Victron Energy Smart BMS 12/200: The Smart BMS 12/200 Is An All-in-one Battery Management System For Victron Lithium-iron-phosphate (Lifepo4) Smart BatteriesIt has been specifically designed for 12V systems with a 12V alternator such as in vehicles and boats. It combines a Current Limiter, Battery Combiner, and Battery Protector in a robust and compact solution and lets you safely connect any size 12V alternator (and starter battery), loads, and chargers to Smart Lithium batteries.The Smart BMS 12/200 monitors and protects each battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources, or DC loads in case of low battery cell voltage, high battery cell voltage, or over temperature. The dedicated alternator connection provides current limiting and one-way traffic from the alternator into the battery, so any size alternator (and starter battery) can be safely connected to the Smart Lithium battery (or battery bank) and the starter battery is protected from excessive discharge. The BMS is equipped with Bluetooth for monitoring and configuration, a remote on/off connector, to turn the BMS (and the system) off via a remote switch, and a pre-alarm contact, to give a warning signal before the BMS will disconnect the batteries from the system.Battery Management System:The BMS connects to 12.8V Victron LiFePO4 (LFP) batteries. Up to 5 batteries may be connected in parallel. Can be used as a system on/off switch.Alternator and Battery Protection:The input current is electronically limited to approximately 90% of the fuse rating. A 100A fuse, for example, will therefore limit the input current to approximately 90A.Choosing the right fuse will: Protect the LFP battery against excessive charge current (important in the case of a low-capacity LFP battery). Protect the alternator against overload in case of a high-capacity LFP battery bank (most 12V alternators will overheat and fail if running at maximum output for more than 5 minutes). Starter battery Protection:This function is similar to that of a Cyrix Battery Combiner or Argo FET Battery Isolator. Current can flow to the LFP battery only if the input voltage (= voltage on the starter battery) exceeds 13V. Current cannot flow back from the LFP battery to the starter battery, thus preventing eventual damage to the LFP battery due to excessive discharge.Li-ion Battery Protection:Excessive input voltage and transients are regulated down to a safe level. The Smart BMS CL will stop charging in case the cell is over voltage or temperature. It has three outputs, similar to the miniBMS:Load Disconnect Output:The Load output is normally high and becomes free-floating in case of an imminent cell under voltage (default 2.8V/cell, adjustable on the battery between 2.6V and 2.8V per cell). Maximum current: 10mA. The Load output can be used to control the remote on/off input of a Battery Protect, inverter, DC-DC converter, or other loads.Pre-Alarm Output:The pre-alarm output can be used as a warning when the battery voltage is low and it will trip shortly before the Load Disconnect output is disabled due to cell under voltage. The pre-alarm output may be used to drive a relay, LED, or Buzzer. It can be configured as a continuous or intermittent signal.The pre-alarm output is normally free floating and becomes high in case of an imminent cell under voltage (default 3.1V/cell, adjustable on the battery between 2.85V and 3.15V per cell). Maximum current: 1A (not short circuit protected) The minimum delay between pre-alarm and load disconnect is 30 seconds.Charge Disconnect Output:The Charger output is normally high and becomes free-floating in case of an imminent cell over voltage or temperature. Maximum current: 10mA.The Charger output is not suitable to power an inductive load such as a relay coil. The Charger output can be used to control: The remote on/off of a charger, a Cyrix-Li-Charge relay, and a Cyrix-Li-ct Battery Combiner.(Note: In some cases, an interface cable will be needed, please see the manual.)Remote On/Off Input:The remote on/off input controls the charging via the alternator. When off, charging via the alternator is disabled, while the BMS functionality will remain active allowing any loads and chargers to continue working regardless of the state of the remote input.When the “system on/off switch” is enabled via VictronConnect, the BMS functionality will also be disabled. It consists of two terminals: Remote L and Remote H. A remote on-off switch or relay contact can be connected between H and L. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery minus.Ignition Proof:No relays but MOSFET switches, and therefore no sparks.Victron Energy BMS210055000 Features: Battery Management System Suits Victron Smart LiFePO4 Batteries Charge Disconnect Output Connect up to 5 Batteries 5 Year Warranty Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Reliable Workshop 30A Battery Charger Perfect for Large 12V Vehicles and Equipment Such as Trucks, Large Boats, Tractors, Agricultural Equipment and RVs Integrated 15A power supply allows the option of charging and powering equipment. Powerful 30A Battery Charger suitable for larger 12V equipment and vehicles. The 30 amp automatic battery charger is an efficient, water-resistant 8 stage charger, designed to charge most 12 volt GEL, AGM, Lead Acid and Calcium batteries. With a heavy duty design, it is suitable for 40-550Ah and 650Ah for maintenance (800 to 1,000CCA) making it ideal for workshops, garages and farm use. The fully automatic computer system includes an easy to read and comprehensive LED display and utilises pulse mode technology to reduce oxidation, maintain electrolyte consistency and combat stratification to provide longer battery life. Features: Input Voltage: 240VAC / 50HZ Type: 8 Stage Pulse Approval: CE, EMC, SAA and C-TICK Safety Protection: Over charging, reversing polarity (flashing LED), Short circuit and over temperature Minimum Start Voltage: ≤0 Volts Operating Temperature: -15°C – +50°C Display: Lights show stage of charge Ideally Suited Battery Ratings: 40-550Ah, 800-1,000CCA Specifications: Unit of Measure: Each Description: Battery Charger 30A Power Rating(Amp): 30 Voltage: 12 Charger/Analyser Type: Charger Charger Type: 8 Stage Ideal Battery Types: Gel, Calcium, AGM and Lead Acid Input Voltage: 240 VAC Legendary Products & Support From Authorized Dealers When you choose Thunder, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Thunder dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Thunder's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Thunder dealer today!

Read more less

Victron Energy Skylla-IP65 24/35(3) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located in the world.Victron Energy SKY024035100 Features: Skylla-IP65 (3): three full current outputs to charge 3 battery banks. The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full-rated output current IP65 Rating Protection With a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation Several chargers can be connected in parallel and synchronised with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 24/35(1+1) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located.Victron Energy SKY024035000 Features: Skylla-IP65 (1+1): two outputs to charge 2 battery banks. The Skylla-IP65 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A trickle charge and with a slightly lower output voltage, is intended to top up a starter battery. IP65 Rating Protection. With a steel epoxy powder-coated case the Skylla is built to withstand the rigours of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display.For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronized Parallel Operation. Several chargers can be connected in parallel and synchronized with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use. The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready. Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life. The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000). To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla 24/30(3) 120-240V Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide ProductSkylla-IP44 (1+1): two outputs to charge 2 battery banksThe Skylla-IP44 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.Skylla-IP44 (3): three full current outputs to charge 3 battery banksThe Skylla-IP44 (3) features 3 isolated outputs. All outputs can supply the full rated output current.IP44 protectionSteel epoxy powder coated case and splash proof. Withstands the rigors of an adverse environment: heat, humidity and salt air.Circuit boards are protected with an acrylic coating for maximum corrosion resistance.Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.LCD displayFor status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use.CAN bus interface (NMEA2000)To connect to a CAN bus network, to a Skylla-i Control panel or to the Color Control digital display.Synchronised parallel operationSeveral chargers can be connected in parallel and synchronised with help of the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables.The right amount of charge for a lead-acid battery: variable absorption timeWhen only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.Preventing damage due to excessive gassing: the BatterySafe modeIf, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP44 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging when the battery is not in use: the Storage modeThe Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (26,4V for 24V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.To increase battery life: temperature compensationEvery Skylla-IP44 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.Battery voltage senseIn order to compensate for voltage loss due to cable resistance, the Skylla-IP44 is provided with a voltage sense facility so that the battery always receives the correct charge voltage.Use as a power supplyAs a result of the excellent control circuit, the Skylla-IP44 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available.Li-Ion (LiFePO4) readySimple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger.Victron Energy SKY024030100 Specifications:Skylla-IP44 Input voltage (VAC): 120/230 V Input voltage range (VAC): 90-265 V Maximum AC input current @ 100 VAC: 10 A Frequency: 45-65 Hz Power factor: 0,98 Charge voltage 'absorption': 28,8 V Charge voltage 'float': 27,6 V Charge voltage ‘storage’: 26,4 V Charge current: 3 x 30 A Charge current starter batt. (A): n.a Charge algorithm: 7 stage adaptive Battery capacity: 150-300 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, not isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay DPST AC rating: 240VAC/4A DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes (internal air circulation) Protection: Battery reverse polarity (fuse) Output short circuit Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Humidity (non-condensing): max 95% Enclosure: Material & Colour: steel (blue RAL 5012) Battery-connection: M6 bolts 230 VAC-connection: screw-clamp 6mm² (AWG 10) Protection category IP44 Weight: 6kg (14 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla 24/30(1+1) 120-240V Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide ProductSkylla-IP44 (1+1): two outputs to charge 2 battery banksThe Skylla-IP44 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.Skylla-IP44 (3): three full current outputs to charge 3 battery banksThe Skylla-IP44 (3) features 3 isolated outputs. All outputs can supply the full rated output current.IP44 protectionSteel epoxy powder coated case and splash proof. Withstands the rigors of an adverse environment: heat, humidity and salt air.Circuit boards are protected with an acrylic coating for maximum corrosion resistance.Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.LCD displayFor status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use.CAN bus interface (NMEA2000)To connect to a CAN bus network, to a Skylla-i Control panel or to the Color Control digital display.Synchronised parallel operationSeveral chargers can be connected in parallel and synchronised with help of the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables.The right amount of charge for a lead-acid battery: variable absorption timeWhen only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.Preventing damage due to excessive gassing: the BatterySafe modeIf, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP44 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging when the battery is not in use: the Storage modeThe Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (26,4V for 24V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.To increase battery life: temperature compensationEvery Skylla-IP44 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.Battery voltage senseIn order to compensate for voltage loss due to cable resistance, the Skylla-IP44 is provided with a voltage sense facility so that the battery always receives the correct charge voltage.Use as a power supplyAs a result of the excellent control circuit, the Skylla-IP44 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available.Li-Ion (LiFePO4) readySimple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger.Victron Energy SKY024030000 Specifications:Skylla-IP44 Input voltage (VAC): 120/230 V Input voltage range (VAC): 90-265 V Maximum AC input current @ 100 VAC: 10 A Frequency: 45-65 Hz Power factor: 0,98 Charge voltage 'absorption': 28,8 V Charge voltage 'float': 27,6 V Charge voltage ‘storage’: 26,4 V Charge current: 30 A Charge current starter batt. (A): 3 A Charge algorithm: 7 stage adaptive Battery capacity: 150-300 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, not isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay DPST AC rating: 240VAC/4A DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes (internal air circulation) Protection: Battery reverse polarity (fuse) Output short circuit Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Humidity (non-condensing): max 95% Enclosure: Material & Colour: steel (blue RAL 5012) Battery-connection: M6 bolts 230 VAC-connection: screw-clamp 6mm² (AWG 10) Protection category IP44 Weight: 6kg (14 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 12/70(3) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge AlgorithmSuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located.Victron Energy SKY012070100 Features: Skylla-IP65 (3): three full current outputs to charge 3 battery banks. The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full-rated output current IP65 Rating Protection With a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions. LCD Display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation Several chargers can be connected in parallel and synchronised with the help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, a Skylla-i Control panel, or the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-IP65 12/70(1+1) 120-240V: A Powerful, Waterproof, And Intelligent Battery Charger With A 7 Stage Adaptive Charge Algorithmsuitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm and a wide 90VAC to 265AC input voltage range for worldwide use no matter where you are located in the world.Skylla-IP65 (1+1): two outputs to charge 2 battery banksThe Skylla-IP65 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A trickle charge and with a slightly lower output voltage, is intended to top up a starter battery.IP65 Rating ProtectionWith a steel epoxy powder-coated case the Skylla is built to withstand the rigors of adverse environments such as heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits if needed by automatic reduction of output current under extreme environmental conditions.Victron Energy SKY012070000 Features: LCD Display: For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. Synchronised Parallel Operation: Several chargers can be connected in parallel and synchronised with help of the CAN-bus interface. This is achieved by simply connecting the chargers with RJ45 UTP cables. Variable Absorption - the right amount of charge for a lead-acid battery: When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. BatterySafe mode - Preventing damage due to excessive gassing If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Storage mode - Less maintenance and aging when the battery is not in use The Storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector Opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN-bus port. Temperature Compensation - Increase battery life The Skylla-IP65 comes with a battery temperature sensor. When connected, the charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel, or to the Color Control digital display. Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla 12/60(3) 120-240V Battery Charger: The Skylla-i Battery Charger From Victron Energy Have Been Designed to Be a True World-wide ProductSkylla-IP44 (1+1): two outputs to charge 2 battery banksThe Skylla-IP44 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.Skylla-IP44 (3): three full current outputs to charge 3 battery banksThe Skylla-IP44 (3) features 3 isolated outputs. All outputs can supply the full rated output current.IP44 protectionSteel epoxy powder coated case and splash proof. Withstands the rigors of an adverse environment: heat, humidity and salt air.Circuit boards are protected with an acrylic coating for maximum corrosion resistance.Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.LCD displayFor status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use.CAN bus interface (NMEA2000)To connect to a CAN bus network, to a Skylla-i Control panel or to the Color Control digital display.Synchronised parallel operationSeveral chargers can be connected in parallel and synchronised with help of the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables.The right amount of charge for a lead-acid battery: variable absorption timeWhen only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.Preventing damage due to excessive gassing: the BatterySafe modeIf, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP44 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging when the battery is not in use: the Storage modeThe Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (26,4V for 24V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.To increase battery life: temperature compensationEvery Skylla-IP44 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.Battery voltage senseIn order to compensate for voltage loss due to cable resistance, the Skylla-IP44 is provided with a voltage sense facility so that the battery always receives the correct charge voltage.Use as a power supplyAs a result of the excellent control circuit, the Skylla-IP44 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available.Li-Ion (LiFePO4) readySimple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger.Victron Energy SKY012060100 Specifications:Skylla-IP44 Input voltage (VAC): 120/230 V Input voltage range (VAC): 90-265 V Maximum AC input current @ 100 VAC: 10 A Frequency: 45-65 Hz Power factor: 0,98 Charge voltage 'absorption': 14,4 V Charge voltage 'float': 13,8 V Charge voltage ‘storage’: 13,2 V Charge current: 3 x 60A Charge current starter batt. (A): n.a Charge algorithm: 7 stage adaptive Battery capacity: 300-600 Ah Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control Temperature sensor: Yes Can be used as power supply: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) CAN bus communication port (VE.Can): Two RJ45 connectors, NMEA2000 protocol, not isolated Synchronised parallel operation: Yes, with VE.Can Alarm relay DPST AC rating: 240VAC/4A DC rating: 4A up to 35VDC, 1A up to 60VDC Forced cooling: Yes (internal air circulation) Protection: Battery reverse polarity (fuse) Output short circuit Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Humidity (non-condensing): max 95% Enclosure: Material & Colour: steel (blue RAL 5012) Battery-connection: M6 bolts 230 VAC-connection: screw-clamp 6mm² (AWG 10) Protection category IP44 Weight: 6kg (14 lbs) Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy Skylla-TG 24/50 GMDSS 120-240V Battery Charger: The Skylla-TG Battery Charger From Victron Energy Have Been Designed to Be a True World-wide ProductGMDSSThe Global Maritime Distress & Safety System (GMDSS) was developed by the International Maritime Organisation (IMO) to improve maritime distress and safety communications.Power supplyThe Skylla TG has proven itself to be an excellent battery charger and power supply for GMDSS applications.However, when using a standard Skylla Charger, additional equipment is needed to perform the monitoring and alarm functions required for GMDSS.Installation made easy: the Skylla GMDSSThe Victron Skylla GMDSS Charger has been designed to provide all required monitoring and alarm data. Both the battery and the GMDSS system are connected directly to the charger. Data and alarms are displayed on a digital panel (VE.Net GMDSS panel, to be ordered separately). A standard eight wire UTP-cable connects the charger to the panel.No adjustments neededThe whole system is ‘click and go’: the panels are pre-programmed for GMDSS functionality. A simple, intuitive menu allows changing of settings if required.Battery time to goThe Skylla GMDSS charger has a built-in battery controller. The capacity of the battery is fully monitored so the panel can even indicate the ’time to go’ in case of a power supply black out.Perfect charger for any type of batteryCharge voltage can be precisely adjusted to suit any VRLA or flooded battery system.Victron Energy SDTG2400504 Specifications:Skylla-TG Input voltage (V AC): 230 Input voltage range (V AC): 90 - 265 Frequency (Hz): 45-65 Power factor: 1 Charge voltage 'absorption' (V DC): 28,5 Charge voltage 'float' (V DC): 26,5 Charge current (A): 50 Charge characteristic: IUoUo (three step) Temperature sensor: Yes Can be used as power supply: Yes Forced cooling: Yes Protection: a, b, c, d Operating temp. range: -40 to +50°C (-40 - 122°F) Humidity (non-condensing): max 95% Enclosure: Material & Colour: aluminium (blue RAL 5012) Battery-connection: Two 1,5 m cables GMDSS connection: One 1,5 m cable (+ to be taken directly from the battery) 230 V AC-connection: Three wire 2,5 mm² (AWG 6) cable. Length: 2 m Protection category: IP 21 Weight kg (lbs): 6 (13) Dimensions hxwxd in mm: 485x250x147 Accessories: VE.Net GMDSS panel: To be ordered separately UTP-cable: To be ordered separately Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less

Victron Energy 120W IP67 24/12-10 Orion DC-DC Converter: The DC-DC Converter From Victron Energy Have Been Designed to Be a True World-wide ProductCompletely encapsulated: waterproof, shockproof and ignition protectedWater, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.Extra-long input and output cablesThanks to the cables of 1.8 meters in length, intermediate cable interconnections to increase length even more will in most cases not be needed. This is an important reliability increasing feature in an area were IP67 protection grade is needed.Wide input voltage rangeWith 15 to 40 Volts input range, a stable output is ensured during surges or sags due to other equipment connected to same battery.Protected against overheatingIt can be used in a hot environment such as a machine room.Victron Energy ORI241210060 Specifications:Orion IP67 Input voltage range: 15-40VDC Under voltage shutdown: 13V Under voltage restart: 14V No load current at 24V: 20mA DC output voltage: 12V +/- 3% Maximum continuous output current: 10A Efficiency: 93% Ripple & Noise: 75mV pp Operating temperature range (derate 3% per °C above 40°C): -20 to +70°C (full rated output up to 40°C) Overload protection: Hiccup mode, recovers automatically after fault condition is removed Short circuit proof: Yes Protection against reverse polarity connection: With external fuse or circuit breaker (not included) Enclosure Material & Colour: Aluminium (blue RAL 5012) Protection category: IP67 DC connection: Two input and two output cables, length 1,8m Cable cross section, input: 1,5mm² (15 AWG) Cable cross section, output: 1,5mm² (15 AWG) Weight (kg): 300 g Dimensions (h x w x d in mm): 74 x 74 x 32 Legendary Products & Support From Authorized Dealers When you choose Victron Energy, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Victron Energy dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Victron Energy's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Victron Energy dealer today!

Read more less