Rockford Fosgate R2-500X4 Prime 500 Watt 4-Channel Full-Range Class-D Car Amplifier A 500W 4-channel Full-Range Class-D car amplifier delivering 125W x 4 at 2-ohm or 250W x 2 at 4-ohm bridged (CTA-2006 rated). Features independent front and rear channel crossover control with all-pass mode, 2/4 channel input selection switch, RCA pass-through outputs, C.L.E.A.N. gain calibration with per-channel output clip indicators, Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management. Designed and engineered in Tempe, Arizona. Backed by a 1 year warranty. Product Overview The Rockford Fosgate R2-500X4 is a 500W 4-channel Full-Range Class-D car amplifier from the Prime R2 series, purpose-built for powering car speaker pairs across the full audio spectrum. Rated continuous power is 75W x 4 at 4-ohm, 125W x 4 at 2-ohm, or 250W x 2 at 4-ohm bridged (CTA-2006, less than 1.0% THD+N). Dynamic power via PowerCube reaches 90W x 4 at 4-ohm, 160W x 4 at 2-ohm, and 300W x 2 at 4-ohm bridged. The R2-500X4 provides independent front and rear channel crossover control, each with fully adjustable high-pass and low-pass filters at 12dB/octave Butterworth (50Hz-250Hz) and an all-pass mode for full-bandwidth output. Independent front and rear variable input gain adjustment is provided. A 2/4 channel input selection switch configures the amplifier for source units with either 2 or 4 RCA outputs, working for both RCA and high-level inputs. RCA pass-through outputs allow downstream amplifier chaining - the R2-750X1 monoblock subwoofer amplifier is the natural companion for a complete car audio system. Auto-Sense turn-on activates the amplifier when a speaker-level signal is detected, with a RAP bypass switch for Retained Accessory Power systems. C.L.E.A.N. provides separate input and output clip indicators for both front and rear channel groups. Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management are all active. Cast aluminium heatsink with convection cooling. Designed and engineered in Tempe, Arizona. Features & Benefits Full-Range Class-D - Efficient 4-Channel Car Audio Amplification: Full-Range Class-D topology delivers high-efficiency power across the complete 20Hz-20kHz audio spectrum, reducing current demand on the vehicle's electrical system while powering speaker pairs with clean, accurate output. Independent Front and Rear Crossover Control with All-Pass Mode: Front and rear channels each have independent high-pass and low-pass crossover controls at 12dB/octave Butterworth (50Hz-250Hz) plus an all-pass mode for full-bandwidth output, giving more flexibility than a single shared crossover. 2/4 Channel Input Selection Switch: The input selection switch configures the R2-500X4 to accept either a 2-channel or 4-channel RCA or high-level input, working with source units that have limited RCA output pairs without requiring Y-cables or signal splitting. Bridgeable to 2-Channel - 250W Mono per Pair: The R2-500X4 can be bridged to 2-channel, delivering 250W x 2 at 4-ohm (300W dynamic), suited to driving higher-power speaker pairs or running a compact 2-channel installation. RCA Pass-Through Outputs for Downstream Chaining: RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a downstream subwoofer amplifier such as the R2-750X1 without signal degradation. C.L.E.A.N. Technology - Independent Per-Channel Clip Monitoring: C.L.E.A.N. provides separate input and output clip indicator LEDs for both the front and rear channel groups, enabling accurate independent gain calibration across all four channels. Auto-Sense Turn-On with RAP Bypass: Auto-Sense activates the amplifier automatically when a high-level input signal is detected, removing the need for a dedicated remote turn-on wire. A bypass switch is included for vehicles with Retained Accessory Power systems. Rollback Protection and NOMAD Speaker Protection: Rollback Protection dynamically manages output to prevent thermal stress during sustained high-output conditions. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. Technical Specs Specification Detail SKU R2-500X4 Number of Channels 4 Total Power 500W Rated Power - 4-ohm (CTA-2006, less than 1.0% THD+N) 75W x 4 Rated Power - 2-ohm (CTA-2006, less than 1.0% THD+N) 125W x 4 Rated Power - 4-ohm Bridged (CTA-2006) 250W x 2 Dynamic Power - 4-ohm (PowerCube) 90W x 4 Dynamic Power - 2-ohm (PowerCube) 160W x 4 Dynamic Power - 4-ohm Bridged (PowerCube) 300W x 2 Circuit Topology Full-Range Class-D Bridgeable Yes Frequency Response 20 Hz - 20 kHz THD + Noise Less than 1.0% at 4-ohm and 2-ohm Input Sensitivity Low-Level: 150mV - 4V / High-Level: 450mV - 12V Signal Input Front: 4 x RCA + 4-Pin Molex / Rear: 4 x RCA + 4-Pin Molex Input Selection 2/4 Channel Switch (RCA and High-Level) Signal Output 2 x RCA Pass-Thru (active with RCA or High-Level input) Tone Controls None Front High-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Front Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Rear High-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Rear Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth All-Pass Yes Remote Controls None Auto-Sense Turn-On Yes (with RAP bypass switch) Power Wire Gauge 4 AWG Power Input Connector Compression Terminal Block Speaker Wire Gauge 8 AWG Speaker Output Connector Compression Terminal Block Cooling Convection Heatsink Cast Aluminium Operating Voltage 9 - 16 VDC Recommended Fuse (not included) 80A Max Current Draw at 13.8V Sinewave 59A Visual Indicators Power: Blue / Protect: Red / C.L.E.A.N. In: Red / C.L.E.A.N. Out Front and Rear: Blue/Red Dimensions (H x W x D) 49 x 173 x 255mm (1.9 x 6.8 x 10.1 inch) CTA-2006 Compliant Yes Warranty 1 Year Compatible With / Goes Well With The R2-500X4 suits car audio builds requiring an efficient 4-channel full-range amplifier for speaker pairs at the Prime R2 price point. At 59A maximum current draw and an 80A fuse requirement, it places moderate demand on the vehicle's electrical system. The RCA pass-through output pairs naturally with the R2-750X1 mono subwoofer amplifier for a complete R2 series speaker and subwoofer system. Goes Well With: R2-750X1 - Companion R2 series 750W mono subwoofer amplifier, chainable via the R2-500X4's RCA pass-through outputs for a complete R2 series car audio system R2-750X5 - Alternative single-unit 5-channel R2 series amplifier for builds requiring an integrated subwoofer channel alongside speaker amplification R2-2X12 / R2-2X10 - Rockford Fosgate Prime dual loaded subwoofer enclosures when paired with the R2-750X1 companion monoblock RFK4 - Rockford Fosgate 4 AWG amplifier wiring kit to complete the installation Frequently Asked Questions What is the difference between the R2-500X4 and the R2-750X5? The R2-500X4 is a 4-channel full-range amplifier rated at 125W x 4 at 2-ohm with no dedicated subwoofer channel, no Punch EQ, and no remote level control. The R2-750X5 is a 5-channel amplifier rated at 100W x 4 plus 350W subwoofer at 2-ohm, adding a dedicated subwoofer channel with Punch EQ, infrasonic filter, RLC remote level control, and a 2/4/5 channel input switch. Choose the R2-500X4 for a pure 4-channel speaker amplifier and pair it with the R2-750X1 for subwoofer duty; choose the R2-750X5 for a single-unit 5-channel solution. Can I add a subwoofer amplifier to a system using the R2-500X4? Yes. The R2-500X4 includes RCA pass-through outputs that are active with both RCA and high-level input, allowing a distortion-free signal to be passed to a downstream mono subwoofer amplifier such as the R2-750X1. The two amplifiers chain together cleanly for a complete 4-channel speaker plus mono subwoofer car audio system. What does the 2/4 channel input selection switch do? The input selection switch configures the R2-500X4 to accept either a 2-channel or 4-channel input from the source unit, working for both RCA and high-level connections. In 2-channel mode, the single stereo RCA pair feeds all four channels internally. In 4-channel mode, separate front and rear RCA pairs are used for independent left/right front and rear channel control. What fuse does the R2-500X4 require and is it included? The R2-500X4 requires an 80A fuse, which is not included and must be sourced separately. This is smaller than the 120A fuse required by the R2-750X5 and R2-750X1, reflecting the R2-500X4's lower maximum current draw of 59A. Install the fuse as close to the battery as possible in the 4 AWG power supply line. Does the R2-500X4 need a dedicated remote turn-on wire? Not necessarily. Auto-Sense activates the amplifier automatically when a high-level speaker signal is detected at the input, removing the need for a separate remote wire in OEM integration scenarios. A RAP bypass switch is included for vehicles where the source unit continues to output a signal after the ignition is switched off.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate R2-200X2 Prime 200 Watt 2-Channel Class D Amplifier When two channels need real power without compromise, the R2-200X2 delivers 200 watts of clean, efficient Class D performance engineered by Rockford Fosgate. Product Overview The R2-200X2 is part of Rockford Fosgate's 3rd generation Prime Series, built for car audio enthusiasts who demand reliable, high-performance amplification at an accessible price. Operating as a full-range Class D 2-channel amplifier, it runs at 4 ohm or 2 ohm stereo and 4 ohm bridged/mono, giving it the flexibility to drive a front speaker pair in stereo or bridge down to a single channel to power a subwoofer. Class D topology maximises efficiency and reduces the electrical load on the vehicle's charging system, while MEHSA 4 (Maximum Efficiency Heat Sink Application) actively reduces MOSFET temperatures, lowers distortion, and prolongs output device lifespan. The top-mounted control panel keeps all adjustments within easy reach, and CTA-2006 compliant power ratings confirm that the 200W output is a real, tested figure. Designed and engineered in Tempe, Arizona, the R2-200X2 is built by fanatics, for fanatics. Features & Benefits C.L.E.A.N. Technology (Patent 8,712,066): Rockford Fosgate's patented Calibrated Level Eliminates Audible Noise circuit uses dedicated input and output clip LEDs (C.L.E.A.N. IN Red, C.L.E.A.N. OUT Blue/Red) to accurately match the source unit's output to the amplifier's input sensitivity, eliminating guesswork and reducing distortion at the source. P.O.W.E.R. Supply: Onboard power supply design that continues to generate output above the rated RMS figure as vehicle voltage increases, so real-world performance scales beyond the spec sheet across the 9-16V operating range. MEHSA 4 (Maximum Efficiency Heat Sink Application): Advanced thermal management system that reduces MOSFET operating temperatures, lowers distortion levels, increases overall durability, and extends the lifespan of output devices under sustained use. NOMAD Protection: A real-time analogue computer that continuously monitors the amplifier's outputs and protects against shorting speaker wires and dangerously low speaker impedances, providing active fault management rather than passive fusing alone. Balanced Differential Inputs: Differential input topology eliminates noise picked up by signal cables between the source unit and amplifier, delivering a cleaner signal into the amplifier stage. Fully Adjustable Butterworth Crossovers: 12 dB/octave High-Pass and Low-Pass crossovers, continuously variable from 50 to 250 Hz, with an All-Pass option for full-range output when no filtering is needed. High Level Input Capable: Accepts both low-level RCA (150mV-4V) and high-level speaker signals (450mV-12V), making integration with factory head units straightforward. Auto-Sense RAP Bypass: Auto-Sense bypass switch supports vehicles with Retained Accessory Power (RAP), allowing the amplifier to power on and off correctly using speaker-level signal detection without requiring a dedicated remote turn-on wire. RCA Pass-Through Outputs: 2-channel RCA pass-through remains active with both RCA and high-level inputs, allowing a downstream amplifier to be added without splitting cables at the head unit. CTA-2006 and CE Compliant: All power ratings verified at 14.4V with 1% or less THD to CTA-2006 industry standards, with no inflated peak figures used anywhere in the specifications. Technical Specs Specification Detail SKU R2-200X2 Series Prime Number of Channels 2 Amplifier Class Class D, Full Range Total RMS Power 200W RMS Power @ 4 Ohm 50W x 2 RMS Power @ 2 Ohm 100W x 2 Bridged Power @ 4 Ohm 200W x 1 Dynamic Power @ 4 Ohm 60W x 2 Dynamic Power @ 2 Ohm 107W x 2 Dynamic Power Bridged @ 4 Ohm 215W x 1 Bridgeable Yes Minimum Impedance (Stereo) 2 Ohm Minimum Impedance (Bridged) 4 Ohm Frequency Response 20 Hz - 20 kHz THD @ 4 Ohm <1.0% THD @ 2 Ohm <1.0% Input Sensitivity (Low-Level) 150 mV - 4V Input Sensitivity (High-Level) 450 mV - 12V Signal Input 2 x RCA low-level, 4-Pin Molex high-level Signal Output 2 x RCA pass-through (active with RCA or high-level input) Crossover High-Pass / Low-Pass: 50-250 Hz @ 12 dB/octave Butterworth All-Pass Yes Tone Controls No Remote Controls No Visual Indicators POWER (Blue), PROTECT (Red), C.L.E.A.N. IN (Red), C.L.E.A.N. OUT (Blue/Red) Operating Voltage 9-16V DC Max Current Draw (13.8V Sinewave) 18A Recommended Fuse 30A (not included) Power Wire Gauge 4 AWG Speaker Wire Gauge 8 AWG Power Input Connector Compression Terminal Block Speaker Output Connector Compression Terminal Block Cooling Convection / Heatsink (MEHSA 4) Dimensions (H x W x D) 1.9" x 6.8" x 8.1" (4.9 cm x 17.3 cm x 20.5 cm) Warranty 1 Year Compliance CTA-2006, CE Goes Well With The R2-200X2 pairs naturally with Rockford Fosgate Prime Series full-range speakers such as the R165X3, R168X2, R169X2, and R169X3 for a front stereo speaker setup. When bridged to mono at 4 ohms, it can also serve as a dedicated subwoofer channel, making it a compact single-amplifier solution for smaller builds. For systems requiring both speaker and dedicated subwoofer amplification, the R2-200X2 pairs directly with the R2-250X1 monoblock using the onboard RCA pass-through. A 4-gauge amplifier wiring kit is required for power and ground runs, and 8-gauge cable is needed for speaker outputs. Frequently Asked Questions Can the R2-200X2 power both front speakers and a subwoofer at the same time? Not simultaneously through both channels. In stereo mode, the R2-200X2 powers two speakers independently. When bridged to mono, it delivers 200 watts into a single 4-ohm load, suitable for a subwoofer, but the stereo channels are no longer available in that configuration. For a system requiring both speaker and subwoofer amplification, pairing the R2-200X2 with a dedicated monoblock such as the R2-250X1 is the recommended approach. Does the R2-200X2 require a remote turn-on wire? When using RCA inputs, a remote turn-on wire must be connected to the head unit's remote output. When using high-level speaker inputs, the Auto-Sense bypass switch can be enabled to allow the amplifier to detect an incoming signal and power on automatically, making it compatible with factory head units and systems that lack a dedicated remote output, including those with Retained Accessory Power (RAP). What does the NOMAD protection system do? NOMAD is a real-time analogue computer built into the R2-200X2 that continuously monitors the amplifier's speaker outputs. It protects the amplifier from damage caused by shorted speaker wires and dangerously low speaker impedances, providing active, dynamic protection rather than relying solely on a fuse. What gauge power, ground, and speaker wire does the R2-200X2 require? Rockford Fosgate specifies 4 AWG for power and ground runs using the onboard compression terminal block connectors. Speaker output connections require 8 AWG wire. The recommended 30A fuse is not included in the box and must be sourced separately, installed as close to the battery as possible. Can the R2-200X2 be bridged into a 2-ohm load for maximum power? No. When bridging the R2-200X2, the minimum supported impedance is 4 ohms. Running a bridged output into a 2-ohm load is not supported and risks amplifier failure or NOMAD-triggered protection shutdown. In standard stereo mode, the minimum impedance per channel is 2 ohms. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10" Punch P3S Shallow Stamped Steel Grille Insert Black. Fits Gen-2 P3S Trim Rings. Protects Against Cone and Surround Damage. Product Overview The Rockford Fosgate P3SG-10 is a 10" stamped steel mesh grille insert in black designed to protect the anodised aluminium cone and Santoprene surround of Gen-2 Punch P3S shallow subwoofers from physical damage in boot and under-seat installations. The grille inserts into the trim ring already fitted to the subwoofer no separate hardware is required. The trim ring (included with the P3S subwoofer) must be in place to hold the grille securely. Compatible with Gen-2 P3S 10" subwoofers specifically confirm the generation of your P3S subwoofer before purchasing, as this grille is not confirmed to fit all P3S variants. Key Specifications Part number: P3SG-10 Compatible size: 10 inch (shallow P3S) ✓ Grille type: Stamped mesh insert ✓ Material: Stamped steel ✓ Colour: Black ✓ Fitment: Inserts into Gen-2 P3S trim rings ✓ Trim ring required: Yes — trim ring supplied with subwoofer ✓ Generation compatibility: Gen-2 P3S only ✓ Protection: Surround and cone damage ✓ Compatible SKUs: Select Gen-2 P3S models — confirm with Rockford Fosgate Pack quantity: Not confirmed — confirm with Rockford Fosgate Dimensions: Not confirmed — confirm with Rockford Fosgate Weight: Not confirmed Warranty: Not confirmed — confirm with Rockford Fosgate Features & Benefits Stamped Steel Mesh — Physical Cone and Surround Protection Boot environments expose subwoofer cones to contact damage from luggage, sporting equipment, and cargo movement. The stamped steel mesh sits across the woofer opening — preventing direct contact with the aluminium cone and Santoprene M-Roll surround that would otherwise be exposed in an open or grille-less installation. Stamped steel provides rigid protection while the mesh pattern allows bass to radiate without obstruction. Fits Gen-2 P3S Trim Rings — Simple Insertion Installation The grille inserts directly into the existing trim ring on the subwoofer — no drilling, fasteners, or adhesive required. The trim ring (already included with the P3SD2-10 or P3SD4-10) secures the grille in position. The installation is reversible — the grille can be removed for inspection or cleaning without tools. Black Finish — OEM Appearance The black powder or paint finish matches the P3S subwoofer's anodised cone aesthetic — maintaining a cohesive appearance in both open and grille-covered installations. Gen-2 P3S Specific — Precise Sizing The P3SG-10 is sized specifically for Gen-2 P3S 10" woofers. Confirm the generation of your subwoofer before purchasing — older P3S or standard (non-shallow) P3 models use different trim ring dimensions and this grille will not fit correctly. Technical Specs Specification Detail Brand Rockford Fosgate Part Number P3SG-10 Series Punch P3S (Shallow) Gen-2 Compatible Size 10 inch shallow ✓ Grille Type Stamped Mesh Insert ✓ Material Stamped Steel ✓ Colour Black ✓ Fitment Inserts into Gen-2 P3S trim ring ✓ Trim Ring Required Yes (supplied with subwoofer) ✓ Generation Gen-2 P3S only ✓ Compatible SKUs Select Gen-2 P3S models (confirm with Rockford Fosgate) Pack Quantity Not confirmed Dimensions Not confirmed Weight Not confirmed Warranty Not confirmed Compatible With / Goes Well With Confirmed compatible platform: Gen-2 Punch P3S 10" shallow subwoofers  Likely compatible (confirm before purchasing): Rockford Fosgate P3SD2-10 Punch P3S 10" Shallow 2-Ohm DVC Subwoofer Rockford Fosgate P3SD4-10 Punch P3S 10" Shallow 4-Ohm DVC Subwoofer Frequently Asked Questions Does the trim ring come with the P3SG-10? No — the grille inserts into the trim ring that is already supplied with the P3S subwoofer. The P3SG-10 grille insert only — the trim ring is included with the P3SD2-10 or P3SD4-10 subwoofer purchase. Will the P3SG-10 fit older (non-Gen-2) P3S subwoofers? The P3SG-10 is sized for Gen-2 P3S trim rings specifically. Confirm the generation of your P3S subwoofer with Rockford Fosgate before purchasing — the grille will not fit correctly in earlier-generation trim rings. Does this grille affect bass output? The stamped mesh design is an open structure — bass frequencies radiate through the mesh without significant acoustic obstruction. Some minor high-frequency colouration from the mesh is possible but bass output is not meaningfully affected. Is the P3SG-10 sold as a single unit or a pair? Pack quantity is not confirmed in the supplier data. Confirm from the official Rockford Fosgate P3SG-10 product page before ordering to ensure you purchase the correct quantity for a stereo subwoofer installation. Is there a grille available for the P3S 12" and 8" subwoofers? Yes — the P3SG-12 is the corresponding grille for the 12" P3S platform. An 8" variant (P3SG-8) may also exist — confirm all available P3S grille insert SKUs with Rockford Fosgate. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10" P3S Shallow 4-Ohm DVC 300W RMS, 83dB, 42Hz Fs, 89mm Depth, 230mm Cutout. Confirmed Enclosure Volumes: 14.1L Sealed, 28.3L Vented. Product Overview The Rockford Fosgate Punch P3SD4-10 is a 10" 4-Ohm Dual Voice Coil (DVC) shallow subwoofer rated at 300W RMS (600W peak) the most completely specified P3S model in the supplier data. The full specification set includes 83dB sensitivity, 42Hz free-air resonance, 8.1mm Xmax, 89mm (3.50") mounting depth, 230mm (9.06") cutout diameter, and Rockford Fosgate's confirmed enclosure recommendations: 0.5 cu ft (14.1 litres) sealed, 1.0 cu ft (28.3 litres) vented. CEA-2031 compliant. Input terminals are confirmed Dual 10-AWG compression consistent with the P3D2-10 and P2D4-10 spec tables, and confirming that "push terminals" in P3S features lists is a supplier data error. The 4-Ohm DVC provides wiring options of 2-Ohm (parallel), 8-Ohm (series), or 4-Ohm per coil for bi-amplification no 1-Ohm stability requirement. All confirmed P3S construction applies: anodised aluminium cone and dustcap, M-Roll Santoprene surround, dual linear spider, StampCast basket with spider venting, and diamond-cut cast aluminium trim ring. Key Specifications Subwoofer size: 10 inch (shallow) Voice coil configuration: Dual Voice Coil (DVC) Impedance: 4-Ohm per coil (2-Ohm parallel / 8-Ohm series / 4-Ohm biamp) Power handling (RMS): 300W ✓ (CEA-2031) Power handling (peak): 600W ✓ Sensitivity (SPL): 83dB @ 1W/1M ✓ Free-air resonance (Fs): 42Hz ✓ Xmax: 8.1mm ✓ Mounting depth: 3.50" (89mm) ✓ Cutout diameter: 9.06" (230mm) ✓ Voice coil diameter: 2.5" (65.5mm) ✓ Magnet weight: 47 oz (1.32 kg) ✓ Effective piston area (Sd): 333 cm² ✓ Equivalent air volume (Vas): 14.3 litres ✓ Total Q (Qts): 0.78 ✓ Electrical Q (Qes): 0.90 ✓ Mechanical Q (Qms): 6.00 ✓ Voice coil inductance (Le): 4.3 mH ✓ DC resistance (Re): 6.80 Ohms ✓ Woofer displacement: 0.074 cu ft (2.1 litres) ✓ Recommended sealed enclosure: 0.5 cu ft (14.1L) ✓ Recommended vented enclosure: 1.0 cu ft (28.3L) ✓ Shipping weight: 11.9 lbs (5.39 kg) ✓ CEA-2031 compliant: Yes ✓ Input terminals: Dual 10-AWG compression ✓ Cone: Anodised aluminium ✓ Dustcap: Anodised aluminium ✓ Surround: M-Roll Santoprene ✓ Spider: Dual linear with embedded 16 AWG tinsel leads ✓ Basket: StampCast with integrated spider venting ✓ Trim ring: Diamond-cut cast aluminium (grille insert compatible) ✓ Motor assembly: Shallow ✓ Enclosure compatibility: Sealed and vented ✓ Sold as: Individual unit Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 300W RMS / 600W Peak — CEA-2031 — 300W RMS confirmed to the CEA-2031 standard — the same sustained power as the P3SD2-10, delivered in the 4-Ohm impedance format. 89mm Mounting Depth — Confirmed — At 3.50" (89mm), the P3SD4-10's mounting depth is confirmed. This is significantly shallower than the standard P3D2-10 (156.8mm) — making the P3SD4-10 suitable for shallow enclosures, rear doors with limited depth, or under-seat installations that the full-depth P3 cannot fit. 230mm Cutout Diameter — The confirmed 9.06" (230mm) cutout is slightly smaller than the standard 10" P3 (232mm) — check baffle dimensions against this confirmed figure. Confirmed Enclosure Volumes: Sealed: 0.5 cu ft (14.1 litres) Vented: 1.0 cu ft (28.3 litres) 83dB Sensitivity — The 83dB @ 1W/1M is slightly lower than the standard P3D4-10 (from the P3D2-10's 82dB reference), consistent with the shallow motor's Fs of 42Hz and Qts of 0.78. 42Hz Free-Air Resonance (Fs) — The Fs of 42Hz is higher than full-depth P3 subwoofers (P3D2-10: 26.6Hz), reflecting the shallow motor's stiffer suspension. This affects the enclosure design: the sealed box resonance will be higher than full-depth drivers in the same volume. 8.1mm Xmax — 8.1mm of linear peak excursion — less than the 15.2mm of the full-depth P3D2-10, consistent with the shallow motor's reduced excursion range. Qts = 0.78 — The higher Qts (versus 0.49 for the full-depth P3D2-10) is characteristic of shallow motor designs. At 0.78, the driver is well-suited to the 14.1L sealed box recommendation; the vented alignment at 28.3L provides additional output at bass frequencies above the port tuning point. 4-Ohm DVC — Broad Amplifier Compatibility: 2-Ohm (parallel): Most common configuration 8-Ohm (series): For amplifiers with higher minimum impedance 4-Ohm per coil (biamp): Separate channels Compression Terminals Confirmed — The spec table confirms Dual 10-AWG compression — the correct terminal type across the P2/P3/P3S range. Update all P3S features list descriptions accordingly. Anodised Aluminium Cone, M-Roll Santoprene Surround — P3S platform materials confirmed. Technical Specs Specification Detail Brand Rockford Fosgate Part Number P3SD4-10 Series Punch P3S (Shallow) Subwoofer Size 10 inch (shallow) Voice Coil Dual Voice Coil (DVC) Impedance per Coil 4-Ohm ✓ Wiring Options 2-Ohm (parallel) / 8-Ohm (series) / 4-Ohm biamp ✓ Power Handling (RMS) 300W ✓ (CEA-2031) Power Handling (Peak) 600W ✓ Sensitivity 83dB @ 1W/1M ✓ Fs 42Hz ✓ Xmax 8.1mm ✓ Cutout Diameter 9.06" (230mm) ✓ Mounting Depth 3.50" (89mm) ✓ Voice Coil Diameter 2.5" (65.5mm) ✓ Magnet Weight 47 oz (1.32 kg) ✓ Sd 333 cm² ✓ Vas 14.3 litres ✓ Qts 0.78 ✓ Qes 0.90 ✓ Qms 6.00 ✓ Le 4.3 mH ✓ Re 6.80 Ohms ✓ Woofer Displacement 0.074 cu ft / 2.1L ✓ Sealed Enclosure (Vb) 0.5 cu ft (14.1L) ✓ Vented Enclosure (Vb) 1.0 cu ft (28.3L) ✓ Shipping Weight 11.9 lbs (5.39 kg) ✓ CEA-2031 Compliant Yes ✓ Input Terminals Dual 10-AWG Compression ✓ Cone Anodised Aluminium ✓ Dustcap Anodised Aluminium ✓ Surround M-Roll Santoprene ✓ Spider Dual Linear, Embedded 16 AWG Tinsel Leads ✓ Basket StampCast with Integrated Spider Venting ✓ Motor Shallow ✓ Trim Ring Diamond-Cut Cast Aluminium (Grille Compatible) ✓ Enclosure Type Sealed and Vented ✓ Sold As Individual Unit Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Confirmed enclosure volumes: Sealed: 0.5 cu ft (14.1 litres) net internal Vented: 1.0 cu ft (28.3 litres) net internal — confirm port dimensions from Rockford Fosgate Wiring: 2-Ohm → parallel 8-Ohm → series 4-Ohm per coil → biamp Pairs well with: A mono amplifier rated at 300W RMS at 2-Ohm A shallow sealed 14.1L or vented 28.3L enclosure Weight 5.39 kg (11.9 lbs) Frequently Asked Questions What are the confirmed enclosure volumes for the P3SD4-10? Sealed: 0.5 cu ft (14.1 litres); Vented: 1.0 cu ft (28.3 litres). Both are Rockford Fosgate's official confirmed recommendations. Confirm vented port dimensions from the official P3SD4-10 installation guide. Why is the Fs of the P3SD4-10 higher than a full-depth subwoofer? An Fs of 42Hz reflects the shallow motor's stiffer suspension — required to control the cone within a reduced excursion range. Full-depth subwoofers with long-travel motors have lower Fs values (e.g. the P3D2-10 at 26.6Hz) because their suspensions are more compliant over a greater travel distance. The higher Fs means the P3SD4-10's useful bass extension begins at a higher frequency than full-depth drivers. What is the confirmed mounting depth? 89mm (3.50") — confirmed in the specification table. What does the 230mm cutout mean for enclosure building? A 9.06" (230mm) cutout is required in the baffle. This is 2mm smaller than the standard 232mm cutout on the full-depth P3D4-10 and P2D4-10 — a meaningful difference if using a pre-drilled enclosure. Confirm the exact cutout before purchase. Are the terminals push or compression? The specification table confirms Dual 10-AWG compression terminals — the correct type across the P2, P3, and P3S range. The "push terminals" language in features lists is a consistent supplier data error. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Small chassis. Full range. Punch power for sub or centre channel builds. Product Overview The Rockford Fosgate P300X1 is a 300W mono amplifier from the Punch series, built around a compact chassis capable of fitting where conventional amplifiers cannot. Unlike dedicated subwoofer-only mono amplifiers, the P300X1 features a full-range frequency response making it equally suited to powering a dedicated subwoofer system or a single centre channel speaker. Whether you're running one driver or multiple speakers off a single channel, the 2-ohm capable design delivers 300W of Punch-series output with headroom to spare. The P300X1 is a feature-rich unit for its class. The built-in C.L.E.A.N. setup system simplifies gain calibration, reducing the risk of clipping and distortion from a poorly set amplifier. High-level inputs with an Auto Turn-On circuit allow direct integration with factory head units without requiring a dedicated remote turn-on wire. RCA pass-through outputs enable daisy-chaining to additional amplifiers, and the stealth top-mounted control panel keeps all adjustments accessible without removing the amplifier from its install location. An optional PLC2 remote Punch Level Control (sold separately) connects to add driver-accessible output adjustment and an input clip indicator for real-time gain monitoring. Key Specifications Channels: 1 (mono) Output power: 300W @ 2 ohms (power at other impedances — not specified) Frequency response: Full-range (exact Hz range — not specified) Circuit topology: Not specified Crossover: 12dB/octave Butterworth (frequency range — not specified) Punch EQ: +18dB boost @ 45Hz (see Red-flags) Signal input: High level with Auto Turn-On Signal output: RCA pass-through Remote control: Optional PLC2 (not included — sold separately) Clip indicator: Yes (active when PLC2 is connected) Control panel: Top-mounted (stealth) Setup system: C.L.E.A.N. Input sensitivity: Not specified Nominal impedance load: Not specified CEA compliance: Not specified in provided data Power wire gauge: Not specified Speaker wire gauge: Not specified Operating voltage: Not specified Recommended fuse: Not specified Dimensions: Not specified Features & Benefits Full-Range Frequency Response — Sub or Centre Channel — Most compact mono amplifiers are subwoofer-only units with a fixed low-pass filter. The P300X1's full-range response opens up a second use case: powering a dedicated centre channel speaker in a vehicle with a more complex audio setup. One amplifier, two legitimate applications. C.L.E.A.N. Setup System — Rockford Fosgate's C.L.E.A.N. (Clean Level Efficient Amplifier Noise) setup process uses an on-board indicator to guide accurate gain calibration between the head unit and amplifier. Setting gain by ear or by eye is a common cause of distortion and clipping — C.L.E.A.N. removes the guesswork, protecting your speakers and ensuring the amplifier performs to its rated output without distortion. High-Level Input with Auto Turn-On — The P300X1 accepts high-level speaker wire inputs from factory or OEM head units and powers on automatically when it detects signal — no remote turn-on wire required. This significantly simplifies integration with factory audio systems, particularly in vehicles where accessing the head unit remote output is difficult or impractical. On-Board Punch EQ (+18dB @ 45Hz) — A bass boost centred at 45Hz is available directly from the amplifier, allowing low-end tuning without an external equaliser. The +18dB figure is sourced from the supplier features list — refer to Red-flags below for an important note on this specification. Optional PLC2 Remote Level Control with Clip Indicator — The P300X1 is wired ready for the optional Rockford Fosgate PLC2 remote level control (sold separately). When connected, the PLC2 adds driver-accessible output adjustment and activates an input clip indicator — a LED that warns when the incoming signal is clipping before it reaches the amplifier. This combination helps protect speakers and ensures clean output at all listening levels. RCA Pass-Through Outputs — Signal can be chained to a second amplifier via the RCA pass-through outputs, enabling clean multi-amp builds without splitters or Y-adaptors. Useful in systems running the P300X1 on a centre channel or sub with a separate amplifier on front and rear speakers. Stealth Top-Mounted Control Panel — All controls — gain, crossover, EQ — are located on the top surface of the amplifier rather than on the endplate. This allows access to adjustments after installation in boot floors, under-seat locations, or tight enclosures without the need to remove or reposition the unit. Compact Chassis — The P300X1 is specifically designed to fit installation locations where a conventional amplifier will not physically fit. Exact dimensions are not specified in supplier-provided data — confirm with Rockford Fosgate before planning a space-critical install. Muted Turn-On + Full Protection Circuit — Muted turn-on prevents startup thumps that can stress tweeters and subwoofer cones. Over-current and short-circuit protection safeguard the amplifier and connected drivers during fault conditions. Technical Specs Specification Detail Channels 1 (mono) Output power 300W @ 2Ω Power by impedance Not specified Frequency response Full-range (Hz range not specified) Circuit topology Not specified Crossover type 12dB/octave Butterworth Crossover frequency range Not specified Punch EQ +18dB @ 45Hz (unverified — see Red-flags) Signal input High level (auto turn-on) Signal output RCA pass-through Setup system C.L.E.A.N. Remote control Optional PLC2 (sold separately) Clip indicator Yes (when PLC2 connected) Control panel Top-mounted (stealth) Turn-on method Auto (from high-level input signal) Muted turn-on Yes Protection Over-current / Short circuit Input sensitivity Not specified CEA compliance Not specified Power wire gauge Not specified Speaker wire gauge Not specified Operating voltage Not specified Recommended fuse Not specified Dimensions Not specified Weight 4.3 kg Compatible With / Goes Well With The P300X1 is confirmed for the following applications based on manufacturer-provided information: Dedicated subwoofer systems (single driver or multiple speakers on one channel) Dedicated centre channel speaker amplification (full-range frequency response confirmed) 2-ohm subwoofer or speaker loads (300W RMS — power at other impedances not confirmed) Factory head units without RCA outputs (via high-level Auto Turn-On input) Goes well with: Rockford Fosgate Punch series subwoofers or centre channel drivers rated to 300W Rockford Fosgate PLC2 Remote Punch Level Control (optional — sold separately) Factory head units or OEM audio systems (via high-level auto turn-on) Aftermarket head units with RCA preamp outputs Frequently Asked Questions Can the P300X1 power a centre channel speaker as well as a subwoofer? Yes. Unlike most compact mono amplifiers, the P300X1 features a full-range frequency response — making it suitable for a dedicated centre channel speaker or a subwoofer system. The exact frequency range is not confirmed in the provided data; verify with Rockford Fosgate for your specific application. What is the C.L.E.A.N. setup system? C.L.E.A.N. is Rockford Fosgate's on-board gain calibration system. It uses an indicator to guide correct gain matching between the head unit and amplifier, preventing clipping and distortion that commonly results from gain set too high — protecting speakers and maximising clean output. Is the Punch Level Control included with the P300X1? No. The PLC2 remote Punch Level Control is an optional accessory and is sold separately. The P300X1 is wired and ready to accept the PLC2, and when connected it adds driver-accessible level control and an active input clip indicator. Does the Auto Turn-On circuit require a remote wire from the head unit? No. The high-level Auto Turn-On circuit powers the amplifier when it detects signal at the speaker-level inputs — no dedicated remote turn-on wire is needed. This simplifies installation with factory head units where accessing the remote output is difficult. Can I chain another amplifier off the P300X1? Yes. RCA pass-through outputs allow signal to be routed to a second amplifier cleanly, without splitters or Y-adaptors. This is useful in systems running the P300X1 alongside a separate full-range or multichannel amplifier. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate P300-8P Punch 8" 300 Watt Powered Vented Enclosure When space is the deciding factor but bass cannot be left behind, the P300-8P packs a high-output 8" woofer and 300-watt Class D amplifier into a slim vented enclosure suited for trucks and small car applications alike. Product Overview The P300-8P is Rockford Fosgate's compact all-in-one powered subwoofer enclosure, designed for installations where a 10" or 12" powered enclosure will not fit but genuine low-end performance is still required. The slim vented MDF enclosure houses an 8" proprietary woofer impedance-optimised for the integrated 300-watt Class D amplifier in a closed-loop design, ensuring the driver and amplifier work together as a matched system from the factory. The vented slot-port enclosure extends low-frequency output down to 30 Hz, delivering powerful bass reproduction from a compact footprint. An onboard variable Low-Pass crossover (50-200 Hz), Bass EQ with 0 to +12 dB of boost, and a 0-180 degree phase switch are accessible on the amplifier plate, while the included Punch Level Control remote handles bass adjustment from the driver's seat. An intelligent auto turn-on/off circuit with three selectable modes (Remote Trigger, DC Offset Sense, and Audio Sense) eliminates the need for a dedicated remote turn-on wire in OEM installations. Separate RCA and high-level speaker inputs make it compatible with both aftermarket and factory head units. Quick-release input connectors allow the enclosure to be removed when space is needed. The heat-activated vinyl finish resists marks and scuffs in daily use. CEA-2006 (amplifier) and CEA-2031 (woofer) compliant, Klippel verified, with a 1-year warranty. Features & Benefits 300-Watt Class D Amplifier with Closed-Loop Design: The integrated amplifier is an impedance-matched, closed-loop Class D design tuned specifically for the P300-8P's proprietary 8" woofer, ensuring maximum efficiency and precise driver control at all output levels within the compact enclosure footprint. High-Efficiency, Low Current Amplifier Design: The Class D amplifier topology keeps current consumption low relative to output, making the P300-8P compatible with stock electrical systems in trucks and small vehicles where alternator capacity has not been upgraded. Vented Enclosure for Extended Low-Frequency Output: The slot-port vented enclosure extends bass reproduction down to 30 Hz, providing powerful low-frequency output from an 8" driver in a slim footprint, suited to both truck under-seat and small car boot installations. Slim Design for Truck and Small Car Applications: The compact enclosure dimensions make the P300-8P well suited to tight installation locations, including truck under-seat positions and the limited boot spaces of sub-compact and small hatchback vehicles. Klippel Verified Woofer: The 8" proprietary woofer has been verified through the Klippel certification programme, which measures and corrects non-linear distortion parameters to deliver the best possible transient accuracy and low-frequency output from a compact, impedance-matched driver. Intelligent Auto Turn-On/Off: Three selectable turn-on modes (Remote Trigger, DC Offset Sense, and Audio Sense) allow the P300-8P to power on automatically in any installation scenario, including factory head units without a dedicated remote output. Variable Low-Pass Crossover: Continuously variable from 50 to 200 Hz at 12 dB/octave Butterworth, the onboard crossover integrates cleanly with full-range speakers across virtually any crossover point set by the main system amplifier or head unit. Onboard Bass EQ: 0 to +12 dB of onboard bass boost corrects for acoustic deficiencies in the vehicle interior and adds presence to the low-frequency output without an external equaliser. Phase Switch: A 0 to 180 degree phase control allows the subwoofer to be time-aligned with the main speakers acoustically, compensating for physical placement differences for a coherent, integrated bass response. Included Punch Level Control Remote: The Punch Level Control is included in the box, allowing bass output to be adjusted from the driver's seat in real time without accessing the amplifier plate directly. Quick-Release Input Connections: Input connections use quick-disconnect fittings, allowing the enclosure to be removed from the vehicle quickly when cargo or passenger space is needed, without tools or cable work. High and Low-Level Inputs: Separate RCA (low-level, 150mV-6V) and speaker-level (high-level, 300mV-12V) inputs via a single RCA pair summed L/R support both aftermarket and OEM head unit installations from the same unit. Thermal and Over/Under Voltage Protection: Onboard protection monitors both operating temperature and supply voltage, shutting the amplifier down safely before damage occurs under fault conditions. Precision MDF Enclosure with Vinyl Finish: Constructed from 5/8" Medium Density Fiberboard for optimal acoustic properties, covered with a heat-activated vinyl finish that resists marks and scuffs in daily use. CEA-2006 and CEA-2031 Compliant: Amplifier power ratings conform to CEA-2006 industry standards at 14.4V with 1% or less THD. Woofer power handling conforms to CEA-2031, confirming both ratings are real, tested figures. Technical Specs Specification Detail SKU P300-8P Series Punch Woofer Size 8" Woofer Quantity 1 Woofer Series Proprietary Power Handling 300W RMS Integrated Amplifier 300W RMS Amplifier Class Class D Enclosure Type Vented Enclosure Material 5/8" MDF Enclosure Finish Heat-Activated Vinyl Frequency Response 30 Hz - 200 Hz Low-Pass Crossover Variable 50-200 Hz @ 12 dB/octave Butterworth Bass EQ 0 to +12 dB Phase Control 0 to 180 degrees Input Switch High-Level (Speaker) / Low-Level (RCA) Signal Input 1 x RCA Pair (L/R Summed) Input Sensitivity (Low-Level) 150 mV - 6V Input Sensitivity (High-Level) 300 mV - 12V Input Impedance 20k Ohms Auto Turn-On Selector Remote Trigger / DC Offset Sense / Audio Sense Remote Control Punch Level Control (included) Visual Indicators POWER / PROTECT LED Heatsink Type Extruded Aluminium Cooling Convection Power Wire Gauge 8 AWG (B+/GND), 18 AWG (Remote) Power Input Connector Quick Disconnect Fuses 20A total (2 x 10A ATO) Compliance CEA-2006 (amplifier), CEA-2031 (woofer), Klippel Verified Dimensions (H x W x D) 11.4" x 17.6" x 5.6" (289 mm x 448 mm x 141 mm) Shipping Weight 19 lbs (8.6 kg) Warranty 1 Year Goes Well With The P300-8P is a standalone bass solution requiring no separate subwoofer amplifier or enclosure. For factory head unit installations, the high-level speaker inputs and Audio Sense auto turn-on allow direct connection without additional interface hardware. For aftermarket head unit installations, the RCA input connects directly from the head unit's subwoofer pre-out. To complement the P300-8P with front and rear speaker amplification, the PBR400X4D or R2-200X2 pair naturally via a standard RCA pre-out from the head unit. For installations in trucks where a larger driver is preferred and space allows, the P300-10T or P300-12T are direct step-up options in the same powered truck enclosure range. An 8-gauge power and ground cable run to the battery is required, along with the 2 x 10A ATO fuses included in the box. Frequently Asked Questions How does the P300-8P differ from the P300-10T and P300-12T? All three are 300-watt powered enclosures sharing the same amplifier specification, feature set, and installation approach. The P300-8P uses an 8" vented enclosure with a frequency response from 30 Hz and the smallest physical footprint, making it the right choice for the tightest installation spaces in small cars and trucks. The P300-10T and P300-12T use sealed enclosures with 10" and 12" drivers respectively, each in progressively larger wedge-profile enclosures suited to larger truck under-seat locations where more space is available. Why does the P300-8P use a vented enclosure while the P300-10T and P300-12T are sealed? The vented design allows the 8" driver to produce extended low-frequency output down to 30 Hz, matching the low-end reach of the larger sealed 10" and 12" enclosures despite the smaller driver size. The port tuning compensates for the reduced cone area of the 8" woofer, delivering strong bass output from a notably more compact enclosure footprint. Can the P300-8P be connected directly to a factory head unit? Yes. The high-level speaker inputs accept signal from the factory head unit's speaker outputs directly, and the Audio Sense or DC Offset Sense auto turn-on modes allow the enclosure to power on without a dedicated remote turn-on wire. This makes the P300-8P a straightforward plug-in bass upgrade for OEM systems without requiring head unit replacement. What are the three auto turn-on modes, and which should I use? Remote Trigger mode powers the amplifier on when a 12V signal is received at the remote input terminal, requiring a remote turn-on wire from the head unit. DC Offset Sense mode detects a DC voltage change on the high-level speaker input to trigger turn-on, suitable for OEM systems where the speaker output changes state when the head unit powers on. Audio Sense mode detects an incoming audio signal and triggers turn-on automatically, making it the most universal option for both OEM and aftermarket installations without a dedicated remote output. What is Klippel Verification, and why does it matter for a compact powered enclosure? Klippel is an independent speaker measurement and certification programme that identifies and corrects non-linear distortion parameters in speaker drivers, including suspension non-linearities and motor force variation across the cone's travel range. In a compact powered enclosure where the driver and amplifier are a matched system and the 8" cone is working hard to deliver 30 Hz output, Klippel verification confirms that the woofer's performance envelope has been accurately measured and optimised to deliver clean, low-distortion bass at the rated 300 watts across its full operating range. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

12" 2-Ohm DVC Punch P2 Subwoofer 400W RMS, Kevlar Cone, VAST, Dual Spider, Diamond-Cut Cast Aluminium Trim Ring, Extended Pole Piece. Product Overview The Rockford Fosgate Punch P2D2-12 is a 12" 2-Ohm Dual Voice Coil (DVC) subwoofer rated at 400W RMS the highest confirmed power rating in the Punch P2 series to this point in the catalogue, and a 100W step up from the P2 10" models. The larger 12" cone moves more air than the 10" format for greater bass output and lower frequency extension. The 2-Ohm DVC provides wiring options of 1-Ohm (parallel), 4-Ohm (series), or 2-Ohm per coil for bi-amplification. Optimised for sealed and vented enclosures. Sold as an individual unit. All confirmed Punch P2 construction applies: Kevlar fibre-reinforced paper cone, VAST surround (up to 25% increased cone area), high-temperature voice coil with spun-laced Nomex® reinforcement collar, dual linear spider with embedded 16 AWG tinsel leads, extended pole piece with bumped vented backplate, StampCast basket with integrated spider venting, diamond-cut cast aluminium trim ring with grille insert provision, and protective PVC textured magnet cover. Key Specifications Subwoofer size: 12 inch Voice coil configuration: Dual Voice Coil (DVC) Impedance: 2-Ohm per coil (1-Ohm parallel / 4-Ohm series / 2-Ohm biamp) Power handling (RMS): 400W (confirmed) Peak power: Not specified — confirm with Rockford Fosgate Surround technique: VAST (up to 25% increased cone area) Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Xmax: Not specified — confirm with Rockford Fosgate Cutout diameter: Not specified — confirm with Rockford Fosgate Mounting depth: Not specified — confirm with Rockford Fosgate Voice coil: High-temp, Nomex® reinforcement collar Cone: Kevlar fibre-reinforced paper Spider: Dual linear with embedded 16 AWG tinsel leads Basket: StampCast with integrated spider venting Pole piece: Extended Backplate: Bumped and vented Input terminals: Features: push — confirm vs compression with Rockford Fosgate Trim ring: Diamond-cut cast aluminium (grille insert compatible) Magnet cover: Protective PVC textured Enclosure compatibility: Sealed and vented ✓ Sold as: Individual unit Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 400W RMS — 400W RMS is the highest confirmed power handling in the P2 series and among all subwoofers in this catalogue to date. Requires an amplifier rated at 400W RMS at the selected impedance configuration. 12" Cone — Greater Air Movement — More air movement and lower frequency extension than the 10" P2D2-10 in comparable enclosures. 2-Ohm DVC — Three Wiring Options: 1-Ohm (parallel): Confirm amplifier rated stable at 1-Ohm before use 4-Ohm (series): Broad amplifier compatibility 2-Ohm per coil (biamp): Separate amplifier channels Dual Linear Spider — Two spiders for improved compliance linearity and cone control at high excursion. Kevlar Fibre-Reinforced Paper Cone with VAST — Stiffened paper cone plus up to 25% increased effective radiating area. Nomex® Voice Coil Reinforcement Collar — Thermal and mechanical durability at 400W sustained. Extended Pole Piece and Bumped Vented Backplate — Increased linear excursion; air spring prevention. Diamond-Cut Cast Aluminium Trim Ring — Premium machined aluminium finish with grille insert provision. StampCast Basket with Integrated Spider Venting — Motor cooling. Technical Specs Specification Detail Brand Rockford Fosgate Part Number P2D2-12 Series Punch P2 Subwoofer Size 12 inch Voice Coil Dual Voice Coil (DVC) Impedance per Coil 2-Ohm ✓ Wiring Options 1-Ohm (parallel) / 4-Ohm (series) / 2-Ohm biamp ✓ Power Handling (RMS) 400W ✓ Peak Power Not specified — confirm with Rockford Fosgate Sensitivity Not specified — confirm with Rockford Fosgate Fs / Xmax / Qts Not specified — confirm with Rockford Fosgate Cutout Diameter Not specified — confirm with Rockford Fosgate Mounting Depth Not specified — confirm with Rockford Fosgate Surround Technique VAST ✓ Voice Coil High-Temp, Nomex® Collar ✓ Cone Kevlar Fibre-Reinforced Paper ✓ Spider Dual Linear, Embedded 16 AWG Tinsel Leads ✓ Basket StampCast with Integrated Spider Venting Pole Piece Extended ✓ Backplate Bumped and Vented ✓ Input Terminals Features: push — confirm vs compression with Rockford Fosgate Trim Ring Diamond-Cut Cast Aluminium (Grille Compatible) ✓ Magnet Cover Protective PVC Textured ✓ Enclosure Type Sealed and Vented ✓ CEA-2031 Compliant Not confirmed — confirm with Rockford Fosgate Sold As Individual Unit Weight Not specified Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable enclosure types: Sealed and vented — both confirmed Fitment caution: Cutout diameter, mounting depth, and enclosure volumes not confirmed. Pull from the official Rockford Fosgate P2D2-12 datasheet before building or selecting an enclosure. 1-Ohm wiring caution: Confirm amplifier stability at 1-Ohm before using the parallel configuration. Amplifier note: 400W RMS requires an amplifier rated at 400W RMS at the selected impedance. This is above the 300W rating of the T1000-1BDCP at 2-Ohm — confirm specific amplifier output at the intended load. Pairs well with: Rockford Fosgate T1500-1BDCP or T2500-1BDCP mono amplifiers — confirm RMS output matches 400W at the selected impedance Frequently Asked Questions What amplifier power does the P2D2-12 require? 400W RMS at the selected wiring impedance. This is 100W higher than the P2 10" models. Confirm your amplifier's CEA-2031 rated RMS output at 1-Ohm, 4-Ohm, or 2-Ohm (per coil) before purchasing. What enclosure volume is recommended? Enclosure volumes are not confirmed in the supplier data. Pull the official Rockford Fosgate P2D2-12 datasheet for sealed and vented recommendations. What are the wiring options? 1-Ohm (parallel — confirm amplifier stability), 4-Ohm (series), or 2-Ohm per coil for bi-amplification. Is a grille available? The diamond-cut cast aluminium trim ring accommodates an optional grille insert. Confirm the compatible SKU with Rockford Fosgate. What is the terminal type on the P2D2-12? The features list states "nickel plated push terminals." The P2D4-10 spec table reveals "compression terminals" — a conflict across the P2 range. Confirm the correct terminal type with Rockford Fosgate, as this applies to all P2 subwoofer models simultaneously. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less