6 Metres. Video Signal. ACC Power. Reverse Trigger. Everything a Reverse Camera Needs. Product Overview The DNA Automotive RVS106F is a 6 metre RCA video extension cable with male RCA plug on one end and female RCA socket on the other and two dedicated power wires running the full length. Unlike the single-wire RVS006F, the RVS106F includes both a red ACC wire for constant or switched power supply and a yellow reversing light wire for the 12V reverse trigger signal. This makes it the more complete solution for reverse camera installations where the camera requires both a power feed and an automatic trigger that activates the camera view when reverse gear is selected. With all three wires video, ACC, and reverse trigger in a single 6 metre cable run, the RVS106F simplifies installation by eliminating the need to run a separate trigger wire from the reversing lights to the headunit or camera controller. Route once, connect all three, and the camera switches on automatically every time reverse is selected. Key Specifications Part Number: RVS106F Brand: DNA Automotive Cable Type: RCA video extension with dual power wires Connector End 1: Male RCA plug Connector End 2: Female RCA socket Red Wire: ACC — constant or switched 12V power supply Yellow Wire: Car reversing light 12V — reverse trigger signal Cable Length: 6 metres Packaging: Blister & Card Cable Gauge (wires): Not specified — confirm with supplier Video Signal Type: Not specified — confirm with supplier Shielding: Not specified — confirm with supplier Features & Benefits Two power wires — ACC and reverse trigger in one run — The RVS106F includes both the red ACC wire (for camera power supply) and the yellow reversing light wire (for the 12V reverse trigger that switches the headunit or display to camera view). Running both wires alongside the video cable means a single 6 metre cable pass handles everything — no separate reverse trigger wire needed. Yellow reverse trigger wire — automatic camera activation — The yellow wire connects to the vehicle's 12V reversing light circuit. When reverse gear is selected and the reversing lights activate, the 12V signal travels back through the yellow wire to the headunit or camera controller, automatically switching the display to reverse camera view. This is how reverse cameras are designed to work — the trigger happens without any driver input. Red ACC wire — camera power supply — The red wire connects to a 12V ACC or constant power source to supply power to the camera. Running it alongside the video and trigger wires keeps all camera wiring in one neat cable run from the rear of the vehicle to the headunit. 6 metre length — standard reverse camera run — Six metres covers most ute, SUV, wagon, and van reverse camera installations from tow bar or tailgate camera mount to the headunit in the cabin. For longer-wheelbase vehicles or caravan tow camera setups, consider the RVS010F (10 metre, single power wire) or confirm whether a 10 metre dual-wire variant is available. Male to female RCA — extend or connect — The male-to-female configuration connects directly between a camera's male RCA output and a headunit's female RCA video input, or extends an existing RCA cable where more length is needed. Technical Specs Specification Detail Part Number RVS106F Brand DNA Automotive Cable Type RCA video extension with dual power wires Connector End 1 Male RCA plug Connector End 2 Female RCA socket Red Wire ACC — 12V power supply Yellow Wire Reversing light — 12V reverse trigger Cable Length 6 metres Wire Gauge Not specified — confirm with supplier Video Signal Not specified — confirm with supplier Shielding Not specified — confirm with supplier Packaging Blister & Card Compatible With / Goes Well With Typical Applications: Reverse camera installation — full cable run (video + power + trigger) Aftermarket reverse camera upgrade on any 12V vehicle Any installation where the camera requires separate ACC power and a 12V reversing light trigger Goes Well With: Reverse cameras with RCA video output and 12V power input Aftermarket headunits with RCA reverse camera input and reverse trigger wire DNA Automotive reverse cameras and driving aid accessories DNA RVS006F (single power wire — for cameras not requiring a separate reverse trigger) Frequently Asked Questions What is the difference between this cable and the RVS006F? The RVS106F includes two power wires — a red ACC wire for camera power and a yellow reversing light trigger wire. The RVS006F includes only a single power wire. Choose the RVS106F when your installation requires both a power feed and an automatic reverse trigger in the same cable run. What does the yellow wire connect to? The yellow wire connects to the 12V reversing light positive circuit in the vehicle. When reverse gear is selected and the reversing lights activate, the 12V signal travels through the yellow wire to the headunit or display, triggering automatic camera view. It carries a trigger signal — not a high-current power supply. What does the red wire connect to? The red wire connects to a 12V ACC or switched power source to supply power to the reverse camera. Connect it to an ACC circuit that is live when the ignition is on, or to a constant 12V source depending on your camera's requirements. Can I use this cable for a front-facing dash camera? This cable is designed for reverse camera installations — the yellow trigger wire is specific to the reversing light circuit. For a front-facing dash camera, a standard RCA extension or dedicated dash cam power cable is more appropriate. Is 6 metres enough for my vehicle? Six metres covers most standard ute, SUV, and wagon reverse camera installations. For longer-wheelbase vehicles, vans, or caravan tow camera setups, a longer cable run may be required. Measure your intended cable route before ordering.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10 Metres of Clean Video Signal RCA Male to Female with Power Wire. Product Overview The DNA Automotive RVS010F is a 10 metre RCA video extension cable with male RCA plug on one end, female RCA socket on the other, and a power wire running the full length. It is the longer sibling of the RVS006F designed for installations where 6 metres is not enough to reach from the camera or video source to the display or headunit. Ten metres covers longer-wheelbase vehicles, larger vans, bus conversions, motorhomes, and caravan-to-tow-vehicle camera runs that exceed the typical 6 metre requirement. As with the RVS006F, the included power wire runs the full cable length, allowing both video signal and camera power to be routed in a single pass through trims, panels, and under carpets keeping the installation tidy and reducing the number of individual cables run through the vehicle. Key Specifications Part Number: RVS010F Brand: DNA Automotive Cable Type: RCA video extension Connector End 1: Male RCA plug Connector End 2: Female RCA socket Includes: Power wire (full length) Cable Length: 10 metres Packaging: Blister & Card Cable Gauge (power wire): Not specified — confirm with supplier Video Signal Type: Not specified — confirm with supplier Shielding: Not specified — confirm with supplier Features & Benefits 10 metre length — for longer vehicle and tow camera runs — Where the 6 metre RVS006F falls short, the RVS010F picks up. Ten metres handles longer-wheelbase utes and vans, motorhomes, bus conversions, and caravan tow camera setups where the camera is mounted on the caravan or trailer and the cable must run back through a tow harness or along the vehicle to a cabin display. Male RCA to female RCA — extend or connect — The male-to-female configuration extends an existing RCA cable or connects directly between a camera's male RCA output and a headunit or monitor's female RCA input. Plug in, route, done. Power wire included — single cable run — The full-length power wire runs alongside the video cable, keeping both signal and camera power in one tidy run through door trims, headliners, and under-carpet routing. Fewer cables, cleaner installation. Purpose-built for rear camera and driving aid installations — The 10 metre length is specifically suited to applications where the camera is further from the display than a standard 6 metre cable can bridge — tow bars on long-wheelbase vehicles, caravan-mounted cameras, and extended cab or body van setups. Technical Specs Specification Detail Part Number RVS010F Brand DNA Automotive Cable Type RCA video extension Connector End 1 Male RCA plug Connector End 2 Female RCA socket Power Wire Included — full 10 metre length Cable Length 10 metres Power Wire Gauge Not specified — confirm with supplier Video Signal Not specified — confirm with supplier Shielding Not specified — confirm with supplier Packaging Blister & Card Compatible With / Goes Well With Typical Applications: Long-run reverse camera video signal extension Caravan and trailer tow camera video cable Motorhome and bus conversion rear camera runs Blind spot and side camera installations on larger vehicles Any 12V AV installation requiring a 10 metre RCA video run Goes Well With: Reverse cameras with RCA video output Aftermarket headunits with RCA video input Rear-view monitors with RCA input DNA RVS006F (6 metre version — for shorter runs) Frequently Asked Questions When should I choose the 10 metre cable over the 6 metre RVS006F? Choose the RVS010F when your camera-to-display run exceeds 6 metres — common in long-wheelbase utes, vans, motorhomes, and caravan tow camera setups where the camera is mounted further from the cabin than a 6 metre cable can reach. Can this cable extend an existing shorter RCA video cable? Yes. Connect the male RCA plug to the female socket of an existing cable and run the female socket end of the RVS010F to your headunit or display, adding 10 metres to the total cable run. Does the power wire run the full 10 metres? Yes — the power wire is included and runs the full 10 metre length, allowing both video signal and camera power to be routed together in a single cable pass through the vehicle. Is this cable suitable for a caravan or trailer tow camera? Yes — the 10 metre length is specifically suited to caravan and trailer camera setups where the camera is mounted at the rear of the trailer and the cable must run back through a connector or along the tow vehicle to reach the cabin display. Confirm the total cable run for your specific setup before ordering. What is the power wire gauge? Power wire gauge is not confirmed in the available product data. Contact us or refer to DNA Automotive's product documentation if wire gauge is a requirement for your installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

6 Metres of Clean Video Signal RCA Male to Female with Power Wire. Product Overview The DNA Automotive RVS006F is a 6 metre RCA video extension cable combining a male RCA plug on one end and a female RCA socket on the other, with an accompanying power wire running the full length. Designed for extending or connecting video signals in vehicle installations reverse cameras, dash cameras, headrest screens, and other 12V AV setups it provides the cable run needed to reach from the camera or source to the display or headunit without splicing or joining shorter cables. The included power wire alongside the video cable simplifies installation in a single cable run both signal and power travel together, keeping the wiring tidy and reducing the number of cables run through door trims, under carpets, and along the headliner. Key Specifications Part Number: RVS006F Brand: DNA Automotive Cable Type: RCA video extension Connector End 1: Male RCA plug Connector End 2: Female RCA socket Includes: Power wire (full length) Cable Length: 6 metres Packaging: Blister & Card Cable Gauge (power wire): Not specified — confirm with supplier Video Signal Type: Composite RCA (confirm with supplier) Shielding: Not specified — confirm with supplier Features & Benefits 6 metre length — reaches where shorter cables can't — At 6 metres, the RVS006F covers most vehicle installations from boot-mounted or tow bar cameras all the way to a headunit or display in the cabin — across utes, SUVs, vans, and caravans without needing to join multiple shorter cables. Male RCA to female RCA — extension or connection — The male-to-female configuration makes this cable suitable for both extending an existing RCA video cable (plug the male end into the female socket of the source cable and run the female end to the display) and for direct point-to-point connection between a male RCA camera output and a female RCA input on a headunit or monitor. Power wire included — single tidy cable run — The accompanying power wire runs the full 6 metres alongside the video cable, allowing both the camera power supply and video signal to be routed together in a single pass through trims and panels. Reduces installation time and cable clutter. Reverse camera and driving aid applications — Purpose-built length for running video signal from a reverse camera, blind spot camera, or tow camera at the rear of a vehicle to a headunit or monitor in the cabin — the primary use case for a 6 metre video cable in an automotive installation. Technical Specs Specification Detail Part Number RVS006F Brand DNA Automotive Cable Type RCA video extension Connector End 1 Male RCA plug Connector End 2 Female RCA socket Power Wire Included — full 6 metre length Cable Length 6 metres Power Wire Gauge Not specified — confirm with supplier Video Signal Not specified — confirm with supplier Shielding Not specified — confirm with supplier Packaging Blister & Card Compatible With / Goes Well With Typical Applications: Reverse camera video signal extension Dash camera video output extension Headrest screen and rear entertainment video feed Tow camera and blind spot camera installations Any 12V AV installation requiring a 6 metre RCA video run Goes Well With: Reverse cameras with RCA video output Aftermarket headunits with RCA video input Rear-view monitors and headrest screens with RCA input DNA Automotive and universal reverse camera accessories Frequently Asked Questions What is this cable used for? The RVS006F is used to extend or connect a composite RCA video signal in vehicle installations — most commonly running video from a rear-mounted reverse or tow camera to a headunit or display in the cabin. Can I use this cable to extend an existing shorter RCA cable? Yes. The male RCA plug connects to the female socket of an existing cable, and the female socket end connects to the display or headunit input, extending the total run by 6 metres. Does the power wire run the full 6 metres alongside the video cable? Yes — the power wire is included and runs the full 6 metres, allowing both video signal and camera power to be routed in a single cable pass through vehicle trims and panels. What is the gauge of the power wire? Power wire gauge is not confirmed in the available product data. Contact us or refer to DNA Automotive's product documentation if cable gauge is a requirement for your installation. Is this cable suitable for a caravan tow camera installation? Yes — at 6 metres, the RVS006F is well suited to tow camera setups where the camera is mounted at the rear of the tow vehicle or on the caravan and the video signal needs to reach a monitor in the cabin. Confirm the total cable run required for your specific tow vehicle and caravan combination before ordering.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Pop In. Wire Up. Factory Finish Square Socket Edition. Product Overview The DNA Automotive TOYSW04SL is a factory-fit SPST on/off switch designed to drop directly into the square blank switch socket found in compatible Toyota vehicles primarily the Prado 150 Series 2018-On and RAV4 2019-On, plus other Toyota models using the square switch format. Labelled "Starlink" to match the factory switch aesthetic, it replaces the square blanking insert with a functional 12VDC 3A switch with dual white LED illumination that lights up with the dash. No cutting, no drilling, no modification required. At 22mm H × 22mm W × 52mm D, the TOYSW04SL is purpose-built for the square factory blank socket a different fitment to the round-socket TOYSW03SL. The six-pin wiring configuration covers positive input, positive output, illumination positive, illumination earth, and chassis earth providing clean control of a relay-triggered accessory circuit with a professional, OEM-matched result. Key Specifications Part Number: TOYSW04SL Brand: DNA Automotive Switch Marking: Starlink Switch Type: SPST On/Off Voltage Rating: 12VDC Current Rating: 3A (positive switching only — inline fuse required, max 3A) Illumination: Dual white LED Colour: Black Dimensions: 22mm H × 22mm W × 52mm D Pin 1 (Black): Illumination Earth Pin 2 (Green): Positive Output — wire to relay Pin 3: Not used Pin 4 (White): Earth — wire to vehicle chassis Pin 5 (Red): Positive Input — wire to 12VDC positive (max 3A inline fuse required) Pin 6 (Yellow): Positive Input Illumination — wire to vehicle illumination positive Switching: Positive switching only Packaging: DNA Packaging Features & Benefits Direct factory square blank socket fitment — Designed to replace the square blank insert in compatible Toyota switch panels without any modification. Pop the blank out, plug the switch in. Maintains the factory finish with a professional, OEM-matched result — no aftermarket look, no panel gaps. SPST on/off with positive switching — Rated at 12VDC 3A for positive switching circuits. Wire Pin 2 (Positive Output) to the trigger terminal of a relay to control high-draw accessories — LED light bars, compressors, auxiliary lighting, lockers — keeping the switch within its 3A rating. An inline fuse rated to a maximum of 3A is required on the positive input (Pin 5). Dual white LED illumination — Pin 6 connects to the vehicle's illumination positive, with Pin 1 providing the illumination earth return. The switch face lights up with the dash — consistent illumination alongside factory Toyota switches on night drives. Six-pin wiring — clean, logical layout — The TOYSW04SL uses a six-pin configuration (top to bottom): illumination earth, positive output, positive input, and illumination positive. Four active pins cover all functions; Pin 3 is unused. The wiring is straightforward and fully documented. Starlink-labelled switch face — The "Starlink" label matches Toyota's connected multimedia system naming convention, integrating naturally into the factory Toyota switch panel for a purpose-built, cohesive appearance. Square socket — different from the TOYSW03SL — The TOYSW04SL fits the square factory blank socket (22mm H × 22mm W) used in newer Toyota platforms including the Prado 150 Series 2018-On and RAV4 2019-On. The TOYSW03SL fits the older round socket (32mm H × 20mm W). Confirm your vehicle's blank socket shape before ordering. OEM-matched black housing — Black finish blends with Toyota factory interiors across all listed platforms for a clean, consistent switch panel appearance. Technical Specs Specification Detail Part Number TOYSW04SL Switch Type SPST On/Off Voltage 12VDC Current Rating 3A Inline Fuse Required Yes — max 3A on Pin 5 positive input Switching Positive switching only Illumination Dual white LED Housing Colour Black Switch Marking Starlink Height 22mm Width 22mm Depth 52mm Pin 1 (Black) Illumination Earth Pin 2 (Green) Positive Output — to relay Pin 3 Not used Pin 4 (White) Earth — vehicle chassis Pin 5 (Red) Positive Input — 12VDC (max 3A inline fuse required) Pin 6 (Yellow) Positive Input Illumination Packaging DNA Packaging Compatible With / Goes Well With Confirmed Toyota Vehicles: Prado 150 Series 2018–On RAV4 2019–On Other Toyota vehicles using the square switch format (confirm socket dimensions — 22mm H × 22mm W — before purchase) Goes Well With: 12V relay (required for accessories drawing more than 3A) LED light bars, driving lights, auxiliary lighting (via relay) Air compressors, lockers, and other 12V accessories (via relay) 3A inline fuse (required on Pin 5 positive input) Frequently Asked Questions What is the difference between the TOYSW04SL and the TOYSW03SL? The TOYSW04SL fits the square factory blank socket (22mm H × 22mm W) used in newer Toyota vehicles including the Prado 150 2018-On and RAV4 2019-On. The TOYSW03SL fits the older round blank socket (32mm H × 20mm W). Confirm your socket shape before ordering. Does this switch require cutting or drilling to install? No. The TOYSW04SL pops directly into the square factory blank socket in compatible Toyota vehicles. Remove the existing blank insert and plug the switch in — no panel modification required. Is a fuse required and where does it go? Yes — a maximum 3A inline fuse is required on the positive input wire connected to Pin 5 (Red). Do not operate the switch without this fuse in line. What is the maximum load I can switch directly through this switch? The switch is rated at 12VDC 3A. For accessories drawing more than 3A, wire Pin 2 (Positive Output — Green) to the trigger of a relay rated for your accessory's current draw. The switch controls the relay, not the load. Do both illumination wires need to be connected for the switch to light up? Yes. The TOYSW04SL uses a two-wire illumination circuit — Pin 6 (Yellow) for illumination positive and Pin 1 (Black) for illumination earth. Both must be connected for the LED to illuminate. Connect Pin 6 to the vehicle illumination positive and Pin 1 to chassis earth.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

100W USB-C + 36W USB-A. Round Panel Mount. Laptop-Capable Vehicle Charging. Product Overview The PA100W is a universal round panel-mount vehicle charger combining a USB-C Power Delivery port at 100 watts and a USB-A Quick Charge port at 36 watts both running simultaneously from a 12V or 24V DC circuit. At 100W USB-C PD output, this charger delivers enough power to fast-charge a laptop, tablet, or any USB-C device rated up to 100W, including 20V 5A devices, directly from your vehicle's electrical system. The round mount design installs into a 29.2mm hole with a threaded locking nut for a secure, rattle-free fit in any dash panel, console, or custom build. A dust cover is included to protect the ports when not in use. Mounting depth is 59.9mm with a total depth from face to terminal of 78.2mm confirm clearance behind your mounting surface before installation. Designed for 4WDs, utes, vans, caravans, and any 12V or 24V vehicle where high-power USB charging is needed in a clean, panel-flush installation. Key Specifications SKU: PA100W Input Voltage: 12–24V DC USB-C Output: PD 100W — 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/5A USB-A Output: QC 36W — 5V/3A, 9V/3A, 12V/3A Maximum USB-C Output: 100W (20V at 5A) Maximum USB-A Output: 36W (12V at 3A) Mount Style: Universal round panel mount Mounting Hole Size: 29.2mm diameter Mounting Depth: 59.9mm Total Depth (face to terminal): 78.2mm Locking Nut: Yes — threaded Dust Cover: Yes — included Compatible Vehicles: Universal — any 12V or 24V DC vehicle Features & Benefits 100W USB-C PD — laptop-capable charging — At 20V 5A output, the USB-C port delivers true 100W Power Delivery — enough to charge a MacBook, Dell, HP, Lenovo, or any USB-C laptop at near-full speed from your vehicle. No more waiting for a hotel room or office outlet on the road — plug in your laptop on a long run through the outback and arrive with a charged machine. 36W USB-A Quick Charge — fast charge a second device simultaneously — The USB-A port supports Qualcomm Quick Charge profiles at 5V/3A, 9V/3A, and 12V/3A — fast-charging a smartphone, tablet, or USB-A accessory at the same time as the USB-C port is running at full 100W. Both ports operate independently. Universal round mount — fits any 29.2mm panel hole — The round mount design with threaded locking nut secures cleanly into any 29.2mm hole in a dash panel, centre console, armrest, or custom fabrication. No proprietary brackets, no adhesive mounts — drill a hole, drop it in, thread the nut from behind. Suits factory-drilled blanks in compatible vehicles or custom installs in caravans, 4WDs, utes, and vans. 12V and 24V compatible — works in any vehicle — From a standard 12V passenger car or 4WD through to a 24V truck, bus, or caravan setup, the PA100W accepts the full 12–24V DC input range without an adapter or voltage converter. One charger, any vehicle. Dust cover included — port protection when not in use — The included dust cover protects both ports from dust, moisture, and debris when the charger is not in use — important in off-road and dusty conditions where uncovered ports can fill with red dirt on a corrugated track. Threaded locking nut — secure, rattle-free fit — The threaded locking nut pulls the charger body tight against the mounting panel for a secure, rattle-free installation. No loosening over corrugations, no movement under vibration. Technical Specs Specification Detail SKU PA100W Input Voltage 12–24V DC USB-C Protocol Power Delivery (PD) USB-C Max Output 100W USB-C Output Profiles 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/5A USB-A Protocol Quick Charge (QC) USB-A Max Output 36W USB-A Output Profiles 5V/3A, 9V/3A, 12V/3A Mount Style Universal round panel mount Mounting Hole Diameter 29.2mm Mounting Depth 59.9mm Total Depth (face to terminal) 78.2mm Locking Nut Threaded — included Dust Cover Included Operating Voltage 12V or 24V DC Compatible With / Goes Well With Vehicles (universal — any 12V or 24V DC): 4WDs, utes, SUVs, and wagons Caravans and campervans Trucks and vans (12V and 24V) Boats and marine vessels Custom console and dash panel builds Devices: USB-C laptops (MacBook, Dell, HP, Lenovo, ASUS, and others rated up to 100W) USB-C tablets and iPads USB-C smartphones USB-A smartphones, tablets, and accessories (QC compatible) Any USB-PD or USB-QC compatible device within rated output Goes Well With: Panel-mount switch blanks and 29.2mm accessories Dual battery systems (12V or 24V) Vehicle-specific console and dash installation kits Frequently Asked Questions Can this charger power a laptop at full speed from my car? Yes — at 20V 5A (100W) USB-C PD output, the PA100W delivers enough power to charge most USB-C laptops at or near their maximum charge rate from any 12V or 24V vehicle circuit. Can I charge two devices at the same time? Yes. The USB-C and USB-A ports operate simultaneously — charge a laptop or tablet on USB-C while fast-charging a smartphone on USB-A QC at the same time. What size hole do I need to mount this charger? The PA100W requires a 29.2mm diameter mounting hole. Mounting depth behind the panel is 59.9mm, with a total depth from face to terminal of 78.2mm — confirm clearance behind your mounting surface before drilling. Does this charger work in both 12V and 24V vehicles? Yes. The PA100W accepts 12–24V DC input, making it compatible with standard 12V passenger vehicles, 4WDs, and caravans as well as 24V trucks, vans, and buses without any adapter or modification. Is a dust cover included? Yes — a dust cover is included in the box to protect both USB ports when not in use, keeping out dust, moisture, and debris during off-road driving or storage.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Pop In. Wire Up. Factory Finish. Product Overview The DNA Automotive TOYSW03SL is a factory-fit SPST on/off switch designed to drop directly into the small blank switch socket found in a wide range of Toyota vehicles and select 2018/2019 Mitsubishi models. Labelled "Starlink" to match the factory switch aesthetic, it replaces the standard blanking insert with a functional 12VDC 3A switch rated for positive switching, with dual white LED illumination that lights up with the dash. No cutting, no drilling, no modification pop the blank out, plug the switch in, run four wires, and you're done. At 32mm H × 20mm W × 52mm D, the TOYSW03SL matches the factory small blank socket dimensions across Hilux, Prado, Landcruiser 200 Series, Kluger, Fortuner, Corolla, Camry, RAV4, and Tundra applications. The black housing matches factory Toyota interiors for a clean, OEM-matched result that looks like it came from the dealership not the aftermarket parts bin. Key Specifications Part Number: TOYSW03SL Brand: DNA Automotive Switch Marking: Starlink Switch Type: SPST On/Off Voltage Rating: 12VDC Current Rating: 3A (positive switching only) Illumination: Dual white LED Colour: Black Dimensions: 32mm H × 20mm W × 52mm D Pin 1 (Green): Positive Input — wire to battery or ACC+ Pin 2 (Red): Positive Output — wire to relay Pin 3: Not used Pin 4 (Red): 12V Positive Illumination — connect to vehicle illumination circuit Pin 5 (Black): Earth — run to vehicle ground/chassis Packaging: DNA Blister & Card Features & Benefits Direct factory blank socket fitment — Designed to replace the small blank insert in compatible Toyota switch panels without any modification. Pop the blank out, plug the switch in. The result looks factory-fitted because it is factory-sized — essential for 4WD builds and touring setups where a professional, clean dashboard finish matters. SPST on/off with positive switching — Rated at 12VDC 3A for positive switching circuits. Wire Pin 2 to the trigger of a relay to control high-draw accessories — LED light bars, compressors, air horns, auxiliary lighting — keeping the switch within its 3A rating and protecting the circuit. Do not use as a direct load switch for accessories drawing more than 3A. Dual white LED illumination — Pin 4 connects to the vehicle's illumination positive so the switch lights up with the dash. On a night drive through the Pilbara or down the Nullarbor, your aux switches should look the part — the dual white LED delivers consistent, matched illumination alongside factory switches. Starlink-labelled switch face — The "Starlink" label matches Toyota's connected multimedia system naming convention, integrating naturally into Toyota switch panels. Purpose-built for setups where a dedicated Starlink function switch is required within the factory panel layout. OEM-matched black housing — Black finish matches Toyota factory interiors across all listed platforms. No colour mismatch, no aftermarket look — the switch sits flush and consistent with adjacent factory switches. DNA Blister & Card retail packaging — Retail-ready packaging with all specifications and wiring information on-pack for consumer purchase and shelf display. Technical Specs Specification Detail Part Number TOYSW03SL Switch Type SPST On/Off Voltage 12VDC Current Rating 3A Switching Positive switching only Illumination Dual white LED Illumination Input 12V positive (Pin 4) Housing Colour Black Switch Marking Starlink Height 32mm Width 20mm Depth 52mm Pin 1 (Green) Positive Input — Battery or ACC+ Pin 2 (Red) Positive Output — to relay Pin 3 Not used Pin 4 (Red) 12V Positive Illumination Pin 5 (Black) Earth / vehicle chassis ground Packaging DNA Blister & Card Compatible With / Goes Well With Confirmed Toyota Vehicles: Camry 2011–2014 Corolla 2006–2013 Fortuner 2015–On Hilux 2015–On Kluger 2007–On Landcruiser 200 Series 2016–On Prado 200 Series 2015–On Prado 150 Series 2010–2018 RAV4 2006–2011 Tundra 2007–2013 Also Suits: Most 2018/2019 Mitsubishi Pajero Most 2018/2019 Mitsubishi Triton Goes Well With: 12V relay (required for accessories drawing more than 3A) LED light bars, driving lights, auxiliary lighting (via relay) Air compressors, lockers, and other 12V accessories (via relay) Frequently Asked Questions Does this switch require cutting or drilling to install? No. The TOYSW03SL pops directly into the small factory blank socket in compatible Toyota vehicles. Remove the existing blank insert and plug the switch in — no panel modification required. What is the maximum load I can switch directly through this switch? The switch is rated at 12VDC 3A. For accessories drawing more than 3A, wire Pin 2 to the trigger terminal of an appropriately rated relay — the switch controls the relay, not the load directly. Which blank socket size does this switch fit? This switch fits the small factory blank socket, with dimensions of 32mm H × 20mm W × 52mm D. Toyota switch panels typically include both small and large blank sockets — confirm your available blank is the small size before ordering. Does the illumination wire have to be connected for the switch to work? No. Pin 4 (illumination positive) is optional — the on/off switching function operates independently. Connecting Pin 4 to the vehicle illumination circuit enables the switch face to light up with the dash lighting. Does this switch suit Mitsubishi vehicles as well as Toyota? Yes, it suits most 2018/2019 Mitsubishi Pajero and Triton models in addition to the listed Toyota vehicles. Verify that your Mitsubishi's blank socket dimensions match 32mm H × 20mm W × 52mm D before purchase, as compatibility is confirmed for most but not all variants.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 SW-1010A Next Gen Ford Ranger XL and XLS Switch Panel Insert Suits 10 Inch Screen A powder coated stainless mesh switch panel insert for the Next Gen Ford Ranger XL and XLS with a 10 inch touch screen, providing 4 aftermarket Toyota-style switch positions and a factory USB socket remount in a stylish clip-in panel. Installs in approximately 5 minutes. Proudly made in Australia by GMF4x4. Please note: This panel does NOT fit the XLT or Sport variants. See our separate listing for the XLT and Sport. For vehicles with a 12 inch touch screen (Raptor, Everest, or Wildtrak), please see our separate 12 inch listing. Product Overview The GMF4x4 SW-1010A is a stainless mesh switch panel insert designed specifically for the Next Gen Ford Ranger XL and XLS with a 10 inch touch screen. The quick clip-in design allows four aftermarket Toyota-style switches to be installed neatly alongside the factory USB socket, which is remounted within the panel for a clean, factory-style finish. The panel is powder coated black and installs in approximately 5 minutes with no drilling required. One stainless mesh panel and installation instructions are included. Please note this panel is designed exclusively for the XL and XLS variants with a 10 inch screen. It does not fit the XLT or Sport. Owners of Raptor, Everest, or Wildtrak models with a 12 inch screen should refer to our separate 12 inch listing. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. What's in the Box 1x Stainless Mesh Switch Panel 1x Installation Instructions Features & Benefits The clip-in design requires no drilling and installs in approximately 5 minutes, giving a clean and professional switch mounting solution without permanent modification to the vehicle. Four Toyota-style aftermarket switch positions allow accessories such as lights, lockers, air compressors, and other 12V accessories to be switched on and off from a single organised panel location. The factory USB socket is remounted within the panel, keeping the USB port accessible and integrating it into the new switch panel layout without losing factory functionality. The powder coated black finish and stainless mesh construction provide a durable, premium appearance that complements the Next Gen Ranger interior. Technical Specs Specification Detail SKU SW-1010A Brand GMF4x4 Compatible Vehicle Next Gen Ford Ranger XL and XLS Compatible Screen Size 10 Inch Touch Screen Not Compatible With Ford Ranger XLT, Sport (see separate listing) Not Compatible With Raptor, Everest, Wildtrak 12" screen (see separate listing) Switch Positions 4 x Toyota-Style Aftermarket Switch Positions Factory USB Yes, remounted within panel Panel Material Stainless Mesh Finish Powder Coated Black Mounting Method Clip-in Drilling Required No Installation Time Approx. 5 minutes Included 1x Stainless Mesh Panel, 1x Installation Instructions Origin Made in Australia Compatible With Next Gen Ford Ranger XL (10 inch touch screen) Next Gen Ford Ranger XLS (10 inch touch screen) Not compatible with Ford Ranger XLT, Sport, Raptor, Everest, or Wildtrak. Frequently Asked Questions Will this panel fit my Ranger XLT or Sport? No. The SW-1010A is designed exclusively for the Next Gen Ford Ranger XL and XLS with a 10 inch touch screen. It does not fit the XLT or Sport variants. Please see our separate listing for the XLT and Sport. I have a Raptor, Everest, or Wildtrak. Will this fit? No. The SW-1010A is for the 10 inch screen found in the XL and XLS. The Raptor, Everest, and Wildtrak use a 12 inch touch screen. Please see our separate 12 inch listing for those models. What type of switches fit this panel? The SW-1010A accommodates four Toyota-style aftermarket switches. Please check with us for compatible switch options if required. Does installation require drilling? No. The SW-1010A uses a quick clip-in design that installs in approximately 5 minutes without any drilling or permanent modification to the vehicle. Is this product made in Australia? Yes. GMF4x4 products are proudly designed and manufactured in Australia. GMF4x4 also hold designs, patents, and trademarks registered in Australia and internationally.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 SW-1010B Next Gen Ford Ranger XLT and Sport Switch Panel Insert Suits 10 Inch Screen A powder coated stainless mesh switch panel insert for the Next Gen Ford Ranger XLT and Sport with a 10 inch touch screen, providing 4 aftermarket Toyota-style switch positions and a factory USB socket remount in a stylish clip-in panel. Installs in approximately 5 minutes. Proudly made in Australia by GMF4x4. Please note: This panel does NOT fit the XL or XLS variants. See our separate listing for the XL and XLS. For vehicles with a 12 inch touch screen (Raptor, Everest, or Wildtrak), please see our separate 12 inch listing. Product Overview The GMF4x4 SW-1010B is a stainless mesh switch panel insert designed specifically for the Next Gen Ford Ranger XLT and Sport with a 10 inch touch screen. The quick clip-in design allows four aftermarket Toyota-style switches to be installed neatly alongside the factory USB socket, which is remounted within the panel for a clean, factory-style finish. The panel is powder coated black and installs in approximately 5 minutes with no drilling required. One stainless mesh panel and installation instructions are included. Please note this panel is designed exclusively for the XLT and Sport variants with a 10 inch screen. It does not fit the XL or XLS. Owners of Raptor, Everest, or Wildtrak models with a 12 inch screen should refer to our separate 12 inch listing. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. What's in the Box 1x Stainless Mesh Switch Panel 1x Installation Instructions Features & Benefits The clip-in design requires no drilling and installs in approximately 5 minutes, providing a clean and professional switch mounting solution without permanent modification to the vehicle. Four Toyota-style aftermarket switch positions allow accessories such as lights, lockers, air compressors, and other 12V accessories to be controlled from a single organised panel location. The factory USB socket is remounted within the panel, keeping the USB port accessible and integrating it into the new switch panel layout without losing factory functionality. The powder coated black finish and stainless mesh construction provide a durable, premium appearance that complements the Next Gen Ranger interior. Technical Specs Specification Detail SKU SW-1010B Brand GMF4x4 Compatible Vehicle Next Gen Ford Ranger XLT and Sport Compatible Screen Size 10 Inch Touch Screen Not Compatible With Ford Ranger XL, XLS (see separate listing) Not Compatible With Raptor, Everest, Wildtrak 12" screen (see separate listing) Switch Positions 4 x Toyota-Style Aftermarket Switch Positions Factory USB Yes, remounted within panel Panel Material Stainless Mesh Finish Powder Coated Black Mounting Method Clip-in Drilling Required No Installation Time Approx. 5 minutes Included 1x Stainless Mesh Panel, 1x Installation Instructions Origin Made in Australia Compatible With Next Gen Ford Ranger XLT (10 inch touch screen) Next Gen Ford Ranger Sport (10 inch touch screen) Not compatible with Ford Ranger XL, XLS, Raptor, Everest, or Wildtrak. Frequently Asked Questions Will this panel fit my Ranger XL or XLS? No. The SW-1010B is designed exclusively for the Next Gen Ford Ranger XLT and Sport with a 10 inch touch screen. It does not fit the XL or XLS variants. Please see our separate listing for the XL and XLS. I have a Raptor, Everest, or Wildtrak. Will this fit? No. The SW-1010B is for the 10 inch screen found in the XLT and Sport. The Raptor, Everest, and Wildtrak use a 12 inch touch screen. Please see our separate 12 inch listing for those models. What type of switches fit this panel? The SW-1010B accommodates four Toyota-style aftermarket switches. Please check with us for compatible switch options if required. Does installation require drilling? No. The SW-1010B uses a quick clip-in design that installs in approximately 5 minutes without any drilling or permanent modification to the vehicle. Is this product made in Australia? Yes. GMF4x4 products are proudly designed and manufactured in Australia. GMF4x4 also hold designs, patents, and trademarks registered in Australia and internationally.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 4003-PH-D Ford Everest RA 2022+ Phone and UHF Handpiece Holder A vehicle-specific powder coated black phone and UHF handpiece holder for the Ford Everest RA 2022+, designed and manufactured in Australia by GMF4x4 to be fully compliant with Australian Design Rules and airbag systems for safe, legal, and secure in-vehicle device mounting. Please allow a 2 week lead time on this product. Product Overview The GMF4x4 4003-PH-D is a purpose-built phone and UHF handpiece holder engineered specifically for the Ford Everest RA 2022+. Designed and manufactured in Australia, the bracket is fully compliant with Australian Design Rules (ADR) and airbag systems, providing peace of mind that your device mount meets Australian legal requirements and does not hinder the airbag system in the event of a collision. The bracket is powder coated black and designed for easy installation. Phone mounts are not included — GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads with this bracket. The 4003-PH-D is designed specifically for the Ford Everest RA 2022+ and cannot be transferred to another vehicle type. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. Features & Benefits Vehicle-specific design ensures the 4003-PH-D fits precisely within the Ford Everest RA 2022+ interior without interfering with vehicle controls, airbag zones, or occupant protection structures. Unlike universal window suction mounts, this bracket is securely mounted to the vehicle and engineered to withstand Australian heat, vibration, and the harsh conditions that cause suction and adhesive mounts to fail. Full ADR compliance and airbag system approval means the bracket meets Australian legal requirements for aftermarket accessories fitted to vehicles on Australian roads. GMF4x4's expertise in ADR compliance stems from over a decade of manufacturing ADR-compliant front and rear bars with full airbag approval and load testing. The hard-wearing powder coat black finish provides long-term chip and corrosion resistance. The holder keeps both a phone and a UHF handpiece within easy reach of the driver, optimally positioned for navigation visibility and communications access without distraction. Phone mounts are not included. GMF4x4 recommends Quadlock Wireless Charging Heads or MAG Heads for use with this bracket. Technical Specs Specification Detail SKU 4003-PH-D Brand GMF4x4 Compatible Vehicle Ford Everest RA 2022+ Finish Powder Coated Black Phone Mount Included No (Quadlock Wireless or MAG Head recommended) ADR Compliant Yes Airbag System Approved Yes Vehicle Transferable No (vehicle-specific design) Lead Time Approx. 2 weeks Origin Designed and Manufactured in Australia Compatible With Ford Everest RA 2022+ Quadlock Wireless Charging Heads (recommended, sold separately) Quadlock MAG Heads (recommended, sold separately) Frequently Asked Questions Why is a vehicle-specific phone mount safer than a suction cup or universal mount? Vehicle-specific brackets are securely mounted to the vehicle structure and engineered to withstand Australian heat, vibration, and temperature fluctuations that cause suction and adhesive mounts to fail. The 4003-PH-D is also ADR compliant and airbag approved, meaning it has been designed to not interfere with airbag deployment in the event of a collision, something universal window mounts cannot guarantee. Is this holder ADR compliant? Yes. The 4003-PH-D is fully compliant with Australian Design Rules and airbag system requirements. GMF4x4 has over a decade of experience in ADR compliance through the manufacture of ADR-compliant front and rear bars, and applies the same engineering standards to their phone holders. Are phone mounts included with this bracket? No. The 4003-PH-D is the vehicle-specific mounting bracket only. Phone mounts are not included. GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads, which are available separately. Can this bracket be used in other Ford Ranger or Raptor models? No. The 4003-PH-D is designed specifically for the Ford Everest RA 2022+ and cannot be transferred to another vehicle type. Please check our listings for specific holders designed for other Ranger and Raptor variants. Why is there a 2 week lead time on this product? The 4003-PH-D is made to order. Please allow approximately 2 weeks from order placement before dispatch.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 4004-PH-S Ford Ranger RA 2022+ Phone Holder A vehicle-specific powder coated black phone holder for the Ford Ranger RA 2022+, designed and manufactured in Australia by GMF4x4 to be fully compliant with Australian Design Rules and airbag systems for safe, legal, and secure in-vehicle phone mounting. Product Overview The GMF4x4 4004-PH-S is a purpose-built phone holder engineered specifically for the Ford Ranger RA 2022+. Designed and manufactured in Australia, the bracket is fully compliant with Australian Design Rules (ADR) and airbag systems, providing peace of mind that your device mount meets Australian legal requirements and does not hinder the airbag system in the event of a collision. The bracket is powder coated black and designed for easy installation. Phone mounts are not included — GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads with this bracket. The 4004-PH-S is designed specifically for the Ford Ranger RA 2022+ and cannot be transferred to another vehicle type. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. Features & Benefits Vehicle-specific design ensures the 4004-PH-S fits precisely within the Ford Ranger RA 2022+ interior without interfering with vehicle controls, airbag zones, or occupant protection structures. Unlike universal window suction mounts, this bracket is securely mounted to the vehicle and engineered to withstand Australian heat, vibration, and the harsh conditions that cause suction and adhesive mounts to fail. Full ADR compliance and airbag system approval means the bracket meets Australian legal requirements for aftermarket accessories fitted to vehicles on Australian roads. GMF4x4's expertise in ADR compliance stems from over a decade of manufacturing ADR-compliant front and rear bars with full airbag approval and load testing. The hard-wearing powder coat black finish provides long-term chip and corrosion resistance. The holder keeps your phone within easy reach of the driver, optimally positioned for navigation visibility without distraction. Phone mounts are not included. GMF4x4 recommends Quadlock Wireless Charging Heads or MAG Heads for use with this bracket. Technical Specs Specification Detail SKU 4004-PH-S Brand GMF4x4 Compatible Vehicle Ford Ranger RA 2022+ Finish Powder Coated Black Phone Mount Included No (Quadlock Wireless or MAG Head recommended) ADR Compliant Yes Airbag System Approved Yes Vehicle Transferable No (vehicle-specific design) Origin Designed and Manufactured in Australia Compatible With Ford Ranger RA 2022+ Quadlock Wireless Charging Heads (recommended, sold separately) Quadlock MAG Heads (recommended, sold separately) Frequently Asked Questions Why is a vehicle-specific phone mount safer than a suction cup or universal mount? Vehicle-specific brackets are securely mounted to the vehicle structure and engineered to withstand Australian heat, vibration, and temperature fluctuations that cause suction and adhesive mounts to fail. The 4004-PH-S is also ADR compliant and airbag approved, meaning it has been designed to not interfere with airbag deployment in the event of a collision, something universal window mounts cannot guarantee. Is this holder ADR compliant? Yes. The 4004-PH-S is fully compliant with Australian Design Rules and airbag system requirements. GMF4x4 has over a decade of experience in ADR compliance through the manufacture of ADR-compliant front and rear bars, and applies the same engineering standards to their phone holders. Are phone mounts included with this bracket? No. The 4004-PH-S is the vehicle-specific mounting bracket only. Phone mounts are not included. GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads, which are available separately. Can this bracket be used in other Ford Ranger variants or the Raptor? No. The 4004-PH-S is designed specifically for the Ford Ranger RA 2022+ and cannot be transferred to another vehicle type. Please check our listings for specific holders designed for other Ranger, Raptor, and Everest variants. Is this product made in Australia? Yes. GMF4x4 products are proudly designed and manufactured in Australia. GMF4x4 also hold designs, patents, and trademarks registered in Australia and internationally.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 4007-PH-D Toyota Hilux N70 2005-2014 Phone and UHF Handpiece Holder A vehicle-specific powder coated black phone and UHF handpiece holder for the Toyota Hilux N70 2005-2014, designed and manufactured in Australia by GMF4x4 to be fully compliant with Australian Design Rules and airbag systems for safe, legal, and secure in-vehicle device mounting. Product Overview The GMF4x4 4007-PH-D is a purpose-built phone and UHF handpiece holder engineered specifically for the Toyota Hilux N70 2005-2014. Designed and manufactured in Australia, the bracket is fully compliant with Australian Design Rules (ADR) and airbag systems, providing peace of mind that your device mount meets Australian legal requirements and does not hinder the airbag system in the event of a collision. The bracket is powder coated black and designed for easy installation. Phone mounts are not included — GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads with this bracket. The 4007-PH-D is designed specifically for the Toyota Hilux N70 2005-2014 and cannot be transferred to another vehicle type. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. Features & Benefits Vehicle-specific design ensures the 4007-PH-D fits precisely within the Toyota Hilux N70 interior without interfering with vehicle controls, airbag zones, or occupant protection structures. Unlike universal window suction mounts, this bracket is securely mounted to the vehicle and engineered to withstand Australian heat, vibration, and the harsh conditions that cause suction and adhesive mounts to fail. Full ADR compliance and airbag system approval means the bracket meets Australian legal requirements for aftermarket accessories fitted to vehicles on Australian roads. GMF4x4's expertise in ADR compliance stems from over a decade of manufacturing ADR-compliant front and rear bars with full airbag approval and load testing. The hard-wearing powder coat black finish provides long-term chip and corrosion resistance. The holder keeps both a phone and a UHF handpiece within easy reach of the driver, optimally positioned for navigation visibility and communications access without distraction. Phone mounts are not included. GMF4x4 recommends Quadlock Wireless Charging Heads or MAG Heads for use with this bracket. Technical Specs Specification Detail SKU 4007-PH-D Brand GMF4x4 Compatible Vehicle Toyota Hilux N70 2005-2014 Finish Powder Coated Black Phone Mount Included No (Quadlock Wireless or MAG Head recommended) ADR Compliant Yes Airbag System Approved Yes Vehicle Transferable No (vehicle-specific design) Origin Designed and Manufactured in Australia Compatible With Toyota Hilux N70 2005-2014 Quadlock Wireless Charging Heads (recommended, sold separately) Quadlock MAG Heads (recommended, sold separately) Frequently Asked Questions Why is a vehicle-specific phone mount safer than a suction cup or universal mount? Vehicle-specific brackets are securely mounted to the vehicle structure and engineered to withstand Australian heat, vibration, and temperature fluctuations that cause suction and adhesive mounts to fail. The 4007-PH-D is also ADR compliant and airbag approved, meaning it has been designed to not interfere with airbag deployment in the event of a collision, something universal window mounts cannot guarantee. Is this holder ADR compliant? Yes. The 4007-PH-D is fully compliant with Australian Design Rules and airbag system requirements. GMF4x4 has over a decade of experience in ADR compliance through the manufacture of ADR-compliant front and rear bars, and applies the same engineering standards to their phone holders. Are phone mounts included with this bracket? No. The 4007-PH-D is the vehicle-specific mounting bracket only. Phone mounts are not included. GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads, which are available separately. Can this bracket be used in other Toyota Hilux variants? No. The 4007-PH-D is designed specifically for the Toyota Hilux N70 2005-2014 and cannot be transferred to another vehicle type. Please check our listings for specific holders designed for other Hilux variants or Toyota models. Is this product made in Australia? Yes. GMF4x4 products are proudly designed and manufactured in Australia. GMF4x4 also hold designs, patents, and trademarks registered in Australia and internationally.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

GMF4x4 4009-PH-D Toyota Hilux N80 2015+ Phone and UHF Handpiece Holder A vehicle-specific powder coated black phone and UHF handpiece holder for the Toyota Hilux N80 2015+, designed and manufactured in Australia by GMF4x4 to be fully compliant with Australian Design Rules and airbag systems for safe, legal, and secure in-vehicle device mounting. Please note: Product photos are taken on a Hilux N80 without a UHF handpiece fitted. For an example of the UHF handpiece position, please refer to the additional Ranger photos included in the listing. Product Overview The GMF4x4 4009-PH-D is a purpose-built phone and UHF handpiece holder engineered specifically for the Toyota Hilux N80 2015+. Designed and manufactured in Australia, the bracket is fully compliant with Australian Design Rules (ADR) and airbag systems, providing peace of mind that your device mount meets Australian legal requirements and does not hinder the airbag system in the event of a collision. The bracket is powder coated black and designed for easy installation. Phone mounts are not included — GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads with this bracket. The 4009-PH-D is designed specifically for the Toyota Hilux N80 2015+ and cannot be transferred to another vehicle type. GMF4x4 have many designs, patents, and trademarks registered in Australia and internationally. Features & Benefits Vehicle-specific design ensures the 4009-PH-D fits precisely within the Toyota Hilux N80 interior without interfering with vehicle controls, airbag zones, or occupant protection structures. Unlike universal window suction mounts, this bracket is securely mounted to the vehicle and engineered to withstand Australian heat, vibration, and the harsh conditions that cause suction and adhesive mounts to fail. Full ADR compliance and airbag system approval means the bracket meets Australian legal requirements for aftermarket accessories fitted to vehicles on Australian roads. GMF4x4's expertise in ADR compliance stems from over a decade of manufacturing ADR-compliant front and rear bars with full airbag approval and load testing. The hard-wearing powder coat black finish provides long-term chip and corrosion resistance. The holder keeps both a phone and a UHF handpiece within easy reach of the driver, optimally positioned for navigation visibility and communications access without distraction. Phone mounts are not included. GMF4x4 recommends Quadlock Wireless Charging Heads or MAG Heads for use with this bracket. Technical Specs Specification Detail SKU 4009-PH-D Brand GMF4x4 Compatible Vehicle Toyota Hilux N80 2015+ Finish Powder Coated Black Phone Mount Included No (Quadlock Wireless or MAG Head recommended) ADR Compliant Yes Airbag System Approved Yes Vehicle Transferable No (vehicle-specific design) Origin Designed and Manufactured in Australia Compatible With Toyota Hilux N80 2015+ Quadlock Wireless Charging Heads (recommended, sold separately) Quadlock MAG Heads (recommended, sold separately) Frequently Asked Questions Why do the product photos not show a UHF handpiece? The prototype vehicle used during product photography was a Hilux N80 without a UHF handpiece fitted. For a visual example of how the UHF handpiece sits in the holder, please refer to the additional Ranger photos included in the listing images. Why is a vehicle-specific phone mount safer than a suction cup or universal mount? Vehicle-specific brackets are securely mounted to the vehicle structure and engineered to withstand Australian heat, vibration, and temperature fluctuations that cause suction and adhesive mounts to fail. The 4009-PH-D is also ADR compliant and airbag approved, meaning it has been designed to not interfere with airbag deployment in the event of a collision, something universal window mounts cannot guarantee. Is this holder ADR compliant? Yes. The 4009-PH-D is fully compliant with Australian Design Rules and airbag system requirements. GMF4x4 has over a decade of experience in ADR compliance through the manufacture of ADR-compliant front and rear bars, and applies the same engineering standards to their phone holders. Are phone mounts included with this bracket? No. The 4009-PH-D is the vehicle-specific mounting bracket only. Phone mounts are not included. GMF4x4 recommends using Quadlock Wireless Charging Heads or MAG Heads, which are available separately. Is this product made in Australia? Yes. GMF4x4 products are proudly designed and manufactured in Australia. GMF4x4 also hold designs, patents, and trademarks registered in Australia and internationally.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less