantly longer than single-cylinder alternatives. Maximum pressure reaches 300 PSI with 150 PSI working pressure, suitable for both standard passenger tyres and larger light truck applications. The system includes automatic pressure cut-out between 120-150 PSI, thermal protection shutting down at 115°C, and a washable air filter reducing maintenance requirements. A 6-metre hose with NPT quarter-inch quick-connect fitting provides reach across dual-axle setups, while direct battery connection via included wiring loom delivers the 62-amp current draw required for peak performance. Compatible with Oricom's tyre inflator and deflator kits for comprehensive pressure management, this compressor meets Australian safety standards and carries a three-year warranty. Key Specifications Twin cylinder design with 40mm bore diameter Maximum airflow: 130 L/min at 0 PSI, 112 L/min at 29 PSI, 108 L/min at 40 PSI Maximum pressure: 300 PSI Maximum working pressure: 150 PSI Voltage: 12-13.8V DC Current draw: 62A under load, 35A no load Duty cycle: 45 minutes continuous operation, 20 minutes rest Automatic pressure cut-out: 120-150 PSI Thermal protection: Auto shut-off at 115°C Washable air filter included 6-metre hose with NPT ¼" quick-connect Dimensions: 29 × 24.5 × 12 cm Weight: 10.2 kg Includes 40A inline fuse and wiring loom 3-year warranty Meets AS/NZS 60335.1:2020+A1:2021 and EN/IEC 55014-1:2021 EMC standards Features & Benefits Twin-Cylinder Architecture — Dual 40mm cylinders distribute heat and mechanical stress, delivering sustained high airflow while extending operational lifespan compared to single-cylinder compressors under equivalent loads. 130 L/min Maximum Airflow — High-volume output inflates 35-inch 4WD tyres from 18 PSI to 36 PSI in under five minutes per tyre, critical when time-sensitive travel schedules follow beach or sand track deflation. Extended 45-Minute Duty Cycle — Continuous operation for 45 minutes before mandatory rest enables complete reinflation of dual-axle trailer or caravan setups without mid-process cooling interruptions. 300 PSI Maximum Pressure Capability — Handles not only standard tyre inflation but also air locker activation, air suspension adjustments, and high-pressure accessories beyond typical compressor limits. Automatic Pressure Cut-Out — Shuts off between 120-150 PSI, preventing over-inflation damage to tyres and allowing unattended operation when paired with inflation kits or manifold systems. Thermal Protection at 115°C — Automatic overheat shutdown protects motor windings during extreme ambient temperatures or extended use, preventing permanent damage from thermal overload. Washable Air Filter — Reusable filter element reduces ongoing maintenance costs and prevents airborne dust ingress in harsh Australian conditions, maintaining compressor efficiency over years of service. 6-Metre Hose Reach — Extended hose length eliminates vehicle repositioning when inflating dual-axle caravans, trailers, or reaching across wide 4WD track widths during simultaneous multi-tyre inflation. Direct Battery Connection — Heavy-duty wiring loom with 40A inline fuse connects directly to battery terminals, bypassing cigarette lighter sockets inadequate for 62-amp peak current draw. NPT Quick-Connect Fitting — Standard quarter-inch NPT connection provides compatibility with Oricom inflator/deflator kits, tyre gauges, and aftermarket inflation accessories. Technical Specs Model: AIR40 Configuration: Twin cylinder Cylinder Bore Diameter: 40 mm Operating Voltage: 12-13.8V DC Current Draw (Under Load): 62A Current Draw (No Load): 35A Inline Fuse Rating: 40A (supplied) Maximum Pressure: 300 PSI Maximum Working Pressure: 150 PSI Airflow Rate (0 PSI): 130 L/min Airflow Rate (29 PSI): 112 L/min Airflow Rate (40 PSI): 108 L/min Duty Cycle: 45 minutes on, 20 minutes rest Pressure Cut-Out: Automatic at 120-150 PSI Thermal Protection: Auto shut-off at 115°C Air Filter: Washable, reusable Hose Length: 6 m Hose Connector: NPT ¼" quick-connect Battery Connection: Direct wiring loom (included) Dimensions: 29 × 24.5 × 12 cm Weight: 10.2 kg Safety Standards: AS/NZS 60335.1:2020+A1:2021, EN/IEC 55014-1:2021 EMC compliant Warranty: 3 years Frequently Asked Questions Can I run this compressor from my cigarette lighter socket? No, the AIR40 draws 62 amps under load, far exceeding typical 10-15 amp cigarette lighter circuit ratings. Direct battery connection via the included wiring loom is required for safe operation. What happens if I exceed the 45-minute duty cycle? The thermal protection system automatically shuts down the compressor at 115°C to prevent motor damage. Allow 20 minutes cooling before resuming operation to avoid repeated thermal shutdowns. Will this compressor work with my Oricom MTDI4 quad inflator kit? Yes, the AIR40 is specifically noted as compatible with Oricom's tyre inflator and deflator systems via the NPT quarter-inch quick-connect fitting standard across their product range. How often do I need to clean the air filter? Filter cleaning frequency depends on operating environment. Dusty outback conditions may require monthly cleaning, while sealed-road use extends intervals to quarterly or longer. Visual inspection guides maintenance timing. Can this compressor fill air suspension or activate air lockers? Yes, the 300 PSI maximum pressure and 150 PSI working pressure accommodate both air suspension adjustments and air locker activation, though dedicated air tanks improve response times for lockers. Compatible With Oricom MTDI4 quad tyre inflator/deflator kit Oricom MTDI2 twin tyre inflator/deflator kit 4WD vehicles with dual-battery systems Caravan and dual-axle trailer setups Vehicles with air suspension systems Air locker-equipped differentials NPT quarter-inch inflation accessories Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Portable single-cylinder performance with digital pressure control for efficient 4WD inflation The Oricom AIR30 Portable Air Compressor delivers 75 litres per minute airflow through a 44mm bore single-cylinder design, providing reliable inflation capability for standard 4WD tyres, offroad adventures, and touring applications. This portable 12V compressor handles beach recovery, sand track transitions, and campsite tyre management with a compact design that stores easily in the included heavy-duty carry case. Maximum pressure reaches 150 PSI with 120 PSI working pressure, suitable for passenger vehicle and light 4WD applications. The system includes a digital pressure gauge with automatic shut-off functionality, eliminating manual monitoring during inflation and preventing over-pressure situations. An automatic pressure cut-out switch activates between 90-120 PSI, while thermal protection shuts down at 115°C to prevent motor damage during extended use. The 6-metre hose with NPT quarter-inch quick-connect provides reach across vehicle widths, and the 2.5-metre power cable with battery clamps connects directly to your battery for reliable 32-amp current delivery. The 20-minute duty cycle with 40-minute rest period suits sequential tyre inflation during typical offroad pressure adjustments. Compatible with Oricom's tyre inflator and deflator kits, this compressor meets Australian safety standards and carries a three-year warranty. Key Specifications Single cylinder with 44mm bore diameter Maximum airflow: 75 L/min at 0 PSI, 50 L/min at 29 PSI, 42 L/min at 40 PSI Maximum pressure: 150 PSI Maximum working pressure: 120 PSI Voltage: 12-13.8V DC Current draw: 32A under load, 17A no load Duty cycle: 20 minutes continuous operation, 40 minutes rest Automatic pressure cut-out: 90 PSI on, 120 PSI off Thermal protection: Auto shut-off at 115°C Air filter included Digital pressure gauge with auto shut-off 6-metre hose with NPT ¼" quick-connect 2.5-metre power cable with battery clamps Dimensions: 35 × 29.5 × 16 cm Weight: 7.3 kg Heavy-duty carry case included 40A inline fuse supplied 3-year warranty Meets AS/NZS 60335.1:2020+A1:2021 and EN/IEC 55014-1:2021 EMC standards Features & Benefits Digital Gauge with Auto Shut-Off — Set target pressure and walk away—the digital gauge automatically stops inflation when reached, preventing over-inflation and allowing unattended operation during multi-tyre setups. 75 L/min Maximum Airflow — Single-cylinder design delivers sufficient volume for standard 4WD tyres, inflating 33-inch tyres from 18 PSI to 32 PSI in approximately 4-6 minutes per tyre. Portable Heavy-Duty Case — Complete system stores in rugged carry case with organized compartments, protecting components during transport and keeping inflation gear accessible in vehicle storage areas. 20-Minute Duty Cycle — Continuous operation for 20 minutes handles typical four-tyre sequential inflation from beach or sand track pressures back to highway specifications before requiring rest. 150 PSI Maximum Pressure — Handles standard passenger and light 4WD tyre inflation requirements, suitable for most touring and recreational offroad applications without exceeding typical pressure needs. Thermal Protection at 115°C — Automatic overheat shutdown protects motor during high ambient temperatures or extended use, preventing permanent damage and ensuring longevity in Australian conditions. 6-Metre Hose Reach — Extended hose length reaches all four tyres on most vehicles without repositioning, streamlining the inflation process during roadside or campsite pressure adjustments. Direct Battery Connection — 2.5-metre cable with battery clamps provides reliable power delivery for the 32-amp current draw, bypassing cigarette lighter socket limitations inadequate for compressor loads. NPT Quick-Connect Fitting — Standard quarter-inch NPT connection ensures compatibility with Oricom inflator/deflator kits, tyre gauges, and aftermarket inflation accessories without adapter requirements. Compact 7.3kg Package — Lighter than twin-cylinder alternatives while maintaining capability for typical 4WD inflation tasks, balancing performance with storage convenience and portability. Technical Specs Model: AIR30 Configuration: Single cylinder Cylinder Bore Diameter: 44 mm Operating Voltage: 12-13.8V DC Current Draw (Under Load): 32A Current Draw (No Load): 17A Inline Fuse Rating: 40A (supplied) Maximum Pressure: 150 PSI Maximum Working Pressure: 120 PSI Airflow Rate (0 PSI): 75 L/min Airflow Rate (29 PSI): 50 L/min Airflow Rate (40 PSI): 42 L/min Duty Cycle: 20 minutes on, 40 minutes rest Pressure Cut-Out: 90 PSI on, 120 PSI off Thermal Protection: Auto shut-off at 115°C Air Filter: Included Digital Gauge: With automatic shut-off function Hose Length: 6 m Hose Connector: NPT ¼" quick-connect Power Cable Length: 2.5 m with battery clamps Carry Case: Heavy-duty case included Dimensions: 35 × 29.5 × 16 cm Weight: 7.3 kg Safety Standards: AS/NZS 60335.1:2020+A1:2021, EN/IEC 55014-1:2021 EMC compliant Warranty: 3 years Frequently Asked Questions Can I use this compressor to inflate all four tyres without stopping? The 20-minute duty cycle allows sequential inflation of four standard tyres from typical beach pressures (18-20 PSI) to highway pressures (32-36 PSI), though you may approach the duty limit. Monitor compressor temperature and allow rest if needed. How does the digital gauge auto shut-off work? Set your target pressure on the digital gauge before starting inflation. The gauge monitors pressure and automatically stops the compressor when the target is reached, preventing over-inflation without manual monitoring. Will this work with my Oricom MTDI2 twin inflator kit? Yes, the AIR30 is specifically noted as compatible with Oricom's tyre inflator and deflator systems via the NPT quarter-inch quick-connect fitting standard across their product range. Can I connect this to my cigarette lighter socket? No, the AIR30 draws 32 amps under load, exceeding typical 10-15 amp cigarette lighter circuit ratings. The included 2.5m cable with battery clamps is designed for direct battery connection. What's the difference between this and the AIR40 twin cylinder? The AIR30 offers 75 L/min single-cylinder performance suitable for standard 4WD use, while the AIR40 provides 130 L/min twin-cylinder output for faster inflation, longer duty cycles (45 minutes), and heavier-duty applications. Compatible With Oricom MTDI2 twin tyre inflator/deflator kit Oricom MTDI4 quad tyre inflator/deflator kit Oricom TDD01 digital tyre deflator 4WD vehicles and touring setups Beach driving and sand track applications Standard passenger vehicles requiring portable inflation NPT quarter-inch inflation accessories Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Compact single-cylinder performance with integrated digital control for efficient portable inflation The Oricom AIR20 Portable Air Compressor delivers 70 litres per minute airflow through a 40mm bore single-cylinder design, providing reliable inflation capability for 4WD tyres, touring applications, and general vehicle maintenance. This portable 12V compressor handles beach recovery, sand track transitions, and recreational offroad pressure adjustments with a compact 5.8kg package that stores in the included carry bag. Maximum pressure reaches 200 PSI with 150 PSI working pressure, suitable for standard passenger vehicles and light 4WD applications. The integrated backlit digital pressure gauge displays real-time pressure readings and provides automatic shut-off when the target pressure is reached, eliminating manual monitoring during inflation. An automatic pressure switch activates between 120-150 PSI, while thermal protection shuts down at 115°C to prevent motor damage during extended use. The 7.5-metre hose with NPT quarter-inch quick-connect provides extended reach across vehicle widths, and the 3-metre power cable with battery clamps connects directly to your battery for reliable 32-amp current delivery. The 30-minute duty cycle with 30-minute rest period suits typical four-tyre inflation sequences during offroad pressure adjustments. The system includes three inflation nozzles for versatile applications and a washable air filter for ongoing maintenance. Meeting Australian safety standards with a three-year warranty, this compressor balances portability with practical inflation capability. Key Specifications Single cylinder with 40mm bore diameter Maximum airflow: 70 L/min at 0 PSI, 50 L/min at 29 PSI, 48 L/min at 40 PSI Maximum pressure: 200 PSI Maximum working pressure: 150 PSI Voltage: 12-13.8V DC Current draw: 32A under load, 18A no load Duty cycle: 30 minutes continuous operation, 30 minutes rest Automatic shut-off: Upon reaching display-set pressure Automatic pressure switch: 120-150 PSI Thermal protection: Auto shut-off at 115°C Washable air filter included Integral backlit digital pressure gauge 7.5-metre hose with NPT ¼" quick-connect 3-metre power cable with battery clamps Dimensions: 30 × 13.5 × 19 cm Weight: 5.8 kg Carry bag included 3× inflation nozzles included 40A inline fuse supplied 3-year warranty Meets AS/NZS 60335.1:2020+A1:2021 and EN/IEC 55014-1:2021 EMC standards Features & Benefits Integrated Backlit Digital Display — Built-in digital gauge with backlight allows accurate pressure monitoring in low-light conditions, automatically stopping inflation when target pressure is reached without manual intervention. 70 L/min Maximum Airflow — Single-cylinder design delivers sufficient volume for standard 4WD and passenger vehicle tyres, inflating typical 33-inch tyres from 18 PSI to 32 PSI in approximately 5-7 minutes per tyre. Extended 7.5-Metre Hose — Longest hose in the Oricom compressor range reaches all four tyres on most vehicles without repositioning, plus provides extended reach for dual-axle trailer applications. 30-Minute Duty Cycle — Balanced 30-minute operation and 30-minute rest cycle handles complete four-tyre inflation from beach or sand pressures back to highway specifications with minimal waiting. 200 PSI Maximum Pressure — Higher pressure capability compared to entry-level compressors handles standard tyre inflation plus higher-pressure applications like sports equipment or specialty inflation tasks. Compact 5.8kg Package — Lightest in the Oricom compressor lineup while maintaining capability for typical touring and recreational offroad inflation, maximizing storage convenience and portability. Washable Air Filter — Reusable filter element reduces ongoing maintenance costs and prevents airborne dust ingress in harsh Australian conditions, maintaining compressor efficiency over extended service life. Thermal Protection at 115°C — Automatic overheat shutdown protects motor during high ambient temperatures or extended duty cycles, preventing permanent damage and ensuring longevity in outback conditions. Direct Battery Connection — 3-metre cable with battery clamps provides reliable power delivery for 32-amp current draw, bypassing cigarette lighter socket limitations inadequate for compressor loads. Versatile Inflation Nozzles — Three included nozzles expand functionality beyond tyre inflation to sports balls, inflatable camping gear, and recreational equipment for multi-purpose touring applications. Technical Specs Model: AIR20 Configuration: Single cylinder Cylinder Bore Diameter: 40 mm Operating Voltage: 12-13.8V DC Current Draw (Under Load): 32A Current Draw (No Load): 18A Inline Fuse Rating: 40A (supplied) Maximum Pressure: 200 PSI Maximum Working Pressure: 150 PSI Airflow Rate (0 PSI): 70 L/min Airflow Rate (29 PSI): 50 L/min Airflow Rate (40 PSI): 48 L/min Duty Cycle: 30 minutes on, 30 minutes rest Automatic Shut-Off: Upon reaching pressure set on display Automatic Pressure Switch: 120-150 PSI Thermal Protection: Auto shut-off at 115°C Air Filter: Washable, reusable Digital Gauge: Integral backlit display with auto shut-off Hose Length: 7.5 m Hose Connector: NPT ¼" quick-connect Power Cable Length: 3 m with battery clamps Carry Bag: Included Inflation Nozzles: 3× included Dimensions: 30 × 13.5 × 19 cm Weight: 5.8 kg Safety Standards: AS/NZS 60335.1:2020+A1:2021, EN/IEC 55014-1:2021 EMC compliant Warranty: 3 years Frequently Asked Questions How does the automatic shut-off work on the digital display? Set your target pressure using the integrated digital gauge before starting inflation. The gauge monitors pressure continuously and automatically stops the compressor when the target is reached, preventing over-inflation without manual monitoring. Can I use this compressor at night or in low-light conditions? Yes, the digital display features backlighting for visibility in low-light conditions, making it suitable for roadside inflation after dark or early morning departures when ambient light is limited. Will the 30-minute duty cycle handle all four tyres? The 30-minute duty cycle typically handles sequential inflation of four standard tyres from typical beach pressures (18-20 PSI) to highway pressures (32-36 PSI), though larger tyres or lower starting pressures may approach the duty limit. What are the three inflation nozzles used for? The included nozzles adapt the compressor for inflating sports balls, camping mattresses, inflatable boats, and other recreational equipment beyond vehicle tyre applications, expanding versatility for touring use. Can I connect this to my cigarette lighter socket? No, the AIR20 draws 32 amps under load, exceeding typical 10-15 amp cigarette lighter circuit ratings. The included 3m cable with battery clamps is designed for direct battery connection only. Compatible With Oricom tyre inflator and deflator kits Oricom TDD01 digital tyre deflator 4WD vehicles and touring setups Passenger vehicles requiring portable inflation Beach driving and sand track applications Recreational camping and touring equipment NPT quarter-inch inflation accessories Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on modern Isuzu models The Oricom BBR007 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Isuzu D-MAX (2021 onwards) and Isuzu MU-X (2022 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 5mm high-grade stainless steel and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to Isuzu bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a work ute for site communications, preparing a touring rig for convoy travel, or equipping a remote area vehicle for emergency communications, this bracket provides the foundation for reliable UHF antenna mounting on late-model Isuzu platforms. Key Specifications Vehicle Compatibility: Isuzu D-MAX (2021+), Isuzu MU-X (2022+) Material: High-grade stainless steel Material Thickness: 5mm Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2021+ D-MAX and 2022+ MU-X bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 5mm Stainless Steel Construction — Heavy-gauge stainless steel provides rigid antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Isuzu's design without requiring specialized equipment or professional fabrication services. Technical Specs Model: BBR007 Compatible Vehicles: Isuzu D-MAX 2021 onwards, Isuzu MU-X 2022 onwards Construction Material: High-grade stainless steel Material Thickness: 5mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit earlier D-MAX or MU-X models? No, the BBR007 is specifically engineered for D-MAX 2021+ and MU-X 2022+ models. Earlier generation vehicles have different bonnet profiles and may require different bracket models. Verify your vehicle's manufacture year before purchase. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Will the powder coating chip or fade over time? Quality powder coating provides excellent durability, though stone chips and extreme abrasion may cause localized damage over time. Touch-up paint can address minor chips to maintain corrosion protection. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Isuzu D-MAX (2021, 2022, 2023, 2024, 2025 model years) Isuzu MU-X (2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on late-model Mazda BT-50 The Oricom BBR006 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Mazda BT-50 (2021 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 5mm high-grade stainless steel and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to BT-50 bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a work ute for site communications, preparing a touring rig for convoy travel, or equipping a remote area vehicle for emergency communications, this bracket provides the foundation for reliable UHF antenna mounting on late-model Mazda platforms. Key Specifications Vehicle Compatibility: Mazda BT-50 (2021+) Material: High-grade stainless steel Material Thickness: 5mm Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2021+ BT-50 bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 5mm Stainless Steel Construction — Heavy-gauge stainless steel provides rigid antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Mazda's design without requiring specialized equipment or professional fabrication services. Technical Specs Model: BBR006 Compatible Vehicles: Mazda BT-50 2021 onwards Construction Material: High-grade stainless steel Material Thickness: 5mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit earlier BT-50 models? No, the BBR006 is specifically engineered for BT-50 2021+ models. Earlier generation vehicles have different bonnet profiles and may require different bracket models. Verify your vehicle's manufacture year before purchase. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Will the powder coating chip or fade over time? Quality powder coating provides excellent durability, though stone chips and extreme abrasion may cause localized damage over time. Touch-up paint can address minor chips to maintain corrosion protection. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Mazda BT-50 (2021, 2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on Nissan Navara NP300 The Oricom BBR005 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Nissan Navara NP300 (2015 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 5mm high-grade stainless steel and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to NP300 bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a work ute for site communications, preparing a touring rig for convoy travel, or equipping a remote area vehicle for emergency communications, this bracket provides the foundation for reliable UHF antenna mounting on the popular NP300 platform. Key Specifications Vehicle Compatibility: Nissan Navara NP300 (2015+) Material: High-grade stainless steel Material Thickness: 5mm Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2015+ Navara NP300 bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 5mm Stainless Steel Construction — Heavy-gauge stainless steel provides rigid antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Nissan's design without requiring specialized equipment or professional fabrication services. Technical Specs Model: BBR005 Compatible Vehicles: Nissan Navara NP300 2015 onwards Construction Material: High-grade stainless steel Material Thickness: 5mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit D22 or D40 Navara models? No, the BBR005 is specifically engineered for NP300 models from 2015 onwards. Earlier D22 and D40 generation vehicles have different bonnet profiles and require different bracket models. Verify your vehicle's model designation before purchase. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Will the powder coating chip or fade over time? Quality powder coating provides excellent durability, though stone chips and extreme abrasion may cause localized damage over time. Touch-up paint can address minor chips to maintain corrosion protection. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Nissan Navara NP300 (2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on late-model Nissan Patrol Y62 The Oricom BBR004 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Nissan Patrol Y62 (2020 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 5mm high-grade stainless steel and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to Y62 bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a touring wagon for remote area travel, preparing a family adventure vehicle for convoy communications, or equipping a station vehicle for outback work, this bracket provides the foundation for reliable UHF antenna mounting on the flagship Patrol platform. Key Specifications Vehicle Compatibility: Nissan Patrol Y62 (2020+) Material: High-grade stainless steel Material Thickness: 5mm Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2020+ Patrol Y62 bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 5mm Stainless Steel Construction — Heavy-gauge stainless steel provides rigid antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Nissan's design without requiring specialized equipment or professional fabrication services. Technical Specs Model: BBR004 Compatible Vehicles: Nissan Patrol Y62 2020 onwards Construction Material: High-grade stainless steel Material Thickness: 5mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit earlier Y62 Patrol models before 2020? No, the BBR004 is specifically engineered for Y62 models from 2020 onwards. Earlier Y62 variants or previous generation Patrol models (Y61, GU) have different bonnet profiles and require different bracket models. Verify your vehicle's manufacture year before purchase. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Will the powder coating chip or fade over time? Quality powder coating provides excellent durability, though stone chips and extreme abrasion may cause localized damage over time. Touch-up paint can address minor chips to maintain corrosion protection. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Nissan Patrol Y62 (2020, 2021, 2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on Toyota Hilux The Oricom BBR003 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Toyota Hilux (2015 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 6mm high-grade stainless steel—the thickest in the BBR series—and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to Hilux bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a work ute for site communications, preparing a touring rig for convoy travel, or equipping a remote area vehicle for emergency communications, this bracket provides the foundation for reliable UHF antenna mounting on Australia's most popular 4WD platform. Key Specifications Vehicle Compatibility: Toyota Hilux (2015+) Material: High-grade stainless steel Material Thickness: 6mm (heaviest-duty in BBR range) Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2015+ Hilux bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 6mm Stainless Steel Construction — Heaviest-gauge stainless steel in the BBR series provides maximum rigidity and antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Toyota's design without requiring specialized equipment or professional fabrication services. Heavy-Duty Hilux Application — Extra thickness accommodates the demanding usage patterns common to Australia's best-selling 4WD, from mine site work trucks to remote touring rigs. Technical Specs Model: BBR003 Compatible Vehicles: Toyota Hilux 2015 onwards Construction Material: High-grade stainless steel Material Thickness: 6mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit older Hilux models before 2015? No, the BBR003 is specifically engineered for Hilux models from 2015 onwards. Earlier generation vehicles have different bonnet profiles and require different bracket models. Verify your vehicle's manufacture year before purchase. Why is this bracket thicker than other BBR models? The 6mm thickness provides additional rigidity for the Hilux platform, which commonly experiences heavy-duty usage in work, touring, and mining applications requiring maximum bracket strength and durability. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Toyota Hilux (2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Heavy-duty bonnet mounting for secure UHF antenna installation on Toyota's flagship 4WD The Oricom BBR002 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Toyota LandCruiser 300 Series (2021 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 6mm high-grade stainless steel—matching the heavy-duty specification of the Hilux BBR003—and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to LC300 bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a touring wagon for remote area travel, preparing a family expedition vehicle for convoy communications, or equipping a station vehicle for outback work, this bracket provides the foundation for reliable UHF antenna mounting on Toyota's premium 4WD platform. Key Specifications Vehicle Compatibility: Toyota LandCruiser 300 Series (2021+) Material: High-grade stainless steel Material Thickness: 6mm (heavy-duty specification) Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Vehicle-Specific Engineering — Purpose-designed fitment for 2021+ LandCruiser 300 Series bonnet profiles ensures correct positioning, secure mounting, and professional appearance without universal bracket compromises. 6mm Stainless Steel Construction — Heavy-gauge stainless steel provides maximum rigidity and antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Toyota's design without requiring specialized equipment or professional fabrication services. Premium Platform Application — Heavy-duty 6mm thickness accommodates the demanding usage patterns of Australia's premier touring and expedition vehicle platform. Technical Specs Model: BBR002 Compatible Vehicles: Toyota LandCruiser 300 Series 2021 onwards Construction Material: High-grade stainless steel Material Thickness: 6mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit the LandCruiser 200 Series or earlier models? No, the BBR002 is specifically engineered for the 300 Series from 2021 onwards. The 200 Series and earlier generations have different bonnet profiles and require different bracket models. Verify your vehicle's series designation before purchase. Why does this bracket use 6mm steel instead of 5mm? The 6mm thickness provides additional rigidity appropriate for the LandCruiser 300 Series platform, which commonly experiences heavy-duty touring, expedition, and remote area usage requiring maximum bracket strength and durability. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and expedition applications. Compatible With Toyota LandCruiser 300 Series (2021, 2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Vehicle-specific bonnet mounting for secure UHF antenna installation on late-model Ford platforms The Oricom BBR001 Bonnet Mount Bracket provides a factory-engineered mounting solution specifically designed for Ford Ranger and Ford Everest (2022 onwards) models. This heavy-duty bracket enables secure installation of UHF CB antennas and compatible communication accessories directly to the bonnet, positioning the antenna for optimal transmission and reception without drilling into the roof or requiring complex mounting modifications. Constructed from 5mm high-grade stainless steel and finished with a black powder coating, the bracket withstands Australian offroad conditions including corrugations, dust, water crossings, and salt exposure. The vehicle-specific design ensures proper fitment to Ranger and Everest bonnet contours and bolt patterns, delivering a professional appearance that integrates cleanly with the vehicle's lines. Installation requires basic hand tools and follows the existing bonnet structure, avoiding permanent vehicle modifications. Whether fitting out a work ute for site communications, preparing a touring rig for convoy travel, equipping a family wagon for remote area adventures, or setting up an expedition vehicle for emergency communications, this bracket provides the foundation for reliable UHF antenna mounting on Ford's popular 4WD platforms. Key Specifications Vehicle Compatibility: Ford Ranger (2022+), Ford Everest (2022+) Material: High-grade stainless steel Material Thickness: 5mm Finish: Black powder coating Application: UHF CB antenna mounting and compatible accessories Installation: Bonnet-mounted (vehicle-specific design) Warranty: 12 months Features & Benefits Dual-Vehicle Compatibility — Engineered to suit both Ford Ranger and Ford Everest models from 2022 onwards, leveraging shared platform architecture for versatile application across Ford's 4WD lineup. 5mm Stainless Steel Construction — Heavy-gauge stainless steel provides rigid antenna support under high-speed highway travel, offroad vibration, and harsh environmental exposure without flexing or corroding. Black Powder Coat Finish — Durable powder coating protects against stone chips, UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for a factory-style appearance. Bonnet Mounting Position — Locates UHF antenna forward of the cabin for improved transmission patterns and reception characteristics compared to rear-mounted or bumper-mounted alternatives. No Roof Drilling Required — Eliminates permanent roof penetrations that risk water leaks, structural compromise, or warranty concerns, while maintaining vehicle resale value and interior headliner integrity. Corrosion-Resistant Design — Stainless steel core with powder coat protection handles coastal environments, river crossings, and tropical humidity common in Australian touring conditions. Simple Installation Process — Bolts to existing bonnet structure using basic hand tools, following Ford's design without requiring specialized equipment or professional fabrication services. Technical Specs Model: BBR001 Compatible Vehicles: Ford Ranger 2022 onwards, Ford Everest 2022 onwards Construction Material: High-grade stainless steel Material Thickness: 5mm Surface Finish: Black powder coating Mounting Location: Vehicle bonnet Primary Application: UHF CB antenna mounting Secondary Compatibility: Other compatible communication accessories Installation Method: Bolt-on (vehicle-specific) Warranty Period: 12 months Frequently Asked Questions Will this bracket fit earlier Ranger or Everest models before 2022? No, the BBR001 is specifically engineered for Ranger and Everest models from 2022 onwards. Earlier generation vehicles have different bonnet profiles and require different bracket models. Verify your vehicle's manufacture year before purchase. Does the same bracket fit both Ranger and Everest? Yes, the BBR001 is designed to fit both vehicles as they share the same platform architecture and bonnet design from 2022 onwards. Does this bracket come with mounting hardware? Mounting hardware specifications not provided by manufacturer. Verify hardware inclusion with supplier before purchase, or source appropriate stainless steel bolts and washers for installation. Can I mount accessories other than UHF antennas? The bracket is designed primarily for UHF CB antenna mounting but may accommodate other compatible communication accessories. Verify accessory weight and mounting pattern compatibility before installation. Does bonnet mounting affect antenna performance compared to roof mounting? Bonnet mounting provides effective UHF transmission for most applications, though roof-mounted antennas typically offer slightly better omnidirectional patterns. Bonnet mounting eliminates roof drilling while maintaining practical communication range for touring and work applications. Compatible With Ford Ranger (2022, 2023, 2024, 2025 model years) Ford Everest (2022, 2023, 2024, 2025 model years) UHF CB antennas (standard mounting patterns) Oricom and aftermarket UHF communication systems GME, Uniden, and other UHF CB equipment Verify specific antenna mounting requirements and bracket compatibility before installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Genuine replacement antenna pole in pink finish for ANU916 UHF CB antenna systems The Oricom ANT916PNK is a factory-specification 3dBi replacement antenna pole designed exclusively for the Oricom ANU916 UHF CB antenna system. This pink-finished antenna pole restores full communication functionality when the original pole is damaged, worn, or lost, maintaining the distinctive appearance of pink-accented communication setups. The 3dBi gain specification matches the original ANU916 antenna performance characteristics, ensuring consistent transmission and reception quality after replacement. Suitable for 4WD enthusiasts, touring operators, and recreational users who want to maintain or customize their ANU916 antenna with a pink colour option, this genuine Oricom spare part eliminates compatibility concerns associated with aftermarket alternatives. Whether replacing a damaged pole after offroad impacts, refreshing a weathered antenna, or customizing a vehicle's communication gear appearance, this pole provides direct-fit replacement capability for ANU916 systems. Key Specifications Genuine Oricom replacement part (ANT916PNK) Antenna Gain: 3dBi Colour: Pink Compatibility: Oricom ANU916 UHF CB antenna system only Direct replacement—no adapters or modifications required Features & Benefits Genuine Oricom Design — Factory-engineered for the ANU916 system, ensuring proper electrical characteristics, mechanical fit, and performance matching the original antenna specification. 3dBi Gain Specification — Maintains the original antenna performance characteristics after replacement, preserving communication range and signal quality for convoy coordination and offroad communications. Pink Colour Finish — Distinctive pink finish provides visual customization option or matches existing pink-themed vehicle accessories and communication gear. Direct Replacement — Plug-and-play installation means quick antenna restoration without technical modifications, getting your UHF system back operational immediately. Durable Construction — Built to Oricom's standards for Australian conditions, handling the knocks, vibrations, and weather exposure common to 4WD and touring applications. Technical Specs Model: ANT916PNK Antenna Type: UHF CB antenna pole (replacement) Gain: 3dBi Colour: Pink Compatibility: Oricom ANU916 antenna system Application: Replacement pole only (base/mount sold separately) Frequently Asked Questions Is this antenna pole compatible with other Oricom antenna models? The ANT916PNK is specifically designed for the ANU916 antenna system. Compatibility with other Oricom models is not confirmed and should be verified before purchase. Does this include the antenna base or mounting hardware? No, this is the antenna pole only. The base, mounting hardware, and coaxial cable are sold separately or remain from your existing ANU916 installation. What is the difference between this and the standard ANU916 antenna pole? The ANT916PNK features a pink colour finish while maintaining identical electrical and mechanical specifications to the standard ANU916 antenna pole. Can I use this pole with aftermarket antenna bases? This pole is engineered specifically for Oricom ANU916 bases. Using with aftermarket bases may result in improper fit, electrical mismatch, or performance degradation. How do I know if my antenna needs pole replacement? Replace the pole if you observe physical damage, corrosion at connection points, reduced transmission range, or reception quality degradation compared to known-good antennas. Compatible With Oricom ANU916 UHF CB antenna base (required, sold separately) Oricom UHF CB radios and communication systems 4WD vehicles with existing ANU916 installations Note: This is a replacement pole only. ANU916 antenna base required for operation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Durable fiberglass antenna with heavy-duty spring base for reliable 4WD communications The Oricom ANU916 3dBi UHF CB Antenna delivers reliable communication performance through a detachable fiberglass whip design with integrated heavy-duty barrel spring base. This 640mm antenna system (including spring) combines the flexibility needed to survive offroad impacts with the rigidity required for consistent signal transmission. The fiberglass radome construction withstands branch strikes, car wash encounters, and low-clearance obstacles without permanent damage, while the barrel spring base absorbs impacts that would break fixed-mount antennas. The detachable pole design simplifies replacement after damage and enables quick removal for secure storage or height-restricted areas. Complete with 4.5-metre low-loss coaxial cable, pre-terminated FME connector, and PL259 adaptor, the ANU916 provides everything needed for installation on 4WD vehicles, heavy vehicles, and touring setups. The black powder-coated finish integrates cleanly with modern vehicle aesthetics while protecting against corrosion in Australian conditions. Whether coordinating convoy travel, maintaining worksite communications, or ensuring emergency contact capability in remote areas, this antenna balances durability with practical 3dBi gain performance. Key Specifications Antenna Gain: 3dBi Total Length: 640mm (including spring base) Construction: Fiberglass radome with detachable pole Base Type: Heavy-duty barrel spring Coaxial Cable: 4.5m low-loss cable included Connector: Pre-terminated FME connector with PL259 adaptor Mounting: Grub screw attachment (grub screw and hex key included) Finish: Black powder coating Warranty: 3 years Features & Benefits Detachable Fiberglass Whip — Remove the antenna pole for secure storage, car wash protection, or low-clearance situations, then reinstall quickly without tools or technical knowledge. Heavy-Duty Barrel Spring Base — Absorbs impacts from branches, obstacles, and offroad terrain, allowing the antenna to flex and return without damage that would break rigid-mount alternatives. 3dBi Gain Performance — Provides balanced transmission and reception characteristics suitable for convoy communications, worksite coordination, and general touring applications across typical UHF CB ranges. 640mm Overall Length — Compact profile reduces clearance concerns in garages, car washes, and low-hanging obstacles while maintaining effective signal propagation for practical communication distances. Fiberglass Radome Construction — Non-conductive fiberglass housing protects internal elements while providing flexibility and impact resistance superior to metal whip designs in demanding conditions. Complete Installation Kit — Includes 4.5-metre low-loss coaxial cable, pre-terminated FME connector, PL259 adaptor, grub screw, and hex key for immediate installation without sourcing additional components. Secure Grub Screw Mounting — Hex key-tightened grub screw ensures positive antenna retention under vibration and offroad conditions while allowing intentional removal when needed. Black Powder Coat Finish — Durable coating protects against UV degradation, salt corrosion, and chemical exposure while matching modern vehicle aesthetics for clean integration. Three-Year Warranty — Extended warranty coverage reflects manufacturer confidence in durability and construction quality for demanding Australian applications. Technical Specs Model: ANU916 Antenna Type: UHF CB whip antenna Gain: 3dBi Total Length: 640mm (including spring base) Pole Construction: Detachable fiberglass radome Base Type: Heavy-duty barrel spring Mounting Method: Grub screw with hex key (included) Coaxial Cable Length: 4.5m Cable Type: Low-loss coaxial Connector Type: Pre-terminated FME connector Adaptor Included: PL259 adaptor Surface Finish: Black powder coating Warranty Period: 3 years Frequently Asked Questions Can I replace just the antenna pole if it gets damaged? Yes, the fiberglass whip is detachable. Replacement poles like the ANT916PNK (pink) are available separately, allowing pole replacement without purchasing a complete antenna system. Will the spring base protect the antenna from all impacts? The heavy-duty barrel spring absorbs most typical offroad impacts from branches and obstacles, but extreme forces or direct strikes may still cause damage. The spring significantly improves survival compared to rigid mounts. What vehicles is this antenna suitable for? The ANU916 suits 4WD vehicles, utes, heavy vehicles, caravans, and touring setups requiring reliable UHF communications. Verify mounting location clearance and ensure proper antenna base installation. Do I need to purchase a separate antenna base or mount? The antenna includes a barrel spring base with grub screw mounting, but you'll need an appropriate UHF antenna mount or bracket (like Oricom BBR series bonnet brackets) to attach the antenna to your vehicle. How does 3dBi gain compare to higher-gain antennas? 3dBi antennas provide balanced omnidirectional performance suitable for general touring and convoy use. Higher-gain antennas (6dBi, 9dBi) offer increased range but with narrower vertical radiation patterns that may miss signals on undulating terrain. Compatible With Oricom BBR series bonnet brackets (BBR001-BBR007) Oricom UHF CB radios and communication systems 4WD vehicles, heavy vehicles, and touring setups Standard UHF antenna mounts and brackets ANT916PNK replacement pole (pink colour option) Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less