JL Audio JLA-010-03430-00 AP 6-Channel Marine Amplifier - Premium IP67-Rated Compact Complete System Amplifier with Class-D Efficiency, 50W x 4 Plus 100W x 2 Multi-Zone Configuration, 300W x 1 Bridged Subwoofer Capability, Independent Variable Crossover Filters, Adjustable Bass Boost EQ, Defeatable Infrasonic Filter, and Professional Marine Audio Performance for Comprehensive Boat Audio Installations Achieve complete marine audio system amplification from single compact unit using JL Audio JLA-010-03430-00 AP 6-Channel Marine Amplifier—combining mid-power channels 1-4 delivering 50W x 4 RMS @ 4 ohm (75W x 4 @ 2 ohm, 150W x 2 bridged) with high-power channels 5-6 producing 100W x 2 RMS @ 4 ohm (150W x 2 @ 2 ohm, 300W x 1 bridged) enabling comprehensive system solutions powering cabin speakers, tower speakers, and subwoofers from single amplifier eliminating multiple amplifier installations, robust IP67 water and dust protection rating ensuring complete dust-tight seal and protection against powerful water jets from any direction safeguarding internal electronics from harsh saltwater spray and moisture intrusion, advanced Class-D amplifier topology delivering exceptional power efficiency with reduced heat generation and minimal current draw enabling compact installation in confined marine equipment compartments, compact dimensions measuring 300mm width x 150mm depth x 47mm height (11.81" x 5.9" x 1.85") fitting under helm panels or small equipment compartments despite powerful six-channel capability, sophisticated independent signal processing per channel pair with channels 1-2, 3-4, and 5-6 each featuring user-selectable Off/Low-Pass/High-Pass filtering with 12dB/octave slopes and 20Hz-500Hz frequency range enabling precise multi-zone speaker and subwoofer integration, adjustable bass boost EQ (0 to +18dB @ 37Hz) enhancing low-frequency response, defeatable infrasonic filter (20Hz-50Hz) on channels 5-6 protecting subwoofers from damaging subsonic frequencies when used for subwoofer duty, full-range frequency response (20Hz-20kHz) suitable for complete audio spectrum reproduction, wide input sensitivity range (200mV-8V RMS) with switchable low/high settings accommodating various source units, excellent signal-to-noise ratio (>70dB) ensuring clean amplification, comprehensive protection circuits including under/over voltage, over-temperature, and short circuit protection, extreme operating temperature range (-20°C to 65°C), minimal standby current (<1mA), efficient idle current (1000-1500mA), 70A fuse protection with AFS/AGU/MaxiFuse compatibility, 4 AWG minimum power/ground wire gauge, extensive compatibility with Fusion and JL Audio M3 marine speakers and subwoofers, three-year warranty, and proven JL Audio engineering delivering professional-grade complete system amplification for recreational boats, fishing vessels, center console boats, and marine applications requiring powerful reliable multi-zone amplification with IP67 protection. Product Overview JL Audio JLA-010-03430-00 AP 6-channel compact marine amplifier with IP67 water/dust rating delivering complete system amplification. Combines mid-power four-channel section with high-power two-channel section enabling speakers and subwoofers from single compact amplifier. Comprehensive power configuration: Channels 1-4 deliver 50W x 4 RMS @ 4 ohm (75W x 4 @ 2 ohm) with 150W x 2 bridged capability for cabin speakers or tower speakers. Channels 5-6 deliver 100W x 2 RMS @ 4 ohm (150W x 2 @ 2 ohm) with 300W x 1 bridged capability for high-power tower speakers or dedicated subwoofer applications. Typical system configurations: channels 1-4 power four cabin speakers while channels 5-6 drive dual tower speakers, channels 1-4 power cabin speakers while channels 5-6 bridged (300W x 1) drive subwoofer, channels 1-2 power helm speakers, channels 3-4 power cockpit speakers, channels 5-6 power tower speakers for complete three-zone system. Independent signal processing per channel pair enables precise system tuning. Channels 1-2, 3-4, and 5-6 each feature user-selectable filtering: Off (full-range 20Hz-20kHz operation), Low-Pass (passes frequencies below selected point for bass speakers or subwoofers), High-Pass (passes frequencies above selected point protecting speakers from excessive bass). Variable crossover range 20Hz-500Hz with 12dB/octave slopes. Defeatable infrasonic filter on channels 5-6 protects subwoofers from damaging subsonic frequencies below 20Hz. Adjustable 20Hz-50Hz range prevents cone over-excursion when channels 5-6 used for subwoofer duty. Adjustable bass boost EQ (0 to +18dB @ 37Hz) enhances low-frequency response across entire system. IP67 water/dust protection provides complete environmental sealing against harsh marine conditions. Advanced Class-D topology delivers exceptional efficiency reducing heat generation. Compact dimensions (300mm x 150mm x 47mm) enable installation in tight spaces despite powerful six-channel capability. Wide input sensitivity range (200mV-8V RMS) with switchable low (200mV-2V RMS) and high (800mV-8V RMS) settings accommodates various source equipment. Excellent signal-to-noise ratio (>70dB) ensures clean amplification. Full-range frequency response (20Hz-20kHz) covers complete audible spectrum. Comprehensive protection circuits safeguard amplifier and speakers: input under/over voltage protection, over-temperature protection, output short circuit protection. Extreme operating temperature range (-20°C to 65°C) ensures reliable performance across seasonal variations. Minimal standby current (<1mA) prevents battery drain. Idle current 1000-1500mA minimizes electrical system impact. 70A fuse protection with AFS/AGU/MaxiFuse compatibility. 4 AWG minimum power/ground wire gauge recommended. Extensive compatibility with Fusion Apollo, RA Series, EL/FM/SM/XS marine speakers, subwoofers, and tower speakers. JL Audio M3 Marine audio products. Complete installation package includes amplifier, mounting screws, and documentation. Three-year manufacturer warranty. Eliminates multiple amplifier installations: single 6-channel amplifier replaces separate 4-channel speaker amplifier plus dedicated subwoofer amplifier reducing equipment quantity, wiring complexity, and installation space requirements while providing comprehensive system control from unified platform. Complete System Amplification - Comprehensive 6-channel configuration combining mid-power channels 1-4 (50W x 4) with high-power channels 5-6 (100W x 2 / 300W x 1 bridged) enabling complete speaker and subwoofer systems from single compact amplifier eliminating multiple amplifier requirements. IP67 Water and Dust Protection - Robust IP67 environmental protection rating providing complete dust-tight seal and protection against powerful water jets from any direction ensuring reliable operation in harsh saltwater spray, moisture exposure, and demanding marine environments. 300W Bridged Subwoofer Capability - High-power channels 5-6 deliver 300W x 1 RMS when bridged @ 4 ohm providing substantial subwoofer amplification from compact six-channel platform eliminating dedicated subwoofer amplifier requirement for complete system installations. Independent Channel Pair Filtering - Sophisticated user-selectable filtering per channel pair: channels 1-2, 3-4, and 5-6 each feature Off/Low-Pass/High-Pass modes with 12dB/octave slopes and 20Hz-500Hz range enabling precise multi-zone speaker and subwoofer integration. Advanced Class-D Efficiency - Class-D amplifier topology delivering exceptional power efficiency, reduced heat generation, minimal current draw, and compact dimensions enabling installation in confined marine spaces while maintaining professional six-channel power output levels. Compact Space-Efficient Design - Optimized dimensions (300mm x 150mm x 47mm / 11.81" x 5.9" x 1.85") enabling installation under helm panels, behind dash areas, or small equipment compartments despite powerful six-channel capability significantly smaller than traditional marine amplifiers. Multi-Zone Configuration Flexibility - Versatile channel allocation supporting various configurations: four cabin speakers plus two tower speakers, four cabin speakers plus bridged subwoofer, helm/cockpit/tower three-zone systems, or custom multi-zone layouts matching specific vessel requirements. Defeatable Infrasonic Filter - Infrasonic filter on channels 5-6 (20Hz-50Hz adjustable, defeatable) protecting subwoofers from damaging subsonic frequencies below audible range preventing cone over-excursion and mechanical damage when channels used for subwoofer duty. Adjustable Bass Boost EQ - Variable bass boost control providing 0 to +18dB gain at 37Hz enhancing low-frequency response for systems requiring additional bass impact or supplementing existing subwoofer systems with adjustable enhancement across entire system. Flexible Bridging Capability - Channels 1-4 support 150W x 2 bridged for high-power two-channel applications, channels 5-6 support 300W x 1 bridged for dedicated subwoofer driving providing flexible power configuration options matching diverse system requirements. Switchable Input Sensitivity - Wide input sensitivity range (200mV-8V RMS) with switchable low (200mV-2V RMS) and high (800mV-8V RMS) settings accommodating aftermarket and OEM source units with various output levels without requiring additional signal adapters. Excellent Signal-to-Noise Ratio - Superior signal-to-noise ratio (>70dB referred to 1W, A-weighted) ensuring clean amplification with minimal background noise maintaining audio fidelity and professional sound quality throughout six-channel power range. Full-Range Frequency Response - Complete frequency response coverage (20Hz-20kHz, +0/-1dB) delivering accurate reproduction across entire audible spectrum from deep bass frequencies to high treble ensuring balanced natural sound across all six channels. Comprehensive Protection Circuits - Multiple protection systems including input under/over voltage protection, over-temperature protection, and output short circuit protection safeguarding amplifier and connected speakers from electrical faults, overheating, and wiring errors. Extreme Operating Temperature Range - Wide operating temperature range (-20°C to 65°C / -4°F to 149°F) ensuring reliable performance from cold winter storage to hot summer operation in exposed marine installations across all climate conditions. Premium Marine Audio Compatibility - Extensive compatibility with Fusion Apollo, RA Series, EL/FM/SM/XS marine speakers, subwoofers, and tower speakers plus JL Audio M3 Marine audio products ensuring seamless integration with premium marine speaker systems. Technical Specifications Specification Details Model AP (6-Channel) Part Number JLA-010-03430-00 Brand JL Audio Product Type Marine Amplifier (6-Channel) Channels 6 Amplifier Class Class-D Dimensions (W x D x H) 300 x 150 x 47 mm (11.81" x 5.9" x 1.85") Water/Dust Rating IP67 Operating Voltage 9-16 VDC Operating Temperature -20°C to 65°C (-4°F to 149°F) Rated Power @ 4 Ohm Ch. 1-4: 50W x 4 RMS / 150W x 2 bridged; Ch. 5-6: 100W x 2 RMS / 300W x 1 bridged (<1% THD) Rated Power @ 2 Ohm Ch. 1-4: 75W x 4 RMS; Ch. 5-6: 150W x 2 RMS (<1% THD) Frequency Response 20 Hz - 20 kHz (+0, -1dB) Signal-to-Noise Ratio > 70 dB (A-weighted, referred to 1W) THD+N @ Rated Power <1% @ 4 Ω per channel Input Sensitivity 200mV - 8V RMS Input Voltage Range Low: 200mV-2V / High: 800mV-8V (switchable) Input Impedance 11 kΩ (High) / 20 kΩ (Low) Crossover Filters Ch. 1-2, 3-4, 5-6: Off/Low-Pass/High-Pass (20-500Hz, 12dB/octave) Bass Boost EQ 0 to +18 dB @ 37 Hz Infrasonic Filter 20-50 Hz (defeatable, Ch. 5-6 only) Output Polarity Switch No Current Draw (Standby) <1 mA Current Draw (Idle) 1000-1500 mA Fuse Rating 70 A Recommended Fuse Types AFS, AGU, or MaxiFuse Min. Wire Gauge 4 AWG copper Protection Circuits Input under/over voltage, over-temperature, output short circuit Warranty 3 years Included Accessories Amplifier, 4 mounting screws, documentation Frequently Asked Questions Q: What are typical system configurations using the 6-channel amplifier? A: Common configurations include: Four speakers plus subwoofer: Channels 1-4 power cabin speakers with High-Pass filtering (80-120Hz), channels 5-6 bridged (300W x 1) drive subwoofer with Low-Pass filtering (80-100Hz). Four speakers plus tower speakers: Channels 1-4 power cabin speakers, channels 5-6 power tower speakers (100W x 2). Three-zone system: Channels 1-2 helm speakers, channels 3-4 cockpit speakers, channels 5-6 tower speakers or additional zone. Most popular configuration: four cabin speakers plus bridged subwoofer providing complete system from single amplifier. Q: How does the 6-channel compare to using separate amplifiers? A: 6-channel advantages: single amplifier versus multiple units reduces equipment quantity, simplified wiring (one power/ground run), reduced installation space, lower total cost, unified control platform. Provides equivalent power to separate 4-channel (50W x 4) plus monoblock (300W x 1) with single 70A fuse and 4 AWG wiring. Disadvantage: separate amplifiers offer specialized optimization per function. For standard four-speaker plus subwoofer systems: 6-channel provides complete amplification with significantly reduced complexity. Q: Can I use channels 5-6 for tower speakers instead of subwoofer? A: Yes—channels 5-6 support tower speakers or subwoofers. Tower speaker operation: configure as 100W x 2 RMS @ 4 ohm (150W x 2 @ 2 ohm), set High-Pass filtering (80-150Hz) or full-range, disable infrasonic filter. Ideal for tower speakers requiring high SPL for wakeboarding. Alternatively: bridge channels 5-6 (300W x 1) for subwoofer with Low-Pass filtering and infrasonic filter enabled. Flexibility enables system customization: use channels 5-6 for tower speakers on wakeboard boats or bridge for subwoofer on recreational boats prioritizing bass. Q: What wire gauge and fusing do I need for 6-channel installation? A: Required: 4 AWG minimum copper wire (marine-grade tinned) for power and ground, 70A fuse within 18 inches of battery (AFS/AGU/MaxiFuse types), marine-grade fuse holder rated for 70A. Current draw: <1mA standby, 1000-1500mA idle, approaches 70A at maximum output. Verify vessel alternator capacity supports amplifier plus other loads. Ground wire equally important: same 4 AWG gauge, clean metal-to-metal connection to negative bus bar or battery terminal. Professional installation recommended ensuring proper wire sizing and fuse placement meeting marine electrical codes. Q: How do I set the crossover filters for optimal performance? A: Common settings for four speakers plus subwoofer: Channels 1-4 (cabin speakers): High-Pass 80-100Hz for 6.5-inch speakers or 100-120Hz for smaller speakers protecting from excessive bass. Channels 5-6 bridged (subwoofer): Low-Pass 80-100Hz for sealed enclosures or 100-120Hz for ported matching cabin speaker crossover for seamless transition. Adjustment: start with recommended points, play bass-heavy music, adjust by ear for smooth transition without gaps or overlap. Use bass boost judiciously (0-6dB) after crossover settings established. Consult speaker specifications for recommended crossover points preventing damage. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03428-00 AP Monoblock Marine Amplifier - Premium IP67-Rated Compact Subwoofer Amplifier with Class-D Efficiency, 300W x 1 RMS Dedicated Bass Amplification, Optimized 10Hz-500Hz Frequency Response, Variable Low-Pass Crossover, Defeatable Infrasonic Filter, Output Polarity Switch, and Professional Marine Subwoofer Performance for Powerful Boat Bass Systems Achieve powerful dedicated subwoofer amplification using JL Audio JLA-010-03428-00 AP Monoblock Marine Amplifier—delivering substantial 300W x 1 RMS @ 2 ohm (200W x 1 @ 4 ohm) designed specifically for marine subwoofer applications requiring serious bass output, robust IP67 water and dust protection rating ensuring complete dust-tight seal and protection against powerful water jets from any direction safeguarding internal electronics from harsh saltwater spray and moisture intrusion, advanced Class-D amplifier topology delivering exceptional power efficiency with reduced heat generation and minimal current draw enabling compact installation in confined marine equipment compartments, ultra-compact dimensions measuring 265mm width x 125mm depth x 47mm height (10.43" x 4.9" x 1.85") enabling installation under helm panels or small equipment compartments despite powerful monoblock output, specialized frequency response optimized for subwoofer duty spanning 10Hz-500Hz extending below audible range for deep bass reproduction, variable low-pass crossover filter (20Hz-500Hz, 12dB/octave slope) precisely tailoring subwoofer frequency range for optimal integration with main speakers, defeatable infrasonic filter (20Hz-50Hz adjustable) protecting subwoofers from damaging subsonic frequencies below audible hearing range preventing cone over-excursion, output polarity switch (unique to monoblock configuration) enabling phase adjustment for optimal bass integration with main speakers eliminating bass cancellation, adjustable bass boost EQ (0 to +18dB @ 37Hz) enhancing low-frequency response for systems requiring additional bass impact, wide input sensitivity range (200mV-8V RMS) with switchable low/high settings accommodating various source units, excellent signal-to-noise ratio (>70dB) ensuring clean amplification, comprehensive protection circuits including under/over voltage, over-temperature, and short circuit protection, extreme operating temperature range (-20°C to 65°C), minimal standby current (<1mA), efficient idle current (700-750mA), 35A fuse protection with AFS/AGU/MaxiFuse compatibility, 4 AWG minimum power/ground wire gauge, extensive compatibility with Fusion and JL Audio M3 marine subwoofers, three-year warranty, and proven JL Audio engineering delivering professional-grade dedicated subwoofer amplification for recreational boats, fishing vessels, center console boats, and marine applications requiring powerful reliable bass reproduction with IP67 protection. Product Overview JL Audio JLA-010-03428-00 AP monoblock compact marine amplifier with IP67 water/dust rating delivering dedicated subwoofer amplification. Purpose-built for powerful bass reproduction with specialized subwoofer features and optimized frequency response. Substantial power output: 300W x 1 RMS @ 2 ohm (200W x 1 @ 4 ohm) providing serious subwoofer amplification from compact platform. Sufficient power for most marine subwoofer applications including sealed enclosures, ported enclosures, or infinite baffle installations requiring dedicated bass amplification. Specialized subwoofer optimization: Frequency response 10Hz-500Hz optimized for bass reproduction extending below audible range for deep impactful bass. Variable low-pass crossover (20Hz-500Hz, 12dB/octave) precisely tailors subwoofer frequency range integrating optimally with main speakers. Typical crossover settings 80-100Hz for sealed enclosures, 100-120Hz for ported enclosures. Defeatable infrasonic filter (20Hz-50Hz adjustable) protects subwoofers from damaging subsonic frequencies. Subsonic content below 20Hz inaudible to humans but causes excessive cone excursion potentially damaging voice coils or suspensions. Filter prevents mechanical damage while maintaining deep bass extension. Typical setting 25-30Hz provides protection without sacrificing bass impact. Output polarity switch (unique to monoblock) enables phase adjustment. Inverts subwoofer phase (0° or 180°) for optimal bass integration with main speakers. Proper phase alignment prevents bass cancellation ensuring maximum bass output and smooth frequency response transition between speakers and subwoofer. Adjust by ear selecting phase position delivering strongest bass output. Adjustable bass boost EQ (0 to +18dB @ 37Hz) enhances low-frequency response. Use judiciously typically 0-6dB enhancement maintaining system balance without overwhelming main speakers or causing subwoofer over-excursion. IP67 water/dust protection provides complete environmental sealing against harsh marine conditions. Advanced Class-D topology delivers exceptional efficiency reducing heat generation. Ultra-compact dimensions (265mm x 125mm x 47mm) enable installation in tight spaces despite powerful monoblock output. Wide input sensitivity range (200mV-8V RMS) with switchable low (200mV-2V RMS) and high (800mV-8V RMS) settings accommodates various source equipment. Excellent signal-to-noise ratio (>70dB) ensures clean amplification without background noise. Comprehensive protection circuits safeguard amplifier and subwoofer: input under/over voltage protection, over-temperature protection, output short circuit protection. Extreme operating temperature range (-20°C to 65°C) ensures reliable performance across seasonal variations. Minimal standby current (<1mA) prevents battery drain. Idle current 700-750mA minimizes electrical system impact. 35A fuse protection with AFS/AGU/MaxiFuse compatibility. 4 AWG minimum power/ground wire gauge recommended. Extensive compatibility with Fusion FM/XS Series marine subwoofers and JL Audio M3 Marine Subwoofers. Complete installation package includes amplifier, mounting screws, and documentation. Three-year manufacturer warranty. Ideal applications: dedicated subwoofer systems requiring substantial bass amplification, systems with separate 4-channel or 6-channel amplifier already powering cabin speakers, upgrades adding subwoofer to existing speaker systems, applications prioritizing specialized subwoofer controls and optimized bass performance. Dedicated Subwoofer Amplification - Purpose-built monoblock configuration delivering 300W x 1 RMS @ 2 ohm (200W x 1 @ 4 ohm) specifically optimized for marine subwoofer applications requiring serious bass output with specialized subwoofer features and controls. IP67 Water and Dust Protection - Robust IP67 environmental protection rating providing complete dust-tight seal and protection against powerful water jets from any direction ensuring reliable operation in harsh saltwater spray, moisture exposure, and demanding marine environments. Optimized Subwoofer Frequency Response - Specialized frequency response (10Hz-500Hz) optimized for subwoofer duty extending below audible range for deep bass reproduction eliminating unnecessary high-frequency amplification focusing power on bass frequencies. Variable Low-Pass Crossover - Adjustable low-pass filter (20Hz-500Hz, 12dB/octave slope) precisely tailoring subwoofer frequency range for optimal integration with main speakers ensuring seamless transition and preventing frequency overlap. Defeatable Infrasonic Filter - Adjustable infrasonic filter (20Hz-50Hz, defeatable) protecting subwoofers from damaging subsonic frequencies below audible range preventing cone over-excursion and mechanical damage while maintaining deep bass extension. Output Polarity Switch - Phase adjustment switch (unique to monoblock configuration) enabling 0° or 180° polarity inversion for optimal bass integration with main speakers preventing bass cancellation and ensuring maximum output. Advanced Class-D Efficiency - Class-D amplifier topology delivering exceptional power efficiency, reduced heat generation, minimal current draw, and compact dimensions enabling installation in confined marine spaces while maintaining professional monoblock power output. Ultra-Compact Design - Space-efficient dimensions (265mm x 125mm x 47mm / 10.43" x 4.9" x 1.85") enabling installation under helm panels, behind dash areas, or small equipment compartments despite powerful 300W monoblock output. Adjustable Bass Boost EQ - Variable bass boost control providing 0 to +18dB gain at 37Hz enhancing low-frequency response for systems requiring additional bass impact with adjustable enhancement maintaining system balance. Switchable Input Sensitivity - Wide input sensitivity range (200mV-8V RMS) with switchable low (200mV-2V RMS) and high (800mV-8V RMS) settings accommodating aftermarket and OEM source units with various output levels. Excellent Signal-to-Noise Ratio - Superior signal-to-noise ratio (>70dB referred to 1W, A-weighted) ensuring clean amplification with minimal background noise maintaining audio fidelity and professional sound quality. Comprehensive Protection Circuits - Multiple protection systems including input under/over voltage protection, over-temperature protection, and output short circuit protection safeguarding amplifier and connected subwoofer from electrical faults. Extreme Operating Temperature Range - Wide operating temperature range (-20°C to 65°C / -4°F to 149°F) ensuring reliable performance from cold winter storage to hot summer operation in exposed marine installations. Premium Marine Subwoofer Compatibility - Extensive compatibility with Fusion FM/XS Series marine subwoofers and JL Audio M3 Marine Subwoofers ensuring seamless integration with premium marine bass systems. Technical Specifications Specification Details Model AP (Monoblock) Part Number JLA-010-03428-00 Brand JL Audio Product Type Marine Amplifier (Monoblock/Subwoofer) Channels 1 (Monoblock) Amplifier Class Class-D Dimensions (W x D x H) 265 x 125 x 47 mm (10.43" x 4.9" x 1.85") Water/Dust Rating IP67 Operating Voltage 9-16 VDC Operating Temperature -20°C to 65°C (-4°F to 149°F) Rated Power @ 4 Ohm 200W x 1 RMS (<1% THD) Rated Power @ 2 Ohm 300W x 1 RMS (<1% THD) Frequency Response 10 Hz - 500 Hz (+0, -1dB) Signal-to-Noise Ratio > 70 dB (A-weighted, referred to 1W) THD+N @ Rated Power <1% @ 4 Ω Input Sensitivity 200mV - 8V RMS Input Voltage Range Low: 200mV-2V / High: 800mV-8V (switchable) Input Impedance 11 kΩ (High) / 20 kΩ (Low) Crossover Filter Low-Pass (20-500Hz, 12dB/octave) Bass Boost EQ 0 to +18 dB @ 37 Hz Infrasonic Filter 20-50 Hz (defeatable) Output Polarity Switch Yes Current Draw (Standby) <1 mA Current Draw (Idle) 700-750 mA Fuse Rating 35 A Recommended Fuse Types AFS, AGU, or MaxiFuse Min. Wire Gauge 4 AWG copper Protection Circuits Input under/over voltage, over-temperature, output short circuit Warranty 3 years Included Accessories Amplifier, 4 mounting screws, documentation Frequently Asked Questions Q: What subwoofers work best with the AP Monoblock amplifier? A: AP Monoblock (300W x 1 @ 2 ohm, 200W x 1 @ 4 ohm) compatible with marine subwoofers rated 200-300W RMS. Recommended: Fusion FM/XS Series marine subwoofers, JL Audio M3 Marine Subwoofers. Match subwoofer impedance to amplifier: 2-ohm subwoofer delivers 300W output (maximum power), 4-ohm subwoofer delivers 200W output. Subwoofer power handling should match or exceed amplifier output preventing damage. Typical marine subwoofers: 10-inch (200-300W RMS), 12-inch (250-400W RMS). Verify subwoofer marine-grade construction with saltwater resistance. Enclosure requirements: sealed, ported, or infinite baffle depending on subwoofer specifications. Q: How do I set the low-pass crossover and infrasonic filter? A: Low-pass crossover: Start with 80-100Hz for sealed enclosures or 100-120Hz for ported enclosures. Match main speaker high-pass point ensuring seamless transition. Adjust by ear: increase frequency if bass sounds disconnected from main speakers, decrease if main speakers sound muddy or strained. Infrasonic filter: Enable for subwoofer protection. Set 25-30Hz for most applications maintaining deep bass while preventing subsonic damage. Higher settings (35-50Hz) for smaller subwoofers or ported enclosures. Defeat only if subsonic response required (rare). Bass boost: Start at 0dB, increase gradually (typically 3-6dB maximum) if additional bass impact desired without overpowering system or causing distortion. Q: What does the output polarity switch do and how do I use it? A: Output polarity switch inverts subwoofer phase (0° or 180°) for optimal bass integration. Bass waves from subwoofer and main speakers can arrive at listening position in-phase (reinforcing) or out-of-phase (canceling). Adjustment procedure: Play bass-heavy music at moderate volume, switch between 0° and 180° positions, select position delivering stronger deeper bass output (correct phase alignment). Phase issues more noticeable at crossover frequency where subwoofer and speakers overlap. Proper phase alignment ensures maximum bass output and smooth frequency response. Most installations: one position significantly louder indicating correct phase. If minimal difference: phase alignment already optimal or listening position equidistant from speakers/subwoofer. Q: Can I use the Monoblock amplifier for speakers instead of subwoofers? A: Not recommended—Monoblock optimized specifically for subwoofer duty. Frequency response (10Hz-500Hz) limited to bass frequencies unsuitable for full-range speakers requiring 20Hz-20kHz. Low-pass filter (20-500Hz) eliminates high frequencies needed for vocals, instruments, treble. Monoblock designed for single-channel subwoofer operation not multiple speaker configurations. For speakers: use 4-Channel AP amplifier (50W x 4) or 6-Channel AP amplifier (50W x 4 plus 100W x 2). Monoblock advantages (output polarity switch, infrasonic filter, optimized bass frequency response) specifically benefit subwoofer applications. Using Monoblock for speakers results in severely limited frequency response without treble/midrange reproduction. Q: What wire gauge and fusing do I need for Monoblock installation? A: Required: 4 AWG minimum copper wire (marine-grade tinned) for power and ground, 35A fuse within 18 inches of battery (AFS/AGU/MaxiFuse types), marine-grade fuse holder. Current draw: <1mA standby, 700-750mA idle, approaches 35A at maximum output. Ground wire equally important: same 4 AWG gauge, clean metal-to-metal connection to negative bus bar or battery terminal. Heavier gauge acceptable (2 AWG, 1/0 AWG) for longer runs reducing voltage drop. Verify vessel alternator capacity supports amplifier plus other loads. Professional installation recommended ensuring proper wire sizing and fuse placement meeting marine electrical codes.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03342-00 MVi-HUB JLid Communication and Network Bridge - Professional Multi-Amplifier System Integration Hub for MVI Marine Amplifiers, Unified TüN Software Configuration, Synchronized DSP Preset Management, Distributed Digital Remote Controller Commands, Centralized Volume and System Control, and Advanced Marine Audio Networking for Complex Multi-Zone Boat Audio Installations Achieve seamless multi-amplifier system integration using JL Audio JLA-010-03342-00 MVi-HUB JLid Communication and Network Bridge—simplifying configuration and control of complex multi-amplifier marine audio systems by enabling all networked MVI amplifiers to appear in single unified TüN software session eliminating need for separate configuration of individual amplifiers, innovative amplifier networking technology synchronizing DSP presets across all connected amplifiers ensuring consistent system tuning and coordinated audio processing throughout entire vessel, distributed command functionality enabling single optional Digital Remote Controller (M-DRC-50 or DRC-205 sold separately) to control entire amplifier network including Master Volume adjustment, Subwoofer Level control, Fader adjustment, Zone Level management, and Preset Selection with commands automatically distributed to all networked amplifiers, centralized system management dramatically simplifying operation of complex multi-zone marine audio installations reducing multiple remote controllers to single unified control interface, professional installation accessory essential for advanced marine audio systems utilizing multiple MVI amplifiers across helm, cabin, cockpit, tower, and multiple zones requiring coordinated control and configuration, compact dimensions (285mm width x 101mm height x 52mm depth / 11.21" x 3.98" x 2.05") enabling installation in equipment compartments or concealed locations, IPX2 water resistance rating protecting against vertically falling water drops and light moisture exposure when properly installed, 5V DC power input with low current draw minimizing electrical system impact, USB 2.0 port supporting software updates ensuring latest firmware and feature enhancements, NMEA 2000 port with Micro-C connector reserved for future development potential marine network integration, complete installation package including network hub and mounting hardware, three-year manufacturer warranty demonstrating JL Audio confidence in product reliability, compatible exclusively with JL Audio MVI Marine Amplifier series requiring MVi-HUB for multi-amplifier networking functionality, proven JL Audio marine audio engineering delivering professional-grade networking solution transforming complex multi-amplifier installations into unified easily-managed systems, and essential accessory for luxury yachts, large recreational vessels, multi-deck boats, and advanced marine audio installations utilizing multiple MVI amplifiers requiring centralized configuration, synchronized processing, and unified remote control across entire audio system. Product Overview JL Audio JLA-010-03342-00 MVi-HUB JLid communication and network bridge for MVI marine amplifiers enabling multi-amplifier system integration. Professional networking hub simplifying configuration and control of complex marine audio systems with multiple amplifiers. Unified TüN software configuration: MVi-HUB enables all networked MVI amplifiers to appear in single TüN software session. Configure entire multi-amplifier system from one unified interface eliminating need to connect separately to each amplifier. Set crossovers, equalization, time alignment, and DSP parameters across all amplifiers simultaneously. Dramatically simplifies system tuning and configuration compared to managing multiple individual amplifier sessions. Synchronized DSP preset management: Network synchronizes DSP presets across all connected amplifiers. Creating preset on one amplifier automatically distributes to entire network. Switching presets changes all amplifiers simultaneously ensuring coordinated system-wide audio processing. Enables different tuning profiles for various listening scenarios (cruising, docked, water sports) applied consistently across entire system with single command. Distributed Digital Remote Controller commands: Single optional Digital Remote Controller (M-DRC-50 or DRC-205 sold separately) controls entire amplifier network. Master Volume adjustments affect all amplifiers proportionally maintaining system balance. Subwoofer Level control adjusts subwoofer amplifiers across system. Fader control adjusts front/rear balance. Zone Level management controls individual zone amplifiers. Preset Selection switches all amplifiers simultaneously. Commands automatically distributed to all networked amplifiers eliminating need for multiple remote controllers. Centralized system management: Transforms complex multi-amplifier installation into unified easily-managed system. Single remote controller replaces multiple individual amplifier controls. Single TüN software session replaces separate amplifier configurations. Coordinated operation across all zones and amplifiers. Simplified user experience for complex installations. Essential for advanced marine audio systems: Large vessels with multiple zones (helm, cabin, cockpit, flybridge, tower) powered by separate MVI amplifiers benefit from centralized control and configuration. Luxury yacht installations with comprehensive audio coverage. Multi-deck vessels requiring coordinated audio throughout. Professional marine audio installations demanding sophisticated system integration. Compact installation: Dimensions (285mm x 101mm x 52mm) enable mounting in equipment compartments, behind helm panels, or concealed locations. IPX2 water resistance protects against light moisture exposure when properly installed. 5V DC power input with minimal current draw. Low-profile design facilitating integration into existing equipment layouts. USB software updates: USB 2.0 port supports firmware updates ensuring latest features and improvements. Maintain system with current software releases. NMEA 2000 port reserved for future development potential marine network integration (currently not used). Compatible exclusively with JL Audio MVI Marine Amplifier series. MVi-HUB required for multi-amplifier MVI system networking. Single MVI amplifier installations do not require MVi-HUB. Multiple MVI amplifiers benefit significantly from MVi-HUB integration enabling unified control and configuration. Installation includes network hub and two mounting screws. Professional marine audio installation recommended for optimal system integration and configuration. Three-year manufacturer warranty. Typical system configurations: three MVI amplifiers (cabin speakers, tower speakers, subwoofers) networked via MVi-HUB with single DRC controlling entire system. Four MVI amplifiers (helm zone, cockpit zone, cabin zone, subwoofer) unified through MVi-HUB. Custom multi-zone layouts with five or more MVI amplifiers coordinated by MVi-HUB creating comprehensive vessel-wide audio system with centralized management. Unified TüN Software Configuration - Enables all networked MVI amplifiers to appear in single TüN software session eliminating separate amplifier connections and providing unified configuration interface for entire multi-amplifier system dramatically simplifying tuning and setup. Synchronized DSP Preset Management - Network synchronizes DSP presets across all connected amplifiers enabling system-wide preset creation, distribution, and switching ensuring coordinated audio processing throughout entire vessel with single preset command. Distributed DRC Command Control - Single optional Digital Remote Controller (M-DRC-50 or DRC-205) controls entire amplifier network distributing Master Volume, Subwoofer Level, Fader, Zone Level, and Preset Selection commands to all networked amplifiers. Centralized System Management - Transforms complex multi-amplifier installations into unified easily-managed systems replacing multiple remote controllers and separate configurations with single coordinated control interface simplifying operation. Multi-Amplifier Network Integration - Professional networking hub essential for advanced marine audio systems utilizing multiple MVI amplifiers across helm, cabin, cockpit, flybridge, and tower zones requiring coordinated control and configuration. IPX2 Water Resistance - IPX2 water resistance rating protecting against vertically falling water drops and light moisture exposure when properly installed suitable for equipment compartment or protected helm installations. Compact Installation Design - Space-efficient dimensions (285mm x 101mm x 52mm / 11.21" x 3.98" x 2.05") enabling mounting in equipment compartments, behind helm panels, or concealed locations without requiring excessive installation space. USB Software Updates - USB 2.0 port supporting firmware updates ensuring latest features, improvements, and functionality enhancements maintaining system with current software releases throughout product lifespan. NMEA 2000 Future Development - Integrated NMEA 2000 port with Micro-C connector reserved for future development potential marine network integration expanding system capabilities with future firmware releases. MVI Amplifier Compatibility - Compatible exclusively with JL Audio MVI Marine Amplifier series providing verified integration and networking functionality specifically designed for MVI amplifier architecture and DSP capabilities. Low Power Consumption - 5V DC power input with minimal current draw reducing electrical system impact and enabling straightforward power supply integration without significant vessel electrical capacity requirements. Professional Installation Accessory - Essential component for luxury yacht installations, large recreational vessels, multi-deck boats, and advanced marine audio systems requiring sophisticated multi-amplifier integration and centralized control. Technical Specifications Specification Details Model MVi-HUB (JLid Communication and Network Bridge) Part Number JLA-010-03342-00 Brand JL Audio Product Type Communication Hub / Network Bridge Function Multi-amplifier system integration and control Dimensions (W x H x D) 285 x 101 x 52 mm (11.21" x 3.98" x 2.05") Water Resistance IPX2 (when properly installed) Power Input 5 VDC Software Updates USB 2.0 USB Ports 1 x USB 2.0 (software update only) NMEA 2000 Ports 1 (Micro-C connector, currently not used - future development) Compatible Amplifiers JL Audio MVI Marine Amplifiers TüN Software Integration Unified multi-amplifier session DRC Compatibility M-DRC-50, DRC-205 (sold separately) Distributed Commands Master Volume, Subwoofer Level, Fader, Zone Level, Preset Selection Warranty 3 years Included Accessories Network hub, 2 mounting screws Frequently Asked Questions Q: Do I need MVi-HUB for my MVI amplifier system? A: MVi-HUB required only for multi-amplifier MVI systems desiring unified control and configuration. Single MVI amplifier installations: MVi-HUB not necessary (amplifier operates independently with direct TüN connection and optional DRC). Two or more MVI amplifiers: MVi-HUB highly recommended enabling unified TüN software session, synchronized presets, and single DRC controlling entire network. Without MVi-HUB: each amplifier requires separate TüN configuration, individual DRC per amplifier, independent operation without coordination. Benefits increase with amplifier quantity—three or more MVI amplifiers benefit significantly from MVi-HUB simplifying complex system management. Q: How does MVi-HUB simplify multi-amplifier configuration? A: Without MVi-HUB: connect TüN software to each amplifier individually, configure crossovers/EQ/DSP separately per amplifier, manage multiple configuration files, coordinate settings manually across amplifiers. With MVi-HUB: connect TüN software once to MVi-HUB, all networked amplifiers appear in single unified session, configure entire system from one interface, changes propagate automatically, synchronized presets across all amplifiers. Example: setting crossover frequency affects relevant amplifiers simultaneously rather than requiring individual adjustment. System-wide EQ adjustments applied cohesively. Dramatically reduces configuration time and complexity for multi-amplifier installations. Q: What Digital Remote Controllers work with MVi-HUB? A: Compatible DRCs (sold separately): M-DRC-50 or DRC-205. Single DRC controls entire amplifier network when connected through MVi-HUB. DRC commands distributed automatically: Master Volume adjusts all amplifiers proportionally, Subwoofer Level controls subwoofer amplifiers, Fader adjusts front/rear balance, Zone Level manages individual zones, Preset Selection switches all amplifiers simultaneously. Functionality varies by DRC model (consult DRC documentation for specific features). Without MVi-HUB: each MVI amplifier requires individual DRC. With MVi-HUB: single DRC controls entire multi-amplifier system eliminating multiple remote controllers and providing unified user interface. Q: How many MVI amplifiers can MVi-HUB network together? A: Specific maximum amplifier quantity not specified in provided documentation. MVi-HUB designed for typical marine multi-amplifier installations (generally 2-6 amplifiers). Common configurations: 3 amplifiers (speakers, tower, subwoofer), 4 amplifiers (helm zone, cockpit zone, cabin zone, subwoofer), 5-6 amplifiers (comprehensive multi-zone luxury yacht systems). For installations requiring extensive amplifier quantities: consult JL Audio technical support verifying MVi-HUB capacity and proper system architecture. Professional marine audio installer can design optimal configuration ensuring MVi-HUB adequately supports intended amplifier quantity and system complexity. Q: What is IPX2 rating and where can I install MVi-HUB? A: IPX2 rating protects against vertically falling water drops up to 15° from vertical (light rain or dripping water). Not suitable for: direct spray exposure, splashing water, submersion, high-pressure water jets. Suitable for: protected equipment compartments, behind helm panels in enclosed areas, cabin installations with overhead protection, locations experiencing only light moisture or condensation. Installation requirements: mount in location protected from direct water exposure, ensure proper orientation preventing water pooling on unit, avoid areas subject to spray or splashing, verify adequate ventilation preventing heat buildup. Not suitable for exposed cockpit locations or areas with significant water exposure. Most marine equipment compartments provide adequate protection for IPX2-rated equipment when properly installed with appropriate drainage and ventilation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03104-00 MHD Marine Amplifier - 4 Channel Full-Range 24V Marine Amplifier Professional 24-volt marine amplification with IP67 protection — MHD 4-channel amplifier delivers 150 watts per channel with Class-D efficiency and advanced signal processing for commercial vessels, charter boats, and larger yachts operating 24V electrical systems across Australian waters. Product Overview The JL Audio MHD 4-channel marine amplifier delivers professional-grade audio amplification specifically engineered for 24-volt marine electrical systems with 150 watts RMS per channel at 4Ω impedance (300 watts bridged) and 600 watts total continuous power output. Designed with full IP67 dust and water ingress protection, this Class-D amplifier features variable high-pass and low-pass filters with selectable 12/24 dB per octave slopes, detented calibrated crossover controls, switchable 2-channel or 4-channel input modes, and optional HD-RLC remote level control compatibility. Operating across 22-29V DC voltage range with comprehensive thermal, overload, and short-circuit protection, the compact chassis (273mm x 199mm x 49mm) enables professional installation in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6 marine speakers, marine subwoofers, and enclosed tower systems, this amplifier serves commercial fishing vessels, charter boats, larger recreational yachts, and marine applications requiring robust 24-volt amplification with three-year warranty coverage. Features & Benefits 24-Volt Marine System Optimization: Specifically engineered for 24V DC electrical systems (22-29V operating range) common in commercial vessels, larger yachts, and professional marine applications, delivering consistent 150W x 4 RMS power output at both 4Ω and 2Ω loads across voltage fluctuations typical in marine environments. Complete IP67 Environmental Protection: Full dust and water ingress protection withstands direct saltwater spray, submersion during washdown, bilge water exposure, and harsh marine conditions without requiring additional protective enclosures, ensuring reliable operation in demanding Australian coastal and offshore environments with three-year warranty coverage. Advanced Class-D Efficiency: High-efficiency Class-D topology minimizes heat generation and power consumption while delivering maximum output capability, reducing strain on vessel electrical systems and enabling compact chassis design fitting tight installation spaces common in marine equipment compartments. Professional Signal Processing: Variable high-pass and low-pass filters with selectable 12/24 dB per octave slopes and 50-500 Hz frequency range enable precise speaker and subwoofer integration, while detented calibrated potentiometers provide accurate repeatable crossover settings for professional system tuning and multi-amplifier installations. Flexible Channel Configuration: Switchable 2-channel or 4-channel input modes with bridged output capability (300W x 2) accommodate diverse system architectures from simple stereo installations to complex multi-zone configurations, while buffered pass-through preamp outputs enable daisy-chaining multiple amplifiers for expanded systems. Remote Level Control Ready: Optional HD-RLC remote level control compatibility (2-channel or all-channels mode) provides convenient volume adjustment from helm, cockpit, or cabin positions without accessing amplifier controls in equipment compartments, simplifying operation during underway conditions. Technical Specs Specification Details Model MHD 4-Channel (24V System) Amplifier Class Class-D Channels 4-channel full-range Total Power Output 600W RMS continuous RMS Power @ 4Ω 150W x 4 (28.8V input, <1% THD) RMS Power @ 2Ω 150W x 4 (28.8V input, <1% THD) Bridged Power @ 4Ω 300W x 2 Operating Voltage 22-29V DC (24V systems) Physical Dimensions 273mm W x 199mm D x 49mm H (10.74" x 7.85" x 1.93") Weight Approximately 3.0 kg (6.6 lbs) Dust/Water Rating IP67 (full protection) Signal-to-Noise Ratio >110 dB below rated power (A-weighted) Damping Factor @ 4Ω >300 at 50 Hz Damping Factor @ 2Ω >150 at 50 Hz THD+N @ Rated Power <0.03% @ 4Ω Frequency Response 6 Hz - 30 kHz (+0, -1dB) Input Voltage Range Switchable: 200mV-2V RMS (low) or 800mV-8V RMS (high) Filter Modes (Ch 1-4) Off, Low-Pass, or High-Pass Filter Slopes Selectable 12/24 dB per octave Filter Frequency Range 50 Hz - 500 Hz Crossover Controls Detented calibrated potentiometers Channel Input Mode Switchable 2/4 channels Preamp Outputs Buffered pass-through with source selection Remote Level Control Optional HD-RLC (2 or all channels) Fuse Rating (24V) 25 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 150W RMS per speaker for high-output marine audio across commercial and recreational vessels. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers (8" and 10"), M6 marine thin-line subwoofers, M7 marine subwoofers running in bridged mode (300W x 2) for dedicated low-frequency reinforcement in multi-amplifier systems. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with 4-volt preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. Tower Speaker Systems: JL Audio VeX enclosed tower systems, M3/M6 enclosed tower speakers requiring high-power amplification for wakeboarding, water sports, and offshore entertainment with long cable runs to tower-mounted speakers. Installation Accessories: 24V marine-grade amplifier wiring kits (4-gauge minimum), 25A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, HD-RLC remote level control, waterproof RCA cables, sealed wire connectors for professional 24V system integration. Frequently Asked Questions Why would I need a 24-volt amplifier instead of 12-volt? 24-volt electrical systems are standard in larger commercial vessels, charter boats, and yachts over 40 feet requiring increased electrical capacity for house loads, navigation equipment, and multiple high-power accessories. The 24V MHD amplifier integrates directly with these vessel electrical systems without requiring voltage converters or dual-battery configurations. Can this amplifier be used in 12-volt systems? No, the 24V model (JLA-010-03104-00) is specifically engineered for 22-29V DC operation and cannot be used in 12V systems. JL Audio offers separate 12V MHD models for standard marine applications. Verify your vessel's electrical system voltage before purchasing. What's the advantage of IP67 rating over standard marine amplifiers? IP67 provides complete protection against dust ingress and submersion up to 1 meter for 30 minutes, exceeding typical marine "water-resistant" ratings. This enables installation in exposed locations, bilge areas, or equipment compartments subject to washdown without additional protective enclosures. Can I bridge all four channels to create two 600W outputs? No, bridging creates two channels at 300W each (600W total). Channels 1+2 bridge together and channels 3+4 bridge together, each delivering 300W RMS at 4Ω impedance. This configuration is ideal for powering two subwoofers or two high-power speaker pairs. Do I need the optional HD-RLC remote level control? The HD-RLC is optional but recommended for convenient volume adjustment from helm or cockpit positions without accessing amplifier controls in equipment compartments. It can control either 2 channels or all 4 channels simultaneously, depending on your preference and system configuration.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03103-00 MHD Marine Amplifier - 5 Channel Full-Range Marine System Amplifier Complete marine audio solution with integrated subwoofer power — MHD 5-channel amplifier delivers 100 watts per speaker plus 500-watt dedicated subwoofer channel with Class-D efficiency and IP67 protection for single-amplifier system installations across Australian offshore vessels. Product Overview The JL Audio MHD 5-channel marine amplifier delivers complete audio system amplification from single chassis with 100 watts RMS per channel across four main speaker outputs (75W @ 2Ω) plus dedicated 500-watt RMS subwoofer channel for total 900-watt continuous power output. Designed with full IP67 dust and water ingress protection, this Class-D amplifier features independent high-pass filters for main channels (50-500 Hz, 12/24 dB slopes) and low-pass filter for subwoofer channel with defeatable 30 Hz infrasonic protection. Operating across 11-14.5V DC voltage range with switchable 2/4/6 channel input modes, optional HD-RLC remote subwoofer level control, and buffered pass-through preamp outputs, the compact chassis (273mm x 199mm x 49mm) simplifies installation by eliminating need for multiple amplifiers in complete speaker-plus-subwoofer marine audio systems. Compatible with JL Audio MediaMaster source units, M3/M6 marine speakers, marine subwoofers, and enclosed tower systems, this single-amplifier solution serves recreational boats, fishing vessels, and center console applications requiring professional system integration with three-year warranty coverage. Features & Benefits Complete Single-Amplifier Solution: Integrated 4-channel speaker amplification (100W x 4 @ 4Ω) plus dedicated 500W monoblock subwoofer channel eliminates need for separate speaker and subwoofer amplifiers, simplifying installation, reducing equipment costs, and minimizing space requirements in helm consoles and equipment compartments. Dedicated Subwoofer Channel Architecture: Independent 500-watt monoblock subwoofer output with dedicated low-pass filter (50-500 Hz, 12/24 dB slopes), defeatable 30 Hz infrasonic protection, and HD-RLC remote level control compatibility enables precise bass management separate from main speaker channels optimizing low-frequency performance. Complete IP67 Environmental Protection: Full dust and water ingress protection withstands direct saltwater spray, submersion during washdown, bilge water exposure, and harsh marine conditions without requiring additional protective enclosures, ensuring reliable operation in demanding Australian coastal and offshore environments with three-year warranty coverage. Advanced Class-D Efficiency: High-efficiency Class-D topology delivers 900 watts total continuous output while minimizing heat generation and electrical system strain, reducing current draw from vessel batteries and enabling compact chassis design fitting tight installation spaces common in marine equipment compartments. Independent Channel Processing: Main channels (1-4) feature high-pass only filtering protecting speakers from damaging low frequencies, while subwoofer channel provides low-pass filtering with infrasonic protection, enabling optimal frequency distribution between full-range speakers and dedicated subwoofer without requiring external crossovers or processors. Flexible Input Configuration: Switchable 2/4/6 channel input modes accommodate stereo source units, multi-zone installations, or bi-amped configurations, while buffered pass-through preamp outputs enable daisy-chaining additional amplifiers for expanded systems requiring tower speakers, cabin zones, or additional subwoofers. Technical Specs Specification Details Model MHD 5-Channel (12V System) Amplifier Class Class-D Channels 5-channel (4 main + 1 subwoofer) Total Power Output 900W RMS continuous Main Channels @ 4Ω 100W x 4 (14.4V input, <1% THD) Main Channels @ 2Ω 75W x 4 (14.4V input, <1% THD) Subwoofer Channel @ 4Ω 500W x 1 (14.4V input, <1% THD) Subwoofer Channel @ 2Ω 500W x 1 (14.4V input, <1% THD) Operating Voltage 11-14.5V DC (12V systems) Physical Dimensions 273mm W x 199mm D x 49mm H (10.74" x 7.85" x 1.93") Weight 3.11 kg (6.85 lbs) Dust/Water Rating IP67 (full protection) Signal-to-Noise Ratio >108.5 dB below rated power (A-weighted) Damping Factor @ 4Ω >400 at 50 Hz Damping Factor @ 2Ω >200 at 50 Hz THD+N (Main Channels) <0.03% @ 4Ω THD+N (Sub Channel) <0.05% @ 4Ω Frequency Response (Main) 12 Hz - 28 kHz (+0, -1dB) Frequency Response (Sub) 12 Hz - 10 kHz (+0, -1dB) Input Voltage Range Switchable: 200mV-2V RMS (low) or 800mV-8V RMS (high) Main Channels Filter High-pass only (50-500 Hz, 12/24 dB) Subwoofer Filter Low-pass only (50-500 Hz, 12/24 dB) Infrasonic Filter 30 Hz, defeatable (subwoofer channel) Crossover Controls Detented calibrated potentiometers Channel Input Mode Switchable 2/4/6 channels Preamp Outputs Buffered pass-through Remote Level Control Optional HD-RLC (subwoofer channel only) Fuse Rating 60 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 75-100W RMS per speaker across four main channels for complete full-range reproduction. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers (8" and 10"), M6 marine thin-line subwoofers, M7 marine subwoofers receiving dedicated 500W RMS monoblock power from integrated subwoofer channel with optimized low-pass filtering and infrasonic protection. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo (MM55 and MM55-HR models), JL Audio marine receivers with 4-volt preamp outputs providing high-voltage signal transmission for optimal noise rejection and six-channel audio distribution. Tower Speaker Systems: JL Audio VeX enclosed tower systems, M3/M6 enclosed tower speakers powered from main channels or connected via pass-through preamp outputs to additional amplifiers for expanded multi-zone installations. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 60A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, HD-RLC remote subwoofer level control, waterproof RCA cables, sealed wire connectors for professional complete-system integration. Frequently Asked Questions Why choose a 5-channel amplifier instead of separate speaker and subwoofer amplifiers? The 5-channel design simplifies installation by consolidating all amplification into single chassis, reducing equipment costs, minimizing space requirements, eliminating redundant power/ground wiring, and providing matched amplification characteristics across entire audio system. Ideal for boats where space and simplicity are priorities. Can I use the main channels to power four speakers plus add more speakers later? Yes, the buffered pass-through preamp outputs enable connection of additional amplifiers for tower speakers, cabin zones, or expanded systems. The main four channels directly power your primary speaker set while preamp outputs feed signals to external amplifiers for system expansion. How does the subwoofer channel differ from bridged 4-channel amplifiers? The dedicated subwoofer channel provides true monoblock architecture with optimized low-frequency performance (12-10 kHz response), dedicated low-pass filtering, defeatable 30 Hz infrasonic protection, and independent remote level control—features unavailable in bridged 4-channel configurations delivering inferior subwoofer performance. What's the advantage of IP67 rating over standard marine amplifiers? IP67 provides complete protection against dust ingress and submersion up to 1 meter for 30 minutes, exceeding typical marine "water-resistant" ratings. This enables installation in exposed locations, bilge areas, or equipment compartments subject to washdown without additional protective enclosures. Can the HD-RLC remote control adjust both speaker and subwoofer levels? No, the HD-RLC on 5-channel models controls subwoofer level only, allowing convenient bass adjustment from helm or cockpit positions without affecting main speaker volumes. This is the most common use case—adjusting bass output without touching overall system volume.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03336-00 MVi Marine Amplifier - 2 Channel Full-Range Marine Amplifier Professional DSP-equipped marine amplification with advanced tuning capability — MVi 2-channel amplifier delivers 300 watts per channel with integrated digital signal processing and USB computer tuning for precision audio system optimization across Australian offshore vessels. Product Overview The JL Audio MVi 2-channel marine amplifier delivers professional-grade audio amplification with integrated digital signal processing featuring 300 watts RMS per channel at 2Ω impedance (180W @ 4Ω) and 600 watts bridged monoblock capability for total system power output. Designed with IPX2 water and dust ingress protection when mounted vertically with connections pointed downward, this Class-D amplifier features comprehensive DSP functionality including parametric equalization, time alignment, crossover control, and system tuning accessible via USB computer connectivity. Operating across 10-15V DC voltage range with advanced thermal management and compact chassis dimensions (285mm x 176mm x 52mm), the MVi enables professional installation in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6/M7 marine speakers, marine subwoofers, and MVi-HUB communication bridge for networked multi-amplifier systems, this amplifier serves recreational boats, fishing vessels, and performance marine audio installations requiring precision system tuning with three-year warranty coverage across Australian waters. Features & Benefits Integrated Digital Signal Processing: Comprehensive DSP functionality includes 8-band parametric EQ per channel, adjustable crossovers (high-pass/low-pass/band-pass), time alignment up to 10 milliseconds, phase control, and signal routing enabling precision acoustic tuning matching vessel-specific acoustics, speaker characteristics, and listening environment optimization impossible with analog amplifiers. USB Computer Tuning Interface: Included 6-foot USB A/B cable enables connection to Windows/Mac computers running JL Audio tuning software providing graphical interface for adjusting all DSP parameters, creating system presets, monitoring real-time signal levels, and storing custom configurations for professional system optimization and client demonstration capabilities. IPX2 Environmental Protection: Water and dust ingress protection (when mounted vertically with connections downward) withstands marine spray, humidity, and environmental exposure common in equipment compartments and helm console installations, ensuring reliable operation in demanding saltwater conditions without requiring additional protective enclosures across Australian coastal environments. High-Efficiency Class-D Topology: Advanced Class-D amplifier architecture delivers maximum power output while minimizing heat generation and electrical system strain, reducing current draw from vessel batteries and enabling compact chassis design fitting tight installation spaces common in marine equipment compartments with superior thermal management. Flexible Channel Configuration: 2-channel design delivers 300W x 2 RMS at 2Ω for powering two high-output speakers, or bridge to monoblock 600W @ 4Ω for dedicated subwoofer amplification, while wide input voltage range (250mV-16V RMS) accommodates diverse source unit preamp output levels ensuring optimal gain structure. MVi-HUB Network Compatibility: Optional MVi-HUB communication bridge enables networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management across multiple MVi amplifiers for complex multi-zone marine audio installations requiring professional integration capabilities. Technical Specs Specification Details Model MVi 2-Channel (600W Total) Amplifier Class Class-D Channels 2-channel full-range RMS Power @ 4Ω 180W x 2 (14.4V input, <1% THD) RMS Power @ 2Ω 300W x 2 (14.4V input, <1% THD) Bridged Power @ 4Ω 600W x 1 monoblock Total Power Output 600W RMS maximum Operating Voltage 10-15V DC Physical Dimensions 285mm W x 176mm D x 52mm H (11.20" x 6.93" x 2.05") Weight 2.27 kg (5.0 lbs) Water/Dust Rating IPX2 (vertical mount, connections downward) Signal-to-Noise Ratio 99 dB below rated power (A-weighted) Damping Factor @ 4Ω >100 at 50 Hz THD+N @ Rated Power <1% @ 2Ω per channel Frequency Response 12 Hz - 24 kHz (+0, -1dB) Input Voltage Range 250mV - 16V RMS DSP Features 8-band parametric EQ, crossovers, time alignment, phase control Tuning Interface USB computer connectivity Network Capability MVi-HUB compatible Fuse Rating 50 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Included Accessories USB cable, power connector, speaker harnesses, mounting hardware Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 180-300W RMS per speaker for high-output marine audio across recreational and performance vessels. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers (8" and 10"), M6 marine thin-line subwoofers, M7 marine subwoofers running in bridged monoblock mode (600W @ 4Ω) for dedicated low-frequency reinforcement. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. MVi-HUB Communication Bridge: JLid communication and network bridge (MVi-HUB) enabling networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management for complex installations. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 50A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, waterproof RCA cables, sealed wire connectors, laptop computer for DSP tuning and system optimization. Frequently Asked Questions What computer software is required to access the DSP tuning features? JL Audio provides free Windows and Mac compatible tuning software downloadable from their website. Connect the included USB cable between amplifier and computer to access comprehensive DSP controls including parametric EQ, crossovers, time alignment, and all system parameters through graphical user interface. Can I use this amplifier to power both speakers and a subwoofer? The 2-channel configuration is best suited for two full-range speakers (300W each) or one subwoofer in bridged mode (600W). For simultaneous speaker and subwoofer power, consider the MVi 5-channel model with dedicated channels for both applications in single chassis. What does IPX2 rating mean and how should I mount the amplifier? IPX2 protection guards against water drops falling at angles up to 15 degrees from vertical when amplifier is mounted vertically with connections pointed downward. This configuration allows water drainage away from connections while protecting against dripping water and condensation in equipment compartments. Do I need the MVi-HUB for basic operation or is it only for multi-amplifier systems? The MVi-HUB is optional and only required for networked multi-amplifier installations. Single MVi amplifiers operate independently with full DSP functionality via direct USB connection to computer for tuning. MVi-HUB adds centralized control and system-wide coordination for complex multi-zone systems. How does the DSP functionality compare to external processors? Integrated DSP eliminates need for external signal processors, providing 8-band parametric EQ, adjustable crossovers, time alignment, and phase control built into amplifier. This simplifies installation, reduces component count, and ensures optimal signal path without additional converters or processors degrading audio quality.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03337-00 MVi Marine Amplifier - 4 Channel Full-Range Marine Amplifier Professional DSP-equipped marine amplification with advanced tuning capability — MVi 4-channel amplifier delivers 100 watts per channel with integrated digital signal processing and USB computer tuning for precision audio system optimization across Australian offshore vessels. Product Overview The JL Audio MVi 4-channel marine amplifier delivers professional-grade audio amplification with integrated digital signal processing featuring 100 watts RMS per channel at 2Ω impedance (75W @ 4Ω) and 200 watts bridged capability per pair for total 400-watt system power output. Designed with IPX2 water and dust ingress protection when mounted vertically with connections pointed downward, this Class-D amplifier features comprehensive DSP functionality including parametric equalization, time alignment, crossover control, and system tuning accessible via USB computer connectivity. Operating across 10-15V DC voltage range with advanced thermal management and compact chassis dimensions (285mm x 176mm x 52mm), the MVi enables professional installation in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6/M7 marine speakers, marine subwoofers, and MVi-HUB communication bridge for networked multi-amplifier systems, this amplifier serves recreational boats, fishing vessels, and marine audio installations requiring four-speaker configuration or bi-amped two-speaker systems with three-year warranty coverage across Australian waters. Features & Benefits Integrated Digital Signal Processing: Comprehensive DSP functionality includes 8-band parametric EQ per channel, adjustable crossovers (high-pass/low-pass/band-pass), time alignment up to 10 milliseconds, phase control, and signal routing enabling precision acoustic tuning matching vessel-specific acoustics, speaker characteristics, and listening environment optimization impossible with analog amplifiers. Four-Channel Versatility: 4-channel architecture delivers 100W x 4 RMS at 2Ω for powering four independent speakers, or bridge pairs to 200W x 2 @ 4Ω for bi-amped speaker systems or dedicated midbass/subwoofer applications, providing flexible system configurations from simple four-speaker stereo to complex bi-amplified installations with DSP optimization per channel. USB Computer Tuning Interface: Included 6-foot USB A/B cable enables connection to Windows/Mac computers running JL Audio tuning software providing graphical interface for adjusting all DSP parameters, creating system presets, monitoring real-time signal levels, and storing custom configurations for professional system optimization and client demonstration capabilities. IPX2 Environmental Protection: Water and dust ingress protection (when mounted vertically with connections downward) withstands marine spray, humidity, and environmental exposure common in equipment compartments and helm console installations, ensuring reliable operation in demanding saltwater conditions without requiring additional protective enclosures across Australian coastal environments. High-Efficiency Class-D Topology: Advanced Class-D amplifier architecture delivers maximum power output while minimizing heat generation and electrical system strain, reducing current draw from vessel batteries (40A fuse rating) and enabling compact chassis design fitting tight installation spaces common in marine equipment compartments with superior thermal management. MVi-HUB Network Compatibility: Optional MVi-HUB communication bridge enables networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management across multiple MVi amplifiers for complex multi-zone marine audio installations requiring professional integration capabilities. Technical Specs Specification Details Model MVi 4-Channel (400W Total) Amplifier Class Class-D Channels 4-channel full-range RMS Power @ 4Ω 75W x 4 (14.4V input, <1% THD) RMS Power @ 2Ω 100W x 4 (14.4V input, <1% THD) Bridged Power @ 4Ω 200W x 2 (pairs bridged) Total Power Output 400W RMS maximum Operating Voltage 10-15V DC Physical Dimensions 285mm W x 176mm D x 52mm H (11.20" x 6.93" x 2.05") Weight 2.27 kg (5.0 lbs) Water/Dust Rating IPX2 (vertical mount, connections downward) Signal-to-Noise Ratio 99 dB below rated power (A-weighted) Damping Factor @ 4Ω >100 at 50 Hz THD+N @ Rated Power <1% @ 2Ω per channel Frequency Response 12 Hz - 24 kHz (+0, -1dB) Input Voltage Range 250mV - 16V RMS DSP Features 8-band parametric EQ, crossovers, time alignment, phase control Tuning Interface USB computer connectivity Network Capability MVi-HUB compatible Fuse Rating 40 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Included Accessories USB cable, power connector, speaker harnesses, mounting hardware Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 75-100W RMS per speaker across four channels for complete helm, cockpit, or tower speaker coverage. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers (8" and 10"), M6 marine thin-line subwoofers, M7 marine subwoofers running in bridged mode (200W x 2 @ 4Ω) for dual subwoofer configurations or bi-amped speaker/subwoofer systems. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. MVi-HUB Communication Bridge: JLid communication and network bridge (MVi-HUB) enabling networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management for complex installations. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 40A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, waterproof RCA cables, sealed wire connectors, laptop computer for DSP tuning and system optimization. Frequently Asked Questions What computer software is required to access the DSP tuning features? JL Audio provides free Windows and Mac compatible tuning software downloadable from their website. Connect the included USB cable between amplifier and computer to access comprehensive DSP controls including parametric EQ, crossovers, time alignment, and all system parameters through graphical user interface. Can I use this amplifier to power both speakers and subwoofers simultaneously? Yes, the 4-channel configuration enables flexible system designs including: four full-range speakers (100W each), two speakers plus one subwoofer (channels 3+4 bridged for 200W sub), or bi-amped two-speaker system (midbass and highs on separate channels per side). DSP enables independent tuning for each application. What does IPX2 rating mean and how should I mount the amplifier? IPX2 protection guards against water drops falling at angles up to 15 degrees from vertical when amplifier is mounted vertically with connections pointed downward. This configuration allows water drainage away from connections while protecting against dripping water and condensation in equipment compartments. Do I need the MVi-HUB for basic operation or is it only for multi-amplifier systems? The MVi-HUB is optional and only required for networked multi-amplifier installations. Single MVi amplifiers operate independently with full DSP functionality via direct USB connection to computer for tuning. MVi-HUB adds centralized control and system-wide coordination for complex multi-zone systems. How does the 4-channel compare to separate 2-channel amplifiers? The 4-channel MVi consolidates all amplification into single chassis reducing installation complexity, equipment costs, power/ground wiring, and space requirements. Integrated DSP enables coordinated tuning across all channels impossible with separate amplifiers, while maintaining identical per-channel power output and audio quality specifications.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03341-00 MVi Marine Amplifier - 5 Channel Marine System Amplifier Complete DSP-equipped marine audio solution with dedicated subwoofer power — MVi 5-channel amplifier delivers 100 watts per speaker plus 600-watt subwoofer channel with integrated digital signal processing and USB computer tuning for precision complete-system optimization across Australian offshore vessels. Product Overview The JL Audio MVi 5-channel marine amplifier delivers professional-grade complete audio system amplification with integrated digital signal processing featuring 100 watts RMS per channel across four main speaker outputs at 2Ω impedance (75W @ 4Ω) plus dedicated 600-watt RMS subwoofer channel at 2Ω (400W @ 4Ω) for total 1000-watt system power output. Designed with IPX2 water and dust ingress protection when mounted vertically with connections pointed downward, this Class-D amplifier features comprehensive DSP functionality including parametric equalization, time alignment, crossover control, and system tuning accessible via USB computer connectivity. Operating across 10-15V DC voltage range with advanced thermal management and chassis dimensions (355mm x 176mm x 52mm), the MVi enables professional single-amplifier complete system installation eliminating need for separate speaker and subwoofer amplifiers in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6/M7 marine speakers, marine subwoofers, and MVi-HUB communication bridge for networked multi-amplifier systems, this amplifier serves recreational boats, fishing vessels, and performance marine audio installations requiring complete four-speaker-plus-subwoofer configuration with three-year warranty coverage across Australian waters. Features & Benefits Complete Single-Amplifier Solution: Integrated 4-channel speaker amplification (100W x 4 @ 2Ω) plus dedicated 600W monoblock subwoofer channel eliminates need for separate speaker and subwoofer amplifiers, simplifying installation, reducing equipment costs, minimizing space requirements, and consolidating power/ground wiring in helm consoles and equipment compartments. High-Power Dedicated Subwoofer Channel: 600-watt RMS monoblock subwoofer output at 2Ω (400W @ 4Ω) with dedicated DSP including low-pass filtering, parametric EQ, phase control, and independent gain structure enables professional subwoofer integration with M6, M7, or multiple subwoofer configurations requiring high-output low-frequency reinforcement. Integrated Digital Signal Processing: Comprehensive DSP functionality includes 8-band parametric EQ per channel, adjustable crossovers (high-pass/low-pass/band-pass), time alignment up to 10 milliseconds, phase control, and signal routing enabling precision acoustic tuning matching vessel-specific acoustics, speaker characteristics, and complete system optimization impossible with analog amplifiers. USB Computer Tuning Interface: Included 6-foot USB A/B cable enables connection to Windows/Mac computers running JL Audio tuning software providing graphical interface for adjusting all DSP parameters across main and subwoofer channels, creating system presets, monitoring real-time signal levels, and storing custom configurations for professional system optimization. IPX2 Environmental Protection: Water and dust ingress protection (when mounted vertically with connections downward) withstands marine spray, humidity, and environmental exposure common in equipment compartments and helm console installations, ensuring reliable operation in demanding saltwater conditions without requiring additional protective enclosures across Australian coastal environments. MVi-HUB Network Compatibility: Optional MVi-HUB communication bridge enables networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management across multiple MVi amplifiers for complex multi-zone marine audio installations requiring professional integration capabilities beyond single-amplifier coverage. Technical Specs Specification Details Model MVi 5-Channel 1000W (4 main + 1 sub) Amplifier Class Class-D Channels 5-channel (4 main + 1 subwoofer) Main Channels @ 4Ω 75W x 4 (14.4V input, <1% THD) Main Channels @ 2Ω 100W x 4 (14.4V input, <1% THD) Subwoofer @ 4Ω 400W x 1 (14.4V input, <1% THD) Subwoofer @ 2Ω 600W x 1 (14.4V input, <1% THD) Total Power Output 1000W RMS maximum Operating Voltage 10-15V DC Physical Dimensions 355mm W x 176mm D x 52mm H (13.96" x 6.93" x 2.05") Weight 2.54 kg (5.6 lbs) Water/Dust Rating IPX2 (vertical mount, connections downward) Signal-to-Noise (Main) 99 dB below rated power (A-weighted) Signal-to-Noise (Sub) 99 dB below rated power (A-weighted) Damping Factor @ 4Ω >150 at 50 Hz THD+N @ Rated Power <1% @ 2Ω per channel Frequency Response (Main) 12 Hz - 24 kHz (+0, -1dB) Frequency Response (Sub) 12 Hz - 1 kHz (+0, -1dB) Input Voltage Range 250mV - 16V RMS DSP Features 8-band parametric EQ, crossovers, time alignment, phase control Tuning Interface USB computer connectivity Network Capability MVi-HUB compatible Fuse Rating 80 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Included Accessories USB cable, power connector, speaker harnesses, mounting hardware Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 75-100W RMS per speaker across four main channels for complete helm, cockpit, cabin, or tower speaker coverage. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers (8" and 10"), M6 marine thin-line subwoofers, M7 marine subwoofers receiving dedicated 400-600W RMS monoblock power from integrated subwoofer channel with optimized low-frequency DSP processing. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. MVi-HUB Communication Bridge: JLid communication and network bridge (MVi-HUB) enabling networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management for expanded installations beyond single 5-channel amplifier. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 80A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, waterproof RCA cables, sealed wire connectors, laptop computer for DSP tuning and system optimization. Frequently Asked Questions What computer software is required to access the DSP tuning features? JL Audio provides free Windows and Mac compatible tuning software downloadable from their website. Connect the included USB cable between amplifier and computer to access comprehensive DSP controls including parametric EQ, crossovers, time alignment, and all system parameters through graphical user interface for both main and subwoofer channels. What's the difference between the 700W and 1000W 5-channel MVi amplifiers? The 1000W model (JLA-010-03341-00) delivers 600W subwoofer power at 2Ω versus 180W on the 700W model, while main channel power remains identical (100W x 4 @ 2Ω). Choose 1000W for M7 marine subwoofers or high-output subwoofer applications requiring maximum bass capability. Can I use this amplifier without a subwoofer and just power four speakers? Yes, the main four channels operate independently. However, the 5-channel design is optimized for complete speaker-plus-subwoofer systems. If you don't need subwoofer amplification, the 4-channel MVi model offers better value while maintaining identical main channel power and DSP capabilities. What does IPX2 rating mean and how should I mount the amplifier? IPX2 protection guards against water drops falling at angles up to 15 degrees from vertical when amplifier is mounted vertically with connections pointed downward. This configuration allows water drainage away from connections while protecting against dripping water and condensation in equipment compartments. Do I need the MVi-HUB for basic operation or is it only for multi-amplifier systems? The MVi-HUB is optional and only required for networked multi-amplifier installations. Single MVi amplifiers operate independently with full DSP functionality via direct USB connection to computer for tuning. MVi-HUB adds centralized control for complex multi-zone systems requiring multiple amplifiers.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03340-00 MVi Marine Amplifier - 5 Channel Marine System Amplifier Complete DSP-equipped marine audio solution with integrated subwoofer power — MVi 5-channel amplifier delivers 100 watts per speaker plus 180-watt subwoofer channel with integrated digital signal processing and USB computer tuning for precision complete-system optimization across Australian offshore vessels. Product Overview The JL Audio MVi 5-channel marine amplifier delivers professional-grade complete audio system amplification with integrated digital signal processing featuring 100 watts RMS per channel across four main speaker outputs at 2Ω impedance (75W @ 4Ω) plus dedicated 180-watt RMS subwoofer channel at 2Ω (180W @ 4Ω) for total 700-watt system power output. Designed with IPX2 water and dust ingress protection when mounted vertically with connections pointed downward, this Class-D amplifier features comprehensive DSP functionality including parametric equalization, time alignment, crossover control, and system tuning accessible via USB computer connectivity. Operating across 10-15V DC voltage range with advanced thermal management and chassis dimensions (355mm x 176mm x 52mm), the MVi enables professional single-amplifier complete system installation eliminating need for separate speaker and subwoofer amplifiers in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6 marine speakers, marine subwoofers, and MVi-HUB communication bridge for networked multi-amplifier systems, this amplifier serves recreational boats, fishing vessels, and marine audio installations requiring complete four-speaker-plus-subwoofer configuration with three-year warranty coverage across Australian waters. Features & Benefits Complete Single-Amplifier Solution: Integrated 4-channel speaker amplification (100W x 4 @ 2Ω) plus dedicated 180W monoblock subwoofer channel eliminates need for separate speaker and subwoofer amplifiers, simplifying installation, reducing equipment costs, minimizing space requirements, and consolidating power/ground wiring in helm consoles and equipment compartments. Dedicated Subwoofer Channel Architecture: 180-watt RMS monoblock subwoofer output at 2Ω/4Ω with dedicated DSP including low-pass filtering, parametric EQ, phase control, and independent gain structure enables professional subwoofer integration with M3, M6 8" subwoofers, or single subwoofer configurations requiring moderate bass reinforcement. Integrated Digital Signal Processing: Comprehensive DSP functionality includes 8-band parametric EQ per channel, adjustable crossovers (high-pass/low-pass/band-pass), time alignment up to 10 milliseconds, phase control, and signal routing enabling precision acoustic tuning matching vessel-specific acoustics, speaker characteristics, and complete system optimization impossible with analog amplifiers. USB Computer Tuning Interface: Included 6-foot USB A/B cable enables connection to Windows/Mac computers running JL Audio tuning software providing graphical interface for adjusting all DSP parameters across main and subwoofer channels, creating system presets, monitoring real-time signal levels, and storing custom configurations for professional system optimization. IPX2 Environmental Protection: Water and dust ingress protection (when mounted vertically with connections downward) withstands marine spray, humidity, and environmental exposure common in equipment compartments and helm console installations, ensuring reliable operation in demanding saltwater conditions without requiring additional protective enclosures across Australian coastal environments. MVi-HUB Network Compatibility: Optional MVi-HUB communication bridge enables networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management across multiple MVi amplifiers for complex multi-zone marine audio installations requiring professional integration capabilities beyond single-amplifier coverage. Technical Specs Specification Details Model MVi 5-Channel 700W (4 main + 1 sub) Amplifier Class Class-D Channels 5-channel (4 main + 1 subwoofer) Main Channels @ 4Ω 75W x 4 (14.4V input, <1% THD) Main Channels @ 2Ω 100W x 4 (14.4V input, <1% THD) Subwoofer @ 4Ω 180W x 1 (14.4V input, <1% THD) Subwoofer @ 2Ω 180W x 1 (14.4V input, <1% THD) Total Power Output 700W RMS maximum Operating Voltage 10-15V DC Physical Dimensions 355mm W x 176mm D x 52mm H (13.96" x 6.93" x 2.05") Weight 2.54 kg (5.6 lbs) Water/Dust Rating IPX2 (vertical mount, connections downward) Signal-to-Noise (Main) 99 dB below rated power (A-weighted) Signal-to-Noise (Sub) 99 dB below rated power (A-weighted) Damping Factor @ 4Ω >150 at 50 Hz THD+N @ Rated Power <1% @ 2Ω per channel Frequency Response (Main) 12 Hz - 24 kHz (+0, -1dB) Frequency Response (Sub) 12 Hz - 1 kHz (+0, -1dB) Input Voltage Range 250mV - 16V RMS DSP Features 8-band parametric EQ, crossovers, time alignment, phase control Tuning Interface USB computer connectivity Network Capability MVi-HUB compatible Fuse Rating 60 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Included Accessories USB cable, power connector, speaker harnesses, mounting hardware Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 75-100W RMS per speaker across four main channels for complete helm, cockpit, cabin, or tower speaker coverage. JL Audio Marine Subwoofers: M3 marine subwoofers (8"), M6 marine subwoofers (8"), M6 marine thin-line subwoofers receiving dedicated 180W RMS monoblock power from integrated subwoofer channel with optimized low-frequency DSP processing for moderate bass reinforcement applications. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. MVi-HUB Communication Bridge: JLid communication and network bridge (MVi-HUB) enabling networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management for expanded installations beyond single 5-channel amplifier. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 60A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, waterproof RCA cables, sealed wire connectors, laptop computer for DSP tuning and system optimization. Frequently Asked Questions What computer software is required to access the DSP tuning features? JL Audio provides free Windows and Mac compatible tuning software downloadable from their website. Connect the included USB cable between amplifier and computer to access comprehensive DSP controls including parametric EQ, crossovers, time alignment, and all system parameters through graphical user interface for both main and subwoofer channels. What's the difference between the 700W and 1000W 5-channel MVi amplifiers? The 700W model (JLA-010-03340-00) delivers 180W subwoofer power versus 600W on the 1000W model, while main channel power remains identical (100W x 4 @ 2Ω). Choose 700W for M3 or single 8" M6 subwoofers requiring moderate bass output, or 1000W for M7 subwoofers or high-output bass applications. Can I use this amplifier without a subwoofer and just power four speakers? Yes, the main four channels operate independently. However, the 5-channel design is optimized for complete speaker-plus-subwoofer systems. If you don't need subwoofer amplification, the 4-channel MVi model offers better value while maintaining identical main channel power and DSP capabilities. What does IPX2 rating mean and how should I mount the amplifier? IPX2 protection guards against water drops falling at angles up to 15 degrees from vertical when amplifier is mounted vertically with connections pointed downward. This configuration allows water drainage away from connections while protecting against dripping water and condensation in equipment compartments. Do I need the MVi-HUB for basic operation or is it only for multi-amplifier systems? The MVi-HUB is optional and only required for networked multi-amplifier installations. Single MVi amplifiers operate independently with full DSP functionality via direct USB connection to computer for tuning. MVi-HUB adds centralized control for complex multi-zone systems requiring multiple amplifiers.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03338-00 MVi Marine Amplifier - 6 Channel Full-Range Car and Marine Amplifier Professional DSP-equipped multi-zone amplification with advanced tuning capability — MVi 6-channel amplifier delivers 100 watts per channel with integrated digital signal processing and USB computer tuning for precision six-speaker or three-zone audio system optimization across Australian offshore vessels. Product Overview The JL Audio MVi 6-channel marine amplifier delivers professional-grade audio amplification with integrated digital signal processing featuring 100 watts RMS per channel at 2Ω impedance (75W @ 4Ω) and 200 watts bridged capability per pair for total 600-watt system power output across six independent channels. Designed with IPX2 water and dust ingress protection when mounted vertically with connections pointed downward, this Class-D amplifier features comprehensive DSP functionality including parametric equalization, time alignment, crossover control, and system tuning accessible via USB computer connectivity. Operating across 10-15V DC voltage range with advanced thermal management and chassis dimensions (355mm x 176mm x 52mm), the MVi enables professional installation in equipment compartments, helm consoles, or below-deck locations. Compatible with JL Audio MediaMaster source units, M3/M6/M7 marine speakers, marine subwoofers, and MVi-HUB communication bridge for networked multi-amplifier systems, this amplifier serves recreational boats, fishing vessels, and marine audio installations requiring six-speaker configuration, three-zone audio distribution, or bi-amped three-speaker systems with three-year warranty coverage across Australian waters. Features & Benefits Six-Channel Versatility: 6-channel architecture delivers 100W x 6 RMS at 2Ω enabling diverse system configurations including six independent speakers for helm/cockpit/cabin/tower coverage, three-zone audio distribution (2 channels per zone), bi-amped three-speaker systems, or three bridged pairs at 200W each for high-power applications with DSP optimization per channel. Integrated Digital Signal Processing: Comprehensive DSP functionality includes 8-band parametric EQ per channel, adjustable crossovers (high-pass/low-pass/band-pass), time alignment up to 10 milliseconds, phase control, and signal routing enabling precision acoustic tuning matching vessel-specific acoustics, speaker characteristics, and multi-zone listening environment optimization impossible with analog amplifiers. Multi-Zone Audio Distribution: Six independent channels enable professional three-zone audio distribution with two channels per zone (helm, cockpit, cabin) featuring independent volume control, source selection, and DSP optimization per zone, simplifying complex marine audio installations requiring simultaneous different content across multiple vessel areas. USB Computer Tuning Interface: Included 6-foot USB A/B cable enables connection to Windows/Mac computers running JL Audio tuning software providing graphical interface for adjusting all DSP parameters, creating system presets, monitoring real-time signal levels, and storing custom configurations for professional system optimization across all six channels. IPX2 Environmental Protection: Water and dust ingress protection (when mounted vertically with connections downward) withstands marine spray, humidity, and environmental exposure common in equipment compartments and helm console installations, ensuring reliable operation in demanding saltwater conditions without requiring additional protective enclosures across Australian coastal environments. MVi-HUB Network Compatibility: Optional MVi-HUB communication bridge enables networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management across multiple MVi amplifiers for complex multi-zone marine audio installations requiring professional integration capabilities beyond single-amplifier coverage. Technical Specs Specification Details Model MVi 6-Channel (600W Total) Amplifier Class Class-D Channels 6-channel full-range RMS Power @ 4Ω 75W x 6 (14.4V input, <1% THD) RMS Power @ 2Ω 100W x 6 (14.4V input, <1% THD) Bridged Power @ 4Ω 200W x 3 (pairs bridged) Total Power Output 600W RMS maximum Operating Voltage 10-15V DC Physical Dimensions 355mm W x 176mm D x 52mm H (13.96" x 6.93" x 2.05") Weight 2.54 kg (5.6 lbs) Water/Dust Rating IPX2 (vertical mount, connections downward) Signal-to-Noise Ratio 99 dB below rated power (A-weighted) Damping Factor @ 4Ω >100 at 50 Hz THD+N @ Rated Power <1% @ 2Ω per channel Frequency Response 12 Hz - 24 kHz (+0, -1dB) Input Voltage Range 250mV - 16V RMS DSP Features 8-band parametric EQ, crossovers, time alignment, phase control Tuning Interface USB computer connectivity Network Capability MVi-HUB compatible Fuse Rating 50 amps Recommended Fuse Type AFS, AGU, or MaxiFuse Power Wire Gauge Minimum 4 AWG copper Included Accessories USB cable, power connector, speaker harnesses, mounting hardware Warranty 3 years manufacturer warranty Compatible With / Goes Well With JL Audio Marine Speakers: M3 marine speakers (6.5", 7.7", 8.8" coaxials), M6 marine speakers (6.5", 7.7", 8.8" coaxials), M3/M6 enclosed tower speakers receiving 75-100W RMS per speaker across six channels for comprehensive helm, cockpit, cabin, and tower speaker coverage. JL Audio Marine Subwoofers: M3 marine subwoofers, M6 marine subwoofers, M7 marine subwoofers running in bridged mode (200W x 3 @ 4Ω) for triple subwoofer configurations or bi-amped speaker/subwoofer systems across multiple zones. JL Audio Source Units: MediaMaster 105 marine stereo, MediaMaster 55 marine stereo, JL Audio marine receivers with multi-zone preamp outputs providing high-voltage signal transmission for optimal noise rejection and amplifier matching. MVi-HUB Communication Bridge: JLid communication and network bridge (MVi-HUB) enabling networked multi-amplifier systems with centralized control, coordinated DSP processing, and system-wide configuration management for complex installations. Installation Accessories: Marine-grade amplifier wiring kits (4-gauge minimum), 50A fuses (AFS/AGU/MaxiFuse), marine distribution blocks, waterproof RCA cables, sealed wire connectors, laptop computer for DSP tuning and system optimization. Frequently Asked Questions What computer software is required to access the DSP tuning features? JL Audio provides free Windows and Mac compatible tuning software downloadable from their website. Connect the included USB cable between amplifier and computer to access comprehensive DSP controls including parametric EQ, crossovers, time alignment, and all system parameters through graphical user interface across all six channels. Can I use this amplifier for three-zone audio distribution on my boat? Yes, the 6-channel configuration is ideal for three-zone systems with two channels per zone (helm, cockpit, cabin). Each zone can have independent DSP tuning, volume control, and speaker optimization. Use source unit zone outputs or MVi-HUB for advanced multi-zone control with different content per zone. How does the 6-channel compare to using two separate amplifiers? The 6-channel MVi consolidates all amplification into single chassis reducing installation complexity, equipment costs, power/ground wiring, and space requirements. Integrated DSP enables coordinated tuning across all channels impossible with separate amplifiers, while maintaining identical per-channel power output and audio quality specifications. What does IPX2 rating mean and how should I mount the amplifier? IPX2 protection guards against water drops falling at angles up to 15 degrees from vertical when amplifier is mounted vertically with connections pointed downward. This configuration allows water drainage away from connections while protecting against dripping water and condensation in equipment compartments. Do I need the MVi-HUB for basic operation or is it only for multi-amplifier systems? The MVi-HUB is optional and only required for networked multi-amplifier installations or advanced multi-zone control with different sources per zone. Single MVi amplifiers operate independently with full DSP functionality via direct USB connection to computer for tuning. MVi-HUB adds centralized control for complex systems.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03339-00 MVi Marine Amplifier - 8 Channel Full-Range Marine Amplifier Premium marine amplification with intelligent DSP control and IPX2 weather protection for ultimate boat audio performance. Product Overview The JL Audio MVi 8-Channel Marine Amplifier (JLA-010-03339-00) represents the pinnacle of marine audio engineering, delivering 800 watts of clean, efficient Class D power across eight independent channels. Designed specifically for the demanding marine environment, this amplifier combines advanced digital signal processing with IPX2 weather protection to provide exceptional sound quality and reliability on the water. The compact chassis houses sophisticated circuitry that powers everything from full-range speakers to tower speakers, with bridging capability for added flexibility. With USB connectivity for advanced tuning via JL Audio's TüN software and compatibility with the JLid network bridge, the MVi system transforms marine audio into a fully integrated, professionally tuned sound system that thrives in harsh saltwater conditions. Features & Benefits The 8-channel MVi amplifier delivers 100 watts RMS per channel at 2 ohms (90W at 12.5V input), providing ample power for comprehensive marine audio systems including helm stations, cockpit zones, tower speakers, and cabin areas. The Class D design ensures maximum efficiency with minimal heat generation, critical for enclosed marine installations. Advanced digital signal processing through USB connectivity allows precise tuning of crossovers, equalization, time alignment, and output levels for each channel individually. The amplifier's bridging capability creates four 200-watt channels for driving larger speakers or dedicated zones. IPX2 water and dust rating protects against splashing and marine moisture when mounted vertically with connections downward. The compact footprint (13.96" x 2.05" x 6.93") simplifies installation in space-constrained marine environments. Marine-grade construction with conformal-coated circuit boards and corrosion-resistant hardware ensures long-term reliability in saltwater conditions. Technical Specifications Specification Details Model JLA-010-03339-00 MVi Marine Amplifier Configuration 8-Channel Full-Range Amplifier Class Class D Power @ 14.4V / 4Ω 75W RMS x 8 channels Power @ 14.4V / 2Ω 100W RMS x 8 channels Power @ 12.5V / 2Ω 90W RMS x 8 channels Bridged Power 200W x 4 @ 4Ω Total System Power 800 watts Frequency Response 12 Hz - 21 kHz (+0/-1dB) Signal-to-Noise Ratio 99 dB (analog inputs) THD+N @ Rated Power <1% @ 2Ω per channel Damping Factor >100 @ 4Ω, >50 @ 2Ω (50 Hz) Input Voltage Range 250 mV - 16V RMS (RCA) Operating Voltage 10-15 VDC Water/Dust Rating IPX2 (vertical mount) Fuse Rating 80A Recommended Fuse Type AFS, AGU, or MaxiFuse™ Min. Wire Gauge 4 AWG (power/ground) Dimensions (W x H x D) 355 x 52 x 176 mm (13.96" x 2.05" x 6.93") Weight 2.54 kg (5.6 lbs) Warranty 3 years Included Accessories Power connector, speaker harnesses, 6ft USB cable, RCA covers, mounting hardware, Allen wrenches Compatible With / Goes Well With JL Audio Marine Speakers: M3 Marine Speakers, M6 Marine Speakers, M3/M6/M7 Marine Subwoofers, M6 Thin-Line Subwoofers, M3/M6 Enclosed Tower Speakers, VeX Enclosed Systems JL Audio Source Units: MediaMaster 55 Stereo, MediaMaster 105 Stereo, JL Audio Receivers System Components: JLid Communication and Network Bridge (MVi-HUB) for multi-amplifier networking and advanced system control Installation Requirements: 4 AWG copper power and ground wiring, 80A fuse (AFS/AGU/MaxiFuse), vertical mounting location with downward-facing connections for IPX2 rating, PC/Mac with USB for TüN software tuning Frequently Asked Questions Can this amplifier run a complete 8-speaker marine audio system with tower speakers? Yes, the 8-channel configuration is ideal for comprehensive marine systems. Use channels 1-4 for helm/cockpit speakers, channels 5-8 for tower speakers or additional zones. Alternatively, bridge channels in pairs (creating four 200W channels) to power larger tower speakers while using remaining channels for cabin or transom areas. What makes the MVi series suitable for saltwater environments compared to standard car amplifiers? MVi amplifiers feature IPX2 water/dust rating, conformal-coated circuit boards that resist corrosion, marine-grade stainless steel hardware, and UV-resistant construction. The vertical mounting requirement ensures connections face downward, preventing water ingress. Standard car amplifiers lack these protections and will corrode rapidly in marine environments. Do I need the JLid hub to use this amplifier or can it operate standalone? The amplifier operates independently without the JLid hub. However, the hub (MVi-HUB) enables networking multiple MVi amplifiers, source switching between multiple head units, zone control, and advanced system management. For single-amplifier installations, connect directly via USB to a PC/Mac for tuning with JL Audio's TüN software. What's the advantage of Class D amplification in marine applications? Class D amplifiers achieve 80-90% efficiency compared to 50-60% for Class AB designs, generating significantly less heat. This is crucial for marine installations where amplifiers are often mounted in enclosed, poorly ventilated spaces. The reduced heat generation improves reliability, extends component lifespan, and eliminates the need for large heat sinks or external cooling fans. Can I bridge all eight channels to create four high-power outputs for larger speakers? Yes, bridging pairs of channels creates four bridged outputs delivering 200 watts each at 4 ohms. This configuration is perfect for powering four large tower speakers or four separate zones with high-output requirements. Bridge channels 1-2, 3-4, 5-6, and 7-8 by connecting positive to one channel and negative to the adjacent channel, ensuring 4-ohm minimum load per bridged pair.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

JL Audio JLA-010-03335-00 MVi Marine Amplifier - Monoblock Marine Subwoofer Amplifier High-output monoblock marine subwoofer amplifier with intelligent DSP control and IPX2 weather protection for powerful bass on the water. Product Overview The JL Audio MVi Monoblock Marine Amplifier (JLA-010-03335-00) delivers 1000 watts of dedicated subwoofer power designed specifically for the demanding marine environment. This Class D monoblock amplifier combines massive output capability with advanced digital signal processing to provide exceptional low-frequency performance and reliability on the water. The IPX2-rated chassis protects sophisticated circuitry from marine moisture and splashing, while USB connectivity enables precise tuning via JL Audio's TüN software. With frequency response optimized for subwoofer duty (12 Hz-500 Hz) and exceptional damping factor for tight bass control, this amplifier transforms marine audio systems by adding deep, powerful low-end response. Compatible with JL Audio's complete range of marine subwoofers including M3, M6, M6 Thin-Line, and M7 models, the MVi monoblock delivers the foundation for professional-grade boat audio that thrives in harsh saltwater conditions. Features & Benefits The 1000-watt monoblock configuration delivers 1000 watts RMS at 2 ohms (800W at 12.5V input) or 600 watts at 4 ohms, providing massive power for single or dual subwoofer installations. Class D amplification achieves maximum efficiency with minimal heat generation, essential for enclosed marine installations where ventilation is limited. Advanced digital signal processing through USB connectivity allows precise tuning of subsonic filters, low-pass crossovers, equalization, phase adjustment, and output levels specifically for your subwoofer and boat acoustics. The frequency response optimized for bass reproduction (12 Hz-500 Hz) ensures energy is focused where subwoofers need it most. Exceptional damping factor exceeding 400 at 4 ohms and 300 at 2 ohms provides tight control over subwoofer cone movement for articulate, punchy bass response. IPX2 water and dust rating protects against splashing and marine moisture when mounted vertically with connections downward. Marine-grade construction with conformal-coated circuit boards and corrosion-resistant stainless steel hardware ensures long-term reliability in saltwater environments. Technical Specifications Specification Details Model JLA-010-03335-00 MVi Marine Amplifier Configuration Monoblock Subwoofer Amplifier Amplifier Class Class D Power @ 14.4V / 4Ω 600W RMS x 1 channel Power @ 14.4V / 2Ω 1000W RMS x 1 channel Power @ 12.5V / 4Ω 500W RMS x 1 channel Power @ 12.5V / 2Ω 800W RMS x 1 channel Total System Power 1000 watts Frequency Response 12 Hz - 500 Hz (+0/-1dB) Signal-to-Noise Ratio 87 dB (analog inputs, rated power) SNR @ 1W 60 dB (analog inputs) THD+N @ Rated Power <1% @ 2Ω Damping Factor >400 @ 4Ω, >300 @ 2Ω (50 Hz) Input Voltage Range 250 mV - 8V RMS (RCA) Operating Voltage 10-15 VDC Water/Dust Rating IPX2 (vertical mount) Fuse Rating 80A Recommended Fuse Type AFS, AGU, or MaxiFuse™ Min. Wire Gauge 4 AWG (power/ground) Dimensions (W x H x D) 355 x 52 x 176 mm (13.96" x 2.05" x 6.93") Weight 2.54 kg (5.6 lbs) Warranty 3 years Included Accessories Power connector, speaker harnesses, 6ft USB cable, RCA covers, mounting hardware, Allen wrenches Compatible With / Goes Well With JL Audio Marine Subwoofers: M3 Marine Subwoofer, M6 Marine Subwoofer, M6 Marine Thin-Line Subwoofer, M7 Marine Subwoofer, VeX Enclosed System JL Audio Source Units: MediaMaster 55 Stereo, MediaMaster 105 Stereo, JL Audio Receivers for signal source and system integration System Components: JLid Communication and Network Bridge (MVi-HUB) for multi-amplifier networking, zone control, and advanced system management Installation Requirements: 4 AWG copper power and ground wiring, 80A fuse (AFS/AGU/MaxiFuse), vertical mounting location with downward-facing connections for IPX2 rating, PC/Mac with USB for TüN software tuning, sealed or ported subwoofer enclosure matched to amplifier power output Frequently Asked Questions Can this amplifier power two marine subwoofers simultaneously? Yes, you can wire two subwoofers to achieve the desired impedance load. Two 4-ohm subs wired in parallel create a 2-ohm load (1000W), two 2-ohm subs in series create 4 ohms (600W). For maximum output, use two 4-ohm subwoofers in parallel. Ensure your subwoofers can handle the divided power and that combined power handling exceeds amplifier output. What's the advantage of the 12 Hz-500 Hz frequency response for subwoofer applications? This optimized bandwidth focuses amplifier power exclusively in the bass region where subwoofers operate, eliminating wasted energy on frequencies the subwoofer cannot reproduce. The 12 Hz lower limit captures deep bass fundamentals often lost in marine environments, while the 500 Hz upper limit prevents overlap with full-range speakers, ensuring clean system integration and maximum efficiency. How does the damping factor affect subwoofer performance in a boat? The exceptional damping factor (>400 @ 4Ω) provides superior control over subwoofer cone movement, critical in marine environments where boat motion and acoustic reflections can cause bass to sound loose or boomy. High damping factor ensures the amplifier can rapidly stop and start cone movement, delivering tight, accurate bass response even when the boat is moving through water or encountering waves. Do I need the JLid hub for a single-amplifier, subwoofer-only system? No, the amplifier operates independently. Connect your source unit's subwoofer output via RCA cable and tune using a PC/Mac with USB connection and JL Audio's TüN software. The JLid hub becomes valuable when adding additional MVi amplifiers for full-range speakers, enabling unified system control, source switching, zone management, and simplified tuning across multiple amplifiers. Why choose a dedicated subwoofer amplifier over using bridged channels from a multi-channel amp? Dedicated monoblock amplifiers like the MVi 1000W provide higher continuous power, better thermal management, frequency response optimized for bass reproduction (not wasted on highs), and superior damping factor for subwoofer control. The focused design eliminates compromises inherent in multi-purpose amplifiers, delivering cleaner, more powerful bass with greater reliability in demanding marine installations where amplifiers often run near capacity during extended listening sessions.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less