Rockford Fosgate PMX-2 Punch Marine Compact Digital Media Receiver Full Control, Built Marine Tough Product Overview The Rockford Fosgate PMX-2 is a compact AM/FM/WB digital media receiver purpose-built for marine and motorsport applications. Featuring a 2.7" full-colour TFT display optically wet bonded to eliminate dust and moisture penetration it delivers clear, readable visuals even under direct Australian sun. IPX6 rated and ISO8846/SAE J1171 ignition protection certified, the PMX-2 is engineered to handle the spray, heat, and vibration demands of open water and off-road environments without compromise. At its core, the PMX-2 is a fully featured command centre for any marine or powersport audio system. A 4 x 50W internal amplifier at 2 ohms handles smaller speaker setups directly, while front, rear, and subwoofer RCA preamp outputs allow seamless expansion with aftermarket amplifiers. Bluetooth audio streaming with A2DP and AVRCP support, Pandora internet radio, USB and AUX inputs, a 7-band graphic EQ, on-board Punch EQ control, and selectable crossovers with variable slope give you complete audio management in a single compact unit. Wired remote expansion via optional PMX-series cables makes it adaptable to virtually any vessel layout. Key Specifications Display: 2.7" full-colour TFT with auto-dimming backlight; optically wet bonded IPX6 marine grade rated ISO8846 / SAE J1171 ignition protection certified Internal amplifier: 4 x 50W @ 2 ohms Tuner: AM / FM / WB (Weather Band); multi-region radio frequencies Bluetooth: A2DP and AVRCP wireless streaming with album art support Inputs: USB (with charging), AUX Outputs: Front RCA, Rear RCA, Subwoofer RCA Crossover: Selectable HP / LP / AP with selectable slope 12 / 24 dB/octave EQ: 7-band graphic EQ + on-board Punch EQ control Certifications: FCC, CE, IC, C-Tick Zone control: 1 zone / 1 source (F/R or Sub) Features & Benefits IPX6 marine grade rating: Protected against powerful water jets from any direction. Suitable for open boats, jet skis, and powersport applications where spray and rain are unavoidable on Australian waterways. 2.7" optically wet bonded full-colour TFT display: The wet bonding process eliminates the air gap between the display layers, preventing fogging, dust infiltration, and moisture ingress. Auto-dimming backlight ensures readability from direct sun to night running. ISO8846 / SAE J1171 ignition protection certified: Meets internationally recognised marine ignition protection standards, reducing the risk of ignition in fuel-vapour environments critical for petrol-powered vessels. 4 x 50W internal amplifier @ 2 ohms: Enough output to drive a set of marine speakers directly without an external amplifier. When more power is needed, front, rear, and subwoofer RCA outputs allow straightforward amplifier integration. Bluetooth A2DP and AVRCP streaming with album art: Stream audio wirelessly from smartphones and compatible devices with full playback control and album art display. Ideal for helm-mounted use where keeping a phone out of spray is preferred. Pandora internet radio and iPod playback: Broad source compatibility for Australian users, supporting popular streaming and device playback with on-screen display controls. 7-band graphic EQ and on-board Punch EQ: Precise audio tuning without an external processor. Dial in the right sound for open-air marine environments where acoustics differ significantly from enclosed vehicle cabins. Selectable HP / LP / AP crossovers with 12 / 24 dB/octave slope: Flexible crossover control for full-range, mid, and subwoofer speaker management from a single head unit. Reduces the need for additional signal processors. Independent subwoofer level control: Adjust bass output separately from the main volume without diving into menus convenient at the helm during use. Water-resistant rotary encoder knob with white LED illumination: Tactile, reliable volume and control operation in wet conditions, with clear visibility for night use on the water. USB input with charging: Charge devices while playing audio. Keeps phones and navigation devices topped up during longer runs. Wired remote expansion capability: Compatible with optional PMX-series extension cables and remotes (PMX-1R, PMX-0R) for mounting secondary controls at a second helm station or convenient location on the vessel. EEPROM memory system: Retains settings and station presets even after power is disconnected useful on vessels where battery isolation is standard practice. Custom GUI interface: User-configurable display interface for a personalised look and easier day-to-day operation. Low voltage warning alert: Notifies you when system voltage drops below safe operating levels, protecting your vessel's battery and electronics during extended use. Multi-region radio frequencies: Supports radio frequency ranges across multiple regions, making the PMX-2 suitable for Australian-market use out of the box. Technical Specs Specification Detail SKU PMX-2 Brand Rockford Fosgate Display 2.7" full-colour TFT; optically wet bonded; auto-dimming backlight IPX Rating IPX6 Ignition Protection ISO8846 / SAE J1171 certified Internal Amplifier 4 x 50W @ 2 ohms Tuner AM / FM / WB (Weather Band) Radio Frequencies Multi-region Bluetooth A2DP + AVRCP (album art support) Pandora Yes iPod Playback Yes (on-screen display) Inputs USB (with charging), AUX Signal Outputs Front RCA, Rear RCA, Subwoofer RCA Crossover Selectable HP / LP / AP; 12 / 24 dB/octave slope EQ 7-band graphic EQ + on-board Punch EQ Subwoofer Level Control Independent; front-mounted Zone Control 1 zone / 1 source (F/R or Sub) Control Knob Water-resistant rotary encoder; white LED illumination Memory EEPROM GUI Custom interface Low Voltage Warning Yes Remote Expansion Yes compatible with PMX-series remotes and extension cables Antenna Not included Certifications FCC, CE, IC, C-Tick, ISO8846, SAE J1171 Dimensions Confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Rockford Fosgate PMX-1R Punch Marine wired remote Rockford Fosgate PMX-0R Punch Marine remote Rockford Fosgate PMX10C, PMX16C, PMX25C extension cables Rockford Fosgate Punch and Prime marine amplifiers (via RCA preamp outputs) Rockford Fosgate marine subwoofers and full-range marine speakers Marine vessels: bow riders, pontoons, centre console fishing boats, ski boats, and tinnies Powersport applications: UTVs, side-by-sides, dune buggies, and off-road 4WDs Smartphones and Bluetooth-enabled devices (A2DP/AVRCP streaming) iPod and compatible Apple devices (via USB) Frequently Asked Questions Is the PMX-2 suitable for open-water marine use in Australia? Yes. The PMX-2 is IPX6 rated and ISO8846/SAE J1171 ignition protection certified, making it suitable for open boats, jet skis, and powersport applications exposed to spray, rain, and marine fuel-vapour environments. Does the PMX-2 have enough power to run speakers without an external amplifier? Yes. The built-in 4 x 50W amplifier at 2 ohms can drive marine speakers directly. For higher output or subwoofer integration, front, rear, and subwoofer RCA outputs allow connection to aftermarket amplifiers. Can I control the PMX-2 from a second location on my vessel? Yes. The PMX-2 supports wired remote expansion via optional PMX-series remotes (PMX-1R, PMX-0R) and extension cables (PMX10C, PMX16C, PMX25C), allowing secondary control from a second helm station or convenient mounting point. Does the PMX-2 support Bluetooth streaming from a smartphone? Yes. The PMX-2 features A2DP and AVRCP Bluetooth, supporting wireless audio streaming with full playback control and album art display from compatible smartphones and devices. Is an antenna included with the PMX-2? No. A compatible marine AM/FM/WB antenna is required for tuner functionality and must be purchased separately. Confirm antenna compatibility with your supplier or installer prior to purchase. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate T1S-1X12 Power 12" T1 Slim Sealed Loaded Enclosure Big Thump, Slim Footprint Product Overview The Rockford Fosgate T1S-1X12 is a factory-loaded sealed enclosure housing a single 12" Power T1 slim subwoofer with a 600 Watt RMS power handling capacity. Designed specifically for under-seat and behind-seat truck installations where depth is restricted but output expectations are anything but, the T1S-1X12 delivers the deep, solid thump characteristic of a sealed enclosure without demanding the space of a traditional subwoofer box. Pre-wired to 1 ohm straight from the factory, the T1S-1X12 is ready to be pushed hard by a compatible mono amplifier no internal wiring, no driver installation, and no enclosure building required. The slim-line wedge profile is constructed from 5/8" MDF with a premium black carpet finish and stitched Rockford Fosgate logo, and ships complete with a grille for immediate, professional-looking installation in utes, SUVs, and cab-style vehicles across Australia. Key Specifications Subwoofer: Single 12" Rockford Fosgate Power T1 slim Power handling: 600W RMS Pre-wired impedance: 1 ohm Enclosure type: Sealed Enclosure design: Slim-line wedge (truck/under-seat style) Construction: 5/8" MDF Finish: Black carpet with black stitching and Rockford Fosgate logo Input terminals: 12 AWG spring-loaded quick-release Grille: Included Features & Benefits 600W RMS power handling: The T1S-1X12 is built to take serious power. Paired with a compatible 600W mono amplifier, it delivers the kind of authoritative bass output that belies its slim profile ideal for Australian ute and SUV builds where space is tight but bass expectations are high. Pre-wired to 1 ohm: Factory pre-wired to a 1-ohm load, the T1S-1X12 is ready to maximise output from a compatible mono amplifier straight out of the box. No internal wiring configuration required connect your amplifier and go. Sealed enclosure for deep, tight bass: The sealed design produces the deep, solid thump preferred by enthusiasts who want accurate, controlled bass response rather than the louder but less precise output of a ported enclosure. Ideal for rock, hip-hop, and bass-heavy Australian country and electronic music genres. Slim-line wedge profile: Purpose-designed for behind-seat and under-seat installation in utes, trucks, and cab-style vehicles. The wedge shape maximises internal enclosure volume within a minimal height footprint, fitting where standard subwoofer boxes simply cannot. 5/8" MDF construction: Medium-density fibreboard walls provide the rigidity and resonance control needed for accurate bass reproduction, minimising enclosure flex and unwanted panel vibration at high output levels. Premium black carpet with stitched Rockford Fosgate logo: A factory-finished appearance that looks purpose-built rather than aftermarket. The black carpet and black stitching integrate cleanly into the interiors of most Australian utes and SUVs. 12 AWG spring-loaded quick-release input terminals: Tool-free wiring connection and disconnection. Practical for installs where the enclosure may need to be temporarily removed common in ute tray and cab configurations. Grille included: Ships with a protective grille fitted, ready for immediate installation without sourcing additional accessories. Complete loaded enclosure: Subwoofer, enclosure, wiring, and grille are all included. No separate driver purchase, no box building, and no guesswork on enclosure tuning a complete plug-and-play subwoofer solution. Technical Specs Specification Detail SKU T1S-1X12 Brand Rockford Fosgate Subwoofer Driver 12" Rockford Fosgate Power T1 Slim Power Handling 600W RMS Pre-Wired Impedance 1 ohm Enclosure Type Sealed Enclosure Style Slim-line wedge (truck/under-seat) Construction Material 5/8" MDF Finish Black carpet; black stitching Logo Stitched Rockford Fosgate logo Input Terminals 12 AWG spring-loaded quick-release Grille Included Dimensions Confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Rockford Fosgate Power and Punch series mono amplifiers rated at 600W RMS into 1 ohm Utes, trucks, and dual-cab vehicles with behind-seat or under-seat storage space SUVs and wagons with underfloor or rear cargo area installations Vehicles requiring a slim subwoofer solution where standard enclosure depth is not available Rockford Fosgate wiring kits and RCA cables for amplifier integration Frequently Asked Questions What amplifier do I need for the T1S-1X12? The T1S-1X12 is pre-wired to 1 ohm and handles 600W RMS. A mono amplifier stable at 1 ohm and rated at or near 600W RMS is recommended for optimal performance such as a compatible Rockford Fosgate Power or Punch mono amplifier. Will the T1S-1X12 fit behind the seat of my ute or dual-cab? The T1S-1X12 is specifically designed for behind-seat and under-seat truck and ute installations using a slim-line wedge profile. Confirm the exact enclosure dimensions with your supplier and measure your available space before purchase, as dimensions vary between vehicle models. Is the T1S-1X12 a ported or sealed enclosure? It is a sealed enclosure. Sealed designs deliver deep, tight, and accurate bass with a solid thump character preferred for music genres and listeners who prioritise bass quality and control over maximum volume output. Does the T1S-1X12 come with a subwoofer already installed? Yes. The T1S-1X12 is a fully loaded enclosure the 12" Power T1 slim subwoofer is factory-installed, pre-wired to 1 ohm, and ships with a grille included. Connect your amplifier to the spring-loaded input terminals and it is ready to use. Can I rewire the T1S-1X12 to a different impedance? The T1S-1X12 ships pre-wired to 1 ohm. Rewiring to a different impedance depends on the voice coil configuration of the installed T1 slim driver. Confirm the driver's voice coil specification with your supplier or installer before attempting any rewiring. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate T1S-1X10P Power 10" 500 Watt Slim Vented Loaded Enclosure Built for truck installs that demand serious output without sacrificing cabin space, the T1S-1X10P pairs a Power T1 slim 10" subwoofer with a precision-tuned vented wedge enclosure rated at 500 watts RMS and configured for maximum current at 1 ohm. Product Overview The T1S-1X10P is Rockford Fosgate's loaded slim vented enclosure from the Power Series, housing the T1S1-10 Power T1 slim 10" subwoofer in a wedge-profile MDF box designed specifically for behind-seat truck installations where depth is limited. Despite the slim-line footprint, the enclosure is vented through a high-flow, low-noise slotted port that is tuned to enhance hard-hitting, boomy bass frequencies rather than the tighter, more controlled output of a sealed design. The 1-ohm nominal impedance configuration allows the T1S1-10 driver to be pushed with serious amplifier power, with 500 watts RMS and 1000 watts peak power handling supported from within a compact wedge profile. The enclosure is constructed from 5/8" MDF and finished in black carpet with black stitched Rockford Fosgate logo detailing. Spring-loaded 12 AWG input terminals provide quick-release connectivity, and a grille is included for driver protection. Klippel verified and CEA-2031 compliant, with a 1-year warranty. Features & Benefits Power T1 Slim Subwoofer with 500W RMS Power Handling: The T1S1-10 Power T1 slim driver is rated at 500 watts RMS and 1000 watts peak, delivering Power Series output capacity from a subwoofer specifically designed for minimum-depth enclosures. Klippel verification confirms the driver's performance parameters have been measured and optimised for accuracy at high excursion levels. Vented Wedge Enclosure Tuned for Hard-Hitting Bass: The slotted port is tuned specifically to enhance hard-hitting, boomy bass frequencies, making the T1S-1X10P the preferred choice for listeners who want maximum impact and low-frequency punch rather than tight, sealed-box accuracy. High-Flow, Low-Noise Slotted Vent: The slotted port design maximises airflow through the enclosure at resonance while minimising port noise and chuffing at high output levels, maintaining clean bass output as amplifier power increases. 1-Ohm Nominal Impedance: The 1-ohm configuration allows the T1S-1X10P to be driven directly from a monoblock amplifier at its lowest stable impedance, maximising available output power from compatible amplifiers and delivering the kind of output associated with a much larger system. Slim-Line Wedge Profile for Truck Behind-Seat Installation: The wedge dimensions of 4.2" x 6.3" depth and 14.5" height allow the T1S-1X10P to fit behind the seats of most trucks without consuming the cab's usable passenger or storage space. 5/8" MDF Construction: The enclosure is constructed from 5/8" Medium Density Fiberboard, providing structural rigidity and acoustic mass suited to vented subwoofer enclosure requirements. 12 AWG Spring-Loaded Input Terminals: The spring-loaded terminal design accepts wire up to 12 AWG and provides a quick-release connection for easy installation or removal without tools. Black Carpet Finish with Stitched Logo: The premium black carpet finish with black-stitched Rockford Fosgate logo detailing provides a clean, finished appearance suited to in-cabin truck installations. Grille Included: A grille is included in the box for full driver protection after installation. CEA-2031 Compliant: Woofer power handling conforms to CEA-2031 industry standards, confirming the 500W RMS rating is a real, tested figure. Technical Specs Specification Detail SKU T1S-1X10P Series Power Woofer Size 10" Woofer Quantity 1 Woofer Series Power T1S (T1S1-10) Power Handling (RMS) 500W Power Handling (Peak) 1000W Nominal Impedance 1 Ohm Frequency Response 20 Hz - 200 Hz Enclosure Type Vented (Shallow Wedge) Enclosure Material 5/8" MDF Enclosure Finish Black Carpet with Black Stitching Speaker Connector Spring-loaded, up to 12 AWG Grille Included Dimensions (H x W x D1 x D2) 14.5" x 31.5" x 4.2" x 6.3" (37.0 cm x 80.0 cm x 10.7 cm x 15.9 cm) Shipping Weight 36 lbs (16.3 kg) Compliance CEA-2031, Klippel Verified Warranty 1 Year Goes Well With The T1S-1X10P operates at 1 ohm and handles 500 watts RMS, requiring a monoblock amplifier that is stable at 1 ohm with sufficient output to drive it effectively. Rockford Fosgate's R2-1200X1 is a well-matched amplifier option, delivering substantial power at 1 ohm from within the Prime Series range. A 4-gauge amplifier wiring kit is required for the power and ground run, and a quality RCA interconnect from the head unit's subwoofer pre-out is the recommended signal source connection. For truck installations requiring front and rear speaker amplification alongside the T1S-1X10P, a separate 4-channel amplifier such as the R2-300X4 or R2-200X2 connected via the monoblock's RCA pass-through is the recommended approach. Frequently Asked Questions Is the T1S-1X10P a sealed or vented enclosure, and how does that affect the bass character? The T1S-1X10P is a vented enclosure, using a high-flow slotted port tuned to enhance hard-hitting, boomy low-frequency output. This makes it the preferred choice for listeners who want maximum impact and low-frequency punch. For tighter, more controlled bass with greater transient accuracy, a sealed enclosure would be the alternative. Rockford Fosgate's P300-10T is an example of a sealed powered truck enclosure if a different bass character is preferred. What amplifier is required, and what impedance does the T1S-1X10P present? The T1S-1X10P is configured at 1-ohm nominal impedance, requiring a monoblock amplifier that is rated stable at 1 ohm. Confirm the amplifier's 1-ohm stability rating before purchase, as not all monoblock amplifiers support 1-ohm operation. At 500 watts RMS power handling, the amplifier should be capable of delivering at least 500 watts at 1 ohm for the driver to reach its rated output. Does the T1S-1X10P include a grille and all hardware needed for installation? Yes. The T1S-1X10P includes a grille for driver protection and spring-loaded 12 AWG input terminals are built into the enclosure. An amplifier, amplifier wiring kit, and RCA interconnect are required separately for a complete installation. Will the T1S-1X10P fit behind the seat of my truck? The T1S-1X10P measures 14.5" high, 31.5" wide, and has a wedge depth ranging from 4.2" to 6.3". These dimensions are designed for common truck behind-seat applications, but clearance varies by vehicle. Measure the available space behind the seat in your specific truck before purchase to confirm the enclosure will fit without obstructing the seat's range of movement. What does Klippel verification mean for the T1S1-10 driver? Klippel is an independent speaker measurement and certification programme that identifies and corrects non-linear distortion parameters in speaker drivers, including suspension non-linearities and motor force variation across the cone's travel range. Klippel verification on the T1S1-10 driver confirms that its performance parameters have been accurately measured and optimised, ensuring the driver delivers clean, low-distortion output at the high excursion levels produced at 500 watts RMS. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate P3S-1X12 Punch P3 Shallow 12" Sealed Loaded Enclosure 400 Watts, Slim Fit, Serious Output Product Overview The Rockford Fosgate P3S-1X12 is a factory-loaded sealed enclosure housing a single Punch P3S shallow 12" subwoofer (P3SD2-12) rated at 400 Watts RMS and 800 Watts peak. Internally pre-wired to a 1-ohm load, it is designed to be driven hard by a compatible high-output mono amplifier delivering genuine P3-level bass performance from a slim-line wedge enclosure purpose-built for behind-seat and under-seat truck and ute installations where depth is the critical constraint. The P3S-1X12 steps up significantly from the T1S-1X12 in both power handling and driver pedigree, housing the Punch P3S shallow driver in a computer-optimised sealed enclosure constructed from 5/8" MDF. High-density carpet with a stitched Diamond-R logo, Rockford Fosgate speaker cable internal wiring, and 10 AWG quick-release compression input terminals complete a loaded enclosure that looks and performs as a premium, purpose-built solution. A trim ring is included, ready to accept an optional stamped mesh grille insert for a finished, professional appearance. Key Specifications Subwoofer: Single 12" Rockford Fosgate Punch P3S shallow (P3SD2-12) Power handling: 400W RMS / 800W peak Pre-wired impedance: 1 ohm (internally wired) Enclosure type: Sealed shallow wedge Construction: 5/8" MDF Finish: High-density carpet with stitched Diamond-R logo Internal wiring: Rockford Fosgate speaker cable Input terminals: 10 AWG quick-release compression Trim ring: Included (accepts optional stamped mesh grille insert) Dimensions (H x W x D1 x D2): 34.29 x 69.59 x 13.46 x 8.38 cm (wedge) Shipping weight: 12.24 kg Features & Benefits 400W RMS / 800W peak power handling: The P3S-1X12 is built for serious amplifier output. Pre-wired to 1 ohm, it is ready to extract maximum power from a compatible high-output mono amplifier delivering P3-level bass performance that goes well beyond entry-level slim enclosure solutions. Punch P3S shallow 12" driver (P3SD2-12): The P3S series shallow driver is purpose-engineered for reduced mounting depth without the performance compromises of a standard driver in an undersized box. The result is deeper, tighter bass from a slim profile than a generic shallow woofer can achieve. Pre-wired to 1 ohm: Factory internal wiring to 1 ohm maximises power delivery from compatible mono amplifiers. No internal wiring configuration required connect your amplifier to the 10 AWG input terminals and go. Computer-optimised sealed enclosure design: The enclosure volume and geometry are calculated specifically for the P3S driver, ensuring the sealed alignment produces the accurate, punchy bass response the P3 series is built for not a generic box tuned to approximate specifications. Slim-line wedge profile: The wedge shape (D1: 13.46 cm / D2: 8.38 cm) maximises internal volume within the minimum possible height, fitting behind and under seats in utes, trucks, and dual-cab vehicles where standard enclosure depth is not available. 5/8" MDF construction: Rigid enclosure walls minimise flex, resonance, and panel vibration at the high output levels the P3S-1X12 is designed to handle. Essential for accurate bass reproduction at 400W RMS continuous input. High-density carpet with stitched Diamond-R logo: Premium factory finish that integrates cleanly into vehicle interiors. The high-density carpet is more durable and resistant to wear than standard carpet finishes, suited to daily ute and truck cab use. Rockford Fosgate speaker cable internal wiring: Factory-installed Rockford Fosgate cable ensures signal integrity from the input terminals to the driver. No compromises from generic or undersized internal wiring at the 1-ohm, high-current load this enclosure operates at. 10 AWG quick-release compression input terminals: Heavier gauge than the 12 AWG terminals found on lower-spec loaded enclosures, appropriate for the higher current demands of a 400W RMS, 1-ohm system. Tool-free quick-release operation for clean installation and removal. Included trim ring with optional grille compatibility: The trim ring ships in the box and is ready to accept a separately available stamped mesh grille insert for a factory-finished, professional appearance once installed. Technical Specs Specification Detail SKU P3S-1X12 Brand Rockford Fosgate Subwoofer Driver 12" Rockford Fosgate Punch P3S shallow (P3SD2-12) Woofer Quantity 1 Power Handling 400W RMS / 800W peak Pre-Wired Impedance 1 ohm (internally wired) Enclosure Type Sealed shallow wedge Construction Material 5/8" MDF Finish High-density carpet; stitched Diamond-R logo Internal Wiring Rockford Fosgate speaker cable Input Terminals 10 AWG quick-release compression Trim Ring Included (accepts optional stamped mesh grille) Grille Optional stamped mesh grille insert (sold separately) Enclosure Design Computer-optimised Dimensions (H x W x D1 x D2) 34.29 x 69.59 x 13.46 x 8.38 cm (wedge) Shipping Weight 12.24 kg Warranty Confirm with supplier Compatible With Mono amplifiers stable at 1 ohm, rated at up to 400W RMS for optimal performance Utes, trucks, and dual-cab vehicles with behind-seat or under-seat storage space SUVs and wagons requiring a slim sealed subwoofer solution Rockford Fosgate Power and Punch series mono amplifiers Optional Rockford Fosgate stamped mesh grille insert (sold separately confirm part number with supplier) Rockford Fosgate wiring kits and RCA cables for amplifier integration Frequently Asked Questions What amplifier does the P3S-1X12 require? The P3S-1X12 is pre-wired to 1 ohm and handles 400W RMS. A mono amplifier stable at 1 ohm and rated at or near 400W RMS is recommended such as a compatible Rockford Fosgate Power or Punch mono amplifier. Do not exceed 800W peak input. How does the P3S-1X12 compare to the T1S-1X12? Both are slim sealed loaded enclosures pre-wired to 1 ohm for behind-seat ute and truck installs. The P3S-1X12 steps up with a higher-pedigree Punch P3S shallow driver, 400W RMS power handling (vs 600W for the T1S), and heavier 10 AWG input terminals confirm the T1S-1X12 power spec with your supplier when comparing the two. Will the P3S-1X12 fit behind the seat of my ute or dual-cab? The P3S-1X12 uses a wedge profile measuring 34.29 cm high, 69.59 cm wide, and 13.46 to 8.38 cm deep. Measure your available behind-seat or under-seat space carefully against these dimensions before purchase, as clearance varies between vehicle models. Is a grille included with the P3S-1X12? A trim ring is included, ready to accept an optional stamped mesh grille insert. The grille itself is sold separately confirm the compatible part number with your supplier. What does the computer-optimised design mean for bass performance? It means the enclosure volume and geometry are calculated specifically for the P3S shallow driver rather than being a generic box. This results in a sealed alignment that accurately matches the driver's parameters, producing tighter, deeper, and more accurate bass than a non-optimised enclosure of similar size. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

6.5" T4 Component System LCP Fibre Sandwich Cone, Multi-Pole™ Neodymium Motor, 1" Ring Radiator LCP Tweeter, VAST, Asymmetrical 12dB/Octave Crossover, Bi-Amp Capable. Product Overview The Rockford Fosgate Power T4652-S is a 6.5" 2-way audiophile component system from the T4 series described by Rockford Fosgate as a design that mimics the performance of the flagship T5 model. The kit includes two woofers with grilles, two tweeters, a passive crossover, and mounting hardware. Power handling (RMS) is not stated in the supplier data confirm with Rockford Fosgate before publishing. The T4652-S introduces several construction elements not found in the T3 series: an LCP fibre sandwich woofer cone (layered composite rather than single-material LCP), a Multi-pole™ neodymium motor structure for improved linearity, a FlexFit slot basket, and a 1" ring radiator LCP dome tweeter with an aluminium (not Mylar) phase plug. The asymmetrical 12dB/octave Butterworth crossover provides ±2dB selectable tweeter level settings, bi-amp switching, and on/off-axis configuration. The VAST butyl rubber surround and die-cast aluminium frame are confirmed. Key Specifications Woofer size: 6.5 inch Configuration: 2-way component Power handling (RMS): Not specified Impedance: Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Woofer mounting depth: Not specified — confirm with Rockford Fosgate Woofer cone: LCP fibre sandwich (layered composite) Woofer motor: Multi-pole™ neodymium Woofer frame: Die-cast aluminium Woofer surround: VAST butyl rubber ✓ Spider: Fatigue and tear resistant linear Nomex Basket: FlexFit slot Tweeter: 1" (25mm) ring radiator LCP dome, aluminium phase plug, neodymium (implied) Tweeter mounting: DDC (Discrete Dual Clamp) — flush and surface (angled) Crossover: External passive, asymmetrical 12dB/octave Butterworth Crossover frequencies: Not specified — confirm with Rockford Fosgate Tweeter level: Selectable +2dB / 0dB / -2dB ✓ Bi-amp capability: Yes (selectable) On/off-axis: Yes (selectable) Grilles: Included ✓ Mounting hardware: Included ✓ Kit contents: 2 woofers + 2 tweeters + crossover + grilles + hardware CEA-2031 compliant: Not stated — confirm with Rockford Fosgate Cutout diameter: Not specified — confirm with Rockford Fosgate Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits LCP Fibre Sandwich Cone — A sandwich cone construction bonds multiple layers together — typically a rigid outer skin material and a lightweight core — to produce a cone that is stiffer than a single-material design of equivalent mass. The LCP fibre outer layers provide exceptional stiffness and damping; the sandwich structure adds rigidity in the direction perpendicular to the cone face, reducing cone breakup modes for more accurate midrange reproduction. Multi-Pole™ Neodymium Motor Structure — Rockford Fosgate's proprietary Multi-Pole™ motor uses multiple pole pieces in the magnetic circuit rather than the conventional single-pole design — producing a more uniform magnetic field across the voice coil's working range and reducing the nonlinear distortion associated with voice coil position variation in the magnetic gap. This is a proprietary Rockford Fosgate technology. 1" Ring Radiator LCP Dome Tweeter with Aluminium Phase Plug — A ring radiator tweeter produces sound from an annular (ring-shaped) diaphragm rather than a full dome face — allowing the centre of the tweeter to be acoustically transparent (via the phase plug). This design produces very even high-frequency dispersion and extended high-frequency response, as the ring geometry allows the diaphragm to move as a more ideal piston at high frequencies. The aluminium phase plug guides high-frequency waves toward the listener while providing thermal management. FlexFit Slot Basket — The slot-type FlexFit basket incorporates openings in the basket wall that allow air movement and facilitate OEM mounting in cavities where a solid basket wall would obstruct the door structure. A different construction approach from the standard FlexFit basket. VAST Butyl Rubber Surround — VAST geometry confirmed with butyl rubber surround material — providing the increased effective cone area of VAST with the UV resistance and temperature stability of butyl rubber. Die-Cast Aluminium Frame — Dense, dimensionally precise die-cast aluminium basket for rigid driver geometry and reduced resonance. Fatigue-Resistant Linear Nomex Spider — Aromatic polyamide spider for consistent compliance and fatigue resistance at sustained high-power levels. Asymmetrical 12dB/Octave Butterworth Crossover — The Butterworth alignment produces a maximally flat frequency response through the crossover region. The asymmetrical description indicates the slopes or filter characteristics differ between the woofer and tweeter channels — exact crossover frequencies and the nature of the asymmetry are not confirmed in the supplier data. ±2dB Tweeter Level, Bi-Amp, On/Off-Axis — The same installer-friendly crossover flexibility as the T3 series: ±2dB tweeter attenuation, bi-amp capability, and on/off-axis optimisation for different tweeter mounting positions. Technical Specs Specification Detail Brand Rockford Fosgate Part Number T4652-S Series Power T4 Woofer Size 6.5 inch Configuration 2-Way Component Power Handling (RMS) Not confirmed Impedance Not specified — confirm with Rockford Fosgate Sensitivity Not specified — confirm with Rockford Fosgate Frequency Response Not specified — confirm with Rockford Fosgate Woofer Mounting Depth Not specified — confirm with Rockford Fosgate Woofer Cone LCP Fibre Sandwich ✓ Woofer Motor Multi-Pole™ Neodymium ✓ Woofer Frame Die-Cast Aluminium ✓ Woofer Surround VAST Butyl Rubber ✓ Spider Fatigue-Resistant Linear Nomex ✓ Basket FlexFit Slot ✓ Tweeter 1" (25mm) Ring Radiator LCP Dome, Aluminium Phase Plug ✓ Tweeter Mounting DDC (Flush and Surface/Angled) Crossover External Passive, Asymmetrical 12dB/Octave Butterworth ✓ Crossover Frequencies Not specified — confirm with Rockford Fosgate Tweeter Level +2dB / 0dB / -2dB selectable ✓ Bi-Amp Capability Yes (selectable) ✓ On/Off-Axis Yes (selectable) ✓ Grilles Included ✓ Mounting Hardware Included ✓ CEA-2031 Compliant Not confirmed Cutout Diameter Not specified — confirm with Rockford Fosgate Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable installation: 6.5" front door speaker positions — premium audiophile front stage builds Kick panel or A-pillar tweeter positions (on/off-axis optimised) Bi-amp configurations with dedicated woofer and tweeter channels Pairs well with: Rockford Fosgate T-series 4-channel amplifiers for passive operation Dedicated amplifier channels for bi-amp front stage configuration Rockford Fosgate T-series subwoofer amplifier and subwoofer for full system Frequently Asked Questions What is an LCP fibre sandwich cone? A sandwich cone construction bonds multiple material layers — in this case, LCP (Liquid Crystal Polymer) fibre forming the outer skins with a core material between them. LCP fibre provides exceptional stiffness and low mass; the sandwich geometry adds rigidity perpendicular to the cone face, which resists cone breakup (the deformation that causes distortion at high output levels and high frequencies) more effectively than a single-material cone. What is the Multi-Pole™ neodymium motor? Multi-Pole™ is Rockford Fosgate's proprietary motor structure that uses multiple pole pieces in the magnetic circuit. This produces a more uniform magnetic field across the voice coil's working excursion range — reducing the position-dependent distortion (inductance variation) that occurs in conventional single-pole motor designs. The result is lower harmonic and intermodulation distortion throughout the driver's operating range. What is a ring radiator tweeter? A ring radiator produces sound from an annular (ring-shaped) diaphragm rather than from the full surface of a conventional dome. The centre of the tweeter is occupied by the phase plug rather than driven diaphragm material. This design produces a more even and extended high-frequency dispersion pattern, as the ring geometry allows the diaphragm to behave more like an ideal piston at high frequencies without the cone breakup modes that affect large dome areas. The aluminium phase plug guides the high-frequency output toward the listener. What is the crossover configuration on the T4652-S? An asymmetrical 12dB/octave Butterworth crossover. The Butterworth alignment produces maximally flat frequency response through the crossover region. The asymmetrical description indicates the filter characteristics differ between the woofer and tweeter channels — exact crossover frequencies and the specific nature of the asymmetry must be confirmed from the official Rockford Fosgate T4652-S datasheet. What power handling does the T4652-S have? Power handling (RMS) is not stated in the supplier data for the T4652-S. This is a critical purchasing specification — confirm with Rockford Fosgate or from the official T4652-S datasheet before purchasing to ensure amplifier compatibility. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Punch Pro Passive Crossover 125W RMS, 3kHz 6dB/Octave Low-Pass, Dual Woofer Outputs, Selectable Tweeter Attenuation. For Punch Pro Speakers Only. Sold Individually. Product Overview The Rockford Fosgate Punch Pro PP4-X is a passive crossover unit designed exclusively for use with Rockford Fosgate Punch Pro 4-Ohm midrange drivers and tweeters it is not a universal crossover and is not compatible with other brands or other Rockford Fosgate series. The PP4-X must be used in conjunction with the built-in 6dB/octave high-pass crossover in the Punch Pro tweeter the two crossovers work as a system to divide the frequency spectrum between the woofer and tweeter outputs. The PP4-X handles the woofer channel: it provides a 6dB/octave low-pass filter at 3kHz to two woofer outputs, limiting the frequency content delivered to the Punch Pro midrange drivers. Selectable tweeter impedance (4-Ohm or 8-Ohm) and tweeter attenuation (0dB, -3dB, -6dB) allow the system's tweeter level to be adjusted relative to the midrange output accommodating different installation positions and sensitivity matching requirements. Rated at 125W RMS (250W peak), the PP4-X matches the power handling of the Punch Pro midrange driver. Sold as an individual unit. Key Specifications Part type: Passive crossover Compatible with: Rockford Fosgate Punch Pro 4-Ohm speakers only Power handling (RMS): 125W Power handling (peak): 250W Woofer impedance: 4-Ohm (required) Woofer outputs: 2 (dual — for two Punch Pro midrange drivers) Low-pass filter: 6dB/octave at 3kHz Tweeter high-pass: Provided by built-in PP4-T tweeter crossover (not in PP4-X) Tweeter impedance selector: 4-Ohm or 8-Ohm Tweeter attenuation selector: 0dB, -3dB, -6dB Mounting hardware: Included Sold as: Individual unit (not a pair) Dimensions: Not specified — confirm with Rockford Fosgate Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 3kHz 6dB/Octave Low-Pass Filter for Woofer Outputs — The PP4-X delivers a 6dB/octave low-pass filter at 3kHz to the woofer channel outputs — limiting the frequency content sent to the Punch Pro midrange drivers to below 3kHz. This protects the midrange driver from high-frequency content above its optimal operating range and works in conjunction with the built-in 6dB/octave high-pass in the PP4-T tweeter to create a complete 2-way crossover system. Dual Woofer Outputs — Two woofer output terminals allow a single PP4-X to drive two Punch Pro midrange drivers from one channel — a common SPL and competition front stage configuration where two 8" midrange drivers (such as the PPS4-8) are mounted per side for increased midrange output. Selectable Tweeter Impedance — 4-Ohm or 8-Ohm — A switch selects whether the tweeter output is configured for a 4-Ohm or 8-Ohm tweeter impedance — allowing the PP4-X to accommodate different Punch Pro tweeter configurations within the same system. Selectable Tweeter Attenuation — 0dB, -3dB, -6dB — Three attenuation levels allow the tweeter output to be adjusted relative to the midrange level — compensating for the sensitivity difference between the tweeter and midrange drivers or for installation positions where the tweeter is closer to the listening position and would otherwise sound too prominent. 125W RMS / 250W Peak Power Handling — Matched to the power handling of the Punch Pro midrange driver range, the PP4-X safely handles 125W RMS — appropriate for use with the high-output amplifiers typical in SPL-oriented systems. Designed Exclusively for Punch Pro 4-Ohm Speakers — The PP4-X is not a universal passive crossover. It is engineered for the specific impedance and crossover topology of the Rockford Fosgate Punch Pro 4-Ohm speaker range — using the PP4-T tweeter's built-in 6dB/octave crossover as part of the complete system design. Using the PP4-X with non-Punch Pro or non-4-Ohm speakers will produce incorrect frequency division and impedance loading. Sold Individually — One PP4-X per purchase. For a stereo front stage installation, two PP4-X units are required — one per channel. Technical Specs Specification Detail Brand Rockford Fosgate Part Number PP4-X Series Punch Pro Part Type Passive Crossover Compatible With Rockford Fosgate Punch Pro 4-Ohm speakers only Power Handling (RMS) 125W ✓ Power Handling (Peak) 250W ✓ Woofer Impedance 4-Ohm (required) ✓ Woofer Outputs 2 (dual) ✓ Low-Pass Filter 6dB/Octave at 3kHz ✓ Tweeter HP Via built-in PP4-T crossover (not in this unit) Tweeter Impedance Select 4-Ohm / 8-Ohm ✓ Tweeter Attenuation 0dB / -3dB / -6dB ✓ Mounting Hardware Included ✓ Sold As Individual Unit (not a pair) ✓ Dimensions Not specified — confirm with Rockford Fosgate Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Designed exclusively for: Rockford Fosgate Punch Pro 4-Ohm midrange drivers (e.g. PPS4-8) Rockford Fosgate Punch Pro 4-Ohm tweeters with built-in 6dB/octave HP (e.g. PP4-T) Pairs with: Rockford Fosgate PP4-T Punch Pro 1.5" tweeter (provides the HP crossover side) Rockford Fosgate PPS4-8 Punch Pro 8" midrange/midbass (one or two per woofer output) High-output amplifiers for SPL front stage use Frequently Asked Questions What does the PP4-X do and what does it not do? The PP4-X provides the low-pass (woofer) side of a 2-way passive crossover system — filtering frequencies above 3kHz away from the midrange driver outputs. It does not provide a high-pass filter for the tweeter; the tweeter's high-pass filter is built into the Punch Pro tweeter unit. Both crossovers must be used together for the complete system to operate correctly. Can I use the PP4-X with non-Rockford Fosgate speakers? No. The PP4-X is specifically engineered for the Punch Pro 4-Ohm speaker topology and relies on the built-in crossover in the Punch Pro tweeter for the tweeter channel. It will not function correctly with other brand speakers or other Rockford Fosgate series. What is the low-pass crossover frequency? 3kHz — confirmed. The PP4-X provides a 6dB/octave low-pass filter at 3kHz for the woofer outputs. Above 3kHz, the output to the midrange drivers rolls off at 6dB per octave. Why are there two woofer outputs? The dual woofer outputs allow a single PP4-X to drive two Punch Pro midrange drivers from one amplifier channel — a configuration used in high-SPL front stage builds where two midrange drivers are mounted per side for increased output. Each output is rated for a 4-Ohm load — confirm the total impedance configuration with Rockford Fosgate when using both outputs simultaneously. What does the tweeter attenuation selector do? The 0dB, -3dB, and -6dB settings reduce the output level to the tweeter relative to the midrange. This compensates for sensitivity differences between the tweeter and midrange driver, and for installation positions where the tweeter is closer to the listening position and would otherwise produce more prominent treble than intended. Set the attenuation level during system setup based on listening tests. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

6" 2-Way Punch Component System 60W RMS, FlexFit Basket, PEI Dome Tweeter with ICC, Grilles Included. Product Overview The Rockford Fosgate Punch P16-S is a 6" 2-way component speaker system rated at 60W RMS the 6" step up from the P152-S (5.25"), sharing the same Punch component platform: FlexFit basket, PEI dome tweeter with Integrated Concealed Crossover (ICC), injection-moulded mineral-filled polypropylene cone, and butyl rubber surround. The kit includes two woofers with grilles, two tweeters, integrated crossovers, and mounting hardware. The 6" woofer provides a larger cone area than the 5.25" P152-S delivering improved low-frequency extension and output while maintaining the same dedicated component configuration for independent tweeter placement. Technical specifications sensitivity, frequency response, mounting depths, and crossover details are not confirmed in the supplier data for the P16-S. Pull the official Rockford Fosgate P16-S datasheet before publishing, using the P152-S spec set as a reference for the data fields needed. Key Specifications Woofer size: 6 inch Configuration: 2-way component system Power handling (RMS): 60W per woofer (confirmed) Peak power: Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Woofer mounting depth: Not specified — confirm with Rockford Fosgate Tweeter size: Implied 1" (25mm) from description — confirm with Rockford Fosgate Tweeter mounting depth: Not specified — confirm with Rockford Fosgate Tweeter dome material: PEI (features) Crossover type: ICC (Integrated Concealed Crossover) Crossover point: Not specified — confirm with Rockford Fosgate Recessed tweeter mount: 1-3/4" hole saw Cone: Injection-moulded mineral-filled polypropylene Surround: Butyl rubber Basket: FlexFit OEM adapter plate: Not mentioned in features — confirm with Rockford Fosgate Grilles: Included (confirmed — "two woofers with grilles") Mounting hardware: Included Kit contents: 2 woofers + 2 tweeters + crossovers + grilles + hardware CEA-2031 compliant: Not stated — confirm with Rockford Fosgate Impedance: Not specified — confirm with Rockford Fosgate Shipping weight: Not specified — confirm with Rockford Fosgate Cutout diameter: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 6" Woofer — More Bass Extension Than 5.25" — The larger 6" cone moves more air than the P152-S's 5.25" woofer, typically delivering improved low-frequency output and extension in the same door position. 60W RMS — 10W More Than P152-S — At 60W RMS, the P16-S handles 10W more than the P152-S (50W) — consistent with the larger 6" driver's capacity for sustained power input. PEI Dome Tweeter with ICC — Consistent with the P152-S — PEI dome, Integrated Concealed Crossover within the tweeter assembly, recessed mount via standard 1-3/4" hole saw. See Red-flag #1 on the "soft dome" vs PEI material conflict. FlexFit Basket — Non-standard basket geometry for OEM cavity compatibility across a range of factory door speaker positions. Mineral-Filled Polypropylene Cone, Butyl Rubber Surround — Same construction as P152-S and P16 — stiffened cone, durable butyl surround for Australian conditions. Grilles and Hardware Included — Two woofer grilles and all mounting hardware in the kit. Technical Specs Specification Detail Brand Rockford Fosgate Part Number P16-S Series Punch Woofer Size 6 inch Configuration 2-Way Component Power Handling (RMS) 60W per woofer ✓ Peak Power Not specified — confirm with Rockford Fosgate Sensitivity Not specified — confirm with Rockford Fosgate Frequency Response Not specified — confirm with Rockford Fosgate Woofer Mounting Depth Not specified — confirm with Rockford Fosgate Tweeter Size Implied 1" — confirm with Rockford Fosgate Tweeter Mounting Depth Not specified — confirm with Rockford Fosgate Tweeter Dome Material PEI Crossover ICC (Integrated Concealed) Crossover Point Not specified — confirm with Rockford Fosgate Recessed Tweeter Mount 1-3/4" hole saw ✓ Cone Injection-Moulded Mineral-Filled Polypropylene Surround Butyl Rubber Basket FlexFit OEM Adapter Plate Not mentioned — confirm with Rockford Fosgate Grilles Included ✓ Mounting Hardware Included ✓ Kit Contents 2 woofers + 2 tweeters + crossovers + grilles + hardware CEA-2031 Compliant Not confirmed Impedance Not specified — confirm with Rockford Fosgate Cutout Diameter Not specified — confirm with Rockford Fosgate Shipping Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable installation: 6" front door speaker positions OEM factory locations with FlexFit basket compatibility Punch component system comparison: Feature P152-S (5.25") P16-S (6") RMS 50W ✓ 60W ✓ Sensitivity 87dB ✓ TBC Freq. Response 70Hz–22kHz ✓ TBC Tweeter Size 1.0" (25.4mm) ✓ Implied 1" Surround Butyl Rubber Butyl Rubber OEM Adapter Plate Yes ✓ Not confirmed CEA-2031 Yes ✓ TBC Pairs well with: Rockford Fosgate T400-4, T600-4, or T1000-4AD 4-channel amplifiers Dedicated subwoofer for bass below the 6" woofer's confirmed lower frequency limit (TBC) Frequently Asked Questions How does the P16-S differ from the P152-S? Both are Punch series 2-way component systems with identical platform construction. The P16-S uses a 6" woofer versus the P152-S's 5.25", and is rated at 60W RMS versus 50W. The 6" cone provides improved low-frequency extension and output. Select based on which woofer size fits your vehicle's front door speaker positions. What tweeter dome material is used in the P16-S? The supplier description states "1" soft dome tweeters" while the features list confirms "PEI dome tweeter." PEI is a rigid thermoplastic — not a soft dome material. This conflict exists in the supplier data for both the P16-S and P152-S. Confirm the correct material with Rockford Fosgate before purchasing if tweeter character is a specific consideration. Is the OEM adapter plate included in the P16-S kit? The P152-S explicitly includes an OEM adapter plate. The P16-S features list does not mention one — this may be an omission or a genuine difference between the two models. Confirm with Rockford Fosgate before purchasing. What crossover does the P16-S use? An ICC (Integrated Concealed Crossover) — the crossover is built into the tweeter assembly, eliminating the need for a separate crossover box. Crossover point and slope are not confirmed for the P16-S — pull from the official Rockford Fosgate P16-S datasheet. The P152-S crossover (3.5kHz @ 12dB/octave Butterworth) may be similar but should not be assumed. Are grilles included with the P16-S? Yes — the product description confirms the kit includes two woofers with grilles alongside the tweeters and hardware. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Ultra-Compact 400W 4-Channel Amplifier Class-AD, Constant Power, C.L.E.A.N. Clip Detection, and a 2/4-Channel Input Switch for Flexible Integration. Product Overview The Rockford Fosgate Power T400X4AD is a 400W 4-channel amplifier built on the same Class-AD platform as the T400X2AD delivering high efficiency in an ultra-compact chassis purpose-built for hybrid and electric vehicles, small cars, motorcycles, and side-by-side UTVs. While the T400X2AD handles two channels, the T400X4AD extends this to four channels, making it the appropriate choice when all four speaker positions (front left, front right, rear left, rear right) need amplification from a single compact unit. A 2/4-channel input switch is a key addition over the 2-channel model allowing the amplifier to accept either a full 4-channel input from four RCA connections or a 2-channel input that is internally split to drive all four output channels. This simplifies integration with headunits that offer only a 2-channel RCA output while still delivering amplification across all four speaker positions. High-level inputs with auto turn-on, Remote-Out, C.L.E.A.N. clip detection, top-mounted controls, dual fan cooling, and 4Ω bridged capability complete the feature set shared with the T400X2AD. Key Specifications Power output: 400W total (4-channel — rated power per channel at specific impedance not confirmed — see Red-flags) Amplifier class: Class-AD (Rockford Fosgate proprietary) Configuration: 4-channel Constant Power: Yes — same output at 4Ω and 2Ω (multi-impedance) 2/4 channel input switch: Yes Bridged operation: Yes — 4Ω bridged capable High-level inputs: Yes — with auto turn-on Low-level inputs: Yes (RCA) Remote-Out: Yes — when using high-level inputs C.L.E.A.N. input/output clip detection: Yes — with LED indicators Crossover: Built-in (type/slope not specified — confirm with Rockford Fosgate) Cooling: Dual fan forced induction + dual extruded heat sinks + real-time thermal sensing Controls: Top mounted Power/ground connectors: 8 AWG RCA connectors: Upgraded 3-stage thermal lock extrusion: Yes Discrete surface mount technology: Yes Signal-to-noise ratio: Not specified — confirm with Rockford Fosgate THD: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Dimensions: Not specified — confirm with Rockford Fosgate Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 4-Channel Output for Full Speaker Coverage — Amplifies all four speaker channels (front and rear left/right) from a single compact unit — providing a full-vehicle speaker upgrade without requiring a second amplifier or a larger chassis. 2/4 Channel Input Switch — A key practical addition over the T400X2AD. In 2-channel mode, a single stereo RCA input is split internally to drive all four output channels — ideal for head units that offer only a 2-channel preamp output or systems where running four RCA cables is impractical. In 4-channel mode, discrete stereo front and rear inputs allow independent level control across the front and rear channels. Class-AD Technology — Ultra-Compact High Efficiency — The same Class-AD topology as the T400X2AD, delivering high efficiency in a compact chassis suited to hybrid vehicles, electric vehicles, UTVs, motorcycles, and small cars where a conventional full-size 4-channel amplifier will not fit. Constant Power at 4Ω and 2Ω — Maintains the same output wattage at both 4Ω and 2Ω speaker loads — consistent amplifier performance regardless of whether 4Ω or 2Ω speakers are fitted across the four channels. High-Level Inputs with Auto Turn-On — Connects directly to factory head unit speaker outputs without a remote turn-on wire — essential for modern OEM systems, hybrid and electric vehicles, and any installation where a conventional RCA and remote output is unavailable. Remote-Out via High-Level Input — When activated by high-level auto turn-on, the Remote-Out provides a 12V trigger for downstream accessories — enabling a subwoofer amplifier or other accessories to be activated in parallel without a remote wire from the head unit. C.L.E.A.N. Input/Output Clip Detection with LEDs — Monitors both input and output stages for clipping during gain setup, with separate LED indicators for each stage. Removes the guesswork from gain setting — the single most important step for maximising sound quality and protecting speakers and the amplifier. Top Mounted Controls — Gain, crossover, and C.L.E.A.N. indicators are all accessed from the top of the amplifier, making adjustments and visual checks possible without removing the unit from its mounting position. Dual Fan Forced Induction Cooling — Active cooling manages heat in confined mounting spaces common to compact vehicle and UTV installations where passive cooling alone is insufficient. Dual Extruded Heat Sinks with Real-Time Thermal Sensing — Passive and active thermal management in combination — the 3-stage thermal lock extrusion provides staged protection against sustained overload. 4Ω Bridged Capable — Any pair of channels can be bridged to deliver higher output to a single 4Ω load — adding subwoofer drive or high-power speaker capability to the 4-channel configuration. Technical Specs Specification Detail Brand Rockford Fosgate Part Number T400X4AD Series Power Power Output 400W (4-channel total) Amplifier Class Class-AD (Rockford Fosgate proprietary) Configuration 4-Channel Constant Power Yes — same output at 4Ω and 2Ω 2/4 Channel Input Switch Yes Bridged Operation Yes — 4Ω bridged capable High-Level Inputs Yes — with auto turn-on Low-Level Inputs Yes (RCA) Remote-Out Yes (when using high-level inputs) C.L.E.A.N. Clip Detection Input and output — with LED indicators Crossover Built-in — type/slope not specified Cooling Dual fan + dual extruded heat sinks + real-time thermal sensing Controls Top Mounted Power/Ground Connectors 8 AWG RCA Connectors Upgraded Construction Discrete Surface Mount Technology Rated Power per Channel Not specified — confirm with Rockford Fosgate Frequency Response Not specified Signal-to-Noise Ratio Not specified THD Not specified Dimensions Not specified Weight Not specified Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable vehicle applications: Hybrid and electric vehicles Small cars and hatchbacks with limited amplifier mounting space Motorcycles and touring bikes Side-by-side UTVs (Polaris RZR, Can-Am Maverick, and similar) Trucks and SUVs requiring a compact 4-channel solution OEM system upgrades where factory head unit high-level outputs are the only available signal source Suitable speaker configurations: Full 4-channel speaker system (front and rear — 4Ω or 2Ω) 2-channel input driving all four outputs via 2/4 channel switch Bridged pairs for higher-output 2-channel or mono applications T400X2AD vs T400X4AD — choosing between them: T400X2AD (2-channel): Front speakers only, or a single stereo zone — simplest integration, PLC2 remote ready T400X4AD (4-channel): Front and rear speakers from a single unit — adds 2/4 channel input switch for flexible headunit integration Pairs well with: Aftermarket door speakers across all four positions (4Ω or 2Ω) A dedicated mono subwoofer amplifier triggered via Remote-Out 8 AWG amplifier wiring kits Rockford Fosgate or aftermarket 4-channel RCA cables Frequently Asked Questions What does the 2/4 channel input switch do? In 2-channel mode, a single stereo (2-channel) RCA input is internally distributed to drive all four amplifier output channels — useful when the head unit has only a 2-channel preamp output. In 4-channel mode, discrete front and rear stereo inputs are used, allowing independent front/rear level control. This makes the T400X4AD compatible with a wider range of head units without requiring additional signal processing. How does the T400X4AD differ from the T400X2AD? Both amplifiers share the same Class-AD platform, feature set, and wattage. The T400X4AD provides four output channels versus two, and adds a 2/4 channel input switch. The T400X2AD includes PLC2 remote compatibility — confirm whether the T400X4AD supports PLC2 remote operation with Rockford Fosgate if this is a requirement. How does the high-level auto turn-on work with a factory system? The high-level inputs accept signal from factory head unit speaker outputs and activate the amplifier automatically when audio signal is present — no remote turn-on wire is required. The Remote-Out then provides a 12V trigger for a downstream subwoofer amplifier or other accessories. What does C.L.E.A.N. clip detection help with during installation? C.L.E.A.N. (Circuit Level Evaluation And Normalisation) monitors both the input and output stages for clipping, with LED indicators for each. During gain setup, the LEDs identify when the signal clips — allowing the gain to be set at the maximum clean level. Correct gain structure is the most effective way to protect speakers from distortion damage and maximise sound quality. Can the T400X4AD be used in a bridged configuration? Yes. Pairs of channels can be bridged to deliver higher output to a single 4Ω load — for example, bridging channels 1 and 2 for a front subwoofer or a single high-output speaker, while channels 3 and 4 continue to drive rear speakers in standard stereo configuration. Confirm the bridged power output at 4Ω with the official Rockford Fosgate datasheet. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

100 Watts × 4 Channels at 2Ω Compact 4-Channel Amplifier for Front/Rear Systems and Front Stage with Rear Subwoofer. Product Overview The Rockford Fosgate Power T400-4 is a 4-channel amplifier delivering 100W into each of its four channels at 2Ω confirmed by Rockford Fosgate making it suitable for a full 4-way front and rear speaker system or a front stage and rear subwoofer configuration. The compact chassis with Dynamic Thermal Management is specifically designed for under-seat or space-constrained installation locations that full-size 4-channel amplifiers cannot accommodate. Unlike the Class-AD T400X4AD which prioritises ultra-compactness for hybrid vehicles and UTVs the T400-4 is a full-featured conventional design with a MOSFET power supply and output stage, 4-gauge power and ground connectors, a 24dB/octave crossover, and a 2/4 channel input switch for flexible headunit integration. It is the choice when confirmed 100W per channel at 2Ω output is the primary specification requirement, and when the installation allows 4-gauge wiring for maximum power delivery. Key Specifications Power output: 100W × 4 channels @ 2Ω (confirmed) Power output @ 4Ω: Not specified Bridged output: Not specified Configuration: 4-channel MOSFET power supply: Yes MOSFET output stage: Yes Crossover: 24dB/octave 2/4 channel input switch: Yes Power/ground connectors: 4 gauge Speaker connections: Audiophile grade Thermal management: Dynamic Thermal Management Chassis: Compact — under-seat installation capable Amplifier class: Not specified Signal-to-noise ratio: Not specified THD: Not specified Frequency response: Not specified Dimensions: Not specified Weight: Not specified Warranty: Not specified  Features & Benefits 100W × 4 Channels at 2Ω — Confirmed Power Specification — Unlike many amplifier listings where per-channel power at a specific impedance is absent, Rockford Fosgate confirms 100W per channel into 2Ω on the T400-4. This gives the system designer a concrete figure to work with when matching the amplifier to 2Ω speaker loads. Power at 4Ω and bridged mono output should be confirmed from the official Rockford Fosgate datasheet. Front/Rear Fading or Front Stage Plus Rear Sub Configurations — The T400-4 is designed for two typical 4-channel setups: a full 4-way front and rear full-range speaker system, or a front stage component system with rear subwoofers driven from the rear channels. The 24dB/octave crossover and 2/4 channel input switch support both configurations without external signal processing. Dynamic Thermal Management for Compact Installation — Rather than a fixed protection shutdown at a temperature threshold, Dynamic Thermal Management actively manages the amplifier's output in response to temperature — reducing output as needed to prevent overheating in confined spaces. This allows the T400-4 to be installed under front seats, in centre consoles, or in other space-constrained locations where heat dissipation is limited. MOSFET Power Supply and Output Stage — MOSFET-based design in both the power supply and output stage provides clean, efficient power delivery and responsive switching — the same proven technology used across the Rockford Fosgate Power series. 24dB/Octave Crossover — Steep crossover slope for precise frequency band separation — enabling high-pass filtering on front stage speakers and low-pass filtering on rear subwoofers, or full-range pass-through for a standard 4-way system. 2/4 Channel Input Switch — In 2-channel mode, a stereo input is internally distributed to all four output channels — allowing connection to head units with only a 2-channel RCA preamp output. In 4-channel mode, discrete front and rear RCA inputs allow independent level control. 4 Gauge Power and Ground Connectors — Appropriate wiring infrastructure for a 400W 4-channel amplifier, ensuring the power delivery path matches the amplifier's output capability. Audiophile Grade Speaker Connections — High-quality output terminals for a solid, low-resistance connection to speaker voice coils across all four channels. Technical Specs Specification Detail Brand Rockford Fosgate Part Number T400-4 Series Power Configuration 4-Channel Power Output @ 2Ω 100W × 4 channels ✓ Power Output @ 4Ω Not specified Bridged Output Not specified Amplifier Class Not specified MOSFET Power Supply Yes MOSFET Output Stage Yes Crossover 24dB/Octave 2/4 Channel Input Switch Yes Power/Ground Connectors 4 Gauge Speaker Connections Audiophile Grade Thermal Management Dynamic Thermal Management Chassis Compact — Under-Seat Capable Signal-to-Noise Ratio Not specified THD Not specified Frequency Response Not specified Dimensions Not specified Weight Not specified Warranty Not specified Compatible With / Goes Well With Suitable system configurations: Full 4-way front and rear speaker system (full-range crossover setting) Front stage component speakers (high-pass) + rear subwoofers (low-pass via crossover) Under-seat, centre console, or space-constrained installations where Dynamic Thermal Management allows reliable operation Comparing T400-4 vs T400X4AD: T400-4: Confirmed 100W×4 @ 2Ω, 4-gauge wiring, Dynamic Thermal Management, conventional design — suited to standard car audio builds with 4-gauge wiring infrastructure T400X4AD (Class-AD): Ultra-compact, 8 AWG wiring, high-level auto turn-on, C.L.E.A.N. clip detection, PLC2 remote — suited to hybrid/EV, UTV, motorcycle, and OEM integration builds Pairs well with: Rockford Fosgate or aftermarket component front speakers (4Ω or 2Ω) Rear subwoofers or coaxial speakers for the rear channels 4-gauge amplifier wiring kits Rockford Fosgate or aftermarket 4-channel RCA cables Frequently Asked Questions What is the confirmed power output of the T400-4? Rockford Fosgate confirms 100W per channel into 2Ω, for a total of 400W across four channels. Power output at 4Ω and the bridged mono output rating are not confirmed in the supplier data — pull the official T400-4 datasheet for the full power specification table. What does Dynamic Thermal Management mean for installation flexibility? Dynamic Thermal Management actively reduces amplifier output as temperature rises — rather than a hard shutdown — allowing the T400-4 to sustain operation in confined spaces like under front seats where heat dissipation is limited. The amplifier trades peak output for continuous operation in hot or restricted environments. What is the difference between the T400-4 and the T400X4AD? Both are Rockford Fosgate Power series 400W 4-channel amplifiers. The T400-4 is a conventional design with confirmed 100W×4 @ 2Ω, 4-gauge connectors, and Dynamic Thermal Management. The T400X4AD is the Class-AD ultra-compact variant with 8 AWG connectors, high-level auto turn-on, C.L.E.A.N. clip detection, and specific design for hybrid vehicles, UTVs, and motorcycles. The right choice depends on your installation environment and integration requirements. Can the T400-4 run both front speakers and rear subwoofers simultaneously? Yes. This is one of the T400-4's designed use cases — front channels in high-pass mode driving component speakers, rear channels in low-pass mode driving subwoofers. The built-in 24dB/octave crossover provides the frequency separation required for this configuration without external processing. What gauge wiring does the T400-4 require? The T400-4 uses 4-gauge power and ground connectors. A minimum of 4-gauge cable is recommended for the power and ground runs. Confirm the specific cable length and fuse requirements for your installation with Rockford Fosgate's wiring guide or your installer. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate P600X4 600 Watts, Four Channels, Built for Any System You Throw at It Product Overview The Rockford Fosgate P600X4 is a Punch Series 4-channel amplifier rated at 150 watts RMS per channel at 2 ohms 600 watts total engineered to adapt to virtually any car audio system layout. Run it in full 4-channel stereo for front and rear speakers, bridge both channel pairs into a high-power 2-channel configuration, or operate it in 3-channel mode with stereo speakers up front and a subwoofer on the bridged rear channels. The P600X4 handles all three without compromise. What sets the P600X4 apart from entry-level 4-channel options is its expanded feature set. RCA pass-thru outputs let you chain additional amplifiers as your system grows without resorting to Y-adapters that degrade signal quality. The optional PLC2 remote Punch Level Control adds a dash-mounted bass adjustment knob with a real-time clip indicator, and the variable HP/LP Butterworth crossover gives you precise per-channel tuning for speakers and subwoofers alike. For Australian builds dealing with heat, corrugations, and long-distance touring, the cast aluminium heatsink and onboard protection circuits keep everything running cleanly. Key Specifications Total RMS Output: 600 watts Per-Channel Output: 150W x 4 at 2 ohms Channels: 4 (stereo, 3-channel, or bridged 2-channel) Bridgeable: Yes — bridge both channel pairs for high-power 2-channel operation Crossover: Variable HP/LP, 12dB/octave Butterworth Onboard EQ: Punch EQ — +18dB boost at 45Hz Inputs: High-level (speaker-level) and RCA RCA Pass-Thru Outputs: Yes Auto Turn-On: Yes — via high-level input detection Remote Control: Optional PLC2 Punch Level Control (with input clip indicator) Turn-On Behaviour: Muted (no thump on startup) Heatsink: Cast aluminium Control Panel Position: Stealth top-mounted Protection: Short circuit and over-current Features & Benefits High-Level Input with Auto Turn-On — Connects directly to factory head unit speaker outputs with no RCA cables required. The Auto Turn-On circuit fires the amp when it detects a signal, eliminating the need for a dedicated remote turn-on wire. Ideal for OEM upgrades across any vehicle. RCA Pass-Thru Outputs — Extend your system by daisy-chaining a subwoofer amplifier or additional channels without Y-adapters. Keeps signal integrity intact and your wiring clean as your build evolves. C.L.E.A.N. Setup (Clip Level Elimination Audio Notify) — Rockford Fosgate's onboard gain-calibration system takes the guesswork out of setup. Dial in maximum clean output without a multimeter or test tone — useful for installers and enthusiasts alike. Optional PLC2 Remote Punch Level Control — Adds a dash-mountable knob for real-time bass level adjustment. The input clip indicator lights up before distortion sets in — live feedback that protects your speakers and keeps your tune dialled in on the road. Variable HP/LP 12dB/Octave Butterworth Crossover — Independently configure each channel pair for high-pass (speakers) or low-pass (subwoofers) operation. The variable crossover point gives you precision tuning without an external processor. Onboard Punch EQ (+18dB @ 45Hz) — Adds controlled sub-bass punch directly from the amp. No separate bass EQ or processor required for most builds — tune to taste from the top-mounted control panel. 3-Channel Operating Mode — Run full-range or component speakers on the front two channels and bridge the rear pair for a subwoofer — one amp, complete system. Particularly useful in utes and wagons where boot space is at a premium. Muted Turn-On — No startup thump, no tweeter stress, no giveaway of a poorly executed install. Keeps your system sounding professional from the moment the ignition fires. Stealth Top-Mounted Control Panel — All gain, crossover, and EQ controls are accessible on the top face of the amp for easy tuning during setup, without cluttering the amp's profile once mounted. Cast Aluminium Heatsink — Handles extended thermal loads during long listening sessions. In Australian conditions — outback runs, summer road trips, confined boot spaces — heat management is a real-world spec that matters. Short Circuit & Over-Current Protection — Onboard protection circuits guard the amplifier and your speakers against wiring faults and impedance mismatches. Technical Specs Specification Detail Total RMS Power 600W Per-Channel RMS (2Ω) 150W x 4 Number of Channels 4 Operating Modes 4-channel stereo, 3-channel, bridged 2-channel Bridgeable Yes (both channel pairs) Crossover Type Variable HP/LP Butterworth Crossover Slope 12dB/octave Onboard EQ +18dB boost at 45Hz Input Type High-level (speaker-level) + RCA RCA Pass-Thru Yes Auto Turn-On Yes (via high-level input) Remote Punch Level Control Optional (PLC2, sold separately) Input Clip Indicator Yes (via PLC2) Turn-On Mode Muted Heatsink Material Cast aluminium Control Panel Location Top-mounted (stealth) Short Circuit Protection Yes Over-Current Protection Yes Dimensions Not specified Signal-to-Noise Ratio Not specified THD Not specified Frequency Response Not specified Input Sensitivity Not specified Compatible With / Goes Well With System Configurations: 4-way full-range speaker system (front + rear, 4-channel stereo) 3-channel mode — stereo component speakers (front) + bridged subwoofer (rear) Bridged 2-channel mode — high-power output for two subwoofers or speaker pairs Front-stage only (component speakers, 2 channels active) Head Unit Compatibility: Factory/OEM head units (via high-level input with Auto Turn-On) Aftermarket head units with RCA pre-outs Accessories: Rockford Fosgate PLC2 Remote Punch Level Control (optional, sold separately) Recommended: use manufacturer-specified power and speaker cables to optimise power delivery (cable spec not provided — confirm with supplier) Frequently Asked Questions Can the P600X4 run speakers and a subwoofer at the same time? Yes. In 3-channel mode, the front two channels power stereo speakers while the rear channels are bridged to drive a subwoofer — a complete system from a single amplifier. What is the RCA pass-thru and why does it matter? The RCA pass-thru outputs let you connect an additional amplifier downstream — such as a dedicated subwoofer amp — without using signal-splitting Y-adapters, preserving audio quality as your system grows. Does the P600X4 work with a factory head unit? Yes. The high-level input accepts speaker-level signals from any OEM head unit, and the Auto Turn-On circuit activates the amplifier automatically — no remote turn-on wire required. Is the PLC2 remote punch level control included in the box? No. The PLC2 is an optional accessory sold separately. It adds a dash-mountable remote bass control knob and a real-time input clip indicator to help you tune on the go without touching the amp. What does C.L.E.A.N. setup mean and do I need extra tools? C.L.E.A.N. (Clip Level Elimination Audio Notify) is Rockford Fosgate's built-in gain-setting system. No multimeter or external tools are needed — it guides you to the optimal gain level to maximise output while keeping distortion out of your signal chain. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Two channels. BRT efficiency. Built for motorcycles, ATVs, and stealth installs. Product Overview The Rockford Fosgate PBR300X2 is a 2-channel amplifier from the Punch series, delivering 300W total using Rockford Fosgate's patented BRT (Boosted Rail Technology). Unlike conventional 2-channel amplifiers that rely on a switching power supply to generate their output, BRT achieves rated power through an ultra-efficient design that eliminates the switching stage entirely resulting in a chassis significantly smaller than a traditional amplifier of equivalent output. Total power is 300W across two channels; power per channel and impedance breakdown are not specified in supplier-provided data. The PBR300X2 is positioned for installations where space and electrical draw are primary constraints. Motorcycles requiring stereo speaker output, ATVs, and recreational vehicles with limited mounting real estate are the target use cases along with stealth car and marine builds where a standard amplifier chassis simply won't fit. The variable 4–6V hi-level DC offset turn-on circuit allows direct integration with OEM speaker outputs in systems that don't provide a dedicated remote turn-on wire, while high-level inputs eliminate the need for an aftermarket head unit or RCA outputs. A 12dB/octave Butterworth crossover and MOSFET output stage complete a practical, installation-friendly feature set. Key Specifications Channels: 2 Total output power: 300W (power per channel and impedance breakdown — not specified) Power supply technology: BRT (Boosted Rail Technology — no switching power supply) Output stage: MOSFET Crossover: 12dB/octave Butterworth (frequency range — not specified) Signal input: High level Turn-on method: Variable hi-level DC offset (4–6V) Chassis: Ultra-compact Bridgeable: Not specified Frequency response: Not specified Input sensitivity: Not specified Nominal impedance: Not specified CEA compliance: Not specified in provided data Power wire gauge: Not specified Speaker wire gauge: Not specified Operating voltage: Not specified Recommended fuse: Not specified Dimensions: Not specified Features & Benefits BRT (Boosted Rail Technology) — No Switching Power Supply — The PBR300X2 uses Rockford Fosgate's patented BRT architecture to produce rated power without a conventional switching power supply. This reduces current draw, minimises electrical noise, and shrinks the chassis to a fraction of the size of a traditional 2-channel amplifier — making it viable for vehicle types and install locations that would otherwise rule out amplification entirely. Ultra-Compact Chassis — Stereo Power in a Stealth Footprint — Where the PBR300X1 delivers mono output for a single driver, the PBR300X2 provides two independent channels from the same compact BRT platform. This makes it the logical choice for motorcycle stereo builds — left and right speaker channels from a single unit that installs in a saddlebag, underseat compartment, or within a fairing. Exact dimensions are not specified in supplier data — confirm with Rockford Fosgate before planning a space-critical install. Variable Hi-Level DC Offset Turn-On (4–6V) — Motorcycles, ATVs, and many OEM car audio systems either lack a dedicated remote turn-on output or carry a DC offset on their speaker outputs. The PBR300X2's variable DC offset circuit detects a 4–6V signal on the speaker inputs and uses it to power the amplifier — removing the need to source and run a remote wire in installations where doing so is difficult or impossible. High-Level Inputs — Accepts signal directly from the speaker outputs of a factory head unit, OEM radio, or handlebar-mounted controller. No line output converter or aftermarket head unit is required, keeping the installation simple and the component count low — particularly relevant for motorcycle and recreational vehicle builds where simplicity and reliability matter. MOSFET Output Stage — The MOSFET output stage contributes to the compact, efficient character of the PBR300X2 and handles the variable voltage and vibration conditions common in motorcycle and off-road vehicle environments more reliably than earlier output stage designs. It also supports the BRT architecture's low-heat operating profile. 12dB/Octave Butterworth Crossover — The on-board Butterworth crossover allows the two output channels to be filtered, directing appropriate frequency ranges to different speakers in a system. The crossover frequency range is not specified in supplier data — confirm with Rockford Fosgate before planning a multi-speaker install. Technical Specs Specification Detail Channels 2 Total output power 300W Power per channel Not specified Power by impedance Not specified Power supply BRT — no switching power supply Output stage MOSFET Circuit topology Not specified Frequency response Not specified Input sensitivity Not specified THD+Noise Not specified Nominal impedance Not specified Bridgeable Not specified Crossover type 12dB/octave Butterworth Crossover frequency range Not specified Signal input High level Turn-on method Variable hi-level DC offset, 4–6V CEA compliance Not specified Power wire gauge Not specified Speaker wire gauge Not specified Operating voltage Not specified Recommended fuse Not specified Dimensions Not specified Weight 4.3 kg Compatible With / Goes Well With The PBR300X2 is confirmed by the manufacturer for use in the following applications: Motorcycles requiring 2-channel (stereo) speaker amplification ATVs and off-road recreational vehicles Smaller stealth car, marine, or custom installations with limited space OEM/factory audio systems (via variable hi-level DC offset turn-on) Goes well with: Compact 2-channel speakers suited to motorcycle, ATV, or stealth car audio builds Factory head units and OEM audio systems (high-level input compatible) Marine or weatherproof speaker enclosures for recreational vehicle applications Frequently Asked Questions What is BRT (Boosted Rail Technology) and why does it matter for a 2-channel amp? BRT is Rockford Fosgate's patented amplifier architecture that generates rated power without a switching power supply. The result is a significantly smaller and more efficient chassis than a conventional 2-channel amplifier — making stereo amplification viable in motorcycles, ATVs, and stealth builds where space and current draw are limited. How much power does each channel produce? Total power is 300W across both channels. The per-channel power rating and impedance breakdown are not specified in supplier-provided data. Contact Rockford Fosgate or your authorised dealer to confirm per-channel output before matching to speakers. Will the PBR300X2 work on a motorcycle or ATV? Yes. The PBR300X2 is specifically designed for motorcycles, ATVs, and recreational vehicles. The BRT architecture's low current draw and ultra-compact chassis make it practical for these applications, and the variable DC offset turn-on circuit supports OEM systems that lack a standard remote turn-on output. What is the variable DC offset turn-on circuit? Many motorcycle and OEM systems output a 4–6V DC offset on their speaker lines rather than a dedicated remote turn-on signal. The PBR300X2 detects this voltage and uses it to power the amplifier automatically — eliminating the need to wire a separate remote turn-on lead in most factory and recreational vehicle installations. Can the PBR300X2 be used in a standard car or truck installation? Yes, though it is engineered primarily for space-constrained and stealth applications. It suits any car or truck installation where a compact chassis, low current draw, and factory head unit compatibility are priorities. Standard amplifier features such as RCA inputs, Punch EQ, and remote level control are not confirmed in supplier data — verify the full feature set with Rockford Fosgate if these are required. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

The 4 Channel Car Amplifier From Orion Have Been Designed to Be a True Worldwide Orion's new Cobalt amplifiers are here to change the complete vision of the car audio market. Offering more power, more quality and a more bang for your buck than any of their close competitors. Quality, power and pricing all come together with Cobalt to create the most efficient amplifier dollar per watt that the industry has ever seen, delivering the power that has always characterised and defined Orion Car Audio. Legendary Products & Support From Authorized Dealers When you choose Orion, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & Training Only authorized Orion dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty Protection: We offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don't be misled by unauthorized sellers who can't provide genuine warranty support. ▸ Reliable Customer Support: If you ever run into an issue, you're backed by Orion's official manufacturer's warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your Investment: Buying from an authorized dealer ensures you're getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few dollars worth losing all that? Choose wisely. Buy from an authorized Orion dealer today!

Read more less