Stinger HR9-NS001 9 Inch Complete Install Kit for Pioneer DMH-AP6650BT in Nissan Navara 2015 to 2019 SL ST STX with SWC Nav Outputs Reverse Camera and USB Retention The Stinger HR9-NS001 is a complete radio installation kit for fitting the Pioneer DMH-AP6650BT 9-inch head unit into the 2015 to 2019 Nissan Navara SL, ST, and STX (non-amplified models only). Includes a 9-inch flush-fit gloss black fascia, plug-and-play 20-pin and 32-pin to ISO wiring harness, steering wheel control interface, antenna adaptor, USB retention, and reverse camera retention. Navigation outputs including reverse, park, ignition, illumination, and VSS are provided, and the MFD clock can be set via the interface. Not compatible with factory-amplified variants or the factory 360-degree camera system. AUX retention is not included. The Pioneer DMH-AP6650BT head unit is not included. Product overview The HR9-NS001 is engineered specifically for the Navara's dash and factory wiring, covering everything needed for a clean installation of the Pioneer DMH-AP6650BT. The plug-and-play harness connects to the Navara's 20-pin and 32-pin factory connector configuration and converts to standard ISO with no splicing, soldering, or permanent wiring changes. The SWC interface retains factory steering wheel audio buttons on compatible aftermarket radios and holds its programming through power loss, so battery disconnection will not reset the setup. Navigation outputs covering reverse, park, ignition, illumination, and VSS signals allow proper navigation and safety feature integration with the Pioneer head unit. The interface also allows the Navara's multi-function display clock to be adjusted and set after installation. Reverse camera retention passes the standard factory camera signal to the Pioneer head unit. The 360-degree camera system is not supported. Factory USB is retained via the included harness; AUX is not retained. Factory amplifier retention is not supported. This kit suits non-amplified SL, ST, and STX grades only. Confirm your Navara's grade, audio configuration, and camera system before purchasing. Features and benefits 9-inch flush-fit gloss black fascia: Purpose-moulded for the Navara's dash for a factory-finish result around the Pioneer DMH-AP6650BT. Plug-and-play harness (20-pin and 32-pin to ISO): Connects to the Navara's factory connector configuration and converts to standard ISO with no splicing or permanent wiring changes. Steering wheel audio control retention: Retains factory steering wheel audio buttons with compatible aftermarket radios. SWC programming is retained through power loss. Full navigation outputs: Reverse, park, ignition, illumination, and VSS signal outputs for proper navigation and safety feature integration. MFD clock adjustment: Allows the Navara's multi-function display clock to be set after installation. Reverse camera retention: Passes the standard factory reverse camera signal to the Pioneer head unit. Not compatible with the 360-degree camera system. USB retention: Factory USB port retained via the included harness. AUX retention is not included. Antenna adaptor included: Factory FM/AM reception maintained without additional parts. Non-amplified models only: Not compatible with factory-amplified Navara variants. Factory amplifier is not retained. Head unit not included: The Pioneer DMH-AP6650BT is sold separately. Technical specs Specification Detail SKU HR9-NS001 Brand Stinger Colour Gloss black Vehicle Plug Style 20-pin and 32-pin Nissan connectors Output Standard ISO connector Fascia Size 9-inch flush fit Plug and Play Yes, factory to ISO, no splicing required Steering Wheel Audio Controls Retained (compatible aftermarket radios) SWC Memory Retained on power loss Navigation Outputs Reverse, park, ignition, illumination, VSS MFD Clock Adjustment Yes Reverse Camera Retention Yes, standard reverse camera only 360-Degree Camera Compatibility Not compatible USB Retention Yes, USB only AUX Retention Not included Antenna Adaptor Included Factory Amplifier Retention No Head Unit Compatibility Pioneer DMH-AP6650BT Compatible with Nissan Navara 2015 to 2019, SL, ST, and STX grades, non-amplified factory audio only. Not compatible with factory-amplified variants or vehicles fitted with the factory 360-degree camera system. Frequently asked questions Does the HR9-NS001 include the Pioneer DMH-AP6650BT head unit? No. The Pioneer DMH-AP6650BT is sold separately. The HR9-NS001 is the installation kit providing the fascia, harness, SWC interface, antenna adaptor, USB retention, and reverse camera retention needed to fit that head unit into compatible Navara models. Which Navara grades is this kit compatible with? This kit suits 2015 to 2019 Nissan Navara SL, ST, and STX grades with non-amplified factory audio. It is not compatible with factory-amplified variants or vehicles fitted with the factory 360-degree camera system. Will this kit retain my factory steering wheel controls and reverse camera? Yes to both. The SWC interface retains audio button functions with compatible aftermarket radios, and the reverse camera retention passes the standard factory camera signal to the Pioneer head unit. The 360-degree camera system is not supported. SWC programming is retained through power loss. What navigation outputs does this kit provide? The interface provides reverse, park, ignition, illumination, and VSS signal outputs to the Pioneer head unit. It also allows the Navara's multi-function display clock to be adjusted and set after installation. Is the factory USB port retained and what about AUX? Yes. USB is retained via the included harness, keeping the factory USB port functional with the Pioneer head unit. AUX retention is not included with this kit. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns, our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself, is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-SB001 9-Inch Trapezoid Radio Replacement Kit for Subaru Forester SH and Impreza 2007–2012 The Stinger HR9-SB001 is a radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Subaru Forester SH Series and Impreza (including WRX) from 2007 to 2012. The kit includes a 9-inch flush fit radio panel, steering wheel control retention interface with patch lead and antenna adaptor. This kit is for non-navigation models only, and phone button functions on the steering wheel are not retained even if the vehicle is equipped with them. Product overview The HR9-SB001 covers the Subaru Forester SH and Impreza GE, GH, GR and GV chassis from 2007 to 2012, including the WRX variant. The plug-and-play SWC interface connects to the factory 20-pin connector and retains the factory audio steering wheel controls with select aftermarket head units. Memory is retained after a power loss. A factory-to-aftermarket antenna adaptor is also included. Two fitment qualifiers apply to this kit. First, the HR9-SB001 is designed for non-navigation Forester and Impreza models only vehicles equipped with the factory navigation system are not compatible. Second, while the SWC interface retains audio controls, it does not retain the phone button functions on the steering wheel if the vehicle is equipped with them. Both of these points should be confirmed against the specific vehicle before purchasing. Features and benefits Covers Subaru Forester SH and Impreza GE/GH/GR/GV 2007–2012 including WRX: A single kit covers the Forester SH and the full Impreza chassis range of this generation including the WRX variant. Plug and play SWC retention: Connects directly to the factory 20-pin Subaru connector, retaining factory audio steering wheel controls with select aftermarket head units. Memory is retained even after a power loss. Phone buttons not retained: The SWC interface retains audio controls only. Steering wheel phone button functions are not retained if the vehicle is equipped with them. Antenna adaptor included: A factory-to-aftermarket antenna adaptor is included, covering the antenna connection without a separate purchase. Non-navigation models only: This kit is designed for Forester and Impreza models without the factory navigation system. Navigation-equipped models are not compatible. What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Antenna adaptor Technical specs Specification Detail SKU HR9-SB001 Brand Stinger Colour Black Compatible Vehicles Subaru Forester SH 2007–2012, Subaru Impreza (inc WRX) GE/GH/GR/GV 2007–2012 Head Unit Format 9" Trapezoid Vehicle Connectors 20-pin Subaru style SWC Interface Plug and play, memory retention Antenna Adaptor Included Reverse Camera Retention Not included AUX/USB Retention Not included Navigation Models Not compatible Phone Button Retention Not retained Sold As Bundle Compatible head units The HR9-SB001 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface Steering wheel phone buttons Not retained SWC memory retention Retained after power loss Factory antenna Retained via included adaptor Factory reverse camera Not included AUX/USB retention Not included Factory navigation Not compatible Frequently asked questions Is the HR9-SB001 compatible with Subaru Forester or Impreza models fitted with factory navigation? No. The HR9-SB001 is designed for non-navigation models only. If your Forester or Impreza is fitted with the factory navigation system, this kit is not suitable. Contact us for advice on an alternative solution for navigation-equipped models. Does the HR9-SB001 retain the steering wheel phone buttons? No. The SWC interface retains the factory audio steering wheel controls only. If your vehicle is equipped with steering wheel phone buttons, these functions will not be retained after installation of the HR9-SB001. Does the HR9-SB001 cover the Subaru WRX? Yes. The HR9-SB001 covers the Subaru Impreza including WRX variants across the GE, GH, GR and GV chassis from 2007 to 2012. The same navigation and phone button limitations apply. Does the HR9-SB001 include a reverse camera retention interface? No. Reverse camera retention is not included in this bundle. Contact us if you require a reverse camera retention solution for your Forester or Impreza. Which 9-inch trapezoid head units are compatible with the HR9-SB001? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Contact us for guidance on units not listed. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-SZ001 9-Inch Trapezoid Radio Replacement Kit for Suzuki Swift FZ Series 2011–2016 The Stinger HR9-SZ001 is a radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Suzuki Swift FZ Series from 2011 to 2016. The kit includes a 9-inch flush fit radio panel, steering wheel control retention interface with patch lead and antenna adaptor. Note that dash modification is required for installation and professional installation is strongly recommended. Product overview The HR9-SZ001 provides a plug-and-play installation solution for the Suzuki Swift FZ Series, connecting directly to the factory 20-pin connector and converting to a standard ISO connector without cutting or modification to the vehicle wiring. The SWC interface retains the factory audio steering wheel controls with select aftermarket head units. Unlike the HR9-SZ002 and HR9-SZ003 kits for later Swift generations, this bundle does not include a reverse camera retention interface or AUX/USB retention. An important note applies to this installation: dash modification is required as part of the installation process for the Swift FZ Series. Professional installation by a qualified car audio installer is strongly recommended. Features and benefits Radio replacement bundle for Suzuki Swift FZ 2011–2016: Combines a flush fit radio panel, plug-and-play SWC retention interface and antenna adaptor for the Swift FZ Series in a single kit. Plug and play SWC retention: Connects directly to the factory 20-pin Suzuki connector, retaining factory audio steering wheel controls with select aftermarket head units. Antenna adaptor included: A factory-to-aftermarket antenna adaptor is included, covering the antenna connection without a separate purchase. Dash modification required: Installation of the HR9-SZ001 into the Suzuki Swift FZ Series requires dash modification. Professional installation by a qualified car audio installer is strongly recommended. Plug and play factory connector compatibility: Connects to the Swift FZ's 20-pin factory connector, converting to a standard ISO connector without cutting or splicing. What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Antenna adaptor Technical specs Specification Detail SKU HR9-SZ001 Brand Stinger Colour Black Compatible Vehicles Suzuki Swift FZ Series 2011–2016 Head Unit Format 9" Trapezoid Vehicle Connectors 20-pin Suzuki style SWC Interface Plug and play Antenna Adaptor Included Reverse Camera Retention Not included AUX/USB Retention Not included Installation Note Dash modification required Sold As Bundle Compatible head units The HR9-SZ001 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface Factory antenna Retained via included adaptor Factory reverse camera Not included AUX/USB retention Not included Frequently asked questions What dash modification is required when installing the HR9-SZ001? The HR9-SZ001 installation into the Suzuki Swift FZ Series requires dash modification, however the specific nature of this modification is not fully detailed in the current product data. Contact us before beginning the installation and we can provide further guidance. Professional installation by a qualified car audio installer is strongly recommended. Does the HR9-SZ001 retain the factory steering wheel audio controls? Yes. The plug-and-play SWC interface retains the factory audio steering wheel controls with select aftermarket head units. Does the HR9-SZ001 include a reverse camera retention interface? No. Unlike later Suzuki Swift installation kits in the Stinger range, the HR9-SZ001 does not include a reverse camera retention interface. If your Swift FZ has a factory reverse camera and you wish to retain it, contact us for advice on a suitable solution. Does the HR9-SZ001 fit all Suzuki Swift FZ Series variants from 2011 to 2016? The HR9-SZ001 is confirmed for the Suzuki Swift FZ Series from 2011 to 2016. If you are unsure whether your specific variant or build date is covered, contact us before purchasing. Which 9-inch trapezoid head units are compatible with the HR9-SZ001? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Contact us for guidance on units not listed. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-SZ002 9-Inch Trapezoid Radio Replacement Kit for Suzuki Swift AZ Series 2017–2023 and Swift Sport 2023–2025 The Stinger HR9-SZ002 is a complete radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Suzuki Swift AZ Series from 2017 to 2023 and the Suzuki Swift Sport AZ from 2023 to 2025. The kit includes a 9-inch flush fit radio panel, steering wheel control retention interface with patch lead, antenna adaptor and reverse camera retention interface. Note that AUX and USB retention is not included, and in some instances the reverse camera retention interface will require modification or rewiring. Product overview The HR9-SZ002 provides a plug-and-play installation solution for the Suzuki Swift AZ Series and Swift Sport AZ, connecting directly to the factory 20-pin connector without cutting or modification to the vehicle wiring. Coverage spans the Swift AZ from 2017 to 2023 and extends to the Swift Sport AZ from 2023 to 2025, making the HR9-SZ002 the correct kit across a wide slice of the current Suzuki Swift generation. The SWC interface retains the factory audio steering wheel controls with select aftermarket head units and holds its programmed memory even after a power loss. An important installation caution applies to the reverse camera interface: in some Swift AZ configurations the interface harness pinout may differ from the factory harness, requiring modification or rewiring before the camera will operate correctly. Always compare the interface harness to the factory harness before connecting. AUX and USB retention is not included in this bundle and must be sourced separately if required. Features and benefits Covers Suzuki Swift AZ 2017–2023 and Swift Sport AZ 2023–2025: A single kit covers both the standard Swift AZ and the Swift Sport AZ across the confirmed vehicle application guide, providing a consistent installation solution for both variants. Plug and play SWC retention: Connects directly to the factory 20-pin Suzuki connector, retaining factory audio steering wheel controls with select aftermarket head units. Memory is retained even after a power loss. Reverse camera retention interface included: The factory reverse camera is supported via the included retention interface. In some instances the interface harness may require modification or rewiring — always compare to the factory harness before connecting. Antenna adaptor included: A factory-to-aftermarket antenna adaptor is included, covering the antenna connection without a separate purchase. AUX and USB retention not included: AUX and USB factory connection retention is not part of this bundle. Source separately if retention of these inputs is required. Plug and play factory connector compatibility: Connects directly to the Swift AZ's 20-pin factory connector without cutting, splicing or modification to the vehicle wiring. What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Antenna adaptor Reverse camera retention interface Technical specs Specification Detail SKU HR9-SZ002 Brand Stinger Colour Black Compatible Vehicles Suzuki Swift AZ 2017–2023, Suzuki Swift Sport AZ 2023–2025 Head Unit Format 9" Trapezoid Vehicle Connectors 20-pin Suzuki style SWC Interface Plug and play, memory retention Antenna Adaptor Included Reverse Camera Retention Included modification may be required in some instances AUX/USB Retention Not included Sold As Bundle Compatible head units The HR9-SZ002 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface SWC memory retention Retained after power loss Factory reverse camera Retained via included interface modification may be required Factory antenna Retained via included adaptor AUX/USB retention Not included Frequently asked questions Does the HR9-SZ002 cover both the Suzuki Swift and Swift Sport? Yes. The HR9-SZ002 covers the Suzuki Swift AZ Series from 2017 to 2023 and the Suzuki Swift Sport AZ from 2023 to 2025. If you are unsure whether your specific variant or build date is covered, contact us before purchasing. Why might the reverse camera retention interface need to be modified or rewired? In some Suzuki Swift AZ configurations the pinout of the factory reverse camera harness differs from the standard interface harness supplied. Always compare the interface harness connector to the factory harness before connecting. If a mismatch is found, rewiring of the interface harness pins will be required before the camera will operate correctly. Professional installation is recommended if you are unsure. Does the HR9-SZ002 retain the factory steering wheel audio controls? Yes. The plug-and-play SWC interface retains the factory audio steering wheel controls with select aftermarket head units. The interface also retains its programmed memory after a power loss. Does the HR9-SZ002 include AUX or USB retention? No. AUX and USB retention is not included in this bundle. If you require retention of these factory inputs, a separate AUX/USB retention harness must be sourced. Contact us for compatible accessories for the Swift AZ. Which 9-inch trapezoid head units are compatible with the HR9-SZ002? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Contact us for guidance on units not listed. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-SZ003 9-Inch Trapezoid Radio Replacement Kit for Suzuki Vitara LY Series 2015–2024 The Stinger HR9-SZ003 is a complete radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Suzuki Vitara LY Series from 2015 to 2024. The kit includes a 9-inch flush fit radio panel, steering wheel control retention interface with patch lead, antenna adaptor and reverse camera retention interface. Note that in some instances the reverse camera retention interface will require modification or rewiring compare the interface harness to the factory harness before connecting. Product overview The HR9-SZ003 provides a plug-and-play installation solution for the Suzuki Vitara LY Series, connecting directly to the factory 20-pin connector without cutting or modification to the vehicle wiring. The SWC interface retains the factory audio steering wheel controls with select aftermarket head units and holds its programmed memory even after a power loss. A factory-to-aftermarket antenna adaptor is included, and reverse camera retention is provided via the included interface. One installation caution applies to the reverse camera interface: in some Vitara LY configurations the interface harness pinout may differ from the factory harness, requiring modification or rewiring before connection. Always compare the interface harness to the factory harness before connecting. If you are unsure, professional installation by a qualified car audio installer is recommended. Features and benefits Complete radio replacement bundle for Suzuki Vitara LY 2015–2024: Combines a flush fit radio panel, plug-and-play SWC retention interface, antenna adaptor and reverse camera retention interface for the Vitara LY Series in a single kit. Plug and play SWC retention: Connects directly to the factory 20-pin Suzuki connector, retaining factory audio steering wheel controls with select aftermarket head units. Memory is retained even after a power loss. Reverse camera retention interface included: The factory reverse camera is supported via the included retention interface. Note that in some instances the interface harness may require modification or rewiring always compare to the factory harness before connecting. Antenna adaptor included: A factory-to-aftermarket antenna adaptor is included, covering the antenna connection without a separate purchase. Plug and play factory connector compatibility: Connects directly to the Vitara LY's 20-pin factory connector without cutting, splicing or modification to the vehicle wiring. What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Antenna adaptor Reverse camera retention interface Technical specs Specification Detail SKU HR9-SZ003 Brand Stinger Colour Black Compatible Vehicles Suzuki Vitara LY Series 2015–2024 Head Unit Format 9" Trapezoid Vehicle Connectors 20-pin Suzuki style SWC Interface Plug and play, memory retention Antenna Adaptor Included Reverse Camera Retention Included modification may be required in some instances Sold As Bundle Compatible head units The HR9-SZ003 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface SWC memory retention Retained after power loss Factory reverse camera Retained via included interface modification may be required Factory antenna Retained via included adaptor Frequently asked questions Why might the reverse camera retention interface need to be modified or rewired? In some Suzuki Vitara LY configurations the pinout of the factory reverse camera harness differs from the standard interface harness supplied. Always compare the interface harness connector to the factory harness before connecting. If a mismatch is found, rewiring of the interface harness pins will be required before the camera will operate correctly. Professional installation is recommended if you are unsure. Does the HR9-SZ003 retain the factory steering wheel audio controls? Yes. The plug-and-play SWC interface retains the factory audio steering wheel controls with select aftermarket head units. The interface also retains its programmed memory after a power loss. Does the HR9-SZ003 fit all Suzuki Vitara LY Series variants from 2015 to 2024? The HR9-SZ003 is confirmed for the Suzuki Vitara LY Series from 2015 to 2024. If you are unsure whether your specific variant or build date is covered, contact us before purchasing. Does the HR9-SZ003 include AUX or USB retention? AUX and USB retention is not confirmed as included in this bundle. Contact us if you require retention of these factory inputs for your Vitara installation. Which 9-inch trapezoid head units are compatible with the HR9-SZ003? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-TY003 9-Inch Trapezoid Radio Replacement Kit for Toyota RAV4 XA40 Series 2014–2018 The Stinger HR9-TY003 is a complete radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Toyota RAV4 XA40 Series from 2014 to 2018. The kit includes a 9-inch flush fit radio panel, steering wheel control retention interface, antenna adaptor, reverse camera retention interface and AUX/USB retention. Note that this kit is not compatible with RAV4 models equipped with the JBL sound system, and the fascia presents a 2mm step against the left-hand side air vent. Product overview The HR9-TY003 is one of the most comprehensive installation bundles in the Stinger range, covering the key factory feature retention requirements for the Toyota RAV4 XA40 in a single kit. The plug-and-play SWC interface retains the factory steering wheel audio controls and provides a reverse trigger output, while the reverse camera retention interface keeps the factory reverse camera operational with the aftermarket head unit. AUX and USB retention is also included, preserving the factory USB and auxiliary input connections. One important exclusion to note: the HR9-TY003 is not compatible with RAV4 XA40 models fitted with the JBL premium sound system, as the factory amplifier is not retained by this kit. Additionally, due to the dash geometry of the XA40, the fascia will present a 2mm step against the left-hand side air vent after installation. This is a known characteristic of this application. Features and benefits Complete radio replacement bundle: Combines a flush fit radio panel, SWC retention interface, antenna adaptor, reverse camera retention interface and AUX/USB retention in a single kit for the Toyota RAV4 XA40 2014–2018. Plug and play SWC retention: The steering wheel audio control interface connects directly to the factory RAV4 wiring without cutting or splicing, retaining factory audio controls with select aftermarket head units. Memory is retained even after a power loss. Reverse camera retention interface included: The factory reverse camera is retained and operational with the aftermarket head unit via the included retention interface. AUX and USB retention included: Factory AUX and USB connections are retained after the head unit upgrade via the included retention harness. Antenna adaptor included: A factory-to-aftermarket antenna adaptor is included, covering the antenna connection without requiring a separate purchase. Not compatible with JBL system models: This kit does not retain the factory amplifier and is not suitable for RAV4 XA40 variants fitted with the JBL sound system. 2mm step at left-hand side air vent: Due to the XA40 dash geometry, the fascia will sit with a 2mm step against the left-hand side air vent after installation.  What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Antenna adaptor Reverse camera retention interface AUX and USB retention harness Technical specs Specification Detail SKU HR9-TY003 Brand Stinger Colour Black Compatible Vehicles Toyota RAV4 XA40 Series 2014–2018 Head Unit Format 9" Trapezoid Vehicle Connectors 28-pin, 10-pin and 6-pin Toyota style SWC Interface Plug and play, memory retention Reverse Trigger Provided Antenna Adaptor Included AUX/USB Retention AUX and USB included Reverse Camera Retention Included Factory Amplifier Retention Not retained JBL System Compatibility Not compatible Installation Note 2mm step at left-hand side air vent Sold As Bundle Compatible head units The HR9-TY003 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface SWC memory retention Retained after power loss Reverse trigger output Provided Factory reverse camera Retained via included retention interface Factory antenna Retained via included adaptor AUX input Retained via included harness USB input Retained via included harness Factory amplifier Not retained Frequently asked questions Is the HR9-TY003 compatible with Toyota RAV4 models fitted with the JBL sound system? No. The HR9-TY003 does not retain the factory amplifier and is not compatible with RAV4 XA40 models equipped with the JBL premium sound system. If your RAV4 has the JBL system, contact us for advice on a suitable alternative installation approach. What is the 2mm step at the left-hand side air vent? Due to the dash geometry of the Toyota RAV4 XA40 Series, the fascia will not sit fully flush against the left-hand side air vent after installation, resulting in a visible 2mm step. This is a known characteristic of this application.  Does the HR9-TY003 retain the factory reverse camera? Yes. The reverse camera retention interface is included in the bundle, allowing the factory reverse camera to remain operational with the aftermarket head unit. Does the HR9-TY003 retain the factory steering wheel audio controls? Yes. The plug-and-play SWC interface retains the factory audio steering wheel controls with select aftermarket head units. The interface also retains its programmed memory after a power loss. Which 9-inch trapezoid head units are compatible with the HR9-TY003? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-VW001 9-Inch Trapezoid Radio Replacement Kit for Volkswagen Golf 2009–2013 The Stinger HR9-VW001 is a complete radio replacement bundle designed for the installation of a 9-inch trapezoid aftermarket head unit into the Volkswagen Golf from 2009 to 2013. The kit includes a 9-inch flush fit radio panel and a steering wheel control retention interface with patch lead. Note that this kit is not compatible with Golf models equipped with the factory amplifier. Product overview Installing a 9-inch trapezoid head unit into a Volkswagen Golf MK6 requires more than a fascia panel alone. The HR9-VW001 brings together the essential installation components into a single bundle, pairing a purpose-built 9-inch flush fit radio panel with a plug-and-play steering wheel control retention interface. The SWC interface retains the factory audio steering wheel buttons after the head unit upgrade, removing the need to source a separate SWC solution for this vehicle. The bundle also provides navigation outputs including Reverse, Park and VSS signals, and the SWC interface retains memory even if power is lost. One important compatibility note: the HR9-VW001 is not suitable for Golf MK6 models fitted with the factory amplifier. Confirm your vehicle's factory audio configuration before purchasing. Features and benefits Complete radio replacement bundle: Combines a 9-inch flush fit radio panel with a steering wheel control retention interface and patch lead in a single kit, covering the core installation requirements for the Volkswagen Golf 2009–2013. 9-inch flush fit radio panel: Purpose-built for the Golf MK6 dash opening, providing a clean, factory-matched flush fit for a 9-inch trapezoid head unit. Plug and play SWC retention interface: The steering wheel control interface connects directly to the factory Golf wiring without cutting or splicing, retaining the factory audio steering wheel buttons with the aftermarket head unit. Memory retention: The SWC interface retains its programmed settings even when power is lost, avoiding the need for reprogramming after a battery disconnect. Navigation outputs: Provides Reverse, Park and VSS outputs, supporting navigation-related functions of compatible aftermarket head units. Not compatible with factory amplifier models: This kit is designed for standard Golf MK6 audio configurations only. Vehicles fitted with the factory amplifier require a different installation solution. What's in the box 9" flush fit radio panel Steering wheel control retention interface SWC patch lead Technical specs Specification Detail SKU HR9-VW001 Brand Stinger Compatible Vehicles Volkswagen Golf MK6 2009–2013 Head Unit Format 9" Trapezoid SWC Interface Plug and play, memory retention Navigation Outputs Reverse, Park, VSS Factory Amplifier Not compatible Sold As Bundle (panel, SWC interface, patch lead) Compatible head units The HR9-VW001 is confirmed compatible with the following 9-inch trapezoid head units: Brand Model Alpine INE-AW409S Alpine INE-AX809 Kenwood DMX80AXS Mongoose Q9WCA Pioneer DMH-AP6650BT Aerpro AM9X Vehicle feature retention Feature Status Steering wheel audio controls Retained via included SWC interface SWC memory retention Retained after power loss Reverse output Provided Park output Provided VSS output Provided Frequently asked questions Is the HR9-VW001 compatible with Volkswagen Golf models fitted with a factory amplifier? No. The HR9-VW001 is not compatible with Golf MK6 models equipped with the factory amplifier. If your vehicle has a factory amplifier, a different installation solution will be required. Contact us with your vehicle details and we can advise on the correct approach. Does the HR9-VW001 retain the factory steering wheel audio controls? Yes. The included plug-and-play SWC retention interface retains the factory audio steering wheel buttons after the head unit upgrade. The interface also retains its programmed memory even if power is lost. Does the HR9-VW001 include a wiring harness or antenna adaptor? The HR9-VW001 includes the flush fit radio panel, SWC retention interface and patch lead. A full ISO wiring harness and antenna adaptor are not confirmed as included and must be purchased separately to complete the installation. Which 9-inch trapezoid head units are compatible with the HR9-VW001? Confirmed compatible units include Alpine INE-AW409S and INE-AX809, Kenwood DMX80AXS, Mongoose Q9WCA, Pioneer DMH-AP6650BT and Aerpro AM9X. Contact us for guidance on units not listed. Does the HR9-VW001 fit all Volkswagen Golf MK6 variants from 2009 to 2013? The HR9-VW001 is listed for the Volkswagen Golf MK6 from 2009 to 2013, excluding models fitted with the factory amplifier. If you are unsure whether your specific variant is covered, contact us before purchasing. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger HR9-TY001 9 Inch Radio Replacement Kit for Pioneer DMH-AP6650BT in Select Toyota Models 2005 to 2012 with Steering Wheel Control Retention The Stinger HR9-TY001 is a radio installation kit for fitting the Pioneer DMH-AP6650BT 9-inch head unit into compatible Toyota vehicles from 2005 to 2012 with a factory 200mm head unit opening. Includes a 9-inch flush-fit fascia and a plug-and-play steering wheel control interface. Connects to Toyota's factory 20-pin, 10-pin, and 6-pin connectors and converts to a standard ISO plug with no splicing or permanent wiring changes. SWC retention applies to models with the 20-pin connector only. No antenna adaptor or reverse camera retention is included. The Pioneer DMH-AP6650BT head unit is not included. Product overview The HR9-TY001 provides the fascia and SWC interface required to install the Pioneer DMH-AP6650BT in compatible Toyota models with a 200mm factory head unit opening and the Toyota 20-pin, 10-pin, and 6-pin connector configuration. The plug-and-play harness connects directly to the factory loom and converts to standard ISO without cutting, splicing, or soldering. Steering wheel audio control retention applies to Toyota models fitted with the 20-pin connector. The SWC interface retains its programming through power loss, so a battery disconnect or flat battery will not reset the setup. Note that an antenna adaptor is not included and will need to be sourced separately if required by the vehicle. Reverse camera retention is also not included. On some vehicles the head unit will sit forward of the factory dash panel, and fascia bracket modification may be required. Professional installation is recommended if fitment depth is a concern for a specific vehicle. Confirm your vehicle's factory head unit opening size and connector type before purchasing. The Pioneer DMH-AP6650BT is sold separately. Features and benefits 9-inch flush-fit fascia: Designed around Toyota's 200mm factory head unit opening for a purpose-built result with the Pioneer DMH-AP6650BT. Plug-and-play harness: Connects to Toyota's factory 20-pin, 10-pin, and 6-pin loom and converts to standard ISO. No splicing, soldering, or permanent wiring changes required. Steering wheel audio control retention: Retains factory steering wheel audio buttons on models fitted with the 20-pin connector. SWC memory retention on power loss: The interface stores its programming when disconnected from battery power, keeping settings intact through battery changes and workshop visits. No antenna adaptor included: A separate antenna adaptor may be required depending on the vehicle. No reverse camera retention included: Additional product may be required for reverse camera integration. Head unit not included: The Pioneer DMH-AP6650BT is sold separately. Technical specs Specification Detail SKU HR9-TY001 Brand Stinger Colour Black Vehicle Plug Style 20-pin, 10-pin, and 6-pin Toyota connectors Output Standard ISO connector Fascia Size 9-inch flush fit Factory Opening Required 200mm Plug and Play Yes, factory to ISO, no splicing required Steering Wheel Audio Controls Retained (20-pin connector models only) SWC Memory Retained on power loss Reverse Camera Retention Not included Antenna Adaptor Not included Fascia Bracket Modification May be required on some vehicles Head Unit Fitment Depth May sit forward of factory dash panel on some vehicles Head Unit Compatibility Pioneer DMH-AP6650BT Compatible with Select Toyota models 2005 to 2012 with a factory 200mm head unit opening and Toyota 20-pin, 10-pin, and 6-pin connector configuration. Confirm your vehicle's factory opening size and connector type before purchasing. Frequently asked questions Does the HR9-TY001 include the Pioneer DMH-AP6650BT head unit? No. The Pioneer DMH-AP6650BT is sold separately. The HR9-TY001 is the installation kit providing the fascia and SWC interface needed to fit that head unit into compatible Toyota models. Which Toyota models is the HR9-TY001 compatible with? This kit suits select Toyota models from 2005 to 2012 with a factory 200mm head unit opening and the Toyota 20-pin, 10-pin, and 6-pin connector configuration. Confirm your specific vehicle's factory opening size and connector type before purchasing. Will this kit retain my Toyota's factory steering wheel controls? Yes, on models fitted with the 20-pin connector. The SWC interface retains audio button functions and holds its programming if battery power is lost. Does this kit include an antenna adaptor or reverse camera retention? No. Neither an antenna adaptor nor a reverse camera retention interface is included. If your vehicle requires either, additional products will be needed. Will the head unit sit flush with my dash after installation? Not always. On some vehicles the head unit will sit forward of the factory dash panel and fascia brackets may require modification. Professional installation is recommended if fitment depth is a concern for your specific vehicle. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns, our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself, is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Aerpro AKNI27 9 and 10 Inch Trapezoid Head Unit Installation Kit for Nissan Navara D23 2019 to 2025 with Factory Navigation and 360-Degree Camera SWC Reverse Camera and USB Retention The Aerpro AKNI27 is a complete 9/10-inch trapezoid head unit installation kit for Nissan Navara D23 vehicles (2019 to 2025) fitted with factory navigation and 360-degree camera. The kit retains steering wheel controls including the phone button, factory reverse camera, factory USB input, and vehicle clock adjustment menus. The head unit ISO harness is not included and the Aerpro APP8 Head Unit Secondary ISO Harness (sold separately) is recommended. This kit suits trapezoid shaped head units only and will not suit standard DIN or double DIN radios. Product overview The AKNI27 is developed specifically for Nissan Navara D23 2019 to 2025 vehicles fitted with factory navigation and 360-degree camera systems. It includes all components required to install a 9 or 10-inch trapezoid head unit while retaining the key factory features of these vehicles. The 360-degree camera retention adaptor passes the factory camera system through to the aftermarket head unit. Steering wheel control retention includes the phone button. Factory USB is retained; AUX input and factory amplifier retention are not supported by this kit. Vehicle clock adjustment menus are retained. Compatible head units include Alpine INE-AW409S, INE-AX809, INE-AW409S-10, and INE-AX809-10; Kenwood DMX80AXS; Pioneer DMH-AP6650BT; Aerpro AM9X and AM10X; and various Android head units. Feature retention varies depending on the head unit fitted. Pioneer-specific note: this kit does not support Pioneer CAN-BUS features. On a Pioneer head unit, do not select CAN-BUS Adapter on boot-up. Instead, go to Menu, select Steering Wheel Control, then select With Adapter. Important installation notes: This kit suits trapezoid shaped radios only. It will not suit standard DIN or double DIN sized radios. This kit does not support Pioneer CAN-BUS features. On Pioneer head units, select Steering Wheel Control and then With Adapter in the menu rather than CAN-BUS Adapter on boot-up. Feature retention is head unit dependent. The head unit ISO harness is not included. The Aerpro APP8 Head Unit Secondary ISO Harness is sold separately and is recommended. Features and benefits Complete installation kit for Nissan Navara D23 2019 to 2025 with factory nav and 360 camera: All components required for a 9 or 10-inch trapezoid head unit installation in these specific Navara variants. Steering wheel control retention including phone button: Retains factory SWC buttons and phone button. SWC functions may vary from OEM depending on the head unit. 360-degree camera retention adaptor included: Passes the factory 360-degree camera system through to the aftermarket head unit. Factory reverse camera retention: Factory reverse camera display is retained on the aftermarket head unit. Factory USB retention harness included: Retains the factory USB input. AUX input and factory amplifier are not retained. Compatible with 9 and 10-inch trapezoid head units: Suits a wide range of current-model aftermarket head units in the trapezoid format. Will not suit standard DIN or double DIN radios. Gloss black fascia and adaptor included: Covers both 9-inch and 10-inch installation profiles with a gloss black finish. Antenna adaptor included: For connection between the vehicle antenna and the aftermarket head unit. Recommended with Aerpro APP8 Head Unit Secondary ISO Harness (sold separately): Simplifies the wiring connection between the kit and the aftermarket head unit. What's in the box Gloss Black Fascia Kit Steering Wheel Control Interface Harness SWC Patch Lead Gloss Black Adaptor (suits 9-inch and 10-inch radios) Antenna Adaptor 360-Degree Camera Retention Adaptor Factory USB Retention Harness Technical specs Specification Detail SKU AKNI27 Brand Aerpro Type Head Unit Installation Kit Compatible Head Unit Size 9-inch and 10-inch trapezoid Suits Nissan Navara D23 2019 to 2025 (with factory navigation and 360 camera) Fascia Finish Gloss black Vehicle feature retention Feature Retained Steering Wheel Controls Yes (including phone button) Factory Reverse Camera Yes 360-Degree Camera Yes Factory USB Input Yes AUX Input No Factory Amplifier No Vehicle Menu (Clock Adjustments) Yes Compatible head units Brand Model Alpine INE-AW409S Alpine INE-AX809 Alpine INE-AW409S-10 Alpine INE-AX809-10 Kenwood DMX80AXS Pioneer DMH-AP6650BT Aerpro AM9X Aerpro AM10X Various Android head units Frequently asked questions Which Nissan Navara variants does the AKNI27 suit? The AKNI27 suits the Nissan Navara D23 from 2019 to 2025, specifically vehicles fitted with factory navigation and 360-degree camera systems. Confirm your vehicle has both of these factory systems before purchasing. Why won't my Pioneer head unit work with CAN-BUS Adapter selected? This kit does not support Pioneer CAN-BUS features. On a Pioneer head unit, do not select CAN-BUS Adapter during the boot-up setup. Instead, go to Menu, then Steering Wheel Control, and select With Adapter. Is the head unit ISO harness included in the kit? No. The head unit ISO harness is not included. The Aerpro APP8 Head Unit Secondary ISO Harness is recommended and is sold separately. Contact us for advice on the correct harness for your head unit. Does this kit suit standard DIN or double DIN head units? No. The AKNI27 is developed for trapezoid shaped 9 and 10-inch head units only. It will not suit standard single DIN or double DIN sized radios. What factory features are not retained by this kit? The AUX input and factory amplifier are not retained by the AKNI27. Feature retention also varies depending on the aftermarket head unit fitted.Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger BN25K548H Single and Double DIN Radio Fascia Kit for Ford Ranger and Mazda BT-50 2007–2011 The BN25K548H from Stinger is a fascia kit that enables installation of a single DIN or double DIN aftermarket head unit into the Ford Ranger (PJ-PK, 2007 to 2011) and Mazda BT-50 (B Series, 2007 to 2011). Note that the universal mounting cradle (part number BKISOCT) is required for installation and is sold separately, and a universal pocket (part number BKVTP) is required when fitting a single DIN head unit, also sold separately. Product overview The Ford Ranger PJ-PK and Mazda BT-50 B Series share a common dash opening that requires a purpose-made fascia when installing an aftermarket head unit. The BN25K548H is shaped to fit this shared platform, accommodating both single DIN and double DIN radio sizes within the same kit. Unlike some fascia kits that include mounting hardware in the box, the BN25K548H requires the separately purchased BKISOCT universal mounting cradle to secure the head unit in place. When fitting a single DIN radio, the BKVTP universal pocket is also required to fill the lower opening neatly. Both accessories are available from F.A.E. and should be purchased alongside this fascia to complete the installation. Features and benefits Single and double DIN compatibility: Suits both single DIN and double DIN aftermarket head units, providing flexibility in head unit selection for both the Ford Ranger and Mazda BT-50. Shared platform fitment: Designed for the common dash architecture shared between the Ford Ranger PJ-PK and Mazda BT-50 B Series, covering both makes within a single fascia kit. Universal mounting cradle compatible: Works with the BKISOCT universal mounting cradle (sold separately), which provides the bracket support needed to secure the head unit within the fascia. Single DIN pocket support: When a single DIN head unit is installed, the BKVTP universal pocket (sold separately) fills the lower opening for a clean, finished appearance. Technical specs Specification Detail SKU BN25K548H Brand Stinger Compatible DIN Sizes Single DIN, Double DIN Required Accessory BKISOCT Universal Mounting Cradle (sold separately) Required for Single DIN BKVTP Universal Pocket (sold separately) Compatible with This fascia kit is confirmed for the following vehicles. Compatible vehicle table Make Model Variant Years Ford Ranger (PJ - PK) 2007 - 2011 Mazda BT-50 (B Series) 2007 - 2011 Frequently asked questions Does the BN25K548H include mounting brackets or a cradle?No. This fascia kit requires the BKISOCT universal mounting cradle, which is sold separately. You will need to purchase this cradle in addition to the fascia to complete the installation. Do I need anything extra when fitting a single DIN head unit with this fascia?Yes. When installing a single DIN head unit, the BKVTP universal pocket is required to fill the lower opening. It is sold separately and should be purchased alongside the BKISOCT cradle and this fascia kit. Does this fascia suit the Ford Ranger PX series?The confirmed fitment for the BN25K548H covers the Ford Ranger PJ and PK series (2007 to 2011) only. The PX series Ranger requires a different fascia. Contact us to confirm the correct kit for your vehicle. Will this fascia fit the Mazda BT-50 that shares the Ford Ranger platform?Yes. The Mazda BT-50 B Series (2007 to 2011) shares the same dash architecture as the Ford Ranger PJ-PK and is a confirmed compatible vehicle for this fascia kit. Where can I find more information about compatible head units for this fascia?For guidance on selecting a compatible head unit, harness, and antenna adapter to complete your installation, contact us and we can recommend the right combination for your vehicle. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less

Stinger BN25K2017 Double DIN Gloss Black Fascia Kit for Mitsubishi and Peugeot 2006–2018 The BN25K2017 from Stinger is a gloss black double DIN fascia kit designed for a broad range of Mitsubishi vehicles from 2006 to 2021, as well as the Peugeot 4008 (2014 to 2017). It suits models fitted with the factory MMCS radio and uses the vehicle's existing factory brackets rather than requiring separate mounting hardware. Product overview Replacing the factory MMCS head unit in Mitsubishi vehicles requires a fascia shaped to match the OEM dash opening. The BN25K2017 is purpose-built for this application, covering the Pajero, Triton, Outlander, Lancer, ASX, Challenger, and Delica across multiple series, as well as the Peugeot 4008. The gloss black finish suits the factory interior trim across all confirmed compatible models. Because this kit uses the factory mounting brackets already present in the vehicle, no additional hardware is required for installation. One fitment note applies to the 2006 to 2015 Mitsubishi Pajero: when replacing the MMCS head unit, the BN25K2017 may leave a 1 to 2mm gap between the fascia and the OE panel. If a flush finish is required in this application, the BN25K2011 is the recommended alternative. Features and benefits Double DIN fitment for MMCS-equipped models: Designed specifically for Mitsubishi vehicles factory-fitted with the MMCS multimedia system, ensuring correct alignment with the OEM dash opening when fitting a double DIN aftermarket head unit. Uses factory mounting brackets: No separate brackets are required. The BN25K2017 installs using the existing factory brackets already in the vehicle, simplifying the installation process. Gloss black finish: The high-gloss black surface complements the factory interior trim across the full range of compatible Mitsubishi and Peugeot models. Wide model coverage: Confirmed fitment across the Pajero, Triton, Outlander, Lancer, ASX, Challenger, Delica, and Peugeot 4008, spanning model years from 2006 to 2022. Rockford Amplifier variants confirmed: Specific Pajero models fitted with the factory Rockford amplifier system are confirmed compatible, covering both the 2006 to 2012 and 2013 to 2015 Rockford-equipped variants. Technical specs Specification Detail SKU BN25K2017 Brand Stinger Colour Gloss Black Mounting Brackets Uses factory brackets Compatible Radio Size Double DIN Suits Factory System MMCS Radio Compatible with This fascia kit suits models fitted with the factory MMCS radio. Note that for 2006 to 2015 Mitsubishi Pajero models, replacing the MMCS head unit with this fascia may result in a 1 to 2mm gap between the BN25K2017 and the OE panel. The BN25K2011 is the recommended alternate for a flush fit in that specific application. Compatible vehicle table Make Model Variant Years Mitsubishi ASX (XB - XC) 2013 - 2019 Mitsubishi Challenger (PC) 2013 - 2015 Mitsubishi Delica (5th Gen) 2007 - 2010 Mitsubishi Lancer Incl Evolution (CJ) 2007 - 2013 Mitsubishi Lancer Incl Evolution (CF) 2014 - 2018 Mitsubishi Outlander (ZG - ZH) 2007 - 2012 Mitsubishi Outlander (ZJ - ZK - ZL) 2013 - 2021 Mitsubishi Pajero With Rockford Amplifier 2006 - 2012 Mitsubishi Pajero (NS - NT - NW) 2006 - 2015 Mitsubishi Pajero With Rockford Amplifier 2013 - 2015 Mitsubishi Pajero (NT - NX) 2015 - 2021 Mitsubishi Pajero Sport (KR - KS - QE) 2016 - 2018 Mitsubishi Triton (MN) 2013 - 2015 Mitsubishi Triton (MQ) 2015 - 2018 Mitsubishi Triton (MR) 2019 - 2021 Mitsubishi Triton (MR) With 360 Degree Camera System 2020 - 2022 Peugeot 4008 2014 - 2017 Frequently asked questions Does the BN25K2017 include mounting brackets?No. This kit uses the factory mounting brackets already present in the vehicle. No additional brackets are required or supplied. Will this fascia fit my Mitsubishi Pajero if it has a Rockford amplifier?Yes. Specific Pajero variants fitted with the factory Rockford amplifier system are confirmed compatible, covering both the 2006 to 2012 and the 2013 to 2015 Rockford-equipped models. I have a 2006 to 2015 Pajero. Will the BN25K2017 fit flush against the OE panel?When replacing the MMCS head unit in this model range, the BN25K2017 may leave a small gap of 1 to 2mm between the fascia and the OE panel. If a completely flush result is required, the BN25K2011 is the recommended alternative. Contact us if you need assistance selecting the right option. Does the BN25K2017 suit the Mitsubishi Triton MR with a 360-degree camera system?Yes. The MR series Triton fitted with the 360-degree camera system (2020 to 2022) is a confirmed compatible variant. Note that camera system retention will depend on the head unit and harness used during installation. Is the Peugeot 4008 compatible with this fascia kit?Yes. The Peugeot 4008 (2014 to 2017) is a confirmed compatible vehicle for the BN25K2017. Contact us if you need further guidance on the correct harness and antenna adapter to complete the installation. Legendary Products & Support From Authorized Dealers When you choose Frankies BrandBeast, you're choosing quality and performance. But just as important as what you buy is where you buy it from. Here's why purchasing from an authorized dealer is always the right choice: ▸ Expert Knowledge & TrainingOnly authorized Frankies BrandBeast dealers are factory-trained to sell and install our products. They have the expertise to ensure your purchase is set up correctly and meets your expectations. ▸ Authorized Warranty ProtectionWe offer one of the best warranties in the industry, but only purchases made through authorized dealers are covered. Don’t be misled by unauthorized sellers who can’t provide genuine warranty support. ▸ Reliable Customer SupportIf you ever run into an issue, you’re backed by Frankies BrandBeast’s official manufacturer’s warranty. No need to deal with overseas returns—our local team takes care of everything quickly and efficiently. ▸ Protect Your InvestmentBuying from an authorized dealer ensures you’re getting genuine products, full warranty coverage, and expert support. Ask yourself—is saving a few bucks worth losing all that? Choose wisely. Buy from Frankies BrandBeast today!

Read more less