Victron Energy Phoenix Inverter 48/500 230V VE.Direct AU/NZ Inverters convert stored direct current(DC) power in your batteries into alternating power (AC) power, like the kind you get in your home, so you can run your electrical appliances wherever you are. There are two types of inverters pure sine wave and modified sine wave. Modified sine wave inverters are a more basic form of technology than pure sine wave inverters, they produce power which is perfectly adequate for powering simple electronics. Use modified sine wave inverters to provide power for your less sensitive appliances like phone chargers, heaters and air conditioners. Modified inverters are best suited for resistive loads that don't have a start-up surge. Pure sine wave inverters use sophisticated technology to protect even the most sensitive electronics. Pure sine wave inverters produce power that equals – or is better than – the power in your home. Appliances that may not function properly or be permanently damaged without pure, smooth power will be safe with pure sine inverters. Use these inverters for televisions, laptops, digital microwaves, fridges and other sensitive electronic equipment. Pure Sine inverters can power just about any AC appliance without risk of damage. VE.Direct Communication Port: The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook and other devices (VE.Direct Bluetooth Smart dongle needed) Fully Configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: Input and output voltage, % load and alarms. Proven Reliability: The full bridge plus toroidal transformer topology has proven reliable over many years. The inverters are short-circuit proof and protected against overheating, whether due to overload or high ambient temperature. High Start-up Power: They are needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO Mode: When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once on standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote On/Off: A remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector. LED Diagnosis: A red and a green LED indicate the inverter operation and status of the different protections. Automatic Transfer Switch - to transfer the load to another AC source: For our low-power inverters, the Filax Automatic Transfer Switch is recommended. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will operate without disruption. *Bluetooth dongle to be purchased separately* Victron Energy PIN481501300 Features: Pure Sinewave Inverter Optimised Efficiency SinusMax Engineering High Start-Up Power VE.Direct Communication Port Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Phoenix Power Inverter 24/500 230V VE.Direct: Take Control of your Charging Needs When on the Go Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. LED diagnosis Please see manual for a description. To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Fully Configurable: Low voltage alarm trip and reset levels Low voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 - 245V Frequency: 50Hz or 60Hz ECO mode on/off and ECO mode sense level Monitoring: In and output voltage and alarms Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

The Inverter Chargers From Victron Energy Have Been Designed to Be a True Worldwide Product Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

The Inverter Chargers From Victron Energy Have Been Designed to Be a True Worldwide Product SinusMax - Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimised efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top-quality product with compact dimensions, light in weight and capable of supplying power, problem-free, to any load. Extra start-up power A unique feature of the SinusMax technology is its very high start-up power. Conventional high-frequency technology does not offer such extreme performance. Phoenix inverters, however, are well suited to power up difficult loads such as refrigeration compressors, electric motors and similar appliances. Virtually unlimited power thanks to parallel 3-phase and split phase operation capability Up to 6 units of inverters can operate in parallel to achieve higher power output. Six 24/3000 units, for example, will provide 15 kW / 18 kVA output power. Operation in a 3-phase or split phase configuration is also possible. To transfer the load to another AC source: the automatic transfer switch If an automatic transfer switch is required we recommend using the MultiPlus inverter/charger instead. The switch is included in these products and the charger function of the MultiPlus can be disabled. Computers and other electronic equipment will continue to operate without disruption because the MultiPlus features a very short switchover time (less than 20 milliseconds). Computer interface All models have an RS-485 port. All you need to connect to your PC is our MK3-USB VE. Bus to USB interface (see under accessories). Together with our VEConfigure software, which can be downloaded free of charge from our website, all parameters of the inverters can be customised. This includes output voltage and frequency, over and under voltage settings and programming the relay. This relay can for example be used to signal several alarm conditions or to start a generator. The inverters can also be connected to VENe Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 100A (3) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024100002 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 20 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 3 x 80 A Charge current starter batt. (A): n.a Charge algorithm: 7 stage adaptive Battery capacity (Ah): 500-1000 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 100A (1+1) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024100000 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 20 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 100 A Charge current starter batt. (A): 4 Charge algorithm: 7 stage adaptive Battery capacity (Ah): 500-1000 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 80A (3) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024080002 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 16 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 3 x 80 A Charge current starter batt. (A): n. a. Charge algorithm: 7 stage adaptive Battery capacity (Ah): 400-800 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-i 24V 80A (1+1) Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide Product A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i (1+1): two outputs to charge 2 battery banks The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Skylla-i (3): three full current outputs to charge 3 battery banks The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Victron Energy SKI024080000 Specifications: Skylla-i Input voltage (VAC): 230 V Input voltage range (VAC): 185-265 V Input voltage range (VDC): 180-350 V Maximum AC input current @ 180 VAC: 16 A Frequency (Hz): 45-65 Hz Power factor: 0,98 Charge voltage 'absorption' (VDC): 28,8 V Charge voltage 'float' (VDC): 27,6 V Charge voltage ‚Äòstorage' (VDC): 26,4 V Charge current (A): 80 A Charge current starter batt. (A): 4 A Charge algorithm: 7 stage adaptive Battery capacity (Ah): 400-800 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay: DPST, AC rating: 240VAC/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes Protection Battery: reverse polarity (fuse), Output short circuit, Over temperature Operating temp. range -20 to 60¬∞C (Full output current up to 40¬∞C) Humidity (non-condensing) max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: M8 bolts 230 VAC-connection: screw-clamp 10mm¬≤ (AWG 7) Protection category: IP 21 Weight kg (lbs): 7 kg (16 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Sun Inverter 24/250-10 IEC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Sun Inverter 12/250-15 IEC Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy SmartShunt 2000A / 50mV - Bluetooth Battery Shunt: Powerful Battery Monitor with Bluetooth on Board for Monitoring on Your Mobile Phone, Tablet or Computer Smart Battery Shunt 2000A/50MV The SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. The SmartShunt is available in 2000A. The SmartShunt connects via Bluetooth to the VictronConnect App. The VictronConnect App is used to read out all monitored battery parameters and is also used to make or change settings. Alternatively, the SmartShunt can connect to a GX device, like the ColorControl GX or the Cerbo GX. The SmartShunt has an auxiliary input that can be used to monitor the voltage of a second battery or to monitor the midpoint of a battery bank. The auxiliary input can also be used for battery temperature monitoring together with the optional Temperature sensor for BMV. Differences Compared To BMV712 Battery Monitor: No Programmable Visual & Audible Alarm No Programmable Relay Victron Energy SHU050220050 Specifications: Supply Voltage Range: 6,5 - 70 VDC Current Draw: < 1mA Input Voltage Range, Auxiliary Battery: 6,5 - 70 VDC Battery Capacity (Ah): 1 - 9999 Ah Operating Temperature Range: -40 +50¬∞C (-40 - 120¬∞F) Measures Voltage of Second Battery, Or Temperature, or Midpoint: Yes Temperature Measurement Range: -20 +50¬∞C VE. Direct Communication Port: Yes Current: ¬± 0,1A Voltage: ¬± 0,01V Amp Hours: ¬± 0,1 Ah State of Charge (0 – 100%): ¬± 0,1% Time to Go: ¬± 1 min Temperature: (0 - 50¬∞C or 30 - 120¬∞F) ¬± 1¬∞C/¬∞F Accuracy of Current Measurement: ¬± 0,4% Offset Less Than: 20 / 40 / 80 mA Accuracy of Voltage Measurement: ¬± 0,3% Dimensions (H X W X D): 500A: 46 x 120 x 54 mm Protection Category: IP21 Safety: EN 60335-1 Emission / Immunity: EN-IEC 61000-6-1 EN-IEC 61000-6-2 EN-IEC 61000-6-3 Automotive: EN 50498 Cables (Included): Two Cables with Fuse, for ‚Äò+' Connection & Starter Battery or Midpoint Connection Temperature Sensor: Optional (ASS000100000) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less