OEX ACX5607 Engel Style DC Power Socket 15A at 12V and 7.5A at 24V 29mm Panel Mount Blade Terminals The OEX ACX5607 is an Engel-style DC power socket rated at 15A at 12V (7.5A at 24V), designed for dash or panel mounting via a 29mm round hole. The Engel socket format is the standard DC power connector used on Engel-brand portable fridges and many other Australian-market 12V and 24V accessories, making this socket a common requirement for 4WD, caravan and marine installations where Engel-compatible accessories need a dedicated panel-mount power point. Blade terminals on the rear for direct wiring to the vehicle supply. Plastic housing. Not interchangeable with cigarette lighter or Anderson plug accessories. Covered by a one year warranty. Product overview The Engel socket has a different connector shape and pin configuration from a standard cigarette lighter socket and the two are not interchangeable. If an accessory uses an Engel-style plug most commonly Engel portable fridges and compatible 12V accessories in the Australian market this is the correct panel-mount socket counterpart. For accessories using a cigarette lighter plug, a standard 12V accessory socket is required instead. The socket installs through a 29mm round hole in a dash, console or panel, with blade terminals on the rear for direct wiring to the 12V or 24V vehicle supply. At 15A at 12V it handles portable fridges, compressors and other high-draw 12V accessories. The 7.5A rating at 24V reflects the same watt-limited capacity across both voltages confirm the accessory's current draw does not exceed the rating for the voltage being used. Features and benefits Engel style socket format: Compatible with Engel-brand fridges and other accessories using the Engel DC connector. Not interchangeable with cigarette lighter or Anderson plug accessories. 15A at 12V and 7.5A at 24V: Sufficient for portable fridges, compressors and other high-draw 12V and 24V accessories. 29mm panel mount: Installs through a 29mm round panel hole for a clean, integrated appearance in dash, console and panel installations. Blade terminals: Direct wiring to the vehicle supply without additional connectors. 12V and 24V compatible: Suits both passenger vehicle and commercial vehicle systems. Plastic housing: Lightweight and corrosion-resistant. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX5607 Brand OEX Type Engel Style DC Socket Current Rating 15A at 12V, 7.5A at 24V Voltage 12V and 24V Termination Blade terminals Body Material Plastic Mount Type Dash or panel mount Mounting Hole 29mm Pack Quantity 1 Warranty One year Sold As Single unit Frequently asked questions What is an Engel-style socket? The Engel socket is a DC power connector format used as the standard power input on Engel-brand portable fridges and many other Australian-market 12V accessories. It has a different shape and pin configuration from a cigarette lighter socket and is not interchangeable with cigarette lighter plugs or Anderson connectors. If an accessory has an Engel-style plug, this is the correct panel-mount counterpart. What is the current rating for 12V and 24V use? The ACX5607 is rated at 15A at 12V and 7.5A at 24V. The derating at 24V reflects the same watt-limited capacity across both voltages. Ensure the accessory's current draw does not exceed these limits for the voltage being used. What size hole does this socket require? The socket requires a 29mm round mounting hole in the panel or dash. Confirm the hole diameter before drilling as this is a specific size. Is this socket the same as a cigarette lighter socket? No. The Engel socket has a different connector shape and pin configuration from a standard cigarette lighter socket. The two are not interchangeable. For accessories using a cigarette lighter plug, a standard 12V accessory socket is required instead. Does this socket come with a matching plug? The ACX5607 is the socket (panel-mount side) only. The matching Engel-style plug is typically supplied with Engel fridges and accessories. If a replacement Engel-style plug is required, check the OEX accessories range. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX5585 Prospector 12 LED Flood Beam Work Light 12x7W 10920 Raw Lumens 8200 Effective Lumens IP68 and IP69K Aluminium 12V and 24V The OEX ACX5585 Prospector is the top-tier configuration in the Prospector work light range, delivering 10920 raw lumens and 8200 effective lumens from twelve 7W LEDs in a flood beam pattern. IP68 and IP69K sealed against continuous submersion and high-pressure, high-temperature wash-down. Aluminium body, polycarbonate lens, DTP04-2P Deutsch-style connector and multiple bolt mounting options. CISPR 25 Class 3 EMC compliant. Colour-coded backplate identifies the flood beam pattern. 12V and 24V compatible. 3-year warranty. Product overview The ACX5585 is the maximum output and highest-specification Prospector in the flood beam line-up. The twelve 7W LEDs deliver 10920 raw lumens and 8200 effective lumens across a wide-angle flood pattern, suited to applications where broad area coverage is the priority work site lighting, reversing and manoeuvring lights on large equipment, cargo area illumination on trucks, agricultural machinery field lighting and marine deck lighting. Where the ACX5580 (5 LED, spot) and ACX5581 (5 LED, flood) and ACX5583 (9 LED, flood) offer compact, lower-power options for secondary and supplemental applications, the ACX5585 is built for primary high-output roles in the most demanding environments. The IP68 and IP69K dual rating sealed against continuous submersion and high-pressure, high-temperature wash-down makes it suited to mining, agricultural and commercial wash-down environments where the lower Prospector models may not be appropriate. The aluminium body provides robust heat dissipation for sustained high-output operation. The DTP04-2P Deutsch-style connector provides a positive-locking, vibration-resistant sealed electrical connection. At 7A draw at 12V, a 10A fuse and appropriately rated cable are recommended as a minimum. Features and benefits 12x7W LEDs, 10920 raw lumens, 8200 effective lumens: Maximum output in the Prospector range. Flood beam pattern for broad wide-angle area illumination. Flood beam pattern: Wide-angle illumination suited to work site lighting, reversing and manoeuvring, cargo area illumination, agricultural field lighting and marine deck coverage. IP68 and IP69K: Sealed against continuous submersion (IP68) and high-pressure, high-temperature wash-down (IP69K). Suited to mining, agricultural and commercial vehicle wash-down environments. Aluminium body: Robust, heat-dissipating housing for sustained high-output operation in demanding environments. Polycarbonate lens: Impact-resistant and UV-stable. 12V and 24V compatible: Suits passenger vehicles, 4WDs, trucks and plant equipment. DTP04-2P Deutsch-style connector: Weatherproof, positive-locking, vibration-resistant sealed electrical connection. Multiple bolt mounting: Flexible installation for machinery frames, bull bars, roof racks and custom mounts. CISPR 25 Class 3 EMC compliant: Meets electromagnetic compatibility standards for vehicle applications. Colour-coded backplate: Identifies the flood beam pattern within the Prospector range. 3-year warranty: Extended warranty reflecting the quality and durability of this Prospector model. Technical specs Specification Detail SKU ACX5585 Brand OEX Series Prospector Type LED Work Light LED Count 12 LED Power 7W per LED Beam Pattern Flood Raw Lumens 10920 Effective Lumens 8200 Voltage 12V and 24V Current Draw 7A at 12V Body Material Aluminium Lens Material Polycarbonate IP Rating IP68 and IP69K Connector DTP04-2P (Deutsch-style) Mount Multiple bolt Dimensions 157mm x 139mm x 85mm EMC Compliance CISPR 25 Class 3 Warranty 3 years Sold As Single unit Frequently asked questions What is a flood beam pattern suited to? A flood beam spreads light across a wide horizontal and vertical angle, providing broad area illumination at shorter to medium range. It is suited to reversing lights on large vehicles, machinery work lighting, cargo area illumination and site lighting where wide zone coverage matters more than long-range projection. For long-range focused illumination, the spot beam ACX5580 or ACX5582 is the appropriate choice. How does the ACX5585 compare to the 5 LED ACX5581 and 9 LED ACX5583? The ACX5581 (5 LED flood) delivers 4500+ lumens at 35W and suits supplemental and secondary work light positions. The ACX5583 (9 LED flood) delivers 8100+ lumens at 63W and suits primary work lighting in most applications. The ACX5585 (12 LED flood) delivers 8200 effective lumens with IP68/IP69K, an aluminium body and Deutsch-style connector the top-specification option for the most demanding environments. What does IP68/IP69K mean for this light? IP68 confirms the light is sealed against continuous submersion in water under pressure. IP69K confirms it withstands high-pressure, high-temperature water jets at close range, as used in agricultural and commercial vehicle wash-down procedures. Together these ratings make the ACX5585 suited to the most demanding wet and dirty working environments. What is the DTP04-2P connector? DTP04-2P is a Deutsch-style 2-pin connector rated for high-current and harsh-environment applications. It provides a positive-locking, sealed connection that resists vibration and moisture ingress. If the installation does not use a matching Deutsch connector, a pigtail adaptor or direct wiring modification may be required. What current does this light draw at 12V? The ACX5585 draws 7A at 12V. Ensure wiring, fusing and circuit capacity can handle this sustained current draw a 10A fuse and appropriately rated cable are recommended as a minimum for this installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3692BL 12V 5A IP65 Illuminated Latching Push Button Switch Blue LED Chrome Housing NO and NC Terminals 19mm Mount The OEX ACX3692BL is a 12V, 5A illuminated latching push button switch in an SPST On/Off configuration, with a blue LED indicator and IP65 weatherproof rating. The push-on/push-off latching action toggles the circuit between On and Off states with each press, staying in the selected position until pressed again. Identical in specification to the red ACX3690BL differing only in blue LED illumination it offers an alternative colour option for panels with a blue theme or where different LED colours distinguish switch functions. Chrome plated housing, three blade terminals (common, NO and NC), 19mm mounting hole, 12mm mount length. Covered by a one year warranty. Product overview The ACX3692BL shares every specification with the ACX3690BL 5A at 12V, IP65, chrome plated housing, three blade terminals, 19mm mount hole and 12mm mount length. The only difference is LED colour: red on the ACX3690BL, blue on the ACX3692BL. The blue LED suits panels built around a blue illumination theme, or installations where different colours are used to distinguish switch functions for example, blue for auxiliary circuits and red for warning or power circuits. The latching action means the switch holds its position after being pressed, unlike a momentary switch which only activates while held. The three-terminal configuration provides wiring flexibility: wire between common and NO for standard normally open accessory switching, or between common and NC for a normally closed circuit application. At 5A it handles low-current loads and relay trigger inputs directly. For loads exceeding 5A, the switch should trigger a relay. Features and benefits Latching push On/push Off: Press to toggle between On and Off. Switch holds position without being held down. Not a momentary switch. Blue LED illuminated: Glows when the switch is in the On position. Blue colour for panel theme coordination or function differentiation. IP65 rated: Fully sealed against dust and protected against water jets from any direction. Suited to external mounting and exposed panel locations. Chrome plated housing: Premium finish for custom panels and marine consoles. 3x blade terminals common, NO and NC: Wire between common and NO for standard normally open switching. Wire between common and NC for a normally closed circuit. Full wiring flexibility for both accessory and control circuit applications. 19mm mounting hole: Standard diameter for illuminated push button switches. 12mm mount length: Suits standard panel thicknesses. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3692BL Brand OEX Switch Type Push Button (Latching) Switch Action On/Off (SPST) Poles 1 Positions 2 Current Rating 5A at 12V Voltage 12V Illumination Blue LED IP Rating IP65 Housing Chrome plated Terminals 3x Blade (Common, NO, NC) Mount Diameter 19mm Mount Length 12mm Pack Quantity 1 Weight 0.02kg Warranty One year Sold As Single unit Frequently asked questions Is this a momentary or latching switch? The ACX3692BL is a latching (push On/push Off) switch pressing it toggles the circuit between On and Off states and the switch holds its position until pressed again. It is not a momentary switch; the circuit remains active after the button is released. What are the three terminals for? The three blade terminals are common, normally open (NO) and normally closed (NC). Wire between common and NO for a circuit that is open at rest and closes when the switch is activated standard accessory switching. Wire between common and NC for a circuit that is closed at rest and opens when the switch is activated used in alarm, interlock and control circuit applications. How does the ACX3692BL differ from the ACX3690BL? The ACX3692BL and ACX3690BL are identical in all specifications 5A, 12V, IP65, chrome plated, 3 terminals, 19mm mount, 12mm length. The only difference is LED colour: the ACX3690BL has a red LED and the ACX3692BL has a blue LED. Select based on your panel's colour scheme or function coding convention. What does IP65 mean for this switch? IP65 means the switch is fully protected against dust ingress (6) and against water jets from any direction (5). This makes it suitable for panel locations exposed to rain, splash and wash-down including external vehicle panels, marine consoles and outdoor equipment enclosures. What is the maximum load this switch can handle directly? This switch is rated at 5A at 12V. For loads exceeding 5A, use the switch to trigger a relay rather than wiring the load directly through the switch contacts. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3690BL 12V 5A IP65 Illuminated Latching Push Button Switch Red LED Chrome Housing NO and NC Terminals 19mm Mount The OEX ACX3690BL is a 12V, 5A illuminated latching push button switch in an SPST On/Off configuration, with a red LED indicator and IP65 weatherproof rating. The push-on/push-off latching action toggles the circuit between On and Off states with each press, staying in the selected position until pressed again. Chrome plated housing for a premium appearance suited to custom dash panels, marine consoles and accessory installations where aesthetics matter alongside function. Three blade terminals common, normally open (NO) and normally closed (NC) provide wiring flexibility for both standard and normally closed circuit configurations. 19mm mounting hole, 12mm mount length. Covered by a one year warranty. Product overview The ACX3690BL is a latching switch the circuit stays active after the button is released and remains in the selected state until pressed again. This is the correct choice for circuits that need to stay on without holding the button, as opposed to a momentary switch which only activates while held. The three-terminal configuration provides wiring flexibility. The normally open (NO) terminal creates a circuit that is open at rest and closes when the switch is activated the standard configuration for accessory switching. The normally closed (NC) terminal creates a circuit that is closed at rest and opens when the switch is activated used in alarm, interlock and control circuit applications. This flexibility, combined with the IP65 weatherproofing and chrome housing, makes the ACX3690BL suited to both functional control circuit roles and aesthetically conscious panel builds. At 5A it handles low-current loads and relay trigger inputs directly. For loads exceeding 5A, the switch should trigger a relay. Features and benefits Latching push On/push Off: Press to toggle between On and Off. Switch holds position without being held down. Not a momentary switch. Red LED illuminated: Glows when the switch is in the On position for clear status indication. IP65 rated: Fully sealed against dust and protected against water jets from any direction. Suited to external mounting and exposed panel locations. Chrome plated housing: Premium finish for custom panels and marine consoles. 3x blade terminals common, NO and NC: Wire between common and NO for a standard normally open circuit. Wire between common and NC for a normally closed circuit. Suited to both accessory switching and relay trigger inputs. 19mm mounting hole: Standard diameter for illuminated push button switches. 12mm mount length: Suits standard panel thicknesses. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3690BL Brand OEX Switch Type Push Button (Latching) Switch Action On/Off (SPST) Poles 1 Positions 2 Current Rating 5A at 12V Voltage 12V Illumination Red LED IP Rating IP65 Housing Chrome plated Terminals 3x Blade (Common, NO, NC) Mount Diameter 19mm Mount Length 12mm Pack Quantity 1 Weight 0.02kg Warranty One year Sold As Single unit Frequently asked questions Is this a momentary or latching switch? The ACX3690BL is a latching (push On/push Off) switch pressing it toggles the circuit between On and Off states and the switch holds its position until pressed again. It is not a momentary switch; the circuit remains active after the button is released. What are the three terminals for? The three blade terminals are common, normally open (NO) and normally closed (NC). Wire between common and NO for a circuit that is open at rest and closes when the switch is activated standard accessory switching. Wire between common and NC for a circuit that is closed at rest and opens when the switch is activated used in alarm, interlock and control applications where a closed circuit is the normal state. What does IP65 mean for this switch? IP65 means the switch is fully protected against dust ingress (6) and against water jets from any direction (5). This makes it suitable for panel locations exposed to rain, splash and wash-down including external vehicle panels, marine consoles and outdoor equipment enclosures. What mounting hole does this switch require? The ACX3690BL requires a 19mm round mounting hole with sufficient depth for the 12mm mount length. Confirm both the hole diameter and panel thickness before installation. What is the maximum load this switch can handle directly? This switch is rated at 5A at 12V. For loads exceeding 5A, use the switch to trigger a relay rather than wiring the load directly through the switch contacts. The NO and NC terminal options make it well suited as a relay trigger input. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3609BL 20A Momentary Push Button Switch Off/Momentary On SPST 12V 22mm Mount Water Resistant Bronze Contacts The OEX ACX3609BL is a 20A momentary push button switch in an Off/Momentary On SPST configuration, rated at 12V with a 22mm mounting stem. Unlike a latching switch that stays in position when pressed, a momentary switch is only active while the button is depressed the spring return mechanism automatically restores the Off position the moment it is released. Suited to horn circuits, starter buttons, door release solenoids, relay trigger circuits and momentary accessory activations. Water resistant, bronze contacts, two screw terminals. Fits panels up to 6.35mm thick. Covered by a one year warranty. Product overview A momentary switch produces a brief trigger pulse rather than a sustained on/off state the circuit closes when the button is pressed and opens the instant it is released. This makes the ACX3609BL the correct choice for any application requiring a momentary signal: vehicle horns, engine start buttons, door and gate release solenoids, relay and solenoid coil triggers and light flash circuits. At 20A it can directly switch many loads as well as trigger relay coils for higher-current applications. The 22mm metric thread mounting stem fits panels up to 6.35mm thick with a 22mm diameter hole. The water resistant construction suits outdoor, underbonnet and exposed mounting positions. Bronze contacts provide reliable electrical performance across repeated momentary switching cycles. Two screw terminals allow direct wire connection without crimped connectors. The compact form factor and standard 22mm mount are compatible with a wide range of aftermarket switch panels, consoles and custom fabricated mountings. Features and benefits Momentary On action: Circuit is active only while the button is depressed. Spring return automatically restores Off when released. Not a latching switch. 20A at 12V: Sufficient for direct switching of horns, solenoid coils, relay trigger circuits and moderate accessory loads. Use with a relay for loads exceeding 20A. Water resistant: Suited to outdoor, underbonnet and exposed mounting positions. Bronze contacts: Reliable contact material for repeated momentary switching cycles. 2 screw terminals: Direct wire connection without requiring crimped terminals. 22mm mounting stem with metric thread: Standard panel mount diameter. Fits panels up to 6.35mm thick. Requires 22mm diameter hole. Non-illuminated: Straightforward operation without LED indicator. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3609BL Brand OEX Switch Type Push Button Switch Action Off/Momentary On (SPST) Poles 1 Positions 2 Current Rating 20A at 12V Contacts Bronze Terminals 2x Screw Mount Diameter 22mm Mount Thread 22mm metric Thread Length 6.95mm Maximum Panel Thickness 6.35mm Mount Length 6mm Water Resistant Yes Illumination Non-illuminated Pack Quantity 1 Weight 0.03kg Warranty One year Sold As Single unit Frequently asked questions What is a momentary switch? A momentary switch is only active while it is being physically held in the pressed position. When released, the internal spring returns the button to the Off position and the circuit opens. This differs from a latching switch, which stays in the On position after being pressed. Momentary switches are used wherever a brief trigger pulse is needed rather than a sustained on/off state. What applications is this switch suited to? The ACX3609BL suits any application requiring a momentary trigger: vehicle horns, engine start buttons, door and gate release solenoids, relay trigger circuits, light flash triggers and momentary accessory activation. At 20A it can directly switch many loads as well as trigger relay coils for higher-current applications. What panel thickness does this switch suit? The 22mm metric thread mounting stem is 6.95mm long, fitting panels up to 6.35mm thick. For thicker panels, confirm the stem length is sufficient before purchasing. Can this switch be used for high-current switching? At 20A this switch handles moderate loads directly. For loads exceeding 20A, use the switch as a trigger for a relay or solenoid such as the OEX ACX3322 rather than wiring the main load directly through the switch contacts. Is this switch waterproof or water resistant? The ACX3609BL is water resistant, providing protection against splashing and moisture exposure but not full submersion. For applications requiring a specified IP rating such as IP65 or IP67, a switch with a confirmed weatherproofing rating should be selected. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3438 IP65 Emergency Stop Switch 40mm Mushroom Head Latching Turn-to-Release NC and NO Contacts 3A 12V and 24V The OEX ACX3438 is a 40mm mushroom head emergency stop switch with a latching push button and turn-to-release mechanism, rated at 3A at 12V or 24V. Designed for safety-critical circuit interruption, it provides a clearly visible, easily activated stop function for automotive, marine, caravan and industrial control applications. Once pressed the switch latches in the off state and remains there until deliberately released by rotating the head. Provides both a normally closed (NC) and normally open (NO) contact. IP65 weatherproof enclosure. 69x86mm. Internal or external mount. Covered by a one year warranty. Product overview An emergency stop switch (E-stop) is a safety device designed to interrupt a circuit immediately when activated. The large 40mm mushroom head is highly visible and easy to activate quickly under stress. The latching mechanism means the switch stays in the activated (off) state after being pressed and will not reset automatically the mushroom head must be physically rotated to release the latch before the circuit can be restored, preventing accidental re-energisation after an emergency stop event. The ACX3438 provides two contacts: a normally closed (NC) contact that is connected at rest and opens when the button is pressed, and a normally open (NO) contact that is disconnected at rest and closes when the button is pressed. The NC contact is used to directly break a control circuit on activation. The NO contact is used to signal a controller, relay or alarm. At 3A the ACX3438 is rated for control circuit switching only — it should trigger a relay, contactor or solenoid such as the OEX ACX3322 rather than directly switching a high-current main power load. The IP65 enclosure provides full dust protection and water jet resistance for external and exposed mounting locations. Features and benefits 40mm mushroom head latching push button: Large, highly visible actuator that is easy to activate under stress. Latches in the depressed position on activation. Turn-to-release mechanism: The switch remains latched until the mushroom head is physically rotated to release, preventing accidental re-energisation after an emergency stop event. 1 normally closed (NC) contact: Circuit is closed at rest and opens when the button is pressed. Standard wiring for direct control circuit interruption. 1 normally open (NO) contact: Circuit is open at rest and closes when the button is pressed. Used to signal a controller, relay or alarm on activation. IP65 weatherproof enclosure: Fully sealed against dust and protected against water jets from any direction. Suited to external and exposed mounting locations. 12V and 24V compatible: Suits both passenger vehicle and commercial vehicle systems. 3A rating control circuit switching only: Designed to trigger a relay, contactor or solenoid rather than directly switching a high-current main power load. Pair with the OEX ACX3322 solenoid or a suitable relay for main power interruption. Internal or external mount: Flexible installation for dash panels, control boxes, bulkheads and external equipment enclosures. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3438 Brand OEX Type Emergency Stop Switch Switch Action On/Off, Off/On (Latching) Actuator 40mm mushroom head Activation Push to latch Release Turn to release Contacts 1x Normally Closed (NC), 1x Normally Open (NO) Current Rating 3A Voltage 12V and 24V IP Rating IP65 Mount Options Internal or external Dimensions 69mm x 86mm Illumination Non-illuminated Pack Quantity 1 Weight 0.3kg Warranty One year Sold As Single unit Frequently asked questions What is an emergency stop switch? An emergency stop switch (E-stop) is a safety device designed to interrupt a circuit immediately when activated. The large mushroom head design makes it highly visible and easy to hit quickly in an emergency. The latching mechanism means it stays in the activated (off) state after being pressed the switch must be deliberately rotated to release before the circuit can be restored. What does "turn to release" mean? After the mushroom head is pressed and latches, the switch will not reset automatically. To release the latch and restore the circuit, the mushroom head must be physically rotated (typically clockwise) until it clicks back to the normal position. This deliberate action prevents accidental re-energisation after an emergency stop event. What is the difference between the normally closed and normally open contacts? The normally closed (NC) contact is connected at rest and opens when the button is pressed wiring the circuit through the NC contact will break it immediately on activation. The normally open (NO) contact is disconnected at rest and closes when the button is pressed this is used to signal a controller, relay or alarm on activation. The ACX3438 provides both contacts for flexible integration into control systems. Can this switch directly interrupt a main battery circuit? No. At 3A, this switch is rated for control circuit switching only. It should trigger a relay, contactor or solenoid rather than directly switching the main power load. For main power interruption, pair this switch with a relay or solenoid such as the OEX ACX3322. Is this switch weatherproof? Yes. The IP65 rating confirms full dust protection and resistance to water jets from any direction, making it suitable for external mounting and exposed installation locations including vehicle exteriors, boat applications and equipment enclosures. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3162 600A Heavy Duty Bus Bar Box Red and Black 4x M10 Stud Terminals Glass Fibre Reinforced Nylon 48V DC The OEX ACX3162 is a 600A heavy duty bus bar box combining a red positive bus bar and a black negative bus bar in a single enclosed unit. Four M10 (3/8") stud terminals two red and two black provide a structured, high-current distribution point for 12V, 24V and 48V DC electrical systems. The highest current rating in the OEX bus bar range, suited to high-capacity inverters, large lithium battery banks, commercial vehicle power systems and applications where the combined circuit current approaches or exceeds the 400A limit of the ACX3160. Same 168x80x40mm footprint as the ACX3160 for a like-for-like upgrade. Also available in a 400A version with 8 studs as the ACX3160. Covered by a one year warranty. Product overview The ACX3162 is the highest-rated bus bar box in the OEX range at 600A continuous, stepping up from the 400A ACX3160 for the most demanding installations. There is an important trade-off between the two models: the ACX3162 provides a higher continuous current rating but fewer connection points two red positive and two black negative studs versus four of each on the ACX3160. For installations requiring maximum current capacity with a smaller number of high-current main feeds, the ACX3162 is the correct choice. For installations requiring more individual circuit connections at a lower total current, the ACX3160 with eight studs is more appropriate. The 48V DC voltage rating covers 12V, 24V and 48V systems including lithium battery banks and solar storage installations. Glass fibre reinforced nylon provides heavy duty mechanical strength, electrical insulation and heat and impact resistance. Three sides of the box are open for unobstructed wiring access from multiple directions. At 168x80x40mm it shares the same footprint as the ACX3160, allowing a like-for-like upgrade without changing the mounting arrangement. Features and benefits 600A maximum continuous rating: The highest current rating in the OEX bus bar range, suited to high-capacity inverter installations, large lithium battery banks and commercial vehicle power distribution where the 400A ACX3160 is undersized. 48V DC maximum operating voltage: Compatible with 12V, 24V and 48V DC systems including lithium battery banks and solar storage installations. 4x M10 (3/8") stud terminals two red, two black: Two positive and two negative connection points accepting M10-compatible ring terminals (10.5mm ID or larger). Fewer connection points than the ACX3160 (8 studs) in exchange for higher current capacity. Red and black combined: Both positive and negative bus bars in a single unit for a matched, colour-coded distribution point with instant polarity identification. Glass fibre reinforced nylon construction: High mechanical strength, electrical insulation and resistance to heat and impact in demanding automotive, marine and caravan environments. Three sides open: Unobstructed wiring access from three directions for flexible cable routing and clean cable dressing. 168x80x40mm: Same footprint as the ACX3160 for a like-for-like upgrade without changing the mounting arrangement. Also available in 400A with 8 studs: The ACX3160 provides more individual circuit connections at a lower total current rating. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3162 Brand OEX Type Bus Bar Box Maximum Continuous Rating 600A Maximum Operating Voltage 48V DC Terminal Studs 4x M10 (3/8") 2 red positive, 2 black negative Enclosure Material Glass fibre reinforced nylon Dimensions 168mm x 80mm x 40mm Wiring Access Three sides open Pack Quantity 1 Warranty One year Sold As Single unit Goes well with OEX ACX3057 Ring Crimp Terminal 10.5mm ID Blue, suits M10 stud, pack of 100 OEX ACX3057BL Ring Crimp Terminal 10.5mm ID Blue, suits M10 stud, pack of 14 OEX ACX3160 400A Heavy Duty Bus Bar Box with 8 studs (lower current, more connection points) Frequently asked questions What is a bus bar box used for? A bus bar box provides a centralised, organised distribution point for multiple positive supply and negative return connections in a DC electrical system. Rather than stacking ring terminals at a battery terminal or using individual stud terminals, a bus bar box accepts multiple cables at a purpose-built enclosure, keeping the installation clean and making future maintenance easier. How does the ACX3162 differ from the 400A ACX3160? The ACX3162 is rated at 600A continuous versus 400A for the ACX3160. However, the ACX3162 has 4 stud terminals (2 red, 2 black) while the ACX3160 has 8 (4 red, 4 black). Select the ACX3162 for maximum current capacity with fewer connection points, and the ACX3160 for more individual circuit connections at a lower total current. What ring terminal size suits the M10 studs? The M10 studs are 10mm in nominal diameter and require ring terminals with a 10.5mm or larger ID hole. The OEX ACX3057 (10.5mm ID, blue, pack of 100) and ACX3057BL (pack of 14) are suitable options. Always confirm the ring terminal ID matches the stud diameter before purchasing. What is the maximum voltage for this bus bar? The ACX3162 is rated to 48V DC maximum operating voltage, making it suitable for 12V, 24V and 48V systems including lithium battery banks and solar storage installations. How many circuits can this bus bar support? The ACX3162 has two red positive studs and two black negative studs, allowing up to two positive supply circuits and two negative return circuits to be connected simultaneously. The total combined current across all connections must not exceed 600A continuous. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3160 400A Heavy Duty Bus Bar Box Red and Black 8x M10 Stud Terminals Glass Fibre Reinforced Nylon 48V DC The OEX ACX3160 is a 400A heavy duty bus bar box combining a red positive bus bar and a black negative bus bar in a single enclosed unit. Eight M10 (3/8") stud terminals four red and four black provide a structured, high-current distribution point for 12V, 24V and 48V DC electrical systems. Glass fibre reinforced nylon enclosure with three sides open for unobstructed wiring access. 168x80x40mm. Also available in a 600A version as the ACX3162. Covered by a one year warranty. Product overview A bus bar box provides a centralised, organised distribution point for multiple positive supply and negative return connections in a DC electrical system. Rather than stacking multiple ring terminals on a battery terminal or scattering individual stud terminals across the installation, the ACX3160 consolidates up to four positive supply circuits and four negative return circuits at a single purpose-built enclosure, keeping the installation clean, reducing heat at connection points and making future maintenance and troubleshooting easier. The 400A maximum continuous rating and 48V DC voltage rating cover 12V, 24V and 48V systems including lithium battery banks and solar storage installations. The glass fibre reinforced nylon enclosure provides heavy duty mechanical strength, electrical insulation and durability in underbonnet, marine and caravan environments. Three sides of the box are open for unobstructed wiring access from multiple directions. At 168x80x40mm it suits underbonnet, dual battery and caravan electrical panel installations. For higher current requirements, the ACX3162 provides a 600A alternative. Features and benefits 400A maximum continuous rating: Suited to high-current main supply and earth distribution in dual battery systems, inverter installations and multi-circuit accessory panels. Total combined current across all positive (or negative) connections must not exceed 400A continuous. 48V DC maximum operating voltage: Compatible with 12V, 24V and 48V DC systems including lithium battery banks and solar storage installations. 8x M10 (3/8") stud terminals four red, four positive, four black, four negative: Accepts M10-compatible ring terminals (10.5mm ID or larger) for secure, torque-resistant connections across up to four positive and four negative circuits simultaneously. Red and black combined: Both positive and negative bus bars in a single unit for a matched, colour-coded distribution point with instant polarity identification. Glass fibre reinforced nylon construction: High mechanical strength, electrical insulation and resistance to heat and impact in demanding automotive, marine and caravan environments. Three sides open: Unobstructed wiring access from three directions for flexible cable routing and clean cable dressing. 168x80x40mm: Compact footprint suited to underbonnet, panel and caravan installation spaces. Also available in 600A: The ACX3162 is a 600A version for higher-current applications. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3160 Brand OEX Type Bus Bar Box Maximum Continuous Rating 400A Maximum Operating Voltage 48V DC Terminal Studs 8x M10 (3/8") 4 red positive, 4 black negative Enclosure Material Glass fibre reinforced nylon Dimensions 168mm x 80mm x 40mm Wiring Access Three sides open Pack Quantity 1 Warranty One year Sold As Single unit Goes well with OEX ACX3057 Ring Crimp Terminal 10.5mm ID Blue, suits M10 stud, pack of 100 OEX ACX3057BL Ring Crimp Terminal 10.5mm ID Blue, suits M10 stud, pack of 14 OEX ACX3162 600A Heavy Duty Bus Bar Box (higher current alternative) Frequently asked questions What is a bus bar box used for? A bus bar box provides a centralised, organised distribution point for multiple positive supply and negative return connections in a DC electrical system. Rather than stacking ring terminals on a battery terminal or using individual stud terminals, a bus bar box accepts multiple cables at a purpose-built enclosure, keeping the installation clean and making future maintenance and troubleshooting easier. How many circuits can this bus bar support? The ACX3160 has four red positive studs and four black negative studs, allowing up to four positive supply circuits and four negative return circuits to be connected simultaneously. The total combined current across all positive (or all negative) connections must not exceed 400A continuous. What ring terminal size suits the M10 studs? The M10 studs are 10mm in nominal diameter and require ring terminals with a 10.5mm or larger ID hole. The OEX ACX3057 (10.5mm ID, blue, pack of 100) and ACX3057BL (pack of 14) are suitable options. Always confirm the ring terminal ID matches the stud diameter before purchasing. What is the maximum voltage for this bus bar? The ACX3160 is rated to 48V DC maximum operating voltage, making it suitable for 12V, 24V and 48V systems including lithium battery banks and solar storage installations. Is a higher current version available? Yes. The OEX ACX3162 is a 600A version of this bus bar box for applications requiring higher continuous current capacity. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3146BL 250A Single Stud Terminal Black M8 Stainless Steel Stud on Glass Filled Nylon Base The OEX ACX3146BL is a 250A single stud terminal in black, built around an M8 stainless steel stud mounted on a glass filled nylon base. Designed as a fixed, high-current earth return connection point where multiple ring terminals can be stacked onto the stud and secured with a nut, consolidating multiple negative returns into a single, organised distribution point. The direct earth counterpart to the OEX ACX3145BL red positive terminal. Supplied as a single unit. Covered by a one year warranty. Product overview Running individual earth cables from each circuit back to the battery negative terminal or chassis earth creates a crowded, hard-to-service installation. A dedicated earth stud terminal provides a central negative return point where the main earth lead connects to the stud and each circuit connects its own ring terminal, giving each circuit a clean, individually accessible earth connection without running long cables back to the battery. The 250A rating suits dual battery earth returns, winch negatives, inverter negatives, compressor returns and multi-circuit high-draw loads sharing a common earth rail. The M8 stainless steel stud resists corrosion in underbonnet, marine and caravan environments. The glass filled nylon base provides electrical insulation, mechanical rigidity and heat resistance under sustained load. The black colour follows the standard automotive convention for negative/earth terminals, making the distribution point immediately identifiable. Install alongside the ACX3145BL red positive terminal for a complete, colour-coded positive and negative distribution pair. Features and benefits 250A rating: Suitable for dual battery earth returns, winch negatives, inverter negatives, compressor returns and multi-circuit high-draw loads sharing a common earth rail. M8 stainless steel stud: Corrosion-resistant stud accepting standard M8-compatible ring terminals. Provides a secure, torque-resistant connection point for multiple earth cables stacked with a nut. Glass filled nylon base: Electrically insulating, mechanically robust and heat-resistant. Provides a stable, non-conductive mounting platform for the stud. Black colour coding: Identifies this as a negative/earth distribution terminal per standard automotive wiring convention, distinguishing it from red positive terminals during installation and servicing. Pairs with ACX3145BL: Use together with the red M8 positive terminal for a complete, colour-coded positive and negative distribution point side by side. Single unit: Install individually or alongside the ACX3145BL to build a matched positive and negative distribution pair. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3146BL Brand OEX Type Single Stud Terminal Current Rating 250A Stud Size M8 (8mm) Stud Material Stainless steel Base Material Glass filled nylon Colour Black Pack Quantity 1 Weight 0.06kg Warranty One year Sold As Single unit Goes well with OEX ACX3145BL 250A Single Stud Terminal M8 Red (matching positive terminal) OEX ACX3056 Ring Crimp Terminal 8.4mm ID Blue (suits M8 stud, 1.5 to 2.5mm² cable) OEX ACX3057 Ring Crimp Terminal 10.5mm ID Blue (suits M8 stud, 1.5 to 2.5mm² cable) Frequently asked questions What is a stud terminal used for? A stud terminal provides a fixed, permanent connection point where multiple ring terminals can be stacked onto a single stud and secured with a nut. For earth returns, a stud terminal allows multiple negative cables from different circuits to connect to a single earth point rather than running individual cables all the way back to the battery negative terminal or chassis earth. What ring terminal size suits the M8 stud? The M8 stud is 8mm in nominal diameter. Ring terminals with an 8.4mm ID or larger will fit over the stud. Suitable OEX options include the ACX3056 (8.4mm ID, blue, 1.5 to 2.5mm²) and ACX3057 (10.5mm ID, blue, 1.5 to 2.5mm²). Always confirm the ring terminal ID matches the stud diameter before purchasing. How does this differ from the red ACX3145BL? The ACX3146BL is black, indicating a negative/earth terminal per standard automotive convention. The ACX3145BL is red, indicating a positive/power terminal. Both are otherwise identical in specification 250A, M8 stud, glass filled nylon base, stainless steel construction. Used together they provide a matched, colour-coded positive and negative distribution point. Why is this terminal black? Black is the standard automotive colour convention for negative/earth terminals, distinguishing them from red positive terminals. Colour-coded terminals make it immediately clear which stud is the earth return and which carries positive supply, reducing wiring errors during installation and making future servicing safer. How many ring terminals can be stacked on one stud? The number of ring terminals that can be stacked depends on the stud's threaded length and the combined thickness of the terminal rings and any washers used. Always ensure the nut has sufficient thread engagement when fully tightened. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

OEX ACX3145BL 250A Single Stud Terminal Red M8 Stainless Steel Stud on Glass Filled Nylon Base The OEX ACX3145BL is a 250A single stud terminal in red, built around an M8 stainless steel stud mounted on a glass filled nylon base. Designed as a fixed, high-current connection point where multiple ring terminals can be stacked onto the stud and secured with a nut, consolidating multiple positive supply connections into a single, organised distribution point. Eliminates makeshift stacking at battery terminals and gives each circuit a clean, dedicated connection point. Supplied as a single unit. Covered by a one year warranty. Product overview In dual battery systems, 4WD and caravan builds and marine electrical panels, multiple high-current circuits often need to be connected to the same positive supply point. Stacking ring terminals directly onto a battery positive post creates a crowded, hard-to-service connection that risks overloading the post hardware. A single stud terminal provides a dedicated, remote distribution point where the main battery feed connects to the stud and each individual circuit connects its own ring terminal, giving each circuit a clean, accessible connection that can be removed and reinstalled individually without disturbing the others. The 250A rating suits dual battery main feeds, winch circuits, inverter connections, compressor feeds and other high-draw loads sharing a common positive rail. The M8 stainless steel stud resists corrosion in underbonnet, marine and caravan environments. The glass filled nylon base provides electrical insulation, mechanical rigidity and heat resistance under sustained load. The red colour follows the standard automotive convention for positive terminals, making the distribution point immediately identifiable during installation, inspection and servicing. Features and benefits 250A rating: Suitable for dual battery main feeds, winch circuits, inverter connections, compressor feeds and multi-circuit high-current accessory wiring sharing a common positive rail. M8 stainless steel stud: Corrosion-resistant stud accepting standard M8-compatible ring terminals. Provides a secure, torque-resistant connection point for multiple cables stacked with a nut. Glass filled nylon base: Electrically insulating, mechanically robust and heat-resistant. Provides a stable, non-conductive mounting platform for the stud in underbonnet and exposed installations. Red colour coding: Identifies this as a positive/power distribution terminal per standard automotive wiring convention, distinguishing it from black earth terminals during installation and servicing. Single unit: Install individually or pair with a matching black earth terminal to build a colour-coded positive and negative distribution point. One year warranty: Covered by a one year OEX warranty. Technical specs Specification Detail SKU ACX3145BL Brand OEX Type Single Stud Terminal Current Rating 250A Stud Size M8 (8mm) Stud Material Stainless steel Base Material Glass filled nylon Colour Red Pack Quantity 1 Weight 0.06kg Warranty One year Sold As Single unit Goes well with OEX ACX3056 Ring Crimp Terminal 8.4mm ID Blue (suits M8 stud, 1.5 to 2.5mm² cable) OEX ACX3057 Ring Crimp Terminal 10.5mm ID Blue (suits M8 stud, 1.5 to 2.5mm² cable) Frequently asked questions What is a stud terminal used for? A stud terminal provides a fixed, permanent connection point where multiple ring terminals can be stacked onto a single stud and secured with a nut. In automotive wiring, stud terminals centralise multiple positive supply connections or earth returns at a single point, keeping wiring tidy and reducing the risk of overloading a battery terminal with too many connections. What ring terminal size suits the M8 stud? The M8 stud is 8mm in nominal diameter. Ring terminals with an 8.4mm ID or larger will fit over the stud. Suitable OEX options include the ACX3056 (8.4mm ID, blue, 1.5 to 2.5mm²) and ACX3057 (10.5mm ID, blue, 1.5 to 2.5mm²). Always confirm the ring terminal ID matches the stud diameter before purchasing. Why is this terminal red? Red is the standard automotive colour convention for positive/power terminals, distinguishing them from black negative/earth terminals. Colour-coded terminals make it immediately clear which stud carries positive supply and which is the earth return, reducing wiring errors and making future servicing safer. How many ring terminals can be stacked on one stud? The number of ring terminals that can be stacked depends on the stud's threaded length and the combined thickness of the terminal rings and any washers used. Ensure the nut has sufficient thread engagement when fully tightened. Is a matching black earth terminal available? Check the OEX terminal range for a matching black single stud terminal for the earth/negative counterpart. Building a red/black pair gives a clean, colour-coded positive and negative distribution point for a professional installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less