Stinger RKXDK Roadkill Expert Door Kit, 12 Sq Ft (6 Sheets) A purpose-matched Roadkill Expert door kit 6 sheets of butyl and aluminium sound damping material covering 12 sq ft. Sized to treat both front doors in a single purchase. Product Overview The Stinger RKXDK is a 6-sheet door-focused pack of Roadkill Expert sound damping material six sheets at 12" × 24" (approx. 30cm × 61cm each) for 12 sq ft of total coverage. It uses the same Roadkill Expert specification proprietary ultra-dense butyl blend bottom layer and 6 mil aluminium top layer as the RKX4 and RKX36B packs. The RKXDK is sized and marketed specifically for door treatment. At 12 sq ft it provides enough material to treat both front door inner skins in a typical vehicle the most common starting point for Roadkill installations, delivering the most noticeable improvement in speaker bass response and door rattle reduction. Self-adhesive, odourless, and non-toxic. Features & Benefits 6 sheets of Roadkill Expert — sized for front door treatment in a single kit 12 sq ft total coverage Proprietary ultra-dense butyl blend — kills panel resonance, squeaks, and rattles 6 mil aluminium outer layer — heat dissipation and structural integrity Self-adhesive — peel, press, and roll to apply Odourless and non-toxic Improves speaker bass response and audio output Application temperature range: –62°C to 149°C Technical Specs Specification Detail SKU / Part Number RKXDK Brand Stinger Series Roadkill Expert Coverage 12 sq ft — 6 sheets at 12" × 24" (approx. 30cm × 61cm each) Minimum Thickness 2.0mm (0.080 in) Aluminium Layer 6 mil Damping Weight 0.65 lbs/ft² Peel Adhesion Strength 40.89 lbs/in after 24 hours Application Temperature –62°C to 149°C (–80°F to 300°F) Adhesive Self-adhesive butyl layer Odour Odourless Toxicity Non-toxic Compatible With / Goes Well With Direct Vehicle Fit: Universal — suitable for any vehicle door inner skin and metal panel surfaces Goes Well With: Stinger RKFR6 Fast Rings (6.5" — for speaker mounting point treatment in the door) Stinger RKFR69 Fast Rings (6×9" — if applicable) Stinger RKX36B Roadkill Expert bulk kit (for extending treatment to floor, roof, and boot) Stinger RKCP12 Roadkill Carpet Foam Pad (for floor treatment under carpet) Stinger RKINSTALL sound deadener installation kit (roller and knife for application) Frequently Asked Questions Why is this called a "door kit" and how much does it cover? The RKXDK is sized to treat both front door inner skins in a typical vehicle — the most impactful area for Roadkill treatment. At 12 sq ft across 6 sheets, it provides enough material for comprehensive front door treatment in most small to medium vehicles. Is the material the same as the RKX4 and RKX36B? Yes. All three use the same Roadkill Expert specification — identical butyl blend, 6 mil aluminium layer, thickness, and adhesion rating. The RKXDK is simply a middle-ground pack size (12 sq ft) between the RKX4 trial pack (4 sq ft) and the RKX36B bulk kit (36 sq ft). How do I apply Roadkill Expert to a door? Remove the door card to access the inner metal skin. Clean the metal with wax and grease remover or methylated spirits and allow to dry. Cut sheets to shape, peel the backing, press firmly onto the door skin, and roll with the Stinger RKINSTALL roller for maximum adhesion. Pair with RKFR6 Fast Rings at the speaker mounting point for best results. Should I use Roadkill Fast Rings at the same time? Yes — strongly recommended. Treating the door inner skin with the RKXDK addresses panel resonance throughout the door, while the RKFR6 Fast Rings address the acoustic seal specifically around the speaker opening. Used together, the improvement in bass response and audio clarity is significantly greater than either product alone. Is the RKXDK sufficient for rear doors as well? The 12 sq ft coverage is typically sufficient for both front doors. For rear door treatment as well, an additional RKXDK or the larger RKX36B bulk pack is recommended. Contact the F.A.E. team for guidance on coverage requirements for your specific vehicle. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger RKX36B Roadkill Expert Bulk Kit, 36 Sq Ft (9 Sheets) The full-coverage Roadkill Expert option 9 sheets of proprietary butyl and aluminium sound damping material totalling 36 sq ft. Kills panel resonance, reduces road noise, improves bass response, and insulates the cabin. Product Overview The Stinger RKX36B is a bulk pack of Roadkill Expert sound damping material 9 sheets at 18" × 32" (approx. 46cm × 81cm each) for a total of 36 sq ft of coverage. Roadkill Expert uses a proprietary ultra-dense butyl blend bottom layer to absorb acoustic energy and a 6 mil aluminium top layer for heat dissipation and structural integrity. Applied to metal panel surfaces doors, roof, floor, firewall, boot it mass-loads the panels to reduce resonance, kills squeaks and rattles, improves speaker bass response, reduces low-frequency road noise, and helps regulate cabin temperature. Odourless, non-toxic, and self-adhesive. 36 sq ft covers a typical small to medium vehicle interior treatment including both front door inner skins and a floor or boot area. For larger vehicles or full interior treatment, multiple packs may be required. Features & Benefits 9 sheets of Roadkill Expert, 36 sq ft total coverage Proprietary ultra-dense butyl blend — absorbs acoustic energy, kills panel vibrations 6 mil aluminium outer layer — heat dissipation and structural integrity Self-adhesive — peel, press, and roll to apply Odourless and non-toxic Reduces road noise and driver fatigue Improves speaker bass response and overall sound quality Insulates cabin — more efficient HVAC in summer and winter Suitable for doors, roof, floor, firewall, boot, and any metal panel surface Application temperature range: –62°C to 149°C Technical Specs Specification Detail SKU / Part Number RKX36B Brand Stinger Series Roadkill Expert Coverage 36 sq ft — 9 sheets at 18" × 32" (approx. 46cm × 81cm each) Minimum Thickness 2.0mm (0.080 in) Aluminium Layer 6 mil Damping Weight 0.65 lbs/ft² Peel Adhesion Strength 40.89 lbs/in after 24 hours Application Temperature –62°C to 149°C (–80°F to 300°F) Adhesive Self-adhesive butyl layer Odour Odourless Toxicity Non-toxic Compatible With / Goes Well With Direct Vehicle Fit: Universal — suitable for any vehicle metal panel surface Goes Well With: Stinger RKU8 Roadkill Ultimate (premium 3-layer upgrade — apply Ultimate on critical areas, Expert on larger surfaces) Stinger RKCP12 Roadkill Carpet Foam Pad (apply Expert to floor metal, then RKCP12 under carpet) Stinger RKFR6 / RKFR69 Roadkill Fast Rings (for speaker mounting point acoustic coupling) Stinger RKINSTALL sound deadener installation kit (roller and knife for application) Frequently Asked Questions How does Roadkill Expert differ from Roadkill Ultimate? Roadkill Expert is a two-layer product — butyl damping layer plus aluminium top. Roadkill Ultimate is a three-layer product that adds an acoustic foam layer on top of the aluminium, combining vibration damping, heat dissipation, and high-frequency sound absorption in one sheet. Expert is the cost-effective bulk option; Ultimate is the premium single-application solution where maximum performance per sheet is needed. How do I apply Roadkill Expert? Clean the metal surface with wax and grease remover or methylated spirits and allow it to dry fully. Cut the sheet to shape, peel the backing, press it firmly onto the panel, and roll with the Stinger RKINSTALL roller to ensure full contact and maximum adhesion. Is 36 sq ft enough for a full interior treatment? 36 sq ft is sufficient for both front door inner skins and a boot floor, or the floor area of a small to medium vehicle. For a comprehensive full-interior treatment including doors, floor, and roof, additional packs are recommended. Contact the F.A.E. team for guidance based on your specific vehicle. Can Roadkill Expert be applied to a vehicle firewall? Yes. The firewall is one of the most effective application points for Roadkill Expert — it reduces heat transfer from the engine bay and exhaust, as well as engine vibration transmitted into the cabin. Is Roadkill Expert safe to install in an enclosed vehicle cabin? Yes. Roadkill Expert is odourless and non-toxic, with no off-gassing or unpleasant smells after installation — safe for the vehicle cabin immediately after application. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger RKINSTALL Roadkill Sound Deadener Installation Kit The right tools for a professional sound deadener installation extra-wide urethane application roller and a heavy-duty utility knife with interchangeable blades. Designed for use with Stinger Roadkill and similar adhesive sound deadening materials. Product Overview The Stinger RKINSTALL is a two-piece installation kit designed for applying adhesive vibration-damping and sound deadening materials such as Stinger Roadkill. It includes an extra-wide urethane application roller for pressing the material firmly and evenly onto surfaces, and a utility knife for cleanly trimming sheets with aluminium backing. The wooden-handled roller is built for repeated use and delivers a smooth, professional finish with minimal effort. The utility knife accepts standard Stanley-style blades available at any hardware store, making blade replacement simple and cost-effective. Features & Benefits Extra-wide urethane application roller for smooth, professional adhesion Wooden roller handle — built for repeated installer use Utility knife with interchangeable standard Stanley-style blades Belt clip keeps tools accessible during installation Designed for Stinger Roadkill and compatible adhesive sound deadening materials Technical Specs Specification Detail SKU / Part Number RKINSTALL Brand Stinger Kit Contents Urethane application roller (extra-wide) and utility knife Roller Material Wood handle with urethane application wheel Knife Blade Type Standard Stanley-style interchangeable blades Belt Clip Included Yes Compatible With / Goes Well With Direct Vehicle Fit: Universal — suitable for sound deadener installation in any vehicle Goes Well With: Stinger Roadkill sound deadening and vibration damping materials Dynamat and other adhesive-backed sound deadening sheets Any self-adhesive vibration damping or butyl-based sound deadening product Frequently Asked Questions What types of sound deadening material is this kit designed for? The RKINSTALL is designed for adhesive-backed sound deadening sheets such as Stinger Roadkill and similar products. The roller presses the material firmly onto panels and floors, and the knife trims sheets with aluminium or foil backing cleanly and accurately. What blades does the utility knife use? The knife accepts standard Stanley-style interchangeable blades, which are widely available at any hardware store. Replacement blades are not included but are inexpensive and easy to source. Can the roller be used for other adhesive installations? Yes. The urethane roller is suitable for any adhesive sheet product that requires firm, even pressing — including vinyl wrapping, heat shield materials, and other automotive adhesive products. Is this kit suitable for professional installer use? Yes. Both tools are built for repeated installer use — the wooden roller handle is durable and designed to last across multiple installations, and the all-metal knife construction withstands regular use. Are replacement blades included? No. Replacement blades for the utility knife are not included. Standard Stanley-style blades are available at any hardware store. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger RKCP12 Roadkill Carpet Foam Pad for Floors & Transmission Humps (12 Sq Ft) Dual-layer foam and butyl-vinyl carpet pad for vehicle floors and transmission humps reduces road noise, insulates the cabin, and pairs perfectly with Stinger Roadkill Expert for maximum sound damping results. Product Overview The Stinger RKCP12 is a dual-layer carpet foam damping pad designed to be placed between the factory floor and the existing carpet or vinyl covering in your vehicle. It combines a high-density semi-closed cell foam layer for cushioning and insulation with a high-mass butyl-vinyl decoupling layer for effective road noise reduction across a broad frequency range. Installed under the floor carpet, the RKCP12 significantly reduces low-frequency road and transmission hump noise, reduces driving fatigue, and improves cabin temperature regulation helping keep the interior cooler in summer and warmer in winter without extra load on the HVAC system. Odourless and non-toxic no unpleasant smells after installation. Easy to install: roll out, mark to shape with a texta, and cut with scissors or a knife to fit the floor profile. Features & Benefits Dual-layer construction: high-density semi-closed cell foam + high-mass butyl-vinyl decoupling layer Installs under factory carpet or vinyl — no permanent modification required Broad frequency road noise and vibration damping Reduces low-frequency road and transmission hump noise Insulates cabin — more efficient HVAC in summer and winter Odourless and non-toxic Easy to cut and shape with standard scissors or a knife Pairs with Stinger Roadkill Expert for maximum damping results Technical Specs Specification Detail SKU / Part Number RKCP12 Brand Stinger Series Roadkill Coverage 12 sq ft (approx. 81cm × 137cm / 32" × 54") Minimum Thickness 7.8mm Damping Weight 0.41 lbs/ft² Peel Adhesion Strength 38.24 lbs/in after 24 hours Application Temperature –51°C to 149°C (–60°F to 300°F) Construction Dual layer — foam + butyl-vinyl Odour Odourless Compatible With / Goes Well With Direct Vehicle Fit: Universal — suitable for any vehicle floor and transmission hump Goes Well With: Stinger Roadkill Expert sound damping sheets (apply first, then lay RKCP12 over the top) Stinger RKINSTALL sound deadener installation kit (roller and knife for easy installation) Frequently Asked Questions How does this differ from standard Roadkill sound damping sheets? Stinger Roadkill Expert sheets are self-adhesive vibration-damping panels applied directly to the vehicle's metal floor, reducing panel resonance. The RKCP12 carpet pad is not adhesive — it sits between the metal floor (or over the applied Roadkill Expert) and the factory carpet, adding foam cushioning and an additional decoupling layer for road noise reduction. For best results, use both together. Does this require adhesive to install? No. The RKCP12 is not adhesive — it is simply cut to shape and laid under the factory carpet, which holds it in position. No glue or bonding is required. Does this work for thermal insulation as well as sound? Yes. The high-density foam layer acts as thermal insulation, reducing heat transfer through the floor. This helps keep the cabin cooler in summer and warmer in winter, reducing HVAC load. Is 12 square feet enough to cover a full vehicle floor? 12 square feet (approx. 81cm × 137cm) covers the front footwells or a portion of the transmission hump in most vehicles. For full-floor coverage, multiple rolls or a larger product may be required. Contact the F.A.E. team to confirm how many rolls are needed for your specific vehicle. Is this product safe to install in an enclosed vehicle cabin? Yes. The RKCP12 is odourless and non-toxic — safe for use inside the vehicle cabin with no off-gassing or unpleasant smells after installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MTIBR73 InstallBay HDMI & USB Flush Mount Extension Kit, 6ft A 6-foot HDMI and USB extension cable with two mounting options flush-mount into a 3/4-inch drilled hole for an OEM finish, or use the included bracket for a no-drill installation. Product Overview The Stinger MTIBR73 is a combined HDMI and USB extension cable designed to remote-mount the HDMI and USB inputs of an aftermarket head unit to a convenient location in the vehicle. The cable provides a 6-foot (approximately 1.8m) extension from the head unit's rear HDMI and USB ports, with a female flush-mount end that can be installed in two ways: Drilled flush mount: Drill a 3/4-inch hole at the desired location (dash, centre console, glovebox, trim panel) and snap the connector in for a clean, OEM-style finish. Bracket mount: Snap the cable into the included mounting bracket and fix it wherever the installation demands no drilling required. Ideal for newer aftermarket head units that feature rear USB and HDMI inputs, allowing a clean front-accessible connection point for CarPlay/Android Auto and high-definition video sources. Features & Benefits Extends both HDMI and USB inputs from an aftermarket head unit to a remote flush-mount location Two mounting options — drilled flush mount (3/4-inch hole) or bracket mount (no drilling) 6-foot (approximately 1.8m) cable length Female flush-mount end for clean, OEM-style installation Mounting bracket included Black finish Ideal for head units with rear HDMI and USB inputs Technical Specs Specification Detail SKU / Part Number MTIBR73 Brand Stinger Series InstallBay Cable Length 6ft (approx. 1.8m) Colour Black Connections HDMI + USB Flush Mount Hole Size 3/4-inch (19mm) Mounting Options Drilled flush mount or bracket mount Includes HDMI/USB extension cable, mounting bracket Compatible With / Goes Well With Direct Vehicle Fit: Universal — compatible with any aftermarket head unit featuring rear HDMI and USB inputs Goes Well With: Stinger HEIGH10 UN1810 (dual rear USB + rear HDMI input) Stinger SRP-JW07H and SRP-RAM13H HEIGH10 infotainment kits (dual rear USB + HDMI) Aftermarket head units with rear HDMI and USB inputs (Pioneer, Kenwood, Sony, JVC) Stinger IPUSBD6 dual USB flush mount extension kit (USB-only alternative) Frequently Asked Questions Can I install this without drilling into my dash? Yes. The included mounting bracket allows the HDMI/USB connector to be mounted securely without any drilling — simply snap the cable end into the bracket and fix it to a suitable surface. What size hole is needed for the flush mount option? A 3/4-inch (approximately 19mm) hole is required for the drilled flush mount option. Once snapped in, the connector sits flush with the panel surface for a clean, OEM-style appearance. Does this cable extend both HDMI and USB simultaneously? Yes. The MTIBR73 extends both the HDMI input and the USB input in a single cable assembly, providing both connections at the remote mount location. What is the cable length? The MTIBR73 is 6 feet (approximately 1.8m) long. For most vehicle installations — dash to glovebox, console, or trim panel — this provides adequate reach. Confirm the required routing distance before purchasing. Is this compatible with the Stinger HEIGH10? Yes. The HEIGH10 (UN1810) features dual rear USB inputs and a rear HDMI input — the MTIBR73 can be used to remote-mount both connection types from the HEIGH10 to a convenient front-accessible location. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MTCHTO-013 Radio Replacement & Factory Amplifier Retention Interface for Chrysler, Dodge & Jeep (2005–2011) Retains the factory OEM amplifier in select Chrysler, Dodge, and Jeep vehicles when replacing the factory head unit with RAP, balance/fade, blind spot detection, navigation outputs, and SWC pre-wiring all included. Product Overview The Stinger MTCHTO-013 is a radio replacement interface designed for retention of the factory OEM amplifier in Chrysler PT Cruiser, Dodge Caliber, and select Jeep models (2005–2011). Compatible with both non-amplified and amplified factory audio systems, it bridges the new aftermarket head unit to the vehicle's electrical and audio systems, retaining a wide range of factory features. Key retentions include the factory amplifier (with balance and fade preserved), Retained Accessory Power (RAP), audible blind spot detection, and high-level speaker input for amplified systems. Navigation signal outputs (parking brake, reverse, mute, speed sense) are also provided. A pre-wired ASWC-1 harness is included for steering wheel control retention the MTASWC-1 SWC interface is sold separately. The interface is Micro B USB updatable for future firmware revisions. Features & Benefits Retains factory OEM amplifier — compatible with non-amplified and amplified systems Retains balance and fade control Retains Retained Accessory Power (RAP) Retains audible blind spot detection system High-level speaker input for amplified audio systems Provides accessory power (12V, 10A) Provides navigation outputs — parking brake, reverse, mute, and speed sense Pre-wired ASWC-1 harness for SWC retention — MTASWC-1 sold separately Micro B USB updatable firmware Suitable for both non-amplified and amplified factory audio configurations Technical Specs Specification Detail SKU / Part Number MTCHTO-013 Brand Stinger Function Radio replacement and factory amplifier retention interface Amplifier Compatibility Non-amplified and amplified systems Accessory Power Output 12V, 10A RAP Retention Yes Balance & Fade Retention Yes Blind Spot Detection Retention Yes (audible) Navigation Outputs Parking Brake, Reverse, Mute, Speed Sense SWC Pre-Wiring Yes — ASWC-1 harness pre-wired (MTASWC-1 sold separately) Firmware Updatable Yes — Micro B USB Compatible With / Goes Well With Direct Vehicle Fit: Chrysler PT Cruiser 2006–2011 (2nd Gen) Dodge Caliber 2006–2009 (1st Gen) Jeep Commander 2005–2008 (XK) Jeep Compass 2007–2009 (MK) Jeep Grand Cherokee 2005–2009 (WH) Jeep Patriot 2007–2009 (MK) Goes Well With: MTASWC-1 SWC interface (sold separately — required for steering wheel control retention) Aftermarket head units with standard ISO connections Stinger ST27AA06 / ST27AA14 antenna adaptors (for applicable Jeep/Chrysler/Dodge models) Frequently Asked Questions Do I need the MTASWC-1 to retain steering wheel controls? Yes. The MTCHTO-013 includes a pre-wired ASWC-1 harness for convenience, but the MTASWC-1 SWC interface module itself is sold separately and is required to retain factory steering wheel audio controls. Purchase the MTASWC-1 alongside this interface if SWC retention is needed. Does this interface work with both amplified and non-amplified factory audio systems? Yes. The MTCHTO-013 is a dual-mode interface compatible with both non-amplified and amplified factory audio configurations in the listed Chrysler, Dodge, and Jeep models. What is Retained Accessory Power (RAP)? RAP is a factory feature that keeps certain vehicle accessories (such as the radio, windows, and sunroof) powered for a short period after the ignition is switched off. The MTCHTO-013 retains this function so it continues to operate correctly with the aftermarket head unit. Does this interface retain the blind spot detection warning tones? Yes. The audible blind spot detection system is retained by the MTCHTO-013, so the warning chimes continue to function after the factory head unit is replaced. Is this interface firmware updatable? Yes. The MTCHTO-013 supports firmware updates via a Micro B USB connection, allowing future improvements or compatibility updates to be applied without replacing the unit. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MTAXMBUSB Factory USB Socket Retention Adaptor for Mercedes Vehicles (2004–2018) Retain the factory USB socket in your Mercedes when replacing the factory radio plug-and-play adaptor covering 15 Mercedes models from 2004 to 2018. Product Overview The Stinger MTAXMBUSB is a vehicle-specific USB retention adaptor for select Mercedes vehicles, allowing the factory USB socket to remain functional after the factory radio has been replaced with an aftermarket head unit. It connects the factory USB socket wiring to the rear USB input on the aftermarket head unit. Features & Benefits Retains factory USB socket when replacing the factory radio Connects factory USB wiring to aftermarket head unit's rear USB input Plug and play — no cutting or splicing required Covers 15 Mercedes models from 2004–2018 Technical Specs Specification Detail SKU / Part Number MTAXMBUSB Brand Stinger Function Factory USB socket retention Sockets Retained USB Prerequisite Aftermarket head unit must have rear USB input Vehicle Application Mercedes (see compatibility list) Compatible With / Goes Well With Direct Vehicle Fit: Mercedes A Class 2007–2011 (W169) Mercedes A Class 2013–2016 (W176) Mercedes B Class 2005–2007 (W245) Mercedes B Class 2007–2011 (W245) Mercedes C Class 2005–2008 (W203) Mercedes C Class 2008–2011 (W204) Mercedes C Class 2011–2014 (W204) Mercedes CLK 2005–2011 (W209) Mercedes E Class 2008–2011 (W212) Mercedes M Class 2005–2011 (W164) Mercedes R Class 2006–2012 (W251) Mercedes SL Class 2005–2013 (R230) Mercedes SLK Class 2004–2011 (R171) Mercedes Sprinter 2007–2018 (W906) Mercedes Vito (incl. Viano & Valente) 2007–2015 (W639) Goes Well With: Aftermarket head units with rear USB input (Pioneer, Kenwood, Sony, JVC, Stinger) Vehicle-specific ISO wiring harnesses for Mercedes Stinger ST27AA06 / ST27AA14 antenna adaptors (for applicable Mercedes models) Stinger PC7-AUX-MB01 AUX/USB retention adaptor (for Mercedes Vito W447 — newer generation) Frequently Asked Questions Does my aftermarket head unit need a rear USB input for this adaptor to work? Yes. The MTAXMBUSB connects the factory USB socket wiring to the rear USB input on the aftermarket head unit. If your chosen head unit does not have a rear USB input, the factory socket cannot be retained. Confirm your head unit's rear USB input availability before purchasing. Despite the title saying "BMW/Mercedes," does this fit BMW vehicles? The compatibility list for the MTAXMBUSB covers Mercedes models only — no BMW vehicles are listed. If you need a USB retention adaptor for a BMW, contact the F.A.E. team to confirm the correct product. Is any cutting or splicing required? No. The MTAXMBUSB is a plug-and-play adaptor that connects to the factory USB wiring without cutting or modifying the factory harness. I have a Mercedes Vito — should I use the MTAXMBUSB or the PC7-AUX-MB01? It depends on your Vito's generation. The MTAXMBUSB covers the Mercedes Vito W639 (2007–2015). The PC7-AUX-MB01 covers the newer W447 (2015–2019) and also retains the AUX socket in addition to USB. Confirm your Vito's chassis code before purchasing. Does this adaptor fit all Mercedes models? No. The MTAXMBUSB covers the specific Mercedes models and year ranges listed above. For other Mercedes models not listed, contact the F.A.E. team to confirm the correct USB retention solution. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MT99-6526S Single/Double DIN Radio Fascia Kit for Jeep Cherokee (2014 Onwards) A vehicle-specific fascia kit for the Jeep Cherokee (2014 onwards) supporting both single DIN and double DIN aftermarket head unit installation silver finish with mounting brackets included. Product Overview The Stinger MT99-6526S is a radio fascia kit designed for the Jeep Cherokee (2014 onwards). It supports both 1DIN and 2DIN aftermarket head unit installations and includes mounting brackets for a secure fit. The silver finish suits the Cherokee's interior trim. Please note: Specific chassis code and year range end point are not confirmed in the available supplier data. Contact the F.A.E. team to confirm exact fitment for your Jeep Cherokee model year and variant before purchasing. Features & Benefits Supports single DIN (1DIN) and double DIN (2DIN) aftermarket radio installation Mounting brackets included Silver finish Suits Jeep Cherokee 2014 onwards Technical Specs Specification Detail SKU / Part Number MT99-6526S Brand Stinger Colour / Finish Silver Radio Size Compatibility Single DIN (1DIN) and Double DIN (2DIN) Mounting Brackets Included Yes Vehicle Compatibility Jeep Cherokee 2014 onwards — chassis code and year end not confirmed Antenna Adaptor Included Not included Wiring Harness Included Not included SWC Interface Included Not included Compatible With / Goes Well With Direct Vehicle Fit: Jeep Cherokee 2014 onwards — confirm specific year range and chassis code with F.A.E. before purchasing Goes Well With: Aftermarket single DIN or double DIN head units (Pioneer, Kenwood, Sony, JVC, Stinger) Vehicle-specific ISO wiring harness for Jeep Cherokee Antenna adaptor for Jeep/Chrysler (if required by chosen head unit) Steering wheel control interface for Jeep Cherokee (if applicable) Frequently Asked Questions Which Jeep Cherokee variants does this kit fit? The MT99-6526S is specified for the Jeep Cherokee from 2014 onwards, but the exact chassis code and year range end point are not confirmed in the available supplier data. Contact the F.A.E. team to confirm fitment for your specific Cherokee variant before purchasing. Does this kit support both single DIN and double DIN head units? Yes. The MT99-6526S accommodates both 1DIN and 2DIN aftermarket head units. Is a wiring harness included? No. The MT99-6526S is a fascia and bracket kit only. A vehicle-specific ISO wiring harness will need to be sourced separately to connect your aftermarket head unit to the factory wiring. Are mounting brackets included? Yes. The MT99-6526S includes mounting brackets for securing the aftermarket head unit in the factory dash opening. Is an antenna adaptor included? No. An antenna adaptor is not included. A Jeep/Chrysler-specific antenna adaptor may be required — confirm with the F.A.E. team before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MT99-6526BZ Single/Double DIN Radio Fascia Kit for Jeep Cherokee (2014 Onwards) A vehicle-specific fascia kit for the Jeep Cherokee (2014 onwards) supporting both single DIN and double DIN aftermarket head unit installation silver finish with mounting brackets included. Product Overview The Stinger MT99-6526BZ is a radio fascia kit for the Jeep Cherokee (2014 onwards), supporting both 1DIN and 2DIN aftermarket head unit installations. Mounting brackets are included and the silver finish suits the Cherokee's interior trim. Please note: Specific chassis code and year range end point are not confirmed in the available supplier data. Contact the F.A.E. team to confirm exact fitment for your Jeep Cherokee model year and variant before purchasing. The MT99-6526BZ and MT99-6526S appear to cover the same vehicle with the same specifications. Contact the F.A.E. team to confirm which SKU is correct for your installation before ordering. Features & Benefits Supports single DIN (1DIN) and double DIN (2DIN) aftermarket radio installation Mounting brackets included Silver finish Suits Jeep Cherokee 2014 onwards Technical Specs Specification Detail SKU / Part Number MT99-6526BZ Brand Stinger Colour / Finish Silver Radio Size Compatibility Single DIN (1DIN) and Double DIN (2DIN) Mounting Brackets Included Yes Vehicle Compatibility Jeep Cherokee 2014 onwards — chassis code and year end not confirmed Antenna Adaptor Included Not included Wiring Harness Included Not included SWC Interface Included Not included Compatible With / Goes Well With Direct Vehicle Fit: Jeep Cherokee 2014 onwards — confirm specific year range and chassis code with F.A.E. before purchasing Goes Well With: Aftermarket single DIN or double DIN head units (Pioneer, Kenwood, Sony, JVC, Stinger) Vehicle-specific ISO wiring harness for Jeep Cherokee Antenna adaptor for Jeep/Chrysler (if required by chosen head unit) Steering wheel control interface for Jeep Cherokee (if applicable) Frequently Asked Questions What is the difference between the MT99-6526BZ and the MT99-6526S? Both SKUs appear to cover the same Jeep Cherokee application with the same specifications. Contact the F.A.E. team to confirm which is correct for your installation before ordering. Which Jeep Cherokee variants does this kit fit? The MT99-6526BZ is specified for the Jeep Cherokee from 2014 onwards, but the exact chassis code and year range end point are not confirmed in the available supplier data. Contact the F.A.E. team to confirm fitment for your specific Cherokee variant before purchasing. Does this kit support both single DIN and double DIN head units? Yes. The MT99-6526BZ accommodates both 1DIN and 2DIN aftermarket head units. Is a wiring harness included? No. The MT99-6526BZ is a fascia and bracket kit only. A vehicle-specific ISO wiring harness will need to be sourced separately to connect your aftermarket head unit to the factory wiring. Is an antenna adaptor included? No. An antenna adaptor is not included. A Jeep/Chrysler-specific antenna adaptor may be required — confirm with the F.A.E. team before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MT99-6520B Single/Double DIN Radio Fascia Kit for Dodge Journey & Fiat Freemont (2012–2015) A fascia kit for the Dodge Journey and Fiat Freemont (2012–2015) supporting both single DIN and double DIN aftermarket head unit installation black finish with mounting brackets included. Product Overview The Stinger MT99-6520B is a radio fascia kit for the Dodge Journey (2012–2015) and Fiat Freemont (2012–2015), which share the same platform and factory dash configuration. It supports both 1DIN and 2DIN aftermarket head unit installations and includes mounting brackets. The black finish matches the factory interior trim. Please note: Vehicle compatibility is listed as "known to work" by the supplier rather than confirmed fitment. Contact the F.A.E. team to confirm fitment for your specific variant before purchasing. Features & Benefits Supports single DIN (1DIN) and double DIN (2DIN) aftermarket radio installation Covers Dodge Journey and Fiat Freemont 2012–2015 Mounting brackets included Black finish matched to factory interior trim Technical Specs Specification Detail SKU / Part Number MT99-6520B Brand Stinger Colour / Finish Black Radio Size Compatibility Single DIN (1DIN) and Double DIN (2DIN) Mounting Brackets Included Yes Antenna Adaptor Included Not included Wiring Harness Included Not included SWC Interface Included Not included Compatible With / Goes Well With Direct Vehicle Fit (known to work): Dodge Journey 2012–2015 Fiat Freemont 2012–2015 Goes Well With: Aftermarket single DIN or double DIN head units (Pioneer, Kenwood, Sony, JVC, Stinger) Vehicle-specific ISO wiring harness for Dodge/Fiat Antenna adaptor for Chrysler/Dodge (if required by chosen head unit) Steering wheel control interface for Dodge Journey / Fiat Freemont (if applicable) Frequently Asked Questions Why does this fascia kit cover both Dodge and Fiat vehicles? The Dodge Journey and Fiat Freemont are the same vehicle sold under different brand names in different markets — they share the same platform, body, and factory dash configuration. A single fascia kit fits both. Does this kit support both single DIN and double DIN head units? Yes. The MT99-6520B accommodates both 1DIN and 2DIN aftermarket head units. Is a wiring harness included? No. The MT99-6520B is a fascia and bracket kit only. A vehicle-specific ISO wiring harness will need to be sourced separately to connect your aftermarket head unit to the factory wiring. Are mounting brackets included? Yes. The MT99-6520B includes mounting brackets for securing the aftermarket head unit in the factory dash opening. Is an antenna adaptor included? No. An antenna adaptor is not included. A Chrysler/Dodge-specific antenna adaptor may be required — confirm the correct type with the F.A.E. team before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger MT99-5839CH Single/Double DIN Radio Fascia Kit for Ford Mustang 5th Gen (2010–2014) A vehicle-specific fascia kit for the Ford Mustang 5th Generation (2010–2014) supporting both single DIN and double DIN aftermarket head unit installation charcoal finish with mounting brackets included. Product Overview The Stinger MT99-5839CH is a radio fascia kit designed for the Ford Mustang 5th Generation (2010–2014). It supports both 1DIN and 2DIN aftermarket head unit installations and includes mounting brackets for a secure fit. The charcoal finish complements the Mustang's interior trim. Features & Benefits Supports single DIN (1DIN) and double DIN (2DIN) aftermarket radio installation Vehicle-specific fit for Ford Mustang 5th Gen 2010–2014 Mounting brackets included Charcoal finish matched to factory interior trim Technical Specs Specification Detail SKU / Part Number MT99-5839CH Brand Stinger Colour / Finish Charcoal Radio Size Compatibility Single DIN (1DIN) and Double DIN (2DIN) Mounting Brackets Included Yes Antenna Adaptor Included Not included Wiring Harness Included Not included SWC Interface Included Not included Compatible With / Goes Well With Direct Vehicle Fit: Ford Mustang 2010–2014 (5th Generation) Goes Well With: Aftermarket single DIN or double DIN head units (Pioneer, Kenwood, Sony, JVC, Stinger) Vehicle-specific ISO wiring harness for Ford Mustang Stinger ST27AA06 / ST27AA21 antenna adaptors (for Ford Mustang 5th Gen) Steering wheel control interface for Ford Mustang (if applicable) Frequently Asked Questions Does this kit fit all Ford Mustang 5th Gen variants from 2010–2014? The MT99-5839CH is specified for the Ford Mustang 5th Generation (2010–2014). For confirmation of fitment across specific trim levels or variants such as the GT, GT500, or Boss 302, contact the F.A.E. team before purchasing. Does this kit support both single DIN and double DIN head units? Yes. The MT99-5839CH accommodates both 1DIN and 2DIN aftermarket head units. Is a wiring harness included? No. The MT99-5839CH is a fascia and bracket kit only. A vehicle-specific ISO wiring harness will need to be sourced separately to connect your aftermarket head unit to the factory wiring. Are mounting brackets included? Yes. The MT99-5839CH includes mounting brackets for securing the aftermarket head unit in the factory dash opening. Is an antenna adaptor included? No. An antenna adaptor is not included. A Ford-specific antenna adaptor may be required — confirm the correct type with the F.A.E. team before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less