100 Amp ANL Fuse Platinum Finish. 2-Pack. The Rockford Fosgate RFFA100 is a 100A platinum-plated ANL fuse supplied as a 2-pack. Suitable for car audio power runs requiring 100A overcurrent protection the entry-level rating in the Rockford Fosgate ANL fuse range, appropriate for single mid-power amplifier installations. Compatible with the Rockford Fosgate RFFANL inline fuse holder and standard ANL fuse holders. Key Specifications Specification Detail Part Number RFFA100 Fuse Type ANL Amperage 100A ✓ Finish Platinum ✓ Pack Quantity 2 ✓ Voltage Rating Not specified Dimensions ANL standard Warranty Not specified Features & Benefits 100A Rating — The lowest rating in the Rockford Fosgate ANL fuse range — suitable for single amplifier power runs drawing up to approximately 100A continuously. Typically appropriate for amplifiers rated up to approximately 750–1,000W depending on supply voltage and efficiency. Platinum Plated — Low contact resistance and corrosion protection at the fuse holder interface. ANL Format — Compatible with RFFANL and standard ANL fuse holders. 2-Pack — Installation fuse plus spare. FAQs When is a 100A fuse the right choice? A 100A ANL fuse is appropriate for installations where total continuous system current draw approaches 100A. This suits a single high-powered amplifier or a modest two-amplifier system. For higher total current draws, consider the RFFA150, RFFA200, RFFA300, or RFFA500. Is a spare included? Yes — 2-pack. Compatible holder? Rockford Fosgate RFFANL and standard ANL fuse holders. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

1/0 AWG Distribution Block 1 Input, 2 Outputs, Accepts 1/0 AWG or 4 AWG. Custom Tooled Solid Brass with HPP Platinum Finish. Product Overview The Rockford Fosgate RFD1 is a 1/0 AWG distribution block with one input and two outputs splitting one main power or ground cable into two separate runs. Both the input and each output accept 1/0 AWG or 4 AWG wire, providing wiring flexibility for systems where the main run is 1/0 AWG and secondary runs are either 1/0 AWG or the smaller 4 AWG gauge. Constructed from custom-tooled solid brass with HPP (High Performance Plating) platinum finish for superior corrosion resistance. Key Specifications Part number: RFD1 Configuration: 1 input / 2 outputs Input wire size: 1/0 AWG or 4 AWG ✓ Output wire sizes: 1/0 AWG or 4 AWG per output ✓ Construction: Custom tooled solid brass ✓ Plating: HPP (High Performance Plating) — platinum finish ✓ Corrosion resistance: Superior (HPP confirmed) ✓ Terminal type: Not specified — confirm with Rockford Fosgate (set screw or bolt) Mounting: Not specified — confirm with Rockford Fosgate Maximum current rating: Not specified — confirm with Rockford Fosgate Dimensions: Not specified — confirm with Rockford Fosgate Weight: Not specified Features & Benefits 1 In / 2 Out Configuration — Splits one main power or ground cable into two independent output runs — suitable for powering two amplifiers from a single main cable, or routing power to an amplifier and a secondary distribution point. 1/0 AWG or 4 AWG Input and Output Flexibility — Both the input and each output accept either 1/0 AWG or 4 AWG wire, allowing the block to be used across different system configurations: 1/0 AWG main to two 1/0 AWG outputs, 1/0 AWG main to two 4 AWG outputs, or mixed configurations. Custom Tooled Solid Brass — The block body is machined from solid brass rather than cast or stamped — providing precise dimensional tolerances, high current capacity, and better thermal performance than lower-grade materials. Solid brass construction also provides the mechanical strength to hold high-torque terminal screws securely. HPP Platinum Plating — Superior Corrosion Resistance — HPP plating protects the brass body against oxidation and corrosion in vehicle environments, maintaining low contact resistance at the conductor interface over time. Technical Specs Specification Detail Brand Rockford Fosgate Part Number RFD1 Configuration 1 Input / 2 Outputs Input Wire Size 1/0 AWG or 4 AWG ✓ Output Wire Sizes 1/0 AWG or 4 AWG (per output) ✓ Construction Custom Tooled Solid Brass ✓ Plating HPP Platinum ✓ Terminal Type Not specified — confirm with Rockford Fosgate Current Rating Not specified — confirm with Rockford Fosgate Mounting Not specified Dimensions Not specified Weight Not specified Warranty Not specified Compatible With / Goes Well With Suitable for: Splitting a 1/0 AWG main power run to two amplifiers Power distribution in multi-amplifier systems using 1/0 AWG or 4 AWG secondary runs Ground distribution from a single chassis ground point Pairs well with: Rockford Fosgate RFW1R-51 / RFW1B-51 (1/0 AWG wire for main run) Rockford Fosgate RFT4 / RFTS4 (4 AWG terminals for output runs) Rockford Fosgate amplifiers requiring distributed power supply Frequently Asked Questions What is a distribution block and why is it used? A distribution block connects one main power or ground cable to multiple output cables — allowing a single 1/0 AWG battery-to-boot run to supply two or more amplifiers independently. Without a distribution block, each amplifier would require its own full-length power run from the battery. Can the RFD1 mix 1/0 AWG and 4 AWG wires? Yes — both input and output ports accept either 1/0 AWG or 4 AWG, providing flexibility to mix gauges. For example, a 1/0 AWG main input can be distributed to two 4 AWG outputs for a pair of smaller amplifiers, or to one 1/0 AWG and one 4 AWG output. What is the maximum current capacity? Maximum current rating is not confirmed in the supplier data. Given solid brass construction and 1/0 AWG input capacity, the block is designed for high-current applications. Confirm the rated current from the official Rockford Fosgate RFD1 product page. How is the RFD1 mounted? Mounting method is not specified in the supplier data. Confirm from the official Rockford Fosgate RFD1 product page — typical distribution block mounting uses screws through the block body or a bracket. What terminal type (set screw or bolt) does the RFD1 use? Terminal type is not specified. Confirm from the official Rockford Fosgate RFD1 product page before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate RFCB200 200 Amp Circuit Breaker When a blown fuse at the wrong moment means a full rewire job, the RFCB200 replaces a standard fuse holder with a 200-amp manual-reset circuit breaker that gets your system back online without touching the wiring. Product Overview The RFCB200 is Rockford Fosgate's 200 Amp Circuit Breaker, designed to protect high-power car audio amplifier systems from overcurrent events without the cost and downtime of replacing a blown fuse. Rated at 200 amps, it covers the protection requirements of high-output monoblock and multi-amplifier installations running 1/0 AWG or 4 AWG main power cable. All terminals are platinum plated for superior corrosion resistance and low-resistance electrical contact, and use a set-screw style connection that accepts bare wire directly without requiring ring terminals, simplifying installation and future servicing. When an overcurrent event occurs, the RFCB200 trips rather than blowing, and can be manually reset once the fault has been identified and cleared. The low-resistance, high-current design ensures minimal voltage drop across the breaker during normal operation, preserving maximum available voltage at the amplifiers. 1-year warranty. Features & Benefits Manual Reset Circuit Breaker: Unlike a fuse that must be replaced after an overcurrent event, the RFCB200 trips and can be manually reset once the fault condition has been resolved. This eliminates the need to carry spare fuses and allows the system to be restored to operation quickly in the field. 200 Amp Rating: Rated at 200 amps continuous, the RFCB200 provides the overcurrent protection threshold required by high-power amplifier systems, including monoblock subwoofer amplifiers such as the R2-1200X1 and multi-amplifier builds where combined fuse requirements reach or exceed this rating. Platinum Plated Terminals: All connection terminals are platinum plated for superior corrosion resistance and low-resistance electrical contact, maintaining a clean, reliable connection over the life of the installation without the oxidation issues common to standard plated terminals. Set-Screw Style Connection: The set-screw terminal design accepts bare wire directly without requiring ring terminals or crimped lugs, reducing the number of connection points in the power run and simplifying both initial installation and future servicing. Multiple Wire Gauge Compatibility: Accepts 1/0 AWG and 4 AWG power cable, covering the wiring gauge requirements of the majority of high-power car audio amplifier installations without requiring adaptor fittings. Low-Resistance, High-Current Design: Internal resistance is minimised to ensure negligible voltage drop across the breaker during normal operation, preserving the full supply voltage available from the battery and alternator for the amplifiers downstream. Technical Specs Specification Detail SKU RFCB200 Current Rating 200A Reset Type Manual Reset Terminal Plating Platinum Terminal Type Set-Screw (no ring terminals required) Wire Gauge Compatibility 1/0 AWG, 4 AWG Warranty 1 Year Goes Well With The RFCB200 is a direct replacement for the main power fuse or fuse holder in high-power car audio installations. It is best suited to systems running high-output monoblock amplifiers such as the R2-1200X1, which specifies a 200A recommended fuse, or multi-amplifier builds where combined fuse requirements approach this rating. It sits in the main power cable run between the battery and the amplifier distribution point, installed as close to the battery as possible. A 1/0 AWG amplifier wiring kit is recommended for power and ground runs at this current rating. For systems also using the RFC10HB capacitor, the RFCB200 is installed in the power cable between the battery and the capacitor. Frequently Asked Questions What is the advantage of a circuit breaker over a standard blade or ANL fuse in a car audio system? A standard fuse is a one-time protection device that must be physically replaced after an overcurrent event, which can mean carrying spare fuses and a delay in restoring the system if a fault occurs away from home. A manual-reset circuit breaker like the RFCB200 trips when an overcurrent event occurs and can be reset by hand once the fault has been identified and cleared, restoring the system to operation without replacing any components. Does the RFCB200 require ring terminals for installation? No. The set-screw terminal design on the RFCB200 accepts bare wire directly, tightened into the terminal with the set screw. This removes the need for ring terminals or crimped lugs at the breaker connection points, reducing the number of potential resistance points in the power run and making installation and future servicing more straightforward. Where should the RFCB200 be installed in the power cable run? The RFCB200 should be installed in the positive power cable as close to the battery terminal as possible, within 30-45 cm of the battery in most installations. This placement ensures that the maximum length of power cable between the battery and the amplifiers is protected against overcurrent and short-circuit events. The negative or ground cable does not pass through the circuit breaker. What amplifiers does the 200 amp rating suit? The 200 amp rating covers the protection requirement for Rockford Fosgate's R2-1200X1 monoblock amplifier, which specifies a 200A recommended fuse, making the RFCB200 a direct match for that amplifier's power protection needs. It also covers multi-amplifier builds where the combined fuse ratings of several amplifiers add up to this threshold. For lower-power systems specifying 60A or 50A fuses, the RFCB100 or RFCB140 are the appropriate options. Can the RFCB200 be used as a main disconnect switch as well as a circuit breaker? The RFCB200 is a circuit breaker with manual reset capability, not a purpose-designed disconnect switch. While manually tripping the breaker will interrupt the power supply to the amplifiers, it is not rated or designed as a deliberate on/off switch and repeated manual operation outside of fault conditions may affect the breaker's calibrated trip threshold over time. A dedicated battery disconnect switch is recommended if a regular power isolation point is needed in the installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate RFCB100 100 Amp Circuit Breaker When a blown fuse at the wrong moment means a full rewire job, the RFCB100 replaces a standard fuse holder with a 100-amp manual-reset circuit breaker that gets your system back online without touching the wiring. Product Overview The RFCB100 is Rockford Fosgate's 100 Amp Circuit Breaker, designed to protect mid-power car audio amplifier systems from overcurrent events without the cost and downtime of replacing a blown fuse. Rated at 100 amps, it covers the protection requirements of single and dual-amplifier installations running 1/0 AWG or 4 AWG main power cable. All terminals are platinum plated for superior corrosion resistance and low-resistance electrical contact, and use a set-screw style connection that accepts bare wire directly without requiring ring terminals, simplifying installation and future servicing. When an overcurrent event occurs, the RFCB100 trips rather than blowing, and can be manually reset once the fault has been identified and cleared. The low-resistance, high-current design ensures minimal voltage drop across the breaker during normal operation, preserving maximum available voltage at the amplifiers. 1-year warranty. Features & Benefits Manual Reset Circuit Breaker: Unlike a fuse that must be replaced after an overcurrent event, the RFCB100 trips and can be manually reset once the fault condition has been resolved. This eliminates the need to carry spare fuses and allows the system to be restored to operation quickly in the field. 100 Amp Rating: Rated at 100 amps continuous, the RFCB100 provides the overcurrent protection threshold suited to mid-power single and dual-amplifier systems, including builds where combined amplifier fuse requirements fall at or below this rating. Platinum Plated Terminals: All connection terminals are platinum plated for superior corrosion resistance and low-resistance electrical contact, maintaining a clean, reliable connection over the life of the installation without the oxidation issues common to standard plated terminals. Set-Screw Style Connection: The set-screw terminal design accepts bare wire directly without requiring ring terminals or crimped lugs, reducing the number of connection points in the power run and simplifying both initial installation and future servicing. Multiple Wire Gauge Compatibility: Accepts 1/0 AWG and 4 AWG power cable, covering the wiring gauge requirements of mid-power car audio amplifier installations without requiring adaptor fittings. Low-Resistance, High-Current Design: Internal resistance is minimised to ensure negligible voltage drop across the breaker during normal operation, preserving the full supply voltage available from the battery and alternator for the amplifiers downstream. Technical Specs Specification Detail SKU RFCB100 Current Rating 100A Reset Type Manual Reset Terminal Plating Platinum Terminal Type Set-Screw (no ring terminals required) Wire Gauge Compatibility 1/0 AWG, 4 AWG Warranty 1 Year Goes Well With The RFCB100 is a direct replacement for the main power fuse or fuse holder in mid-power car audio installations. It is well matched to systems running a single 4-channel amplifier such as the R2-300X4 (60A) paired with a monoblock such as the R2-250X1 (50A), where the combined fuse requirement reaches 110A and a modest safety margin is appropriate, or any single mid-power amplifier build where the specified fuse rating falls comfortably at or below 100A. It sits in the main power cable run between the battery and the amplifier distribution point, installed as close to the battery as possible. For systems requiring 140A or 200A protection, the RFCB140 or RFCB200 are the appropriate step-up options. A 1/0 AWG or 4 AWG amplifier wiring kit is recommended depending on the total system power draw. Frequently Asked Questions What is the advantage of a circuit breaker over a standard blade or ANL fuse in a car audio system? A standard fuse is a one-time protection device that must be physically replaced after an overcurrent event, which can mean carrying spare fuses and a delay in restoring the system if a fault occurs away from home. A manual-reset circuit breaker like the RFCB100 trips when an overcurrent event occurs and can be reset by hand once the fault has been identified and cleared, restoring the system to operation without replacing any components. Does the RFCB100 require ring terminals for installation? No. The set-screw terminal design on the RFCB100 accepts bare wire directly, tightened into the terminal with the set screw. This removes the need for ring terminals or crimped lugs at the breaker connection points, reducing the number of potential resistance points in the power run and making installation and future servicing more straightforward. Where should the RFCB100 be installed in the power cable run? The RFCB100 should be installed in the positive power cable as close to the battery terminal as possible, within 30-45 cm of the battery in most installations. This placement ensures that the maximum length of power cable between the battery and the amplifiers is protected against overcurrent and short-circuit events. The negative or ground cable does not pass through the circuit breaker. How do I choose between the RFCB100, RFCB140, and RFCB200? Select the circuit breaker whose rating meets or modestly exceeds the combined fuse requirements of all amplifiers in the system. Add up the recommended fuse ratings for each amplifier: for example, the R2-300X4 specifies 60A and the R2-200X2 specifies 30A, giving a combined requirement of 90A, making the RFCB100 the correct match. The RFCB140 suits builds where the combined requirement falls between 101A and 140A, and the RFCB200 is matched specifically to the R2-1200X1's 200A fuse requirement or equivalent high-power multi-amplifier builds. Sizing the breaker too low relative to the combined draw will cause nuisance tripping, while sizing it too high reduces the effectiveness of the overcurrent protection. Can the RFCB100 be used as a main disconnect switch as well as a circuit breaker? The RFCB100 is a circuit breaker with manual reset capability, not a purpose-designed disconnect switch. While manually tripping the breaker will interrupt the power supply to the amplifiers, it is not rated or designed as a deliberate on/off switch and repeated manual operation outside of fault conditions may affect the breaker's calibrated trip threshold over time. A dedicated battery disconnect switch is recommended if a regular power isolation point is needed in the installation.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

12" 4-Ohm Dual Voice Coil Subwoofer 250W RMS, Mica-Injected Polypropylene Cone, StampCast Basket with Spider Venting, 12 AWG Compression Terminals. Product Overview The Rockford Fosgate Prime R2D4-12 is a 12" 4-Ohm Dual Voice Coil (DVC) subwoofer rated at 250W RMS the 12" 4-Ohm variant of the R2 series, combining the larger 12" cone with the 4-Ohm DVC wiring flexibility that suits a wider range of amplifier impedance ratings than the 2-Ohm DVC variant. The 4-Ohm DVC provides wiring options of 2-Ohm (parallel), 8-Ohm (series), or 4-Ohm per coil for bi-amplification. Optimised for sealed and vented enclosures. Sold as an individual unit. Construction is consistent across the R2 platform: mica-injected polypropylene cone, anodized aluminium voice coil former, linear spider with embedded 16 AWG tinsel leads, StampCast basket with integrated spider venting, 12 AWG compression terminals, and integrated PVC trim ring. Key Specifications Subwoofer size: 12 inch Voice coil configuration: Dual Voice Coil (DVC) Impedance: 4-Ohm per coil (2-Ohm parallel / 8-Ohm series / 4-Ohm biamp) Power handling (RMS): 250W (confirmed) Peak power: Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Xmax: Not specified — confirm with Rockford Fosgate Voice coil former: Anodized aluminium Cone: Mica-injected polypropylene Surround: Not specified — confirm with Rockford Fosgate Spider: Linear with embedded 16 AWG tinsel leads Basket: StampCast with integrated spider venting Input terminals: 12 AWG compression terminals Trim ring: Integrated PVC Enclosure compatibility: Sealed and vented ✓ Mounting depth: Not specified — confirm with Rockford Fosgate Cutout diameter: Not specified — confirm with Rockford Fosgate Sold as: Individual unit Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 12" Cone — Larger cone area than a 10" driver, moving more air per stroke for increased bass output and generally lower frequency extension. 250W RMS Power Handling — 250W RMS confirmed per the product description — the same sustained rating as the 12" R2D2-12 at the same power level. 4-Ohm DVC — Three Wiring Options: 2-Ohm (parallel): Maximum output from amplifiers rated stable at 2-Ohm 8-Ohm (series): Compatible with amplifiers having a minimum impedance above 4-Ohm 4-Ohm per coil (biamp): Each coil driven by a separate amplifier channel Mica-Injected Polypropylene Cone — Stiffened polypropylene for reduced cone flex and accurate bass reproduction with moisture resistance. StampCast Basket with Integrated Spider Venting — Ventilation openings in the basket cool the motor during sustained operation — a construction feature Rockford Fosgate notes is "typically reserved for more expensive models." Anodized Aluminium Voice Coil Former — Improved heat radiation over plain aluminium for extended thermal capacity. 12 AWG Compression Terminals — Secure, low-resistance wiring connection appropriate for 250W RMS operation. Linear Spider with Embedded 16 AWG Tinsel Leads — Consistent compliance and integrated leads for reduced flex fatigue at the connection point. Optimised for Sealed and Vented Enclosures — Both enclosure types confirmed. Technical Specs Specification Detail Brand Rockford Fosgate Part Number R2D4-12 Series Prime R2 Subwoofer Size 12 inch Voice Coil Dual Voice Coil (DVC) Impedance per Coil 4-Ohm ✓ Wiring Options 2-Ohm (parallel) / 8-Ohm (series) / 4-Ohm biamp ✓ Power Handling (RMS) 250W ✓ Peak Power Not specified Sensitivity Not specified — confirm with Rockford Fosgate Frequency Response Not specified — confirm with Rockford Fosgate Xmax Not specified — confirm with Rockford Fosgate Voice Coil Former Anodized Aluminium Cone Mica-Injected Polypropylene Surround Not specified — confirm with Rockford Fosgate Spider Linear, Embedded 16 AWG Tinsel Leads Basket StampCast with Integrated Spider Venting Input Terminals 12 AWG Compression Terminals Trim Ring Integrated PVC Enclosure Type Sealed and Vented ✓ Mounting Depth Not specified — confirm with Rockford Fosgate Cutout Diameter Not specified — confirm with Rockford Fosgate Sold As Individual Unit Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable enclosure types: Sealed — tight, accurate bass Vented — higher efficiency output at the tuning frequency Wiring configurations: 2-Ohm → both coils in parallel (common choice for maximum amplifier output) 8-Ohm → both coils in series 4-Ohm per coil → bi-amplification Pairs well with: Rockford Fosgate T1000-1BDCP, T1500-1BDCP, or T2500-1BDCP mono amplifiers at the appropriate wiring impedance Frequently Asked Questions What are the wiring options for the R2D4-12's 4-Ohm DVC? The 4-Ohm DVC provides three configurations: 2-Ohm (both coils in parallel — most common for maximum output), 8-Ohm (both coils in series — suits amplifiers with higher minimum impedance), and 4-Ohm per coil for bi-amplification with separate amplifier channels. What amplifier power is appropriate for the R2D4-12? 250W RMS matched at the selected wiring impedance. Confirm the amplifier's RMS output at 2-Ohm (parallel) or 8-Ohm (series) before purchasing. What enclosure volume is recommended? Enclosure volume and vent specifications are not confirmed in the supplier data. Pull the official Rockford Fosgate R2D4-12 datasheet for recommended sealed and vented volumes. Is this the same as the R2D2-12 but with different impedance? The R2D2-12 and R2D4-12 share the same 12" R2 platform and 250W RMS rating. The difference is the voice coil impedance: R2D2-12 is 2-Ohm per coil (1-Ohm parallel / 4-Ohm series), while the R2D4-12 is 4-Ohm per coil (2-Ohm parallel / 8-Ohm series). Select based on your amplifier's stable impedance rating and preferred wiring configuration. What is the advantage of 4-Ohm DVC over 2-Ohm DVC? The 4-Ohm DVC wires to 2-Ohm or 8-Ohm, which are more universally compatible with a wider range of amplifiers than the 2-Ohm DVC's 1-Ohm parallel option. Most amplifiers are rated stable at 2-Ohm; the 4-Ohm DVC at 2-Ohm parallel is the most common subwoofer wiring configuration in car audio installations. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

10" 4-Ohm Dual Voice Coil Subwoofer 250W RMS, Mica-Injected Polypropylene Cone, StampCast Basket, 12 AWG Compression Terminals. Sealed and Vented Compatible. Product Overview The Rockford Fosgate Prime R2D4-10 is a 10" 4-Ohm Dual Voice Coil (DVC) subwoofer rated at 250W RMS the R2 series step up from the R1, adding DVC wiring flexibility and a mica-injected polypropylene cone. The 4-Ohm DVC design provides three wiring options: 2-Ohm (parallel), 8-Ohm (series), or biamped per coil enabling the subwoofer to be matched to a wide range of mono amplifier impedance ratings. Optimised for both sealed and vented enclosures. The StampCast basket incorporates integrated spider venting for thermal management. The anodized aluminium voice coil former improves heat dissipation compared to plain or polished aluminium. Wiring connections are made via 12 AWG compression terminals a heavier gauge and more secure connection than standard push terminals. Sold as an individual unit. Key Specifications Subwoofer size: 10 inch Voice coil configuration: Dual Voice Coil (DVC) Impedance: 4-Ohm per coil (2-Ohm parallel / 8-Ohm series / 4-Ohm biamp) Power handling (RMS): 250W (confirmed) Peak power: Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Xmax: Not specified — confirm with Rockford Fosgate Voice coil former: Anodized aluminium Cone: Mica-injected polypropylene Surround: Not specified — confirm with Rockford Fosgate Spider: Linear with embedded 16 AWG tinsel leads Basket: StampCast with integrated spider venting Input terminals: 12 AWG compression terminals Trim ring: Integrated PVC Enclosure compatibility: Sealed and vented ✓ Mounting depth: Not specified — confirm with Rockford Fosgate Cutout diameter: Not specified — confirm with Rockford Fosgate Sold as: Individual unit Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 250W RMS Power Handling — 250W RMS is confirmed — 50W more than the R1 series R1S4-10 — providing greater headroom for amplified installations. Dual Voice Coil (DVC) — Three Wiring Configurations — The 4-Ohm DVC design provides three wiring options from a single subwoofer: 2-Ohm: Wire both coils in parallel — most amplifiers produce maximum output at 2-Ohm 8-Ohm: Wire both coils in series — useful for amplifiers with minimum impedance requirements above 4-Ohm 4-Ohm per coil: Connect each coil to a separate amplifier channel for bi-amplification This flexibility is the primary advantage of DVC over SVC subwoofers. Mica-Injected Polypropylene Cone — Mica particles added to the polypropylene cone compound increase structural stiffness without significant weight increase — producing a stiffer cone that resists flex under dynamic load for more accurate bass reproduction. Polypropylene provides moisture resistance. StampCast Basket with Integrated Spider Venting — Rockford Fosgate's StampCast basket construction incorporates integrated ventilation openings around the spider for airflow — cooling the motor structure during sustained operation. The supplier notes this venting feature is "typically reserved for more expensive models," indicating its inclusion is a specification step-up for the R2 price tier. Anodized Aluminium Voice Coil Former — The anodizing process on the aluminium former increases its surface emissivity — improving heat radiation away from the former into the surrounding air and magnet gap. More effective thermal management than plain or polished aluminium of equivalent dimensions. 12 AWG Compression Terminals — 12 AWG compression terminals accept larger gauge wiring than standard push terminals, provide a more secure physical grip on the wire, and minimise contact resistance at the connection point — all important for a subwoofer carrying the current demanded by 250W RMS operation. Linear Spider with Embedded 16 AWG Tinsel Leads — The linear spider provides consistent suspension compliance across the voice coil's excursion range. The 16 AWG tinsel leads are embedded into the spider fabric — securely integrated rather than attached as separate flexible wires, reducing flex fatigue failure at the connection point under sustained high-excursion operation. Optimised for Sealed and Vented Enclosures — Confirmed dual enclosure compatibility — sealed for tight, accurate bass; vented for higher efficiency output at the box tuning frequency. Technical Specs Specification Detail Brand Rockford Fosgate Part Number R2D4-10 Series Prime R2 Subwoofer Size 10 inch Voice Coil Dual Voice Coil (DVC) Impedance per Coil 4-Ohm ✓ Wiring Options 2-Ohm (parallel) / 8-Ohm (series) / 4-Ohm biamp ✓ Power Handling (RMS) 250W ✓ Peak Power Not specified Sensitivity Not specified — confirm with Rockford Fosgate Frequency Response Not specified — confirm with Rockford Fosgate Xmax Not specified — confirm with Rockford Fosgate Voice Coil Former Anodized Aluminium Cone Mica-Injected Polypropylene Surround Not specified — confirm with Rockford Fosgate Spider Linear, Embedded 16 AWG Tinsel Leads Basket StampCast with Integrated Spider Venting Input Terminals 12 AWG Compression Terminals Trim Ring Integrated PVC Enclosure Type Sealed and Vented ✓ Mounting Depth Not specified — confirm with Rockford Fosgate Cutout Diameter Not specified — confirm with Rockford Fosgate Sold As Individual Unit Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable enclosure types: Sealed (acoustic suspension) — tight, accurate bass Vented (ported/bass reflex) — higher efficiency output Wiring configurations: 2-Ohm load → wire both coils in parallel (most common for maximum amplifier output) 8-Ohm load → wire both coils in series 4-Ohm per coil → bi-amplified with two amplifier channels Pairs well with: Rockford Fosgate T1000-1BDCP, T1500-1BDCP, or T2500-1BDCP mono amplifiers at the appropriate impedance A sealed or vented 10" enclosure built or selected to Rockford Fosgate's recommended volume specifications Frequently Asked Questions What does Dual Voice Coil (DVC) mean and how does it help? A DVC subwoofer has two separate voice coils wound on the same former. Each coil has its own set of input terminals, and the two coils can be wired in different configurations to change the total impedance presented to the amplifier. The R2D4-10's 4-Ohm DVC can be wired to 2-Ohm (parallel), 8-Ohm (series), or 4-Ohm per coil for bi-amplification — giving the installer flexibility to match any mono amplifier's preferred or minimum load impedance. What amplifier power is correct for the R2D4-10? The R2D4-10 is rated at 250W RMS. Match the amplifier's rated RMS output at the intended wiring impedance to no more than 250W. If using the 2-Ohm parallel wiring, ensure the amplifier is rated stable at 2-Ohm and confirm its 2-Ohm RMS output is within the subwoofer's rating. What is the difference between sealed and vented enclosure performance? In a sealed enclosure the subwoofer works against a fixed volume of air — producing tight, accurate bass with a gradual roll-off below resonance. In a vented enclosure, a tuned port allows the air inside the box to reinforce bass output at the port tuning frequency — producing more output and greater efficiency at that frequency, but with a steeper roll-off below the tuning point. What enclosure volume is recommended for the R2D4-10? Enclosure volume, vent dimensions, and tuning frequency recommendations are not confirmed in the supplier data. Pull the official Rockford Fosgate R2D4-10 datasheet for the recommended net internal volume for sealed and vented designs. What is the advantage of 12 AWG compression terminals over push terminals? 12 AWG compression terminals accept thicker wire, grip it more securely via a mechanical compression mechanism, and provide lower contact resistance than spring-loaded push terminals. For a 250W subwoofer, the higher current demand makes a secure, low-resistance wiring connection more important — reducing the voltage drop and heat generation at the terminal. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate R2-750X5 Prime 750 Watt 5-Channel Full-Range Class-D Car Amplifier A 750W 5-channel Full-Range Class-D car amplifier delivering 100W x 4 plus 350W x 1 at 2-ohm (CTA-2006 rated). Features independent front, rear, and subwoofer channel crossover control, Continuously Variable Punch EQ, variable infrasonic filter, C.L.E.A.N. gain calibration with per-channel output clip indicators, Rollback Protection, NOMAD speaker protection, RLC remote level control, and 2/4/5 channel input selection. Designed and engineered in Tempe, Arizona. Backed by a 1 year warranty. Product Overview The Rockford Fosgate R2-750X5 is a 750W 5-channel Full-Range Class-D car amplifier from the Prime R2 series, providing a complete single-amplifier solution for powering both car speakers and a subwoofer from the one unit. Rated continuous power is 50W x 4 plus 200W x 1 at 4-ohm, or 100W x 4 plus 350W x 1 at 2-ohm (CTA-2006, less than 1.0% THD+N). Dynamic power via PowerCube reaches 70W x 4 plus 241W x 1 at 4-ohm, and 114W x 4 plus 426W x 1 at 2-ohm. The front and rear full-range channels can also be bridged to 200W x 2 at 4-ohm. The R2-750X5 provides fully independent crossover control for the front, rear, and subwoofer channels, each with their own high-pass and low-pass crossover adjustments at 12dB/octave Butterworth (50Hz-250Hz) plus a variable infrasonic filter on the subwoofer channel (15Hz-40Hz). A 2/4/5 channel input selection switch enables flexible integration with source units providing different numbers of RCA outputs, working for both RCA and high-level inputs. Three dedicated sets of RCA and high-level inputs cover front, rear, and subwoofer channels separately, with independent gain adjustment per channel group. C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) provides independent input and output clip indicators for front, rear, and subwoofer channel groups. A Continuously Variable onboard Punch EQ delivers up to 18dB of bass boost at 45Hz on the subwoofer channel. An RLC remote level control is included for in-cabin subwoofer volume adjustment. Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management are all active. Cast aluminium heatsink with convection cooling. Designed and engineered in Tempe, Arizona. Features & Benefits Complete 5-Channel Car Audio System in One Amplifier: The R2-750X5 powers front speakers, rear speakers, and a subwoofer from a single unit, making it a space-efficient and cost-effective solution for full car audio builds without the need for two separate amplifiers. Independent Crossover Control for Each Channel Group: Front, rear, and subwoofer channel groups each have independent high-pass and low-pass crossover controls at 12dB/octave Butterworth (50Hz-250Hz), plus a variable infrasonic filter (15Hz-40Hz) on the subwoofer channel and independent gain adjustment per group. 2/4/5 Channel Input Selection Switch: The input selection switch allows the R2-750X5 to integrate with source units providing 2, 4, or 5 channels of RCA output, working for both RCA and high-level inputs, removing the need for Y-cables in installations with fewer RCA outputs. Continuously Variable Punch EQ - Up to 18dB at 45Hz: The onboard Punch EQ provides up to 18dB of continuously adjustable bass boost at 45Hz on the subwoofer channel, enabling subwoofer output to be tuned to the acoustic environment without a separate EQ or DSP. Variable Infrasonic Filter - 15Hz to 40Hz Tunable: The subwoofer channel infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing precise low-frequency protection across different subwoofer drivers and enclosure types. C.L.E.A.N. Technology - Per-Channel Clip Monitoring: C.L.E.A.N. provides separate input and output clip indicator LEDs for front, rear, and subwoofer channel groups independently, enabling accurate gain calibration across all five channels. RLC Remote Level Control Included: An RLC remote level control is included for in-cabin subwoofer output adjustment without returning to the amplifier. Rollback Protection and NOMAD Speaker Protection: Rollback Protection dynamically manages output to prevent thermal stress on output devices during sustained high-output conditions. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. Technical Specs Specification Detail SKU R2-750X5 Number of Channels 5 (4 full-range + 1 subwoofer) Total Power 750W Rated Power - 4-ohm (CTA-2006, less than 1.0% THD+N) 50W x 4 + 200W x 1 Rated Power - 2-ohm (CTA-2006, less than 1.0% THD+N) 100W x 4 + 350W x 1 Rated Power - 4-ohm Bridged (CTA-2006) 200W x 2 (full-range channels) Dynamic Power - 4-ohm (PowerCube) 70W x 4 + 241W x 1 Dynamic Power - 2-ohm (PowerCube) 114W x 4 + 426W x 1 Dynamic Power - 4-ohm Bridged (PowerCube) 234W x 2 (full-range channels) Circuit Topology Full-Range Class-D Bridgeable Yes (full-range channels) Frequency Response 20 Hz - 20 kHz THD + Noise Less than 1.0% at 4-ohm and 2-ohm (all channels) Input Sensitivity Low-Level: 150mV - 4V / High-Level: 450mV - 12V Signal Input Front: 2 x RCA + 4-Pin Molex / Rear: 2 x RCA + 4-Pin Molex / Sub: 2 x RCA + 4-Pin Molex Input Selection 2/4/5 Channel Switch (RCA and High-Level) Tone Controls Punch EQ: 0 to +18dB at 45Hz (Continuously Variable, Sub channel) Front High-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Front Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Rear High-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Rear Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Sub Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Sub Infrasonic Filter 15 Hz - 40 Hz at 12dB/Octave Butterworth (Variable) Remote Controls Yes (RLC Remote Level Control included) Power Wire Gauge 4 AWG Power Input Connector Compression Terminal Block Speaker Wire Gauge 8 AWG Speaker Output Connector Compression Terminal Block Cooling Convection Heatsink Cast Aluminium Operating Voltage 9 - 16 VDC Recommended Fuse (not included) 120A Max Current Draw at 13.8V Sinewave 71A Visual Indicators Power: Blue / Protect: Red / C.L.E.A.N. In: Red / C.L.E.A.N. Out Front, Rear, Sub: Blue/Red Dimensions (H x W x D) 49 x 173 x 285mm (1.9 x 6.8 x 11.2 inch) CTA-2006 Compliant Yes Warranty 1 Year Compatible With / Goes Well With The R2-750X5 suits a wide range of car audio installations requiring a single-unit 5-channel amplifier solution for speakers and a subwoofer. The 2/4/5 channel input switch makes it compatible with most factory and aftermarket source units. Goes Well With: R2D2-12 / R2D2-10 - Rockford Fosgate Prime R2 series subwoofers, a matched Prime series pairing for the subwoofer channel R2-2X12 / R2-2X10 - Rockford Fosgate Prime dual loaded subwoofer enclosures for a complete drop-in bass solution RFK4 - Rockford Fosgate 4 AWG amplifier wiring kit to complete the installation DSR1 - Rockford Fosgate Digital Signal Processor for advanced signal processing ahead of the R2-750X5 Frequently Asked Questions What is the difference between the R2-750X5 and the M2-750X5? Both are 750W 5-channel Full-Range Class-D amplifiers with identical power ratings, the same 2/4/5 channel input switch, Punch EQ, variable infrasonic filter, and RLC remote. The M2-750X5 is from the M2 Element Ready marine series with conformal-coated PCB, UV stable powder-coated heatsink, zinc nickel-plated marine brass terminals, and Auto-Sense turn-on suited to marine and outdoor environments. The R2-750X5 is from the Prime R2 car audio series with a cast aluminium heatsink and standard car audio terminals. Choose the R2-750X5 for car audio; choose the M2-750X5 for marine or outdoor powersports applications. What does the 2/4/5 channel input selection switch do? The input selection switch configures the R2-750X5 to accept 2, 4, or 5 channels of RCA or high-level input. In 2-channel mode, the single front RCA pair feeds all five channels internally. In 4-channel mode, separate front and rear RCA pairs are used independently. In 5-channel mode, all three RCA input pairs (front, rear, sub) are used for full independent channel control. This removes the need for Y-cables when the source unit has fewer RCA outputs. What fuse does the R2-750X5 require and is it included? The R2-750X5 requires a 120A fuse, which is not included and must be sourced separately. Install the fuse as close to the battery as possible in the 4 AWG power supply line. The maximum sinewave current draw is 71A. Can I add a subwoofer to this amplifier without a separate mono amp? Yes. The R2-750X5 includes a dedicated subwoofer channel rated at 350W RMS at 2-ohm. This eliminates the need for a separate monoblock amplifier in most builds. The included RLC remote level control allows subwoofer volume to be adjusted from the cabin without accessing the amplifier. Is the R2-750X5 compatible with a factory OEM head unit? Yes. The high-level (speaker-level) inputs accept 450mV to 12V, allowing direct connection to OEM head unit speaker outputs without RCA outputs. The 2/4/5 channel input switch further simplifies integration by allowing the amplifier to work with source units that have limited or no RCA outputs.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate R2-750X1 Prime 750 Watt Mono Class-D Subwoofer Amplifier A 750W mono Class-D subwoofer amplifier rated at 750W x 1 at 1-ohm, 500W x 1 at 2-ohm, and 250W x 1 at 4-ohm (CTA-2006 rated). Features Continuously Variable Punch EQ with up to 18dB of bass boost at 45Hz, variable infrasonic filter, C.L.E.A.N. gain calibration, RCA pass-through outputs, RLC remote level control, Rollback Protection, NOMAD speaker protection, and MEHSA4 heat management. Designed and engineered in Tempe, Arizona. Backed by a 1 year warranty. Product Overview The Rockford Fosgate R2-750X1 is a 750W mono Class-D subwoofer amplifier from the Prime R2 series, designed for car audio builds requiring dedicated subwoofer amplification at a strong price-to-performance ratio. As a dedicated single-channel subwoofer amplifier, it operates across a frequency range of 20Hz-250Hz. Rated continuous power is 250W x 1 at 4-ohm, 500W x 1 at 2-ohm, and 750W x 1 at 1-ohm (CTA-2006, less than 1.0% THD+N). Dynamic power via PowerCube reaches 300W at 4-ohm, 545W at 2-ohm, and 830W at 1-ohm. The Continuously Variable onboard Punch EQ delivers up to 18dB of boost at 45Hz. The variable infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing adjustable protection for different subwoofer drivers and enclosure types. RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a second amplifier without degradation. An RLC remote level control is included for in-cabin subwoofer volume adjustment. High-level inputs (450mV-12V) allow direct integration with OEM head units without RCA outputs. Auto-Sense turn-on via high-level input is supported, with an Auto-Sense bypass switch for vehicles with Retained Accessory Power (RAP) systems. C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) input and output clip indicators guide precise gain calibration at setup. Rollback Protection dynamically manages output to prevent thermal stress on the output devices. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. MEHSA4 reduces MOSFET temperatures, lowers distortion, and extends output device life. Cast aluminium heatsink with convection cooling. Designed and engineered in Tempe, Arizona. Features & Benefits 750W at 1-Ohm - Maximum Subwoofer Output: The R2-750X1 delivers its maximum rated output of 750W at 1-ohm (830W dynamic), with stepped output of 500W at 2-ohm and 250W at 4-ohm, providing flexibility to match a wide range of subwoofer impedance configurations. Continuously Variable Punch EQ - Up to 18dB at 45Hz: The onboard Punch EQ provides up to 18dB of continuously adjustable bass boost at 45Hz, allowing subwoofer output to be tuned to the acoustic characteristics of the installation without a separate equaliser. Variable Infrasonic Filter - 15Hz to 40Hz Tunable: The infrasonic filter is tunable from 15Hz to 40Hz at 12dB/octave, providing flexible protection for different subwoofer drivers and enclosure types beyond what a fixed infrasonic filter can offer. RCA Pass-Through Outputs - Downstream Chaining: RCA pass-through outputs are active with both RCA and high-level input, allowing the signal to be passed to a downstream speaker amplifier such as the R2-750X5 without Y-cable noise. C.L.E.A.N. Technology - Precise Gain Calibration: C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) provides dedicated input and output clip indicator LEDs for precise gain calibration at setup, maximising output while minimising distortion. RLC Remote Level Control Included: An RLC remote level control is included for in-cabin subwoofer volume adjustment without returning to the amplifier. Rollback Protection and NOMAD Speaker Protection: Rollback Protection dynamically manages output during sustained high-output conditions to prevent thermal stress on the output devices. NOMAD provides real-time protection against shorted speaker wires and dangerously low impedances. High-Level OEM Input with Auto-Sense Turn-On: High-level inputs accept OEM head unit speaker outputs, with Auto-Sense activating the amplifier automatically when a signal is detected. A bypass switch is included for vehicles with RAP systems. Technical Specs Specification Detail SKU R2-750X1 Number of Channels 1 (Monoblock) Total Power 750W Rated Power - 4-ohm (CTA-2006, less than 1.0% THD+N) 250W x 1 Rated Power - 2-ohm (CTA-2006, less than 1.0% THD+N) 500W x 1 Rated Power - 1-ohm (CTA-2006, less than 1.0% THD+N) 750W x 1 Dynamic Power - 4-ohm (PowerCube) 300W x 1 Dynamic Power - 2-ohm (PowerCube) 545W x 1 Dynamic Power - 1-ohm (PowerCube) 830W x 1 Circuit Topology Class-D Bridgeable No Frequency Response 20 Hz - 250 Hz THD + Noise Less than 1.0% at 4-ohm, 2-ohm, and 1-ohm Input Sensitivity Low-Level: 150mV - 4V / High-Level: 450mV - 12V Signal Input 2 x RCA / 4-Pin Molex High-Level Signal Output 2 x RCA Pass-Thru (active with RCA or High-Level input) Tone Controls Punch EQ: 0 to +18dB at 45Hz (Continuously Variable) Low-Pass Crossover 50 Hz - 250 Hz at 12dB/Octave Butterworth Infrasonic Filter 15 Hz - 40 Hz at 12dB/Octave Butterworth (Variable) Remote Controls Yes (RLC Remote Level Control included) Auto-Sense Turn-On Yes (with RAP bypass switch) Power Wire Gauge 4 AWG Power Input Connector Compression Terminal Block Speaker Wire Gauge 8 AWG Speaker Output Connector Compression Terminal Block Cooling Convection Heatsink Cast Aluminium Operating Voltage 9 - 16 VDC Recommended Fuse (not included) 120A Max Current Draw at 13.8V Sinewave 71A Visual Indicators Power: Blue / Protect: Red / C.L.E.A.N. In: Red / C.L.E.A.N. Out: Blue/Red Dimensions (H x W x D) 49 x 173 x 255mm (1.9 x 6.8 x 10.1 inch) CTA-2006 Compliant Yes Warranty 1 Year Compatible With / Goes Well With The R2-750X1 suits car audio builds requiring a dedicated mono subwoofer amplifier at the Prime R2 price point. It pairs naturally with the R2-750X5 via its RCA pass-through outputs for a complete 5-channel plus dedicated mono system. Goes Well With: R2-2X12 / R2-2X10 - Rockford Fosgate Prime dual loaded subwoofer enclosures, a direct application pairing with the R2-750X1 at 2-ohm R2D2-12 / R2D2-10 - Prime R2 series individual subwoofers for custom enclosure builds R2-750X5 - Companion R2 series 5-channel amplifier for speaker amplification, chainable via the R2-750X1's RCA pass-through outputs RFK4 - Rockford Fosgate 4 AWG amplifier wiring kit to complete the installation DSR1 - Rockford Fosgate Digital Signal Processor for advanced signal processing ahead of the R2-750X1 Frequently Asked Questions What impedance gives the most power from the R2-750X1? The R2-750X1 delivers maximum rated output at 1-ohm (750W RMS, 830W dynamic). At 2-ohm the output is 500W RMS, and at 4-ohm it is 250W RMS. For maximum subwoofer output, a subwoofer or dual subwoofer configuration wired to a 1-ohm or 2-ohm total load is recommended. Contact us for advice on matching your subwoofer configuration to the correct impedance setting. What is the difference between the R2-750X1 and the R2-750X5? The R2-750X1 is a monoblock subwoofer amplifier with a single Class-D channel operating from 20Hz-250Hz, delivering up to 750W RMS at 1-ohm. The R2-750X5 is a 5-channel Full-Range Class-D amplifier delivering 100W x 4 plus 350W x 1 at 2-ohm, designed to power both speakers and a subwoofer from the one unit. In most builds, both are used together - the R2-750X5 for speakers and the R2-750X1 for the subwoofer, connected via the R2-750X1's RCA pass-through outputs. Can the R2-750X1 be used with a factory OEM head unit? Yes. The R2-750X1 includes high-level inputs (450mV-12V) for direct connection to OEM head unit speaker outputs without RCA outputs. Auto-Sense turn-on activates the amplifier automatically when a signal is detected on the high-level input, removing the need for a dedicated remote wire. A RAP bypass switch is also included. What fuse does the R2-750X1 require and is it included? The R2-750X1 requires a 120A fuse, which is not included and must be sourced separately. Install the fuse as close to the battery as possible in the 4 AWG power supply line. Does the R2-750X1 work with a dual voice coil subwoofer? Yes. A dual voice coil (DVC) subwoofer can be wired in parallel to achieve a 1-ohm or 2-ohm load depending on the coil impedance, allowing you to take advantage of the R2-750X1's maximum output at 1-ohm. Contact us for advice on the correct wiring configuration for your specific subwoofer. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

12" Prime R1 Stamped Steel Mesh Grille Insert Black. Designed for Prime R1 Subwoofers with Removable Trim Ring. Protects Against Cone and Surround Damage. Product Overview The Rockford Fosgate R1G-12 is a 12" stamped steel mesh grille insert in black designed for use with Prime R1 12" subwoofers that feature a removable trim ring. The grille inserts snugly into the R1 subwoofer's trim ring no additional hardware required. The trim ring (included with the subwoofer) holds the grille securely in position. Key Specifications Part number: R1G-12 Compatible size: 12 inch ✓ Compatible series: Prime R1 ✓ Grille type: Stamped mesh insert ✓ Material: Stamped steel ✓ Colour: Black ✓ Fitment: Inserts into R1 subwoofer trim ring ✓ Trim ring required: Yes — removable trim ring must be present on subwoofer ✓ Generation: Not specified (confirm compatible models with Rockford Fosgate) Protection: Surround and cone damage ✓ Compatible SKUs: Select Prime R1 12" subwoofers with removable trim ring — confirm with Rockford Fosgate Pack quantity: Not confirmed — confirm with Rockford Fosgate Dimensions: Not confirmed — confirm with Rockford Fosgate Weight: Not confirmed Warranty: Not confirmed — confirm with Rockford Fosgate Features & Benefits Prime R1 Platform — Easy Integration The R1G-12 integrates directly into the R1 subwoofer's existing trim ring structure — a clean, factory-matched installation without aftermarket fabrication. Stamped Steel Mesh — Physical Cone and Surround Protection The rigid mesh shields the mica-injected polypropylene R1 cone from physical contact with boot cargo — preventing the cone and surround damage that occurs in unprotected installations. Trim Ring Insertion — Easy Install Remove the trim ring from the subwoofer, insert the grille, re-secure. No tools required. Fully reversible. Requires Removable Trim Ring The R1G-12 requires the subwoofer to have a removable trim ring — confirm this feature is present on your specific R1 12" model before purchasing. Technical Specs Specification Detail Brand Rockford Fosgate Part Number R1G-12 Series Prime R1 Compatible Size 12 inch ✓ Compatible Series Prime R1 (removable trim ring models) ✓ Grille Type Stamped Mesh Insert ✓ Material Stamped Steel ✓ Colour Black ✓ Fitment R1 subwoofer trim ring insertion ✓ Trim Ring Required Yes — must be removable type ✓ Generation Not specified Compatible SKUs Select R1 12" models with removable trim ring (confirm with Rockford Fosgate) Pack Quantity Not confirmed Dimensions Not confirmed Weight Not confirmed Warranty Not confirmed Compatible With / Goes Well With Confirmed compatible platform: Prime R1 12" subwoofers with removable trim ring — confirm specific SKUs with Rockford Fosgate Frequently Asked Questions Does the trim ring come with the R1G-12? No — the grille inserts into the trim ring already on the R1 12" subwoofer. The R1G-12 is the grille insert only. The trim ring must be the removable type — confirm this with Rockford Fosgate for your specific R1 subwoofer model. How do I know if my R1 subwoofer has a removable trim ring? The product description specifies this grille is "designed for use with Prime R1 subwoofers with removable trim ring" — indicating not all R1 models may qualify. Confirm with Rockford Fosgate whether your specific R1 12" subwoofer SKU includes a removable trim ring. Can I use a Punch P1 grille (P1G-12) on an R1 subwoofer instead? No — the R1G-12 and P1G-12 use different trim ring dimensions corresponding to their respective subwoofer series. These are not interchangeable. Is the R1G-12 sold as a single unit or a pair? Pack quantity is not confirmed. Confirm from the official Rockford Fosgate R1G-12 product page before ordering. Are grille inserts available for other R1 subwoofer sizes? Other R1G size variants (R1G-10, R1G-8) may be available — confirm the full R1G range with Rockford Fosgate. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

55W RMS 6"×8" Oval Factory Replacement Silk Dome Tweeter, Integrated Crossover, Mounting Hardware Included. Product Overview The Rockford Fosgate Prime R168X2 is a 6"×8" oval 2-way full-range speaker rated at 55W RMS the highest RMS rating in the Rockford Fosgate Prime speaker range represented in this catalogue. Designed for factory speaker positions using the 6"×8" oval cutout common in Ford, Mazda, and selected other vehicles each speaker combines a vacuum polypropylene cone woofer with a flush-mounted silk dome tweeter and integrated tweeter crossover for a direct factory replacement without external crossover components. At 55W RMS, the R168X2 handles more power than the 6.5" and 6.75" Prime models making it a better match for amplified installations alongside the Rockford Fosgate Power series 4-channel amplifiers. The product description confirms the kit includes integrated crossovers and mounting hardware. Grilles are not referenced in the supplier data for this model confirm inclusion with Rockford Fosgate before purchasing if grilles are required for your installation. Key Specifications Speaker size: 6"×8" (oval) Configuration: 2-way full-range Power handling (RMS): 55W per speaker (confirmed) Peak power: Not specified — confirm with Rockford Fosgate Impedance: Not specified — confirm with Rockford Fosgate Sensitivity: Not specified — confirm with Rockford Fosgate Frequency response: Not specified — confirm with Rockford Fosgate Cone material: Vacuum polypropylene Surround: Rubber Basket: Stamped steel Tweeter: Silk dome, flush mounted Crossover: Integrated tweeter crossover (included) Mounting hardware: Included Grilles: Not confirmed in supplier data — confirm with Rockford Fosgate Pack contents: Single or pair — confirm with Rockford Fosgate (see Red-flags) Mounting depth: Not specified — confirm with Rockford Fosgate Cutout dimensions: Not specified — confirm with Rockford Fosgate Weight: Not specified — confirm with Rockford Fosgate Warranty: Not specified — confirm with Rockford Fosgate Features & Benefits 55W RMS — Highest in the Prime Speaker Range — At 55W RMS, the R168X2 handles 10W more continuously than the 6.5" and 6.75" Prime models — providing greater headroom for amplified installations and suiting it to the output of low-powered 4-channel amplifiers without requiring conservative gain settings. 6"×8" Oval Format — The 6"×8" oval format is a common OEM speaker size in Ford Falcon, Ford Focus, Ford Territory, Mazda 3, Mazda 6, and numerous other models where a standard round speaker will not fit. The larger oval cone area provides similar or better low-frequency output to a 6.5" round speaker while fitting the specific oval cutout of these vehicles. Silk Dome Flush-Mounted Tweeter — Smooth, warm high-frequency response from a soft silk dome tweeter — the same tweeter technology as the R14X2, R1525X2, and R1675X2, delivering consistent, non-fatiguing highs without the forward character of a Piezo design. Integrated Tweeter Crossover — Built-in crossover included in the kit — no external crossover required. Connects directly to factory speaker wiring. Vacuum Polypropylene Cone, Rubber Surround — Proven moisture-resistant construction for long-term reliability in Australian vehicle conditions. Technical Specs Specification Detail Brand Rockford Fosgate Part Number R168X2 Series Prime Speaker Size 6"×8" (oval) Configuration 2-Way Full-Range Power Handling (RMS) 55W per speaker ✓ Peak Power Not specified Sensitivity Not specified — confirm with Rockford Fosgate Frequency Response Not specified — confirm with Rockford Fosgate Tweeter Silk Dome, Flush Mounted Crossover Integrated (tweeter, included in kit) Cone Material Vacuum Polypropylene Surround Rubber Basket Stamped Steel Grilles Not confirmed — confirm with Rockford Fosgate Mounting Hardware Included Sold As Single or pair — confirm with Rockford Fosgate Impedance Not specified — confirm with Rockford Fosgate Mounting Depth Not specified — confirm with Rockford Fosgate Cutout Dimensions Not specified — confirm with Rockford Fosgate Weight Not specified — confirm with Rockford Fosgate Warranty Not specified — confirm with Rockford Fosgate Compatible With / Goes Well With Suitable installation positions: Factory 6"×8" oval door and panel speaker locations Vehicles with 6"×8" OEM oval cutouts — common in Ford, Mazda, and selected other makes and models Fitment caution: The 6"×8" oval is a specific cutout format — it is not interchangeable with round 6.5" or 6.75" positions. Confirm your vehicle uses a 6"×8" oval cutout before purchasing. Mounting depth and exact cutout dimensions should also be confirmed from the Rockford Fosgate datasheet before purchase. Rockford Fosgate Prime speaker range: Model Size Config RMS Tweeter Grilles R14X2 4" round 2-Way 30W ✓ Silk Dome ✓ R1525X2 5.25" round 2-Way TBC Silk Dome TBC R165X3 6.5" round 3-Way 45W ✓ Piezo ✓ R1675X2 6.75" round 2-Way 45W ✓ Silk Dome ✓ R168X2 6"×8" oval 2-Way 55W ✓ Silk Dome TBC Pairs well with: Rockford Fosgate T400-4, T600-4, or T1000-4AD 4-channel amplifiers 6"×8" oval speaker adaptors or baffles if required for cavity fit Frequently Asked Questions Is the 6"×8" format the same as a standard 6.5" speaker? No. The 6"×8" is an oval speaker format with a specific non-round cutout shape. It is not interchangeable with 6.5" or 6.75" round speaker positions without an adaptor. Confirm your vehicle's OEM speaker size and cutout format before purchasing. Are grilles included with the R168X2? The supplier description does not mention grilles for the R168X2 — unlike the other Prime series speakers which all confirm grille inclusion. Confirm whether grilles are included with Rockford Fosgate or your authorised reseller before purchasing if grilles are required for your installation. Is the R168X2 sold as a pair or single speaker? The supplier description refers to a "kit" with integrated crossovers and mounting hardware — suggesting a pair, consistent with the "X2" SKU suffix on other Prime models. However, pair status is not explicitly confirmed for the R168X2. Confirm with Rockford Fosgate before purchasing. What vehicles commonly use a 6"×8" oval speaker? The 6"×8" oval format is common in Ford Falcon, Focus, Territory, Mazda 3, Mazda 6, and a range of other Ford and Mazda platform vehicles. Always confirm your specific vehicle's speaker size using the owner's manual, a vehicle-specific fit guide, or a Rockford Fosgate fit guide before purchasing. Does the R168X2 need an amplifier? The 55W RMS rating is compatible with aftermarket head unit output, though sensitivity is not confirmed — confirm the sensitivity spec from the Rockford Fosgate datasheet to assess head unit compatibility. An amplifier from the Rockford Fosgate T series 4-channel range will maximise the speaker's performance headroom. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate R1-1X12 Prime Single 12" Sealed Loaded Enclosure Real Bass, Real Value Product Overview The Rockford Fosgate R1-1X12 is a single 12" sealed loaded enclosure from the Prime series, providing deep, controlled low bass response at an accessible price point. Housing a 12" subwoofer rated at 200 Watts and built with Rockford Fosgate's signature anodized aluminium voice coil former for superior power handling, it delivers a genuine step up in bass performance over generic loaded enclosures straight out of the box without any custom building or component sourcing required. Constructed from 5/8" MDF and finished in high-density carpet, the R1-1X12 is built for daily use in Australian vehicle boots, cargo areas, and under-seat spaces. Quick-release terminals allow the enclosure to be removed or repositioned quickly a practical feature for Australian ute and SUV owners who need flexibility in their cargo space. For buyers entering the Rockford Fosgate ecosystem on a budget, the R1-1X12 represents the most accessible 12" loaded enclosure in the Prime range with the engineering quality the brand is known for. Key Specifications Subwoofer: Single 12" Rockford Fosgate Prime R1 Power handling: 200W Enclosure type: Sealed Construction: 5/8" MDF Finish: High-density carpet Voice coil former: Anodized aluminium (Rockford Fosgate signature) Input terminals: High-current quick-release binding posts Dimensions: Confirm with supplier Shipping weight: Confirm with supplier Features & Benefits Single 12" Prime R1 subwoofer with anodized aluminium voice coil former: Rockford Fosgate's signature anodized aluminium voice coil former transfers heat away from the voice coil more efficiently than standard paper or plastic formers, delivering superior power handling at the 200W rating and better long-term reliability under sustained use. Sealed enclosure for deep, accurate low bass: The sealed design delivers the deep, tight, and controlled low bass response preferred for music genres and listening preferences where accuracy and low-frequency extension matter. A natural choice for Australian drivers who want clean, musical bass rather than loud, one-note output. 200W power handling: Accessible power requirements compatible with a wide range of entry-level and mid-range mono amplifiers. The most approachable power level in the Rockford Fosgate loaded enclosure catalogue ideal for first subwoofer installations and factory system upgrades. Quick-release terminals: Designed for fast enclosure removal and reinstallation without cutting wires. Practical for ute and SUV owners in Australia who regularly access boot storage or need to temporarily remove the subwoofer. 5/8" MDF construction: Rigid enclosure walls minimise panel flex and resonance, ensuring the sealed alignment performs as designed at sustained bass output levels. High-density carpet finish: Durable, professional appearance suited to daily boot and cargo area use in Australian vehicles. More resilient than standard carpet to the scrapes and abrasion common in working ute environments. Prime series value positioning: The R1-1X12 delivers Rockford Fosgate engineering including the signature anodized voice coil former at the most accessible price point in the Prime loaded enclosure range. A clear step up in quality from generic budget loaded enclosures available at similar price points. Plug-and-play loaded enclosure: Subwoofer and enclosure factory-assembled and ready to install. Connect power, ground, signal, and speaker wiring to a compatible amplifier and the system is operational no enclosure building, no driver installation, no tuning required. Technical Specs Specification Detail SKU R1-1X12 Brand Rockford Fosgate Subwoofer Driver 12" Rockford Fosgate Prime R1 Woofer Quantity 1 Power Handling 200W Enclosure Type Sealed Voice Coil Former Anodized aluminium Construction Material 5/8" MDF Finish High-density carpet Input Terminals High-current quick-release binding posts Impedance Confirm with supplier Dimensions Confirm with supplier Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Entry-level and mid-range mono amplifiers rated at or near 200W Rockford Fosgate Prime series mono amplifiers Sedans, hatchbacks, SUVs, and utes with available boot or cargo space Factory system upgrades via line output converter and compatible mono amplifier Rockford Fosgate wiring kits and RCA cables for amplifier integration First subwoofer installations and budget-conscious bass upgrades Frequently Asked Questions What amplifier does the R1-1X12 require? The R1-1X12 handles 200W. A mono amplifier rated at or near 200W at the enclosure's impedance is recommended. Confirm the pre-wired impedance with your supplier before selecting an amplifier to ensure correct matching. What is the advantage of the anodized aluminium voice coil former? Anodized aluminium conducts heat away from the voice coil more efficiently than paper or plastic formers, allowing the driver to handle its rated power more reliably over sustained use. It is a Rockford Fosgate signature feature that differentiates the R1 driver from generic budget subwoofers at a similar price point. Is the R1-1X12 sealed or vented? The R1-1X12 is a sealed enclosure. Sealed designs deliver deep, tight, and controlled bass response with good low-frequency extension preferred for listeners who prioritise bass accuracy and musicality over maximum volume output. How does the R1-1X12 compare to the Prime R2S shallow loaded enclosures? The R1-1X12 is a standard-depth sealed enclosure providing deep, accurate bass in a full boot or cargo area installation. The R2S-1X12 and R2S-1X10 are shallow sealed wedge enclosures designed for space-restricted behind-seat and under-seat installations. Choose the R1-1X12 for full bass performance where depth is available; choose an R2S model where mounting depth is severely restricted. Can the R1-1X12 be quickly removed from my vehicle? Yes. The R1-1X12 features quick-release terminals specifically designed for fast enclosure removal and reinstallation without cutting or reconnecting wires a practical feature for ute and SUV owners who regularly access boot storage space. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Rockford Fosgate PS-8 Punch 8" 150W Amplified Loaded Enclosure Compact Size, Serious Output Product Overview The Rockford Fosgate PS-8 is a self-contained amplified subwoofer system housing a single Punch 8" shallow woofer, a 150 Watt Class-D internal amplifier, and a custom sealed enclosure in one compact, low-profile unit. Designed for vehicles and installs where space and mounting height are severely restricted, the PS-8 delivers genuine Punch bass performance without the footprint of a traditional subwoofer and amplifier combination. The cast aluminium enclosure with ABS backplate keeps the PS-8 rigid, lightweight, and resistant to the heat and vibration common in Australian vehicle boot and under-seat environments. The closed-loop design ensures the 8" shallow woofer, Class-D amplifier, and sealed enclosure are tuned as a matched system for optimised performance. With hi-level and low-level inputs, a variable low-pass crossover, adjustable bass boost, a built-in 0°/180° phase switch, flexible turn-on options, and an included remote bass level control, the PS-8 is a complete, ready-to-install solution power, ground, and turn-on wiring and mounting hardware are all included in the box. Key Specifications Subwoofer: 8" Rockford Fosgate Punch proprietary shallow woofer Amplifier: Internal 150W RMS Class-D Enclosure type: Sealed (closed-loop) Frequency response: 25 Hz – 150 Hz Crossover: Variable 50 Hz – 120 Hz @ 12 dB/octave Butterworth Enclosure material: Cast aluminium with ABS backplate Heatsink: Cast aluminium; convection cooled Dimensions (H x W x D): 36.5 x 23.8 x 8.3 cm CEA-2031 compliant Remote bass control: Included Features & Benefits 150W RMS Class-D internal amplifier: Class-D topology delivers high efficiency with minimal heat generation, making it well-suited to shallow, space-restricted enclosures where thermal management is a key constraint. Draws less current from the vehicle's charging system than an equivalent Class-A/B amplifier. 8" shallow woofer in a sealed closed-loop enclosure: The shallow driver profile and sealed enclosure are engineered together as a matched system, producing controlled, punchy bass response across a 25 Hz to 150 Hz frequency range accurate and musical rather than boomy or one-note. Cast aluminium enclosure with ABS backplate: Unlike MDF-bodied competitors, the cast aluminium shell provides superior rigidity, heat dissipation, and resistance to the humidity, heat cycling, and vibration common in Australian vehicle boot and under-seat environments. Ultra-low profile at 8.3 cm depth: At just 83 mm deep, the PS-8 fits under seats, in shallow boot floors, behind panels, and into locations where even slim MDF enclosures will not. Purpose-built for modern Australian vehicles with limited cargo floor depth. Hi-level and low-level inputs: Connects to aftermarket head units via RCA (low-level) or directly to factory speaker outputs via hi-level inputs. Left and right high-level inputs are summed internally no additional line output converter required for factory system integration. Variable low-pass crossover (50 Hz – 120 Hz, 12 dB/octave Butterworth): Set the crossover frequency to match the capabilities of your existing full-range speakers, ensuring clean integration with no frequency overlap or gap in the audio spectrum. Built-in adjustable bass boost EQ: Add low-frequency emphasis to taste without an external equaliser. Useful for compensating for the natural bass roll-off in open-air, hatchback, and vehicles with acoustically compromised boot spaces. 0°/180° phase switch: Align the PS-8's output phase with your main speakers for coherent, integrated bass reproduction across all seating positions. Remote/DC offset/signal sense turn-on selection: Three turn-on methods in one unit. Use a remote turn-on wire, DC offset sensing, or signal sense whichever suits your specific head unit and installation type. Particularly useful for factory system integration where a remote wire is not always available. Remote bass level control included: Adjust bass output from the driver's seat without accessing the unit. Included in the box no additional purchase required. Short circuit, thermal, and reverse polarity protection: Three independent protection circuits guard the PS-8 against common installation errors and operating faults. Reverse polarity protection is especially valuable for DIY installs where wiring mistakes can occur. Quick disconnect power and signal connections: Removable connectors for power, ground, remote, and signal simplify installation and allow the unit to be removed and reinstalled cleanly without cutting wires. Complete wiring and mounting hardware included: Power wire, ground wire, turn-on wire, and mounting hardware are all in the box. Everything needed for a full installation without additional accessory purchases. CEA-2031 compliant: Power ratings comply with the CEA-2031 standard for amplified subwoofer systems, providing a verified, comparable power specification. Technical Specs Specification Detail SKU PS-8 Brand Rockford Fosgate Subwoofer Driver 8" Rockford Fosgate Punch proprietary shallow woofer Woofer Quantity 1 Internal Amplifier 150W RMS Circuit Topology Class-D Enclosure Type Sealed (closed-loop) Enclosure Material Cast aluminium with ABS backplate Heatsink Cast aluminium Cooling Convection Frequency Response 25 Hz – 150 Hz Crossover Variable 50 Hz – 120 Hz @ 12 dB/octave Butterworth Tone Controls Gain + adjustable bass boost EQ Phase Switch 0° / 180° Signal Input – Low Level 1 x RCA pair Signal Input – High Level Left/Right summed inputs Power Input Connector Removable connector (power/ground/remote) Turn-On Methods Remote wire / DC offset / signal sense Remote Bass Control Included Visual Indicators Power / Protect LED Protection Short circuit / thermal / reverse polarity Power Wire Included Ground Wire Included Turn-On Wire Included Mounting Hardware Included CEA-2031 Compliant Yes Dimensions (H x W x D) 36.5 x 23.8 x 8.3 cm Shipping Weight Confirm with supplier Warranty Confirm with supplier Compatible With Factory (OEM) head units via hi-level summed inputs and signal sense or DC offset turn-on Aftermarket head units via low-level RCA inputs and remote turn-on wire Vehicles with severely space-restricted installations: modern sedans, hatchbacks, SUVs, and utes with shallow boot floors Under-seat mounting applications in utes, dual-cabs, and SUVs Vehicles requiring a complete self-contained bass solution without a separate amplifier or enclosure Rockford Fosgate RCA cables and signal accessories for low-level integration Frequently Asked Questions Do I need a separate amplifier to run the PS-8? No. The PS-8 has a 150W RMS Class-D amplifier built directly into the enclosure. Connect power, ground, and an audio signal from your head unit or factory system and it is ready to use. Can the PS-8 connect directly to a factory head unit? Yes. The PS-8 features hi-level left and right summed inputs that connect directly to factory speaker outputs, and supports DC offset and signal sense turn-on no remote wire or aftermarket head unit required for factory system integration. How shallow is the PS-8 enclosure? The PS-8 is just 8.3 cm deep, making it one of the most space-efficient amplified subwoofer options available. At 36.5 x 23.8 x 8.3 cm overall, it fits under seats and in shallow boot floors where standard enclosures will not. What protection circuits does the PS-8 include? The PS-8 includes short circuit, thermal, and reverse polarity protection. Reverse polarity protection is particularly useful for DIY installations, preventing damage if power and ground connections are accidentally reversed. Is everything needed for installation included with the PS-8? Yes. The PS-8 ships with power wire, ground wire, turn-on wire, mounting hardware, and a remote bass level control everything required for a complete installation without additional accessory purchases in most standard vehicle setups. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less