20 Foot (6 Metre) Twisted Pair RCA Signal Cable OFC, Platinum Ends, RFI/EMI Rejection, Split Center Pin, Frosted Woven Shield. The Rockford Fosgate RFI-20 is a 20-foot (6-metre) twisted pair RCA signal cable with woven outer shield OFC (Oxygen-Free Copper) conductors, platinum-plated ends, and split center pin for a secure connection. The twisted pair construction provides RFI and EMI noise rejection across the full cable length relevant for boot-to-dash amplifier runs in vehicles with alternators, ignition systems, and other interference sources. At 20 feet (6 metres), the RFI-20 is sufficient for most full-length vehicle installations from head unit to boot-mounted amplifiers, with cable routing through door sills or under carpet. Key Specifications Specification Detail Part Number RFI-20 Type RCA Signal Cable Length 20 feet (6 metres) ✓ Conductor OFC (Oxygen-Free Copper) ✓ End Plating Platinum ✓ Design Twisted Pair ✓ Shield Woven outer, frosted finish ✓ Noise Rejection RFI and EMI ✓ Center Pin Split for secure connection ✓ Channels Not confirmed — confirm stereo or mono from official product page Impedance Not specified Warranty Not specified Features & Benefits 20 Feet / 6 Metres — Full Vehicle Run Length — Sufficient for a complete head unit to boot amplifier run in most passenger vehicles, with routing and working length. Twisted Pair — RFI/EMI Rejection — Common-mode interference cancellation along the full cable length — important over longer runs where the cable passes near high-current wiring. OFC Conductors — Low-resistance, corrosion-resistant signal transfer. Platinum-Plated Ends — Reliable, corrosion-resistant RCA contact at both ends. Split Center Pin — Spring-tension engagement for vibration-resistant connection. Woven Frosted Shield — Physical protection and EMI shielding. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

8 AWG PC-OFC Amplifier Installation Kit 17ft Power Wire, 3ft Ground Wire, 20ft Remote Wire, AGU Fuse Holder and Fuse. Full AWG Specification. The Rockford Fosgate RFK8 is an 8 AWG complete amplifier power installation kit all the wiring components required for a single amplifier installation in one purchase. Full AWG specification, 100% Pure Crystal OFC (PC-OFC) power and ground wire at 8.36mm² with 735 strands, plus an AGU inline fuse holder and fuse, remote turn-on wire, and wire termination hardware. Kit Contents Item Specification Power wire 17 feet, 8 AWG PC-OFC ✓ Ground wire 3 feet, 8 AWG PC-OFC ✓ Remote wire 20 feet ✓ AGU fuse holder Included ✓ Fuse 40A ✓ (see note below) Termination hardware Included ✓ (type not specified)   Key Specifications Specification Detail Part Number RFK8 Wire Gauge 8 AWG ✓ Cross-Section 8.36mm² ✓ Strand Count 735 ✓ Conductor 100% PC-OFC ✓ AWG Compliance Full AWG specification ✓ Power Wire Length 17 feet ✓ Ground Wire Length 3 feet ✓ Remote Wire Length 20 feet ✓ Fuse Holder AGU inline ✓ Fuse Rating 40A ✓ (confirm if AGU or separate) Termination Hardware Included (type TBC) RCA Cable Included Not stated — confirm Warranty Not specified Features & Benefits Complete Single-Amplifier Kit — All primary wiring components in one purchase — power, ground, remote, and fuse protection. 8 AWG PC-OFC — Full Spec — 8.36mm² at 735 strands meets or exceeds full AWG specification. PC-OFC minimises grain boundary resistance. 17ft Power / 3ft Ground / 20ft Remote — Standard vehicle routing lengths for a boot-mounted amplifier. AGU Fuse Holder and Fuse Included — Overcurrent protection on the positive power run — no separate fuse holder purchase required. Termination Hardware Included — Confirm the hardware type (ring terminals etc.) from the official product page. FAQs What amplifier power is appropriate for 8 AWG wiring? 8 AWG is generally suitable for amplifiers rated up to approximately 500W RMS depending on cable run length and supply voltage. For higher-powered systems requiring 1/0 AWG, consider the Rockford Fosgate RFW1R-51 / RFW1B-51 wire spools and RFD1 distribution block instead. Is an RCA cable included? Not stated in the kit contents. Confirm from the official Rockford Fosgate RFK8 product page. If not included, a separate RCA signal cable from the RFI or RFIT range is required. What fuse is included? A 40A fuse and AGU fuse holder are confirmed in the kit. Whether the 40A fuse is the AGU type or a separate additional fuse is ambiguous in the supplier data — confirm from the official product page. How long is the remote wire? 20 feet — confirmed. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

4 AWG PC-OFC Amplifier Installation Kit 17ft Power Wire, 3ft Ground Wire, Maxi Fuse Holder and 100A Fuse. Full AWG Specification. The Rockford Fosgate RFK4 is a 4 AWG amplifier power installation kit the heavier-gauge counterpart to the RFK8, suited to higher-powered amplifier systems requiring 4 AWG wiring. Full AWG specification, 100% PC-OFC at 21.1mm² with 1,862 strands. Includes a Maxi-format (not AGU) inline fuse holder and a 100A fuse consistent with the higher current capacity of a 4 AWG system. Kit Contents Item Specification Power wire 17 feet, 4 AWG PC-OFC (21.1mm², 1,862 strands) ✓ Ground wire 3 feet, 4 AWG PC-OFC ✓ Remote wire Not stated Maxi fuse holder Included ✓ Fuse 100A ✓ (see ambiguity note) Termination hardware Included ✓ (type TBC)   Key Specifications Specification Detail Part Number RFK4 Wire Gauge 4 AWG ✓ Cross-Section 21.1mm² ✓ Strand Count 1,862 ✓ Conductor 100% PC-OFC ✓ AWG Compliance Full AWG spec ✓ Power Wire 17 feet ✓ Ground Wire 3 feet ✓ Remote Wire Not confirmed Fuse Holder Maxi inline ✓ Fuse Rating 100A ✓ RCA Cable Not included Warranty Not specified How It Differs From RFK8 Feature RFK8 RFK4 Wire Gauge 8 AWG (8.36mm²) 4 AWG (21.1mm²) ✓ Strand Count 735 1,862 ✓ Fuse Holder AGU Maxi ✓ Fuse Rating 40A 100A ✓ Remote Wire 20ft confirmed Not confirmed RCA Cable Not included Not included FAQs What amplifier power is the RFK4 suited to? 4 AWG wiring is generally appropriate for amplifiers rated approximately 500–1,000W RMS depending on cable run length. For systems above this range requiring 1/0 AWG, the Rockford Fosgate RFW1R-51 wire and RFD1 distribution block provide the appropriate gauge. Why does the RFK4 use a Maxi fuse holder instead of AGU? The Maxi format is a higher-current fuse type suited to 4 AWG main runs at 100A — consistent with the higher current capacity of 4 AWG wiring. The AGU fuse in the RFK8 is rated at 40A, appropriate for 8 AWG. Is remote wire included? Not confirmed in the supplier description — unlike the RFK8 which explicitly states 20ft of remote wire. Confirm from the official Rockford Fosgate RFK4 product page before purchasing. Is an RCA cable included? No — same as the RFK8. A separate RCA signal cable from the RFI or RFIT range is required. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

1/0 AWG PC-OFC Amplifier Installation Kit 17ft Power Wire, 3ft Ground Wire, ANL/Maxi Fuse Holder, 300A Fuse, 20ft Remote Wire. 1-Year Warranty. The Rockford Fosgate RFK1 is a 1/0 AWG single amplifier power installation kit the 1/0 AWG power-only counterpart to the RFK4 and RFK8. Full AWG specification, 100% PC-OFC at 53.5mm² with 4,704 strands identical conductor spec to the standalone RFW1R-51 and RFW1B-51 wire spools. Includes an ANL/Maxi inline fuse holder with 300A fuse, 20 feet of remote wire, and wire termination hardware. Confirmed 1-year warranty. Kit Contents Item Specification Power wire 17 feet, 1/0 AWG PC-OFC (53.5mm², 4,704 strands) ✓ Ground wire 3 feet ✓ — gauge not specified (confirm from official product page) Remote wire 20 feet ✓ ANL/Maxi fuse holder Included ✓ Fuse 300A ✓ (see ambiguity note) Termination hardware Included ✓ (type TBC) Key Specifications Specification Detail Part Number RFK1 Wire Gauge 1/0 AWG ✓ Cross-Section 53.5mm² ✓ Strand Count 4,704 ✓ Conductor 100% PC-OFC ✓ AWG Compliance Full AWG spec ✓ Power Wire 17 feet ✓ Ground Wire 3 feet (gauge TBC) ✓ Remote Wire 20 feet ✓ Fuse Holder ANL/Maxi ✓ Fuse Rating 300A ✓ RCA Cable Not included Warranty 1 Year ✓ Full Kit Range Comparison Kit Gauge Application Signal Fuse Warranty RFK8 8 AWG Single Power only AGU 40A TBC RFK8X 8 AWG Single Complete AGU 40A TBC RFK4 4 AWG Single Power only Maxi 100A TBC RFK4D 4 AWG Dual Complete Maxi 100A TBC RFK1 1/0 AWG Single Power only ANL/Maxi 300A 1 Year ✓ RFK1D 1/0 AWG Dual Complete TBC TBC FAQs What amplifier power suits the RFK1? 1/0 AWG at 53.5mm² is appropriate for high-power amplifier systems — typically single amplifiers rated above approximately 1,000W RMS, or installations where voltage drop over a long power run requires the lower resistance of 1/0 AWG. What fuse holder type is included? An ANL/Maxi inline fuse holder is confirmed — accepting both ANL and Maxi format fuses. The 300A fuse is also included. Consistent with the standalone RFFANL inline fuse holder in the accessories range. What is the ground wire gauge? Not specified in the supplier description. For a 1/0 AWG power run, a matching 1/0 AWG ground is standard practice. Confirm from the official Rockford Fosgate RFK1 product page. Is a warranty confirmed? Yes — 1 year confirmed. This is the clearest warranty confirmation in the installation kit range. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Universal Inline RCA Audio Level Control Audio Taper Potentiometer, Four Mounting Configurations: Panel Mount, Under-Dash Bracket, Rocker Switch with 3.5mm AUX, and Flush Panel Mount. Mobile, Marine, and Off-Road Compatible. Product Overview The Rockford Fosgate PLC-U is a universal inline stereo RCA level control designed to vary the signal level of any stereo pair of RCA cables independently of a master volume control. The high-quality audio taper potentiometer provides true linear level control across the entire knob range suited to subwoofer level adjustment, zone volume control, or anywhere a dedicated RCA signal path requires independent level management. The PLC-U ships with four mounting configurations covering the widest range of vehicle installation scenarios: standard 1" panel mount (large or small knob), universal under-dash bracket, rocker switch mount with integrated 3.5mm AUX-to-RCA extension port, and a disassembled rocker switch configuration for smaller flush panel mounting. Compatible with source units, line drivers, and amplifiers. Suitable for mobile, marine, and off-road applications. Key Specifications Part number: PLC-U Type: Inline stereo RCA audio level control ✓ Control: Audio taper potentiometer (linear) ✓ Signal path: Stereo RCA pair (inline) ✓ Mounting configurations: 4 ✓ Panel mount: 1" (25.4mm) hole, retaining nut, large and small knob options ✓ Under-dash bracket: Universal, used with panel mount unit ✓ Rocker switch mount: Integrated 3.5mm to RCA extension port ✓ Flush mount: Rocker switch disassembled for smaller-hole installation ✓ Rocker switch knockout: Fits standard vehicle rocker switch panel knockouts ✓ Compatible with: Source units, line drivers, amplifiers ✓ Applications: Mobile, marine, off-road ✓ Input/output impedance: Not specified — confirm with Rockford Fosgate Cable lengths: Not specified — confirm with Rockford Fosgate Dimensions: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits Audio Taper Potentiometer — True Linear Level Control The audio taper (logarithmic) potentiometer matches the non-linear sensitivity of human hearing — producing a level change that feels linear across the entire knob rotation, rather than changing rapidly at the lower end of the range as a standard linear potentiometer does. This provides precise, usable level adjustment from minimum to maximum. Panel Mount — 1" Hole, Large and Small Knob Installs in a standard 1" panel hole (same as the PAUX) with a threaded retaining nut. Two knob size options are included — large for easy manual adjustment during driving, small for a more discreet installation. The panel mount version is the primary configuration for dedicated level control locations on the dash or console. Universal Under-Dash Bracket When a panel cut-out is not preferred or clearance behind the panel is limited, the universal under-dash bracket holds the panel mount unit in an accessible under-dash position without requiring a hole. Rocker Switch Mount with 3.5mm AUX Extension The rocker switch configuration fits standard vehicle rocker switch panel knockouts (common in trucks, SUVs, and 4WDs with unused accessory switch positions). The integrated 3.5mm-to-RCA extension port adds AUX input capability at the same location — combining level control and device connectivity in a single rocker switch position. Flush Panel Mount via Disassembly Disassembling the rocker switch housing allows the level control potentiometer to be surface-mounted using a smaller hole than the 1" panel mount requires — enabling installation in locations where neither the 1" hole nor the full rocker switch knockout is available. Stereo RCA Inline — Universal System Compatibility Inline on any stereo pair of RCA cables — works with any source unit, line driver, or amplifier with RCA connections. Compatible with the full Rockford Fosgate RFI, RFIT, RFIY, and RFITY cable and adapter range. Technical Specs Specification Detail Brand Rockford Fosgate Part Number PLC-U Series Punch Type Inline Stereo RCA Level Control ✓ Control Audio Taper Potentiometer ✓ Signal Path Stereo RCA pair (inline) ✓ Mounting Options 4 configurations ✓ Panel Mount Hole 1 inch (25.4mm) ✓ Panel Mount Knobs Large and Small included ✓ Panel Mount Security Threaded retaining nut ✓ Under-Dash Bracket Universal, included ✓ Rocker Switch Mount Integrated 3.5mm to RCA extension ✓ Flush Mount Via rocker switch disassembly ✓ Rocker Knockout Fit Standard vehicle rocker switch positions ✓ Applications Mobile, Marine, Off-Road ✓ Input/Output Impedance Not confirmed Cable Lengths Not confirmed Dimensions Not confirmed Warranty Not confirmed Compatible With / Goes Well With Suitable for: Subwoofer level adjustment from an accessible dash or console location Zone volume control for secondary RCA output channels Any stereo RCA signal path requiring independent level management Marine, UTV, motorcycle, and off-road audio systems (marine-suitable application confirmed) Pairs well with: Rockford Fosgate RFI or RFIT series RCA cables (inline on the signal path) Rockford Fosgate TM750X1bd or TM1000X5ad marine amplifiers Rockford Fosgate RF-HLC or RF-HLC4 LOC units (downstream level control) Rockford Fosgate PAUX (the rocker switch AUX port extends similar functionality from a single mounting position) Frequently Asked Questions What is an audio taper potentiometer and why does it matter for level control? An audio taper (also called logarithmic) potentiometer is designed to match the non-linear sensitivity of human hearing — which perceives loudness changes logarithmically, not linearly. At any position on the knob, the level change feels proportional and smooth. A standard linear potentiometer would make most of its audible change in the first 20% of knob rotation, making fine adjustment difficult. Can the PLC-U be used as a subwoofer level control? Yes — the PLC-U controls the signal level on any inline stereo RCA pair. For subwoofer level adjustment, connect it inline on the RCA cable between the head unit or crossover output and the subwoofer amplifier input. Which mounting option suits a standard truck or 4WD with rocker switch panels? The rocker switch mount configuration — it fits standard vehicle rocker switch panel knockouts that are common in utes, trucks, and 4WDs. The integrated 3.5mm-to-RCA extension port adds AUX input capability at the same switch position, making this configuration particularly practical for dual-function installations. Does the PLC-U work in marine installations? Yes — the PLC-U is confirmed suitable for mobile, marine, and off-road applications. The rocker switch mounting option is particularly useful in marine helm consoles that feature standard rocker switch panel arrays. Is the PLC-U the same as the PLC2 remote mentioned in the amplifier listings? No — the PLC2 is a dedicated bass remote level control specific to compatible Rockford Fosgate amplifiers (including the TM750X1bd and TM1000X5ad). The PLC-U is a universal inline RCA level control that works with any amplifier or source — it is not amplifier-specific and does not require amplifier compatibility. Both provide level adjustment, but from different points in the signal chain. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate bdSYNC2 Class-BD Amplifier Sync Cable Strap Two Power Amplifiers Into One Mono Unit Product Overview The Rockford Fosgate bdSYNC2 is a purpose-built 6-foot (approximately 1.8 metre) male-to-male sync cable designed to strap two compatible Class-BD Power series amplifiers together to operate as a single, larger mono amplifier. Available on select Class-BD Power series models only, the bdSYNC2 is the hardware solution for system builders who need more mono output power than a single Class-BD amplifier can provide pairing two units to combine their output into a single high-power mono channel without requiring an additional amplifier of a different model. This is a specialist accessory for high-output Power series system builds. The bdSYNC2 is not a universal amplifier interconnect it is designed exclusively for Rockford Fosgate Power series Class-BD amplifiers and is only compatible with select models within that range. Confirm specific amplifier model compatibility with your supplier before purchasing. Key Specifications Type: Amplifier sync strap cable Compatible topology: Class-BD Power series amplifiers (select models only) Connector type: Male-to-male Cable length: 6 feet (approximately 1.8 metres) Function: Straps two Class-BD Power amplifiers together as one mono amplifier Compatible amplifiers: Select Rockford Fosgate Power Class-BD models confirm with supplier Shipping weight: Confirm with supplier Features & Benefits Strap two Class-BD Power amplifiers into one mono unit: The bdSYNC2 connects two compatible Class-BD Power series amplifiers in a strapped configuration, allowing them to operate together as a single, higher-output mono amplifier. This is the primary method for doubling the mono output power of a Class-BD Power series system without switching to a different amplifier platform an important capability for high-output subwoofer builds where a single amplifier's rated power is insufficient. 6-foot (approximately 1.8 metre) cable length: The 1.8 metre cable provides sufficient reach to connect two amplifiers mounted side-by-side or in close proximity in a standard boot or audio bay installation without creating excessive cable slack or requiring the amplifiers to be positioned unusually close together. Male-to-male connector: The bdSYNC2 uses a male-to-male connector design for direct plug-in connection between the two amplifiers' sync ports without requiring adaptor hardware. Purpose-designed for Class-BD topology: The bdSYNC2 is not a generic RCA or signal cable it is an amplifier synchronisation cable specifically engineered for the Class-BD operating requirements of compatible Rockford Fosgate Power series amplifiers. Using a standard signal cable in place of the bdSYNC2 for strapping is not appropriate and will not produce the correct strapped mono configuration. Select models only high-output system specialist accessory: The bdSYNC2 is available for select Class-BD Power series models, making it a specialist accessory for serious high-output system builds rather than a general-use amplifier accessory. Confirm compatibility with your specific amplifier model before purchasing. Technical Specs Specification Detail SKU bdSYNC2 Brand Rockford Fosgate Type Amplifier sync strap cable Compatible Topology Class-BD Power series amplifiers Connector Male-to-male Cable Length 6 feet (approx. 1.8 metres) Compatible Amplifiers Select Rockford Fosgate Power Class-BD models confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Select Rockford Fosgate Power series Class-BD amplifiers confirm specific compatible model pairs with your supplier before purchase High-output mono subwoofer system builds requiring more power than a single Class-BD amplifier provides Dual-amplifier boot and audio bay installations with sufficient space for two Class-BD Power series units side-by-side Frequently Asked Questions What does the bdSYNC2 cable do? The bdSYNC2 connects two compatible Rockford Fosgate Power Class-BD amplifiers together so they operate as a single, larger mono amplifier effectively doubling the available mono output power for high-output subwoofer builds where a single amplifier is insufficient. Which amplifiers is the bdSYNC2 compatible with? The bdSYNC2 is compatible with select Rockford Fosgate Power series Class-BD amplifiers only. Not all Class-BD Power series models support bdSYNC2 strapping confirm specific compatible model pairs with your supplier before purchasing. Can the bdSYNC2 be used with non-Class-BD Rockford Fosgate amplifiers? No. The bdSYNC2 is designed exclusively for Rockford Fosgate Power series Class-BD amplifiers. It is not compatible with Class-A/B, Class-D, Class-AD, Class-BD marine, or any other amplifier topology in the Rockford Fosgate range. How long is the bdSYNC2 cable? The bdSYNC2 is 6 feet long approximately 1.8 metres providing sufficient reach for two amplifiers mounted in close proximity in a standard boot or dedicated audio bay installation. Is the bdSYNC2 the same as a standard RCA interconnect cable? No. The bdSYNC2 is a purpose-built amplifier synchronisation cable engineered for Class-BD strapping it is not a standard RCA or signal cable. Do not substitute a standard signal cable for the bdSYNC2 when strapping two Class-BD amplifiers, as this will not produce the correct strapped mono configuration. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate PMX10C Punch Marine 10ft Extension Cable Short Run, Perfect Fit Product Overview The Rockford Fosgate PMX10C is a 10-foot (approximately 3.0 metre) extension cable designed to extend the reach of compatible Punch Marine remote controllers and display heads. Purpose-built for use with the PMX-8DH, PMX-1R, and PMX-0R, it gives you the additional length needed to mount your remote or display head in a more accessible location without the excess cable bulk of longer extension options. The PMX10C is the shortest cable in the Punch Marine extension range, making it the ideal choice for smaller vessels, compact powersport installations, and tight routing situations where a precise, neat cable run is the priority. Like all PMX extension cables, it is plug-and-play no cutting, splicing, or custom wiring required. Key Specifications Cable length: 10 feet (approximately 3.0 metres) Compatible with: PMX-8DH, PMX-1R, PMX-0R Application: Marine remote controller and display head extension Plug-and-play installation no cutting or splicing required Shortest cable option in the Rockford Fosgate Punch Marine extension range Features & Benefits 10-foot cable length: Provides approximately 3.0 metres of additional reach. The most compact option in the PMX extension cable range, ideal for smaller vessels and short routing distances where longer cables would create unnecessary bulk. Compatible with PMX-8DH, PMX-1R, and PMX-0R: Direct-fit accessory for Rockford Fosgate Punch Marine remotes and display heads. No adapters, splicing, or modifications required. Plug-and-play design: Connects directly between the source unit and compatible remote or display head. Clean, straightforward installation for DIY builders and professional installers alike. Purpose-built for marine environments: Part of the Rockford Fosgate Punch Marine accessory ecosystem, engineered for reliable signal transmission through the moisture, heat, and vibration conditions typical of Australian watercraft and powersport applications. Cleaner install on smaller vessels: Less cable to manage means a tidier, more professional-looking installation on jet skis, small tinnies, kayaks with audio systems, and compact UTVs. Technical Specs Specification Detail SKU PMX10C Brand Rockford Fosgate Cable Length 10 feet (approx. 3.0 metres) Compatible Devices PMX-8DH, PMX-1R, PMX-0R Installation Type Plug-and-play Application Marine remote/display head extension Connector Type Not specified confirm with supplier Warranty Confirm with supplier Compatible With Rockford Fosgate PMX-8DH Punch Marine digital media receiver Rockford Fosgate PMX-1R Punch Marine wired remote Rockford Fosgate PMX-0R Punch Marine remote Rockford Fosgate PMX16C and PMX25C extension cables (where a longer run is required) Smaller marine vessels: jet skis, tinnies, kayaks with audio systems, and small runabouts Compact powersport applications: ATVs, UTVs, and side-by-sides with short source-unit-to-dash distances Frequently Asked Questions What devices is the PMX10C compatible with? The PMX10C is confirmed compatible with the Rockford Fosgate PMX-8DH, PMX-1R, and PMX-0R. If you are unsure whether it suits your specific Punch Marine setup, confirm with your supplier before ordering. How long is the PMX10C extension cable? The PMX10C is 10 feet in length, which is approximately 3.0 metres making it the shortest and most compact option in the Rockford Fosgate Punch Marine extension cable range. How does the PMX10C compare to the PMX16C and PMX25C? The PMX10C is the shortest of the three options at approximately 3.0 metres. Choose the PMX16C (approx. 4.9 metres) or PMX25C (approx. 7.6 metres) if your installation requires a longer cable run between the source unit and remote mounting location. Does the PMX10C require any cutting or special wiring? No. The PMX10C is a plug-and-play extension cable that connects directly between your Rockford Fosgate source unit and compatible remote or display head without cutting, splicing, or modification. Is the PMX10C suitable for permanent marine installation? Yes. The PMX10C is part of the Rockford Fosgate Punch Marine accessory range, designed for the moisture and vibration conditions common in marine environments. Secure and route the cable carefully during installation to protect it from abrasion and water ingress. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate T1S1-12 Power 12" T1 Slim Single 1-Ohm Subwoofer T1 Performance, Shallow Depth, 1-Ohm Ready Product Overview The Rockford Fosgate T1S1-12 is a 12" slimline single 1-ohm subwoofer from the flagship Power T1 series, rated at 600W RMS and 1200W peak. The 1-ohm stable counterpart to the T1S2-12, it carries the complete T1 slimline technology stack in a single 1-ohm voice coil configuration presenting a direct 1-ohm load to the amplifier for maximum power extraction from 1-ohm stable mono amplifiers without any wiring configuration required. Like the T1S2-12, the T1S1-12 is purpose-engineered to deliver near-identical performance characteristics to the full-depth Power T1 range from a significantly shallower mounting depth, through the same suite of proprietary and patent-pending technologies: the slotted voice coil assembly with interior and exterior windings enabling long excursion travel, the split yoke pass-through motor technology, high-energy neodymium motor structure, encapsulating voice coil-to-former coupling, integrated copper cap heat-sinking shorting ring (IDHS), dual Nomex progressive spiders with integrated lead wires, and carbon fibre/PMI/glass fibre composite cone. Optimised for sealed enclosures. Detachable die-cast aluminium trim ring included; optional grille insert available separately. Key Specifications Driver size: 12" slimline Voice coil configuration: Single 1-ohm Power handling: 600W RMS / 1200W peak Motor structure: High-temp high-energy neodymium Voice coil: Dual wound 2.5"; interior and exterior windings (slotted assembly) Cone: Carbon fibre / PMI / glass fibre composite with aluminium dust cap Surround: Injection-moulded foam with VAST technology Spiders: Dual Nomex progressive with integrated lead wires Basket: Aluminium die-cast with integrated heat sink fins Shorting ring: Integrated copper cap heat-sinking (IDHS) Input terminals: Custom insulated push spring 10 AWG Pole piece: Vented Trim ring: Detachable die-cast aluminium (included) Grille: Optional insert (sold separately) Optimised for: Sealed enclosures Frequency response: Confirm with supplier Sensitivity: Confirm with supplier Xmax: Confirm with supplier Mounting depth: Confirm with supplier Cutout diameter: Confirm with supplier Features & Benefits Single 1-ohm voice coil direct 1-ohm load, zero wiring complexity: The defining differentiator from the T1S2-12. A single 1-ohm voice coil presents a direct 1-ohm load to any 1-ohm stable mono amplifier no parallel or series wiring decisions, no configuration required. The most direct path to maximum power output from a 1-ohm stable amplifier in a slimline 12" T1 driver. Proprietary slotted voice coil assembly with interior/exterior windings (patent pending): Enables long excursion travel from a reduced mounting depth the fundamental engineering challenge of slimline subwoofer design. The slotted assembly with dual winding configuration allows the voice coil to travel significantly further than a conventional shallow driver, generating the displacement needed for deep, high-output bass from a slim installation profile. Proprietary split yoke pass-through motor technology (patent pending): A motor architecture innovation that enables greater excursion travel within a slimmer overall assembly depth, working in combination with the slotted voice coil to produce T1-level bass performance from a shallow driver. High-temp high-energy neodymium motor structure: Neodymium magnets produce significantly stronger magnetic fields per unit mass than conventional ferrite magnets, enabling high motor force (BL) in the compact, lightweight motor assembly required for a slimline design delivering the sensitivity and power handling of a T1 driver from a reduced physical footprint. Encapsulating voice coil-to-former coupling technology (patent pending): Increases bonding surface area and strength between the voice coil and former, preventing delamination at the high excursion levels and sustained 600W RMS input the T1S1-12 is designed for. Integrated copper cap heat-sinking shorting ring (IDHS): Simultaneously reduces inductance variation across the excursion range (improving linearity and reducing distortion) and draws thermal energy away from the voice coil gap essential for sustained 600W RMS reliability in compact, sealed enclosure environments where heat accumulates rapidly. Carbon fibre/PMI/glass fibre composite cone with aluminium dust cap: A stiff, lightweight multi-material composite significantly stiffer than paper or polypropylene cones, maintaining pistonic accuracy across the extended excursion range the slotted assembly enables. PMI foam core adds internal damping to suppress cone resonances. Injection-moulded foam surround with VAST technology: VAST reclaims cone surface area at the surround attachment, maximising effective piston area in the 12" slimline format. The injection-moulded foam surround provides consistent, repeatable compliance across the full travel range. Dual Nomex progressive spiders with integrated lead wires: Dual progressive spiders provide linear restoring force symmetry across the extended excursion range. Integrated lead wires eliminate the traditional separate tinsel lead removing a common high-excursion failure point that is particularly critical in a slimline driver designed for long voice coil travel. Aluminium die-cast basket with integrated heat sink fins: The basket fins actively dissipate heat from the motor assembly during sustained high-power use a thermal management feature particularly important in compact sealed enclosure installations where back-panel heat accumulation is a reliability concern. Vented pole piece: Air channels through the pole piece reduce thermal compression and back-pressure behind the cone at high excursion levels, improving linearity and power handling consistency in sealed enclosure use. Custom insulated push spring 10 AWG terminals: Appropriate for the high current demands of a 600W RMS, 1-ohm system. Push-spring design allows fast, clean wiring without tools. Optimised for sealed enclosures: The T1S1-12 is specifically tuned for sealed enclosure use. Confirm recommended enclosure volume with Rockford Fosgate documentation before building to ensure the intended bass response is achieved. Detachable die-cast aluminium trim ring included: Provides a clean, finished installation appearance at the cutout. Detachable for bare-driver installations where a trim ring is not required. Optional grille insert available separately: Confirm compatible part number with your supplier for installations where driver protection is required. Technical Specs Specification Detail SKU T1S1-12 Brand Rockford Fosgate Driver Size 12" slimline Voice Coil Configuration Single 1-ohm Power Handling 600W RMS / 1200W peak Motor Structure High-temp high-energy neodymium Voice Coil Dual wound 2.5"; interior and exterior windings (slotted assembly) Voice Coil Coupling Encapsulating voice coil-to-former technology (patent pending) Motor Technology Proprietary split yoke pass-through (patent pending) Cone Carbon fibre / PMI / glass fibre composite Dust Cap Aluminium Surround Injection-moulded foam with VAST technology Spiders Dual Nomex progressive with integrated lead wires Basket Aluminium die-cast with integrated heat sink fins Shorting Ring Integrated copper cap heat-sinking (IDHS) Pole Piece Vented Input Terminals Custom insulated push spring 10 AWG Trim Ring Detachable die-cast aluminium (included) Grille Optional insert (sold separately) Enclosure Optimisation Sealed Frequency Response Confirm with supplier Sensitivity Confirm with supplier Xmax Confirm with supplier Mounting Depth Confirm with supplier Cutout Diameter Confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Mono amplifiers stable at 1 ohm, rated at or near 600W RMS Rockford Fosgate Power T1 and T2 series mono amplifiers (1-ohm stable) Custom sealed enclosures designed for the T1S1-12 confirm recommended sealed enclosure volume with Rockford Fosgate documentation before building Vehicles where traditional-depth subwoofers will not fit: behind-seat ute and truck installations, shallow boot floor vehicles, and custom fabrication builds with depth constraints Rockford Fosgate T1S-1X12 slim sealed loaded enclosure (purpose-built slim sealed enclosure in the T1 slimline range) Rockford Fosgate 10 AWG and heavy-gauge wiring kits for 1-ohm mono amplifier installation Rockford Fosgate RCA cables and signal processors Frequently Asked Questions What is the difference between the T1S1-12 and T1S2-12? Both are 12" T1 slimline subwoofers with identical 600W RMS power handling and the same complete T1 slimline technology stack. The T1S1-12 has a single 1-ohm voice coil presenting a direct 1-ohm load, while the T1S2-12 has a single 2-ohm voice coil presenting a direct 2-ohm load. Choose the T1S1-12 when your amplifier is 1-ohm stable and 1-ohm wiring is the system target; choose the T1S2-12 for 2-ohm stable amplifier pairings. What impedance does the T1S1-12 present to the amplifier? The T1S1-12 is a single 1-ohm voice coil driver, presenting a direct 1-ohm load. No wiring configuration is required connect a 1-ohm stable mono amplifier rated at or near 600W RMS directly to the 10 AWG push spring terminals. How does the T1S1-12 achieve T1-level bass performance in a slimline format? The T1S1-12 uses a proprietary slotted voice coil assembly with interior and exterior windings (patent pending) enabling long excursion travel from a reduced mounting depth, combined with a split yoke pass-through motor technology (patent pending) and high-energy neodymium motor structure. These technologies together allow the T1S1-12 to deliver near-identical performance characteristics to a traditional-depth Power T1 subwoofer from a significantly shallower installation profile. What enclosure type is the T1S1-12 optimised for? The T1S1-12 is specifically optimised for sealed enclosures. Confirm recommended sealed enclosure volume with official Rockford Fosgate documentation or a qualified installer before designing or building an enclosure to ensure the intended bass response is achieved. Is a grille included with the T1S1-12? No. The T1S1-12 ships with a detachable die-cast aluminium trim ring only. An optional grille insert is available separately confirm the compatible part number with your supplier before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10" P3 4-Ohm DVC Subwoofer 500W RMS, Anodised Aluminium Cone, VAST, Dual Spider, FlexFit Basket, Extended Pole Piece. Product Overview The Rockford Fosgate Punch P3D4-10 is a 10" 4-Ohm Dual Voice Coil (DVC) subwoofer rated at 500W RMS the 4-Ohm variant of the P3 10" platform. Identical construction to the P3D2-10 with the sole difference being 4-Ohm voice coil impedance per coil, providing wiring options of 2-Ohm (parallel), 8-Ohm (series), or 4-Ohm per coil for bi-amplification no 1-Ohm stability requirement. Optimised for sealed and vented enclosures. Sold as an individual unit. The P3 series introduces the anodised aluminium cone and dustcap of the P3 platform the same premium cone material as the P3D2-10. Full confirmed specifications (sensitivity, Fs, Xmax, enclosure volumes) are not provided in the supplier data for this SKU confirm from the official Rockford Fosgate P3D4-10 datasheet. Physical dimensions on the same 10" P3 platform should be consistent with the P3D2-10 (232mm cutout, 156.8mm mounting depth) but must be independently confirmed before publishing. Key Specifications Subwoofer size: 10 inch Voice coil configuration: Dual Voice Coil (DVC) Impedance: 4-Ohm per coil (2-Ohm parallel / 8-Ohm series / 4-Ohm biamp) Power handling (RMS): 500W (confirmed) Power handling (peak): Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate (P3D2-10: 82dB) Fs: Not specified — confirm with Rockford Fosgate (P3D2-10: 26.6Hz) Xmax: Not specified — confirm with Rockford Fosgate (P3D2-10: 15.2mm) Cutout diameter: Not specified for this SKU — confirm with Rockford Fosgate (P3D2-10: 232mm) Mounting depth: Not specified for this SKU — confirm with Rockford Fosgate (P3D2-10: 156.8mm) Voice coil diameter: Not specified — confirm with Rockford Fosgate Cone: Anodised aluminium ✓ Dustcap: Anodised aluminium ✓ Voice coil: High-temp, Nomex® reinforcement collar ✓ Spider: Dual linear with embedded 16 AWG tinsel leads ✓ Basket: Hybrid StampCast, FlexFit, with integrated spider venting ✓ Pole piece: Extended ✓ Backplate: Bumped and vented ✓ Input terminals: Features: push — confirmed compression on P3D2-10 spec table Trim ring: Diamond-cut cast aluminium (grille insert compatible) ✓ Magnet cover: Protective PVC textured ✓ Enclosure compatibility: Sealed and vented ✓ CEA-2031 compliant: Not confirmed for this SKU — confirm with Rockford Fosgate Sealed enclosure volume: Not specified for this SKU — confirm with Rockford Fosgate Vented enclosure volume: Not specified for this SKU — confirm with Rockford Fosgate Sold as: Individual unit Warranty: Confirmed (authorised dealer) — terms TBC Features & Benefits 4-Ohm DVC — Broad Amplifier Compatibility: 2-Ohm (parallel): Most common configuration 8-Ohm (series): For amplifiers with higher minimum impedance 4-Ohm per coil (biamp): Each coil to a separate amplifier channel 500W RMS — Confirmed 500W RMS — the highest power handling in the Punch series catalogue. Anodised Aluminium Cone and Dustcap — Aluminium's rigidity resists cone breakup at high excursion. Anodising hardens the surface and provides heat conduction from the voice coil. See the P3D2-10 listing for a full explanation of the P3 cone upgrade. Dual Linear Spider — Two spiders for improved suspension compliance and cone control at high excursion levels. VAST — Up to 25% increased effective cone area at the same basket diameter. Hybrid StampCast Basket with FlexFit — Combined rigidity and reduced resonance; FlexFit for non-standard mounting cavity profiles. Nomex® Voice Coil Collar — Thermal and mechanical reinforcement at the voice coil junction — essential for sustained 500W operation. Extended Pole Piece and Bumped Vented Backplate — Extended pole for increased Xmax; vented backplate eliminates air spring compression. Diamond-Cut Cast Aluminium Trim Ring — Premium machined aluminium with grille insert provision. Rubberised Over-Mould — Grip feature on the basket for handling during installation. Technical Specs Specification Detail Brand Rockford Fosgate Part Number P3D4-10 Series Punch P3 Subwoofer Size 10 inch Voice Coil Dual Voice Coil (DVC) Impedance per Coil 4-Ohm ✓ Wiring Options 2-Ohm (parallel) / 8-Ohm (series) / 4-Ohm biamp ✓ Power Handling (RMS) 500W ✓ Peak Power Not confirmed — confirm with Rockford Fosgate Sensitivity Not confirmed — confirm with Rockford Fosgate Fs / Xmax / Qts Not confirmed — confirm with Rockford Fosgate Cutout Diameter Not confirmed — confirm with Rockford Fosgate Mounting Depth Not confirmed — confirm with Rockford Fosgate Sealed Enclosure Vol. Not confirmed — confirm with Rockford Fosgate Vented Enclosure Vol. Not confirmed — confirm with Rockford Fosgate Cone Anodised Aluminium ✓ Dustcap Anodised Aluminium ✓ Voice Coil High-Temp, Nomex® Collar ✓ Spider Dual Linear, Embedded 16 AWG Tinsel Leads ✓ Basket Hybrid StampCast, FlexFit, Spider Venting ✓ Pole Piece Extended ✓ Backplate Bumped and Vented ✓ Input Terminals Features: push — confirmed compression on P3D2-10 spec Trim Ring Diamond-Cut Cast Aluminium (Grille Compatible) ✓ Magnet Cover Protective PVC Textured ✓ Enclosure Type Sealed and Vented ✓ CEA-2031 Compliant Not confirmed for this SKU Sold As Individual Unit Warranty Confirmed (authorised dealer) — terms TBC Compatible With / Goes Well With Suitable enclosure types: Sealed and vented — both confirmed Wiring: 2-Ohm → parallel 8-Ohm → series 4-Ohm per coil → biamp Pairs well with: Rockford Fosgate T1500-1BDCP or T2500-1BDCP — confirm RMS output at 2-Ohm matches 500W Frequently Asked Questions What is the difference between P3D4-10 and P3D2-10? Both are identical 10" Punch P3 subwoofers at 500W RMS with the same aluminium cone construction. The sole difference is impedance: P3D4-10 is 4-Ohm per coil (2-Ohm parallel / 8-Ohm series), P3D2-10 is 2-Ohm per coil (1-Ohm parallel / 4-Ohm series). The 4-Ohm DVC avoids the 1-Ohm parallel requirement, providing broader amplifier compatibility. What enclosure size does the P3D4-10 require? Full specifications are not provided for the P3D4-10 in the supplier data. Based on the P3D2-10 (same 10" P3 platform): sealed 16.7L / 0.59 cu ft; vented 39.6L / 1.4 cu ft. Confirm with Rockford Fosgate that these volumes apply to the P3D4-10 before building or selecting an enclosure. What amplifier power is appropriate? 500W RMS at the selected impedance — 2-Ohm (parallel) or 4-Ohm (biamp). Confirm amplifier RMS output at the chosen load. Is a grille available? The diamond-cut cast aluminium trim ring accommodates an optional grille insert. Confirm the SKU with Rockford Fosgate. Does the P3D4-10 have the same aluminium cone as the P3D2-10? Yes — both use anodised aluminium cone and dustcap, the defining construction upgrade of the P3 series over the P1 and P2 Kevlar paper cones. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate M2WL-8 M2 Series 8 Inch 2-Way Wake Tower Speakers in White - Pair A pair of marine grade 8 inch 2-way wake tower speakers with Color Optix RGB LED lighting, 250W RMS handling, and a universal clamping system for bars from 1.5 to 3.0 inches in diameter. Loaded sealed enclosures in white with dual Deutsch/Amphenol 6-pin marine connectors, interchangeable grille options, and 360-degree rotating 3DIL rear logo. Sold as a pair. Backed by a 1 year warranty. Product Overview The Rockford Fosgate M2WL-8 is a pair of M2 series 8 inch 2-way loaded wake tower speaker enclosures in white, purpose-built for the marine environment. Each enclosure houses the M2-8 2-way full-range speaker and is constructed from high-density ASA material with IPX6 water intrusion rating and full Element Ready protection against dust, UV, temperature extremes, corrosion, and vibration. The included universal clamp system mounts to wake tower bars from 1.5 to 3.0 inches in diameter and offers 360 degrees of rotation, allowing the speaker to be aimed in any direction. Direct mounting is also supported for bars with that capability. Dual integrated Deutsch/Amphenol 6-pin connectors provide True Marine Ecosystem plug-and-play connectivity with flexible installation options. The ICC (Integrated Concealed Crossover) is hidden inside the basket for a cleaner look and easier installation. Color Optix RGB LED lighting is fully controllable via the PMX-RGB controller and RF Connect app (available on iOS and Android). The 3DIL (3D Illuminated Logo) technology allows the rear Rockford Fosgate emblem to rotate 365 degrees so it remains correctly oriented regardless of mounting angle. Both stainless steel and sport grilles are included, with additional grille options available separately for further customisation. The black version of these speakers is available as the M2WL-8B. Klippel Verified certification and VAST surround technology are applied throughout the M2 series. Features & Benefits Color Optix RGB LED Lighting - App Controlled: The Color Optix system delivers bright, wide-angle RGB illumination fully controllable via the PMX-RGB controller and RF Connect app on iOS and Android. Lighting colour, effects, and intensity can be customised to match your boat or personal style. 3DIL Technology - 365-Degree Rotating Rear Logo: The 3D Illuminated Logo (3DIL) rotates a full 365 degrees so the illuminated Rockford Fosgate rear emblem is always correctly oriented regardless of the angle at which the speaker is mounted to the tower. Universal Clamping System - 1.5 to 3.0 Inch Bars: The included universal clamps fit wake tower bars from 1.5 to 3.0 inches in diameter and offer full 360-degree rotation, allowing the speakers to be pointed in any direction for optimal audio coverage. Rubber inserts for both 1.5-2.5 inch and 2.5-3.0 inch bars are included. True Marine Ecosystem - Dual Deutsch/Amphenol 6-Pin Connectors: Dual integrated Deutsch and Amphenol 6-pin connectors provide industry-leading marine plug-and-play connectivity, enabling flexible installation and reliable waterproof signal and power connections throughout the system. VAST Surround Technology - Up to 25% More Cone Area: Rockford Fosgate's Vertical Attach Surround Technique attaches the surround vertically to the cone, increasing the effective radiating cone area by up to 25% and delivering more output from the same physical speaker size. ICC Crossover - Integrated and Concealed: The Integrated Concealed Crossover is hidden inside the basket, resulting in a cleaner external appearance and simplifying installation by eliminating the need for a separate crossover component. Multiple Grille Options Included: Both stainless steel and sport grilles are included in the box, with additional grille options available separately to match the look and style of any boat or powersports vehicle. Element Ready and IPX6 Rated: All components are protected against dust, UV radiation, temperature extremes, water, corrosion, and vibration. IPX6 rating confirms protection against powerful jets of water from any direction. Technical Specs Specification Detail SKU M2WL-8 Colour White Speaker Type 2-Way Loaded Enclosure Speaker Series M2-8 Speaker Size 8 inch Speaker Quantity 2 (sold as a pair) Nominal Impedance 4 Ohm Power Handling 250W RMS / 1000W Peak Frequency Response 35 Hz - 24 kHz Enclosure Design Sealed Enclosure Material High Density ASA Speaker Connector 6-Pin Deutsch/Amphenol LED Voltage Range 9-16 VDC LED Current Draw 0.25A LED Recommended Fuse 1A Clamp Bar Diameter 1.5 to 3.0 inches Clamp Rotation 360 Degrees Water Intrusion Rating IPX6 Lighting Control Color Optix via PMX-RGB + RF Connect App Logo Technology 3DIL (365-Degree Rotating Illuminated Logo) Crossover ICC (Integrated Concealed Crossover) Surround Technology VAST Certifications CE Compliant, Klippel Verified Dimensions 324.0 x 230.4 x 365.7mm Shipping Weight 11kg Warranty 1 Year Compatible With / Goes Well With The M2WL-8 suits wakeboard boats, ski boats, pontoon boats, and any marine or powersports craft fitted with wake tower bars from 1.5 to 3.0 inches in diameter. Direct mounting is also supported for compatible tower bars. The black version is available as the M2WL-8B for applications requiring a black finish. Goes Well With: PMX-RGB - Rockford Fosgate Color Optix RGB controller required to operate the full Color Optix lighting system and RF Connect app integration M5-800X4 - M5 series 800W 4-channel marine amplifier to power the M2WL-8 pair alongside additional marine speakers M5-1500X5 - M5 series 1500W 5-channel marine amplifier for full system builds including wake tower speakers and a marine subwoofer M210S4B / M212S4 - Rockford Fosgate M2 series marine subwoofers to complete the on-water audio system M2WL-8B - Black version of these speakers for colour-matched installations Frequently Asked Questions Does the Color Optix lighting require a separate controller? Yes. Color Optix RGB lighting requires the PMX-RGB controller and the RF Connect app (available on iOS and Android) to access full colour control, lighting effects, and brightness adjustment. The PMX-RGB controller is sold separately and is not included in the box. What wake tower bar sizes are compatible with the included clamps? The included universal clamps fit bars from 1.5 to 3.0 inches in diameter. Rubber inserts for 1.5-2.5 inch bars and 2.5-3.0 inch bars are both included in the box. The speakers can also be direct mounted to compatible tower bars that support that option. What is 3DIL technology and why does it matter? 3DIL (3D Illuminated Logo) allows the illuminated Rockford Fosgate rear emblem to rotate a full 365 degrees independently of the speaker enclosure. This means the logo remains correctly oriented and readable regardless of the angle the speaker is mounted at on the tower, maintaining a clean and professional appearance from any viewing position. What is the difference between the M2WL-8 and the M2WL-8B? The M2WL-8 and M2WL-8B are identical in specifications and features. The only difference is the enclosure colour - the M2WL-8 is white and the M2WL-8B is black. Choose based on the colour scheme of your boat or wake tower setup. Are additional grille styles available beyond what is included in the box? Yes. The box includes both stainless steel and sport grilles. Rockford Fosgate offers additional grille options separately to further personalise the look of the M2WL-8 to match the style of your vessel or powersports vehicle.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate M2WL-8HB M2 Series 8 Inch 2-Way Horn Loaded Wake Tower Speakers in Black - Pair A pair of marine grade 8 inch 2-way horn loaded wake tower speakers in black with Color Optix RGB LED lighting, 300W RMS handling, and a universal clamping system for bars from 1.5 to 3.0 inches in diameter. Loaded sealed enclosures featuring an integrated 1 inch high-efficiency horn tweeter for superior projection to skiers and wakeboarders, dual Deutsch/Amphenol 6-pin marine connectors in two locations, and 360-degree rotating 3DIL rear logo. Sold as a pair. Backed by a 2 year warranty. Product Overview The Rockford Fosgate M2WL-8HB is a pair of M2 series 8 inch 2-way horn loaded wake tower speaker enclosures in black, built on the same platform as the M2WL-8H but in a black finish. Each enclosure houses the M2-8HB driver featuring an integrated 1 inch (25mm) high-efficiency horn tweeter designed to project music further and with greater clarity toward the skier or wakeboarder at distance. Power handling is 300W RMS and 1200W peak, with a frequency response of 20Hz-25kHz. Each enclosure is constructed from 100% UV stable high-density ASA plastic with IPX6 water intrusion rating and full Element Ready protection against dust, UV radiation, temperature extremes, corrosion, and vibration. The included universal clamp system mounts to wake tower bars from 1.5 to 3.0 inches in diameter with 360 degrees of rotation for precise aiming. Direct mounting is also supported for compatible tower bars. Dual integrated Deutsch/Amphenol 6-pin connectors in two locations support both thru-clamp and direct-mount configurations. Deutsch DT connectors incorporate front and rear silicone seals against environmental ingress. The ICC (Integrated Concealed Crossover) is hidden inside the basket for a cleaner installation. Color Optix RGB LED lighting is fully controllable via the PMX-RGB controller and RF Connect app (available on iOS and Android, sold separately). The 3DIL (3D Illuminated Logo) technology allows the rear Rockford Fosgate medallion to rotate 360 degrees so it remains correctly oriented regardless of mounting angle. Both stainless steel and black sport grilles are included. The white version of these speakers is available as the M2WL-8H. For a standard (non-horn) black wake tower speaker, refer to the M2WL-8B. Klippel Verified certification and VAST surround technology are applied throughout. Features & Benefits Integrated 1 Inch Horn Tweeter - Superior Projection at Distance: The integrated 1 inch (25mm) high-efficiency horn tweeter projects high-frequency sound further and with greater directional accuracy toward the skier or wakeboarder than a conventional dome tweeter, delivering clear, far-reaching audio across the full 20Hz-25kHz frequency response. 300W RMS / 1200W Peak Power Handling: The M2-8HB driver handles 300W RMS and 1200W peak, providing ample headroom for high-volume outdoor use on the water in demanding listening environments. Color Optix RGB LED Lighting - App Controlled: The Color Optix system delivers bright, wide-angle RGB illumination across both the front speaker LEDs and the rear 3DIL medallion, controllable via the PMX-RGB controller and RF Connect app on iOS and Android. Colour, effects, and intensity are fully customisable to match any vessel or personal style. 3DIL Technology - 360-Degree Rotating Rear Logo: The 3D Illuminated Logo (3DIL) rotates a full 360 degrees so the illuminated Rockford Fosgate rear medallion is always correctly oriented regardless of mounting angle, maintaining a professional appearance from any viewing position. Universal Clamping System - 1.5 to 3.0 Inch Bars: The included universal clamps fit wake tower bars from 1.5 to 3.0 inches in diameter with full 360-degree rotation for precise speaker aiming. Rubber inserts for both 1.5-2.5 inch and 2.5-3.0 inch bars are included. Dual Deutsch/Amphenol connector locations support both thru-clamp and direct-mount installation methods. VAST Surround Technology - Up to 25% More Cone Area: Rockford Fosgate's Vertical Attach Surround Technique attaches the surround vertically to the cone, increasing the effective radiating cone area by up to 25% for more output from the same physical speaker size. ICC Crossover - Integrated and Concealed: The Integrated Concealed Crossover is hidden inside the basket, resulting in a cleaner external appearance and simplifying installation by eliminating a separate crossover component. 100% UV Stable ASA Construction with IPX6 Rating: The frame and grille are constructed from 100% UV stable ASA plastic. IPX6 water intrusion rating confirms protection against powerful jets of water from any direction. Gold-plated marine grade brass terminals and Deutsch DT connectors with front and rear silicone seals protect against environmental ingress throughout the service life of the speakers. Technical Specs Specification Detail SKU M2WL-8HB Colour Black Speaker Type 2-Way Horn Loaded Enclosure Speaker Series M2 (M2-8HB) Speaker Size 8 inch Tweeter 1 inch (25mm) Integrated High-Efficiency Horn Speaker Quantity 2 (sold as a pair) Nominal Impedance 4 Ohm Power Handling 300W RMS / 1200W Peak Frequency Response 20 Hz - 25 kHz Enclosure Design Sealed Enclosure Material High Density ASA (100% UV Stable) Speaker Connector 6-Pin Deutsch/Amphenol (2 locations) LED Voltage Range 9-16 VDC LED Current Draw 0.25A LED Recommended Fuse 1A Clamp Bar Diameter 1.5 to 3.0 inches Clamp Rotation 360 Degrees Water Intrusion Rating IPX6 Terminals Gold-Plated Marine Grade Brass Lighting Control Color Optix via PMX-RGB + RF Connect App Logo Technology 3DIL (360-Degree Rotating Illuminated Logo) Crossover ICC (Integrated Concealed Crossover) Surround Technology VAST Certifications CE Compliant, Klippel Verified Dimensions 324.0 x 230.4 x 365.7mm (12.75 x 9 x 14.4 inch) Shipping Weight 9.8kg Warranty 2 Years Compatible With / Goes Well With The M2WL-8HB suits wakeboard boats, ski boats, pontoon boats, and any marine or powersports craft fitted with wake tower bars from 1.5 to 3.0 inches in diameter. It is the recommended choice for black-themed builds where audio needs to project clearly to riders at tow sport distances. The white version is available as the M2WL-8H. For a standard (non-horn) black tower speaker, refer to the M2WL-8B. Goes Well With: PMX-RGB - Rockford Fosgate Color Optix RGB controller required to operate the full Color Optix lighting system and RF Connect app integration M5-800X4 - M5 series 800W 4-channel marine amplifier to power the M2WL-8HB pair alongside additional marine speakers M5-1500X5 - M5 series 1500W 5-channel marine amplifier for full system builds including wake tower speakers and a marine subwoofer M210S4B / M212S4 - Rockford Fosgate M2 series marine subwoofers to complete the on-water audio system M2WL-8H - White version of these speakers for colour-matched white installations M2WL-8B - Black non-horn version for applications where directional projection at distance is less critical Frequently Asked Questions What is the difference between the M2WL-8HB and the M2WL-8B? Both are black 8 inch M2 series wake tower speakers with Color Optix lighting, the same clamping system, and the same bar diameter compatibility. The M2WL-8HB is the horn-loaded version, featuring an integrated 1 inch high-efficiency horn tweeter that projects high-frequency sound further and with greater directional accuracy toward the skier or wakeboarder. It handles 300W RMS / 1200W peak versus 250W RMS / 1000W peak on the M2WL-8B. Choose the M2WL-8HB for tow sport applications where projection at distance is a priority; choose the M2WL-8B for general on-water listening where directional projection is less critical. What is the difference between the M2WL-8HB and the M2WL-8H? The M2WL-8HB and M2WL-8H are identical in specifications and features. The only difference is the enclosure colour - the M2WL-8HB is black with black sport grilles, and the M2WL-8H is white with white sport grilles. Choose based on the colour scheme of your boat or wake tower setup. Does the Color Optix lighting require a separate controller? Yes. Color Optix RGB lighting requires the PMX-RGB controller and the RF Connect app (available on iOS and Android) to access full colour control, lighting effects, and brightness adjustment for both the front speaker LEDs and the rear 3DIL medallion. The PMX-RGB controller is sold separately and is not included. The speakers can also operate without the controller at a fixed default colour setting straight out of the box. What wake tower bar sizes are compatible with the included clamps? The included universal clamps fit bars from 1.5 to 3.0 inches in diameter. Rubber inserts for 1.5-2.5 inch bars and 2.5-3.0 inch bars are both included in the box. The speakers can also be direct mounted to compatible tower bars, with Deutsch/Amphenol connector locations provided for both thru-clamp and direct-mount configurations. Are additional grille styles available beyond what is included in the box? Yes. The box includes both stainless steel and black sport grilles. Rockford Fosgate offers additional grille options separately to further personalise the look of the M2WL-8HB to match the style of your vessel or powersports vehicle.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

250 watts per channel. 500 watts bridged. Punch EQ2 tone control and real-time output monitoring. Product Overview The Rockford Fosgate P500X2 is a 2-channel Class A/B stereo amplifier from the Punch series, delivering 250W RMS per channel into 2-ohm loads or 150W per channel at 4 ohms. When bridged, it combines both channels into a single 500W RMS mono output at 4 ohms, making it a capable driver for a pair of 8-ohm SVC subwoofers in parallel, or a quad configuration of 2-ohm DVC subwoofers. Total rated output is 500W RMS, CEA-2006 verified. Where the P500X2 stands apart within the Punch 2-channel range is its Punch EQ2 tone control system a dual-band EQ offering up to +18dB of bass boost at 45Hz and up to +12dB of treble lift at 12kHz, with the active EQ function varying depending on the amplifier's LP/AP/HP crossover switch position. Combined with a tri-colour output clip LED that displays real-time THD levels, an independent input clip LED, and thermal protection monitoring, the P500X2 gives the installer and listener more visibility into amplifier performance than any other unit in the Punch stereo range. Wide input sensitivity (150mV–12V) supports a broad range of source units, and Captive C-Clamp connectors on both power and speaker terminals provide a secure, vibration-resistant connection. Key Specifications Channels: 2 Rated power @ 4 ohms: 150W RMS x 2 Rated power @ 2 ohms: 250W RMS x 2 Rated power bridged @ 4 ohms: 500W RMS x 1 Total rated power: 500W RMS (CEA-2006) Dynamic power @ 4 ohms: 223W x 2 (PowerCube) Dynamic power @ 2 ohms: 365W x 2 (PowerCube) Bridgeable: Yes — 500W x 1 @ 4 ohms Circuit topology: Class A/B Efficiency (average): 73% @ 4 ohms Frequency response: 20Hz – 20kHz (+/-1dB) Input sensitivity: 150mV – 12V THD+Noise: <1.0% @ 4 ohms / <1.0% @ 2 ohms Punch EQ2 Bass: 0dB to +18dB @ 45Hz Punch EQ2 Treble: 0dB to +12dB @ 12kHz Crossover: 12dB/octave Butterworth — LP / AP / HP switch Signal input: Hi/Low level, 1 x RCA pair Signal output: 1 x RCA pair (pass-through) Remote control: Optional PLC2 (not included — sold separately) Visual indicators: Power / Protect / Thermal LED, Input Clip LED, Output Clip LED (tri-colour THD) Power wire gauge: 4 AWG Power input connector: Captive C-Clamp Speaker wire gauge: 8 AWG – 18 AWG Speaker output connector: Captive C-Clamp Cooling: Convection Operating voltage: 9–16V DC Recommended fuse: 80A (not included) Average current draw: 40A @ 13.8V (music) Max current draw: 80A @ 13.8V (sinewave) Suggested alternator: 75A minimum Dimensions (H x W x D): 6.05 x 19.71 x 33.73 cm Shipping weight: 5.57 kg Compliance: CEA-2006 Features & Benefits 250W Per Channel @ 2Ω | 500W Bridged @ 4Ω — Full Flexibility — Run in stereo at 250W per channel for a pair of speakers, or bridge to a single 500W mono output for a subwoofer configuration. The P500X2 covers both use cases from one chassis — useful for systems that may evolve from a speaker-focused build to one incorporating a dedicated subwoofer without requiring a second amplifier purchase. Punch EQ2 — Dual-Band Bass and Treble Control — Unlike the single-band Punch EQ found on other amplifiers in the range, the Punch EQ2 includes both a bass control (0dB to +18dB @ 45Hz) and a treble control (0dB to +12dB @ 12kHz). The active EQ band changes depending on the crossover switch position — in Low-Pass mode the bass EQ is operative, in High-Pass mode the treble EQ is operative, and in All-Pass (bypass) mode both bands can be used simultaneously. This allows frequency-appropriate tuning regardless of how the amplifier is deployed in the system. Tri-Colour Output Clip LED — Real-Time THD Monitoring — The output clip LED displays three distinct states based on measured distortion at the output stage: blue indicates clean output below 0.5% THD, violet indicates approaching 1% THD, and red signals 10% or greater THD — a level that causes audible distortion and risks speaker damage. This real-time feedback allows gain calibration confirmation after installation and ongoing monitoring during use. It is one of the most practical diagnostic tools available on an amplifier at this price point. Independent Input Clip LED — A separate LED monitors the incoming signal for clipping before it enters the amplifier. Combined with the output clip LED, this allows the installer to distinguish between clipping at the source (head unit or preamp) and clipping generated within the amplifier itself — essential for accurate gain structure setup. C.L.E.A.N. Setup System — The on-board C.L.E.A.N. calibration system works alongside the clip LEDs to guide precise gain matching between the source unit and the P500X2. Together, these tools eliminate the guesswork that causes premature speaker failure from miscalibrated gain settings. Wide Input Sensitivity (150mV – 12V) — An unusually broad input sensitivity range accommodates everything from low-output factory head units to high-output aftermarket preamps without requiring external level adjustment. This extends compatibility across a wide range of source units in new and factory-retained head unit configurations. High-Level Input with Auto Turn-On — Accepts speaker-level signal from factory head units and powers on automatically when signal is detected — no remote turn-on wire required. The wide 150mV–12V sensitivity range further simplifies integration with both OEM and aftermarket systems. Optional PLC2 Remote Level Control — The P500X2 is wired and ready for the Rockford Fosgate PLC2 (sold separately), adding driver-accessible output adjustment and activating the input clip indicator for front-seat gain monitoring. Not included — sold separately. Captive C-Clamp Connectors — Power input and speaker output terminals use Captive C-Clamp connectors rather than standard screw terminals. The C-Clamp design applies distributed clamping pressure across a wider contact area, providing a more vibration-resistant and mechanically secure connection — particularly beneficial in vehicles subject to road vibration, off-road use, or high-power current demands. RCA Pass-Through Output — Signal chains cleanly to a second amplifier via the RCA pass-through — useful in systems running the P500X2 on speakers alongside a separate Punch mono amplifier handling subwoofer duty. LP / AP / HP Crossover Switch — The three-position crossover switch configures the P500X2 as a low-pass filtered amplifier (sub channel), all-pass (full-range), or high-pass filtered (speaker channel in a crossed-over system), each mode also governing which EQ band of the Punch EQ2 is active. Crossover frequency range is not specified in the provided data — confirm with Rockford Fosgate. Thermal LED + Full Protection — A dedicated thermal LED provides visual warning of elevated operating temperatures before the protection circuit activates. Over-current and short-circuit protection are active across both channels, and muted turn-on prevents power-up thumps that can stress tweeters. Technical Specs Specification Detail Channels 2 Rated power @ 4Ω 150W RMS x 2 Rated power @ 2Ω 250W RMS x 2 Rated power — bridged @ 4Ω 500W RMS x 1 Total rated power 500W RMS Dynamic power @ 4Ω 223W x 2 (PowerCube) Dynamic power @ 2Ω 365W x 2 (PowerCube) Bridgeable Yes Circuit topology Class A/B Efficiency (average) 73% @ 4Ω Frequency response 20Hz – 20kHz (+/-1dB) Input sensitivity 150mV – 12V THD+Noise <1.0% @ 4Ω / <1.0% @ 2Ω Punch EQ2 Bass 0dB to +18dB @ 45Hz Punch EQ2 Treble 0dB to +12dB @ 12kHz Crossover LP / AP / HP switch — 12dB/octave Butterworth Crossover frequency range Not specified Signal input Hi/Low level, 1 x RCA pair Signal output 1 x RCA pair (pass-through) Remote control Optional PLC2 (sold separately) Output clip LED Tri-colour: Blue (<0.5% THD) / Violet (1% THD) / Red (10%+ THD) Input clip LED Yes Thermal LED Yes Power / Protect LED Yes Power wire gauge 4 AWG Power input connector Captive C-Clamp Speaker wire gauge 8 AWG – 18 AWG Speaker output connector Captive C-Clamp Cooling Convection Operating voltage 9–16V DC Recommended fuse 80A (not included) Average current draw 40A @ 13.8V (music) Max current draw 80A @ 13.8V (sinewave) Suggested alternator 75A minimum Dimensions (H x W x D) 6.05 x 19.71 x 33.73 cm Shipping weight 5.57 kg Compliance CEA-2006 Compatible With / Goes Well With Stereo speaker mode: 4-ohm coaxial or component speakers — 150W RMS per channel 2-ohm coaxial or component speakers — 250W RMS per channel Component speaker sets with passive crossovers (crossovers not supplied) Factory and aftermarket head units (150mV–12V input sensitivity) Bridged mono mode (500W @ 4Ω): Pair of 8-ohm SVC subwoofers wired in parallel (combined 4Ω load — confirmed by manufacturer) Quad configuration of 2-ohm DVC subwoofers wired to a combined 4Ω load (confirmed by manufacturer — specific wiring required; professional installation strongly recommended) Goes well with: Rockford Fosgate Punch series speakers (matched to 150W or 250W per channel) Rockford Fosgate P300X1 or Punch mono amplifier (via RCA pass-through for a full two-amp system) Rockford Fosgate PLC2 Remote Punch Level Control (optional — sold separately) Aftermarket head units with RCA preamp outputs (150mV–12V sensitivity compatible) Frequently Asked Questions What subwoofer configurations can the P500X2 drive when bridged? Bridged at 4 ohms, the P500X2 produces 500W RMS. The manufacturer confirms two configurations: a pair of 8-ohm SVC subwoofers wired in parallel, or a quad of 2-ohm DVC subwoofers in a specific series/parallel arrangement — both presenting a 4Ω load. Do not bridge below 4 ohms. What is Punch EQ2 and how does it differ from standard Punch EQ? Punch EQ2 is a dual-band tone control offering both bass boost (up to +18dB @ 45Hz) and treble boost (up to +12dB @ 12kHz). The active band changes depending on the LP/AP/HP crossover switch position — bass EQ in Low-Pass mode, treble EQ in High-Pass mode, and both available in All-Pass mode. What does the tri-colour output clip LED indicate? The output clip LED changes colour based on measured THD at the amplifier's output: blue indicates clean output below 0.5% THD, violet signals approximately 1% THD, and red indicates 10% or greater THD — audible distortion that risks speaker damage. It allows real-time gain monitoring without test equipment. Is the Punch Level Control included with the P500X2? No. The PLC2 remote Punch Level Control is an optional accessory sold separately. The P500X2 is fully wired to accept it, and when connected the PLC2 adds driver-accessible output adjustment and activates the input clip indicator for front-seat monitoring. What does CEA-2006 compliance mean for the P500X2? CEA-2006 requires power ratings to be measured simultaneously across all channels under defined conditions. The 250W x 2 and 500W bridged figures are verified, real-world specifications — not single-channel burst or inflated peak ratings. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less